Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

Some aspects in testing and assessment of metal dust explosions

The dust explosion committee of the Association of Powder Process Industry and Engineering, Japan recently established two testing standards for dust explosions. In the investigations for the standardization, many experimental data have been obtained for the dusts currently used in Japanese industries. Data for zirconium, tantalum and silicone dusts are presented to discuss the use of test methods, which have been accepted internationally. The test methods for dust explosions have to consider a variety of kinds and forms of dusts to be tested.     

Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions

Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture.It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence.     

Assessment of the thermal hazards and oxidization mechanism of coloured corn starch dust by TG–FTIR

Starch is widely used in industrial production and in every life, and an increasing number of accidents of starch dust burning and explosions are occurring and have caused serious casualties and economic losses. Previous studies on the oxidative properties and microscopic characterization of coloured corn starch dust have been less systematic than the present study. To prevent coloured corn starch dust explosion accidents more effectively, thermogravimetry and Fourier transform infrared spectroscopy were applied to study the oxidation characteristics of coloured corn starch dust. Seven characteristic temperatures were determined from the thermogravimetric curves and derivative thermogravimetric curves of coloured corn starch dust. The entire oxidation process of coloured corn starch dust was divided into five stages, and a 60% mass loss occurred in the rapid oxidation stage. Three iso-conversion methods were used to calculate the apparent activation energy (E_a) and pre-exponential factor (A) at different oxidation stages. The value of E_a was found to be related to the difficulty of the reaction, and it had a positive correlation with lnA. Six kinds of gases were detected during the oxidation process. The oxidation mechanism was further analysed by the macro and micro characterization of the oxidation process. The findings provide a theoretical basis for preventing and controlling explosion accidents that involve coloured corn starch dust.     

Effect of pyrolysis and oxidation characteristics on lauric acid and stearic acid dust explosion hazards

The effect of pyrolysis and oxidation characteristics on the explosion sensitivity and severity parameters, including the minimum ignition energy MIE, minimum ignition temperature MIT, minimum explosion concentration MEC, maximum explosion pressure P_max, maximum rate of pressure rise (dP/dt)_max and deflagration index K_st, of lauric acid and stearic acid dust clouds was experimentally investigated. A synchronous thermal analyser was used to test the particle thermal characteristics. The functional test apparatuses including the 1.2 L Hartmann-tube apparatus, modified Godbert-Greenwald furnace, and 20 L explosion apparatus were used to test the explosion parameters. The results indicated that the rapid and slow weight loss processes of lauric acid dust followed a one-dimensional diffusion model (D1 model) and a 1.5 order chemical reaction model (F1.5 model), respectively. In addition, the rapid and slow weight loss processes of stearic acid followed a 1.5 order chemical reaction model (F1.5 model) and a three-dimensional diffusion model (D3 model), respectively, and the corresponding average apparent activation energy E and pre-exponential factor A were larger than those of lauric acid. The stearic acid dust explosion had higher values of MIE and MIT, which were mainly dependent on the higher pyrolysis and oxidation temperatures and the larger apparent activation energy E determining the slower rate of chemical bond breakage during pyrolysis and oxidation. In contrast, the lauric acid dust explosion had a higher MEC related to a smaller pre-exponential factor A with a lower amount of released reaction heat and a lower heat release rate during pyrolysis and oxidation. Additionally, due to the competition regime of the higher oxidation reaction heat release and greater consumption of oxygen during explosion, the explosion pressure P_m of the stearic acid dust was larger in low concentration ranges and decayed to an even smaller pressure than with lauric acid when the concentration exceeded 500 g/m³. The rate of explosion pressure rise (dP/dt)_m of the stearic acid dust was always larger in the experimental concentration range. The stearic acid dust explosion possessed a higher P_max, (dP/dt)_max and K_st mainly because of a larger pre-exponential factor A related to more active sites participating in the pyrolysis and oxidation reaction. Consequently, the active chemical reaction occurred more violently, and the temperature and overpressure rose faster, indicating a higher explosion hazard class for stearic acid dust.     

