负载工艺对ACF担载二氧化钛光催化性能的影响

采用分散液中添加环氧树脂黏结剂并进行热处理的方法,制备出活性炭纤维(ACF)担载二氧化钛光催化材料。并对光催化材料的表面形貌和孔结构进行表征,评价复合光催化材料对亚甲基蓝溶液的光催化降解性能。重点探讨了负载方式、负载时间以及光催化剂的添加量等方面对光催化活性的影响。研究表明,当采用浸渍方式、负载时间控制在15 min左右、光催化剂添加量达11 g/L时,ACF/TiO2光催化复合材料中光催化剂负载量最佳,在15%左右,对亚甲基蓝(初始浓度为50 mg/L)的降解效果最好,在2 h内可以达到90%。     

亚甲基蓝表面修饰纳米TiO2降解造纸废水动力学

以亚甲基蓝(MB)作为表面修饰剂,采用简单的化学吸附法制备亚甲基蓝表面修饰的纳米TiO2光催化剂(TiO2-MB)。经表面修饰后,TiO2-MB光催化剂波长响应范围红移至可见光区575 nm处。探讨了光催化剂量、光照时间和溶液pH值对TiO2-MB光催化降解造纸废水的影响;研究了纳米TiO2-MB对造纸废水的暗吸附规律和光降解性能。结果表明:纳米TiO2-MB对造纸废水的吸附规律都较好地符合Langmuir和Freundlich吸附等温模型,属于吸热反应;光催化降解动力学符合Langmuir-Hinshelwood动力学模型。在160 W高压汞灯光照80 min,3.0 g/L纳米TiO2-MB光催化降解pH=2.0的造纸废水(COD:2 069.8 mg/L),COD去除率可达94.7%,处理效果远高于避光条件下。光催化剂经8次使用仍具有较高的催化活性。     

氢氧化钾改性亚麻对亚甲基蓝的吸附性能研究

以亚麻为原料,氢氧化钾为改性剂,制备了一种吸附剂,用红外光谱和扫描电子显微镜对其结构进行表征,并对其吸附亚甲基蓝的性能进行了研究。结果表明,经120℃、0.8mol/L氢氧化钾改性的亚麻对亚甲基蓝的吸附量和去除率明显提高。经优化,当pH=5、超声功率为50%(125W)、超声时间为25min、亚甲基蓝初始质量浓度为300mg/L、改性亚麻投加量为0.3g时,亚甲基蓝的去除率为95.1%,吸附量为28.54mg/g。其中,pH=5~9、亚甲基蓝初始质量浓度为300~500mg/L时,亚甲基蓝的去除率和吸附量变化不大。改性亚麻对亚甲基蓝的吸附过程符合Freundlich吸附等温式,其动力学过程符合准二级动力学方程。     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

改性累托石对镉离子吸附性能的研究

将天然累托石进行处理制备改性累托石.在静态条件下,研究了改性累托石对重金属离子Cd2 的吸附容量、等温吸附等吸附性能,同时探讨了影响吸附的因素和吸附机理.结果表明,改性累托石对Cd2 的吸附容量高.在20℃,pH=5.0～7.0、Cd2 浓度0～100 mg/L范围内,按镉与改性累托石质量比为1∶20投加改性累托石进行处理,吸附时间为90min,Cd2 去除率可达96%以上,改性累托石对Cd2 的吸附在实验浓度范围内符合符合Freundlich方程.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

光纤传导可见光降解亚甲基蓝

针对浓度大、色度高的印染废水难以处理的情况,选用加入光纤的光催化体系进行研究。采用溶胶凝胶法制备了Ag+/TiO2粉体光催化剂,用固体紫外可见光谱、X射线衍射对其进行表征。选用亚甲基蓝溶液作为目标降解物,评价了Ag+/TiO2在可见光下的光催化活性。分别考察了加入石英芯侧光光纤与塑料侧光光纤反应体系下,催化剂量、光纤数量、光照强度和pH值等因素对亚甲基蓝降解实验的影响。结果表明,选用20 mg/L的亚甲基蓝,采用催化剂量为11.67 g/L,500根侧光光纤,300 W的外部光源,pH值约为11时,光催化降解效果最佳,均能达到90%以上。     

松树锯末对亚甲基蓝（MB）的吸附研究

采用松树锯末以及改性松树锯末对模拟废水中的亚甲基蓝进行吸附实验研究。研究结果表明，当亚甲基蓝的初始浓度为50 mg/L、pH为6、锯末投加量为1 g/L时，改性前后的锯末对亚甲基蓝的吸附量最大，分别为29.9 mg/g和60.6 mg/g。同时，对改性前后的锯末做了吸附等温线拟合及动力学研究。结果表明，吸附等温线均能很好地符合Langmuir吸附模式，吸附过程符合拟二级动力学方程。     

Ru-TiO_2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru-TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明:煅烧温度600℃,掺杂1%Ru的Ru-TiO2光电极催化活性最好;以紫外灯(125 W)为光源,当外加偏压0.2 V,pH为5时,Ru-TiO2光电催化亚甲基蓝120 min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k=0.781 mmol/(L.min),吸附常数K=0.225 L/mmol。     

纳米Au/TiO2复合物光催化降解亚甲基蓝

以纳米金棒为掺杂物,采用溶胶-凝胶法制备了纳米Au/TiO2复合材料,在紫外光下对亚甲基蓝溶液进行光催化降解。结果表明,在紫外光下,Au/TiO2复合物对亚甲基蓝的脱色率最高可达99.6%,是纯TiO2的1.3倍。这主要归结于掺杂纳米尺寸的Au可增加TiO2对光的吸收以及减少电子-空穴对的复合,由此提高其光催化能力。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.