微生物代谢与Fe3+催化氧化脱除烟气中SO2的研究

利用自制的鼓泡反应器,进行了含氧化亚铁硫杆菌的酸性铁溶液脱除烟气中SO2的实验研究.结果表明,细菌直接脱硫的效果较差;Fe3 在脱硫实验过程中既有催化作用,又有氧化作用;细菌主要起氧化Fe2 为Fe3 的作用,再通过Fe3 脱硫.Fe3 存在一个最佳质量浓度,在7～8 g/L左右.当初始Fe3 质量浓度为7.37 g/L时,脱硫10 h,其效率仍高达80%.     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物,研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H2O溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,实验结果表明：H2O浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱除率影响显著,pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98．5％以上,脱硝效率最高达到67．4％。     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物,研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H₂O₂溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,实验结果表明：H₂O₂浓度、反应温度、NO浓度、SO₂浓度、烟气流量对脱除率影响显著,pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98.5%以上,脱硝效率最高达到67.4%。     

湿法烟气脱硫反应过程的实验研究

在石灰石/石膏湿法烟气脱硫中试台上,系统开展了浆液pH值、飞灰浓度、液气比、入口SO2浓度、烟气速度和氧化方式等对脱硫反应过程影响的实验研究。实验表明,脱硫效率随着石膏浆液pH值、液气比的升高而增加,且入口SO2浓度越高,液气比越低,影响效应越明显;脱硫效率随着烟气速度、烟气温度和入口SO2浓度的增加而下降;石膏浆液中飞灰含量对系统脱硫效率具有一定的促进作用:pH值>5.6,飞灰浸出液中Fe3+含量相对较低,Fe3+对脱硫反应过渡态催化氧化影响程度较轻,不同工况脱硫效率差别不大。pH值<5.6,飞灰浸出液中Fe3+含量随pH值降低而增大,增效效果逐渐显著;氧化方式对脱硫反应过程有明显的影响,强制氧化工艺的脱硫效率比自然氧化的高5%左右。     

K2Cr2O7溶液同时脱硫脱硝实验研究

采用K2Cr2O7溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,考察多种因素对SO2脱除率(即脱硫率)和NO脱除率(即脱硝率)的影响。实验结果表明:K2Cr2O7浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱硫率、脱硝率影响显著;当烟气流量为0.4L/min,气相中O2体积分数为6%,SO2体积分数为0.09%,NO体积分数为0.100%,K2Cr2O7摩尔浓度为10mmol/L,反应温度为40℃时,脱硫率、脱硝率分别达到100%和64.3%。     

氧化镁烟气脱硫反应特性研究

利用实验室规模的鼓泡式反应装置,对比了碳酸钙、氧化镁和氧化镁/硫酸镁脱硫剂的反应活性,证实脱硫液中高浓度硫酸镁的存在是保证镁法脱硫效率高于钙法的重要因素,并考察了硫酸镁浓度、脱硫剂(氧化镁)浓度、烟气量、SO2浓度和吸收液温度等因素对脱硫效率的影响。结果表明,脱硫反应可以根据pH分为2个不同阶段;反应过程中脱硫效率随着硫酸镁浓度的增加而显著升高;烟气量增加将会导致脱硫效率有所下降;入口SO2浓度升高,脱硫效率下降;氧化镁浓度、温度对脱硫效率影响不显著。结合实验现象进行推断,氧化镁脱硫的反应过程受SO2在气液两相界面的传质扩散和其水解产物在液相的扩散控制。     

喷射鼓泡法烟气脱硫工艺

对以喷射鼓泡反应器为主设备，石灰石浆液为脱硫剂的湿法烟气脱硫工艺进行了实验研究，结果表明主要参数[烟气压降Δp、ф（液气）比、吸收液pH值、进气SO2浓度]对脱硫效率均有较大的影响。     

低浓度软锰矿浆烟气脱硫过程中的催化作用

通过对SO2-4浓度的分析,研究了低浓度软锰矿浆烟气脱硫过程中的液相和固相催化作用.研究表明:低浓度软锰矿浆中Fe(Ⅱ,Ⅲ)的浸出率很低(＜ 7%),致使Fe(Ⅱ,Ⅲ)离子的液相催化作用和Mn(Ⅱ)、Fe(Ⅱ,Ⅲ)离子间的液相协同作用不明显.该过程中实际生成的so2-4主要来自3个方面:MnO2的直接氧化还原作用,Mn(Ⅱ)的液相催化作用以及软锰矿固相组分的催化作用.其中,Mn(Ⅱ)的液相催化作用始终占据主导地位;MnO2的直接氧化还原作用与固相催化作用相比,在20 min前有明显的优势,而20 min后则几乎可以忽略不计.     

pH、接种量及固形物含量对氧化亚铁硫杆菌LX5煤炭生物脱硫的影响

高硫煤燃烧释放SO2污染环境。采用摇瓶实验,以FeS2驯化的嗜酸性氧化亚铁硫杆菌(Acidithiobacillus ferrooxidans)LX5为供试菌株,研究了pH、接种量及煤粉数量对菌株LX5进行生物脱硫的影响。实验结果表明,在15 d的反应周期中反应液的起始pH为2.0、2.5、3.0和4.0时,菌株LX5的脱硫效率分别为43.1%、73.3%、61.9%和37.3%;将菌株LX5的接种量控制为5%、10%及15%时,其脱硫效率分别为44.2%、68.1%及72.2%;将煤粉含量调整为5%、10%及15%时,LX5的脱硫效率分别为73.1%、72.2%及56.3%。摇瓶实验确定的最合适的生物脱硫条件是:培养液起始pH为2.5,LX5接种量为培养液体积的10%,煤粉加入量为培养液质量的10%。在5 L序批式反应器进行煤炭生物脱硫的启动实验,研究表明,反应15 d后煤炭脱硫率达到69.2%,而煤中黄铁矿硫的脱硫率可达78%。     

铁离子液相催化氧化协同脱硫脱硝

在铁法脱硫的基础上,利用Fe(Ⅲ)离子可以催化氧化NO_x与SO_2溶于液相中形成的S(IV)化合物发生反应的特性,在鼓泡反应器中进行了铁离子液相催化氧化协同脱除烟气中SO_2和NO_x的实验研究,考察了吸收液pH值、温度、烟气中SO