工业生产粉尘爆炸预防和缓解──近期研究与发展综述

本文包括三个方面，即工业粉爆的基础研究、应用研究以及粉尘点人性和可爆性。基础研究包括粉尘云的形成和点火，火焰的传播以及粉煤产生的冲击波。工业预防措施包括惰化和消除点火源。缓解的方法包括隔爆、泄爆、部分惰化、抑爆和全封闭。基础研究和应用研究相互促进。计算机模拟模型可能成为非常有效的方法，也可用于专家系统。     

Large-scale dust explosions in vessel-pipe systems

This study investigates dust explosions in vessel-pipe systems to develop a better understanding of dust flame propagation between interconnected vessels and implications for the proper application of explosion isolation systems. Cornstarch dust explosions were conducted in a large-scale setup consisting of a vented 8-m³ vessel and an attached pipe with a diameter of 0.4 m and a length of 9.8 m. The ignition location and effective dust reactivity were varied between experiments. The experimental results are compared against previous experiments with initially quiescent propane-air mixtures, demonstrating a significantly higher reactivity of the dust explosions due to elevated initial turbulence, leading to higher peak pressures and faster flame propagation. In addition, a physics-based model developed previously to predict gas explosion dynamics in vessel-pipe systems was extended for dust combustion. The model successfully predicts the pressure transients and flame progress recorded in the experiments and captures the effects of ignition location and effective dust reactivity.     

Influence of different ignition delay times on the pressure rise rate in hybrid mixture explosions in the 20-L sphere

For the development of a standardized method for measuring the explosion safety characteristics of combustible hybrid dust/vapor mixtures, the influence of the ignition delay time needs to be investigated. The ignition delay time, defined as the time between the injection of dust and the activation of the ignition source, is related to the turbulence of the mixture and thus to the pressure rise rate. The ignition source for pure vapors, however, has to be activated in a quiescent atmosphere according to the standards. Nevertheless, when measuring the explosion safety characteristics of hybrid mixtures, it is important that the dust be in suspension around the igniter. Like pure dust/air mixtures, hybrid dust/vapor/air mixtures need to be ignited in a turbulent atmosphere to keep the dust in suspension.This work will therefore investigate the influence of ignition delay times on the severity of hybrid explosions. It was generally found that at shorter ignition delay times, (dp/dt)_ex increased due to higher turbulence and decreases as the dust sinks to the bottom of the 20 L-sphere. This effect is more pronounced for hybrid mixtures with higher vapor content compared to dust content.     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.     

Explosibility of hydrogen–graphite dust hybrid mixtures

To evaluate the hazard of combined hydrogen/dust explosions under severe accident conditions in International Thermonuclear Experimental Reactor (ITER), standard method of 20-L-sphere was used to measure the explosion indices of 4-μm fine graphite dust in lean hydrogen/air mixtures. The mixtures were ignited by a weak electric spark. The tested fuel concentrations were 8–18 vol% H₂ and 25–250 g/m³ dust. If the hydrogen content is higher than 10 vol%, the dust constituent can be induced to explode by the hydrogen explosion initiated by a weak electric spark. Depending on the fuel component concentrations, the explosions proceed in either one or two stages. In two-stage explosions occurring at low hydrogen and dust concentrations, the mixture ignition initiates first a fast hydrogen explosion followed by a slower phase of the dust explosion. With increasing dust concentration, the dust explodes faster and can overlap the hydrogen-explosion stage. At higher hydrogen concentrations, the hybrid mixtures explode in one stage, with hydrogen and dust reacting at the same time scale. Maximum overpressures of hybrid explosions are higher than those observed with hydrogen alone; maximum rates of pressure rise are lower in two-phase explosions and, generally, higher in one-stage explosions, than those characteristic of the corresponding H₂/air mixtures.     

Inhibiting effects by Fe2O3 on combustion and explosion characteristics of ABS resin

The global increase in the use of, and reliance on, plastics has prompted the demand for acrylonitrile-butadiene-styrene (ABS) resin in various fields. With this increased requirement, numerous failures have occurred in the ABS process. Those incidents, resulting from electrostatic discharge, powder accumulation, heat accumulation, construction sparks, and plant fires, have caused dust fire and explosions.In this study, the ABS resin was gleaned from the site and tested for its explosion parameters, including minimum ignition temperature of dust cloud (MIT_C), minimum ignition energy (MIE), and minimum explosion concentration (MEC). To improve loss prevention in the manufacturing process, ferric oxide (Fe₂O₃) as an inert additive was added in the ABS powder. According to the MIE test, Fe₂O₃ has an apparent inhibiting effect on dust explosion for the ABS dust. With the proportion of Fe₂O₃ increased from 25 to 50 mass% in ABS, the MIE increased from 67 to 540 mJ. The explosion tests via 20-L apparatus indicated that Fe₂O₃ mixed with ABS could not increase the MEC significantly. However, the explosion pressure dropped by increasing in the ratio of Fe₂O₃ in ABS. This inerting strategy of ABS was deemed to substantially lessen the probability and severity of fire and explosion.     

Investigations into the influence of dustiness on dust explosions

A new safety characteristic the “dustiness” according to VDI 2263 – part 9 (Verein Deutscher Ingenieure, 2008) is investigated. Dustiness means the tendency of a dust to form clouds. The paper deals with the influence of the dustiness on vented dust explosions. In order to look into the effects of the dustiness on dust cloud formation and explosion properties experiments and simulations in a vertical dust dispersion glass tube apparatus were carried out.Preliminary explosion experiments showed that the dustiness has an influence on the reduced explosion pressure in a vented 75 L test apparatus. Dusts with comparable p_max and K_St values and different dustiness were tested. Dusts with higher dustiness produced higher overpressures, despite comparable safety characteristics. In order to verify the results for applications in the process industries further tests with different settings are planned as well as industrial scale experiments. Characteristics of the dust such as particle size, density, specific surface area and particle shape, which influence the dispersibility, have been determined experimentally.The Euler/Lagrange and the Euler/Euler approaches are compared for simulating an exemplary dust/air mixture. Especially sedimentation and the ability of the approaches to simulate the tendency of dust to stay airborne were investigated. The Euler/Lagrange approach is better suited for simulating local dust concentrations, particle size distributions and particle forces. It could be used to point out regions of high dust concentrations in a vessel. With the Euler/Euler method it is possible to achieve fast solutions for one specified diameter, but the simulated dust/air mixtures are always more homogenous than in reality. ANSYS CFX version 13 was used in all simulations.     

Modeling of maize starch explosions in a 12 m3 silo

This paper presents a 2-dimensional numerical model of Eulerian–Lagrangian multi-phase combustion flow to predict maize starch explosions in a 12 m³ silo. The flow field after ignition, flame propagation velocity and pressure development histories etc. during the explosion, are calculated. The data of non-uniform initial conditions including dust concentration, flow velocity and turbulent RMS velocity in the silo for this model are adopted from Hauert, Vogl and Radandt (1994) [Hauert, F., Vogl, A., Radandt, S. (1994). Measurement of turbulence and dust concentration in silos and vessels. 6th international colloquium on dust explosions (pp. 71–80), Shenyang, China, August 28–September 2, 1994.]. A simple concept of dust granule taking into consideration dust dispersion efficiency is proposed and introduced. The Lagrangian method is used to trace trajectories and granules, so it is easier to consider particle size distribution. The k−ε model is used to simulate the turbulence of the gas phase, and the particle's pulsation is modeled by random vector wind generated by the surrounding gas. In the combustion model, vaporization of water, volatilization of volatile, gas phase reaction and the particle's surface reaction are taken into account.     

Review of the DESC project

Dust Explosion Simulation Code (DESC) was a project supported by the European Commission under the Fifth Framework Programme. The main purpose of the project was to develop a simulation tool based on computational fluid dynamics (CFD) that could predict the potential consequences of industrial dust explosions in complex geometries. Partners in the DESC consortium performed experimental work on a wide range of topics related to dust explosions, including dust lifting by flow or shock waves, flame propagation in vertical pipes, dispersion-induced turbulence and flame propagation in closed vessels, dust explosions in closed and vented interconnected vessel systems, and measurements in real process plants. The new CFD code DESC is based on the existing CFD code FLame ACceleration Simulator (FLACS) for gas explosions. The modelling approach adopted in the first version entails the extraction of combustion parameters from pressure–time histories measured in standardized 20-l explosion vessels. The present paper summarizes the main experimental results obtained during the DESC project, with a view to their relevance regarding dust explosion modelling, and describes the modelling of flow and combustion in the first version of the DESC code. Capabilities and limitations of the code are discussed, both in light of its ability to reproduce experimental results, and as a practical tool in the field of dust explosion safety.     

A quantitative risk management framework for dust and hybrid mixture explosions

Dust and hybrid-mixture explosions continue to occur in industrial processes that handle fine powders and flammable gases. Considerable research is therefore conducted throughout the world with the objective of both preventing the occurrence and mitigating the consequences of such events. In the current work, research has been undertaken to help move the field of dust explosion prevention and mitigation from its current emphasis on hazards (with an accompanying reliance on primarily engineered safety features) to a focus on risk (with an accompanying reliance on hierarchical, risk-based, decision-making tools). Employing the principles of quantitative risk assessment (QRA) of dust and hybrid-mixture explosions, a methodological framework for the management of these risks has been developed.The QRA framework is based on hazard identification via credible accident scenarios for dust explosions, followed by probabilistic fault-tree analysis (using Relex – Reliability Excellence – software) and consequence severity analysis (using DESC – Dust Explosion Simulation Code – software). Identification of risk reduction measures in the framework is accomplished in a hierarchical manner by considering inherent safety measures, passive and active engineered devices, and procedural measures (in that order). An industrial case study is presented to show how inherent safety measures such as dust minimization and dust/process moderation can be helpful in reducing dust and hybrid-mixture explosion consequences in a 400-m³ polyethylene storage silo.     

Post-explosion observations of experimental mine and laboratory coal dust explosions

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine (LLEM), and after laboratory explosions in the PRL 20-L chamber and the Fike 1 m³ chamber. The dusts studied included both high- and low-volatile bituminous coals. Low temperature ashing for 24 h at 515 °C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as, or higher than the initial incombustible content. The MSHA alcohol coking test was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared with the initial dust loadings to determine the transport distance of dust during an explosion. All these data will be useful in future forensic investigations of accidental dust explosions in coal mines, or elsewhere.     

Explosibility of cork dust in methane/air mixtures

Explosibility studies of hybrid methane/air/cork dust mixtures were carried out in a near-spherical 22.7 L explosibility test chamber, using 2500 J pyrotechnic ignitors. The suspension dust burned as methane/air/dust clouds and the uniformity of the cork dust dispersion inside the chamber was evaluated through optical dust probes and during the explosion the pressure and the temperature evolution inside the reactor were measured. Tested dust particles had mass median diameter of 71.3 μm and the covered dust cloud concentration was up to 550 g/m³. Measured explosions parameters included minimum explosion concentration, maximum explosion pressures and maximum rate of pressure rise. The cork dust explosion behavior in hybrid methane/air mixtures was studied for atmospheres with 1.98 and 3.5% (v/v) of methane. The effect of methane content on the explosions characteristic parameters was evaluated. The conclusion is that the risk and explosion danger rises with the increase of methane concentration characterized by the reduction of the minimum dust explosion concentration, as methane content increases in the atmosphere. The maximum explosion pressure is not very much sensitive to the methane content and only for the system with 3.5% (v/v) of methane it was observed an increase of maximum rate of pressure rise, when compared with the value obtained for the air/dust system.     

Does your facility have a dust problem: Methods for evaluating dust explosion hazards

The hazards of dust explosions prevailing in plants are dependent on a large variety of factors that include process parameters, such as pressure, temperature and flow characteristics, as well as equipment properties, such as geometry layout, the presence of moving elements, dust explosion characteristics and mitigating measures. A good dust explosion risk assessment is a thorough method involving the identification of all hazards, their probability of occurrence and the severity of potential consequences. The consequences of dust explosions are described as consequences for personnel and equipment, taking into account consequences of both primary and secondary events.While certain standards cover all the basic elements of explosion prevention and protection, systematic risk assessments and area classifications are obligatory in Europe, as required by EU ATEX and Seveso II directives. In the United States, NFPA 654 requires that the design of the fire and explosion safety provisions shall be based on a process hazard analysis of the facility, process, and the associated fire or explosion hazards. In this paper, we will demonstrate how applying such techniques as SCRAM (short-cut risk analysis method) can help identify potentially hazardous conditions and provide valuable assistance in reducing high-risk areas. The likelihood of a dust explosion is based on the ignition probability and the probability of flammable dust clouds arising. While all possible ignition sources are reviewed, the most important ones include open flames, mechanical sparks, hot surfaces, electric equipment, smoldering combustion (self-ignition) and electrostatic sparks and discharges. The probability of dust clouds arising is closely related to both process and dust dispersion properties.Factors determining the consequences of dust explosions include how frequently personnel are present, the equipment strength, implemented consequence-reducing measures and housekeeping, as risk assessment techniques demonstrate the importance of good housekeeping especially due to the enormous consequences of secondary dust explosions (despite their relatively low probability). The ignitibility and explosibility of the potential dust clouds also play a crucial role in determining the overall risk.Classes describe both the likelihood of dust explosions and their consequences, ranging from low probabilities and limited local damage, to high probability of occurrence and catastrophic damage. Acceptance criteria are determined based on the likelihood and consequence of the events. The risk assessment techniques also allow for choosing adequate risk reducing measures: both preventive and protective. Techniques for mitigating identified explosions risks include the following: bursting disks and quenching tubes, explosion suppression systems, explosion isolating systems, inerting techniques and temperature control. Advanced CFD tools (DESC) can be used to not only assess dust explosion hazards, but also provide valuable insight into protective measures, including suppression and venting.     

Methods for more accurate determination of explosion severity parameters

Accurate determination of explosion severity parameters (p_max, (dp/dt)_max, and K_St) is essential for dust explosion assessment, identification of mitigation strategy, and design of mitigation measure of proper capacity. The explosion severity parameters are determined according to standard methodology however variety of dust handled and operation circumstances may create practical challenge on the optimal test method and subsequent data interpretation. Two methods are presented: a statistical method, which considers all test results in determination of explosion severity parameters and a method that corrects the results for differences of turbulence intensity. The statistical method also calculates experimental error (uncertainty) that characterises the experimental spread, allows comparison to other dust samples and may define quality determination threshold. The correction method allows to reduce discrepancies between results from 1 m³ vessel and 20-l sphere caused by difference in the turbulence intensity level. Additionally new experimental test method for difficult to inject samples together with its analysis is described. Such method is a versatile tool for explosion interpretation in test cases where different dispersion nozzle is used (various turbulence level in the test chamber) because of either specific test requirements or being “difficult dust sample”.     

Solid inertants and their use in dust explosion prevention and mitigation

This paper is a review of the use of inert dusts to reduce the risk of dust explosions through both prevention and mitigation schemes. The review is conducted by referring primarily to the research results of the author and his colleagues in this area, with appropriate reference to the work of other researchers. A functional distinction is first made between inerting and suppression by explaining each term within the contexts of explosion prevention and explosion mitigation, respectively. The use of solid inertants is then described in terms of the various inhibitor and situation-specific parameters that can influence their effectiveness. Finally, application examples of the research results are given for research laboratories, test facilities, design engineers, and industrial practitioners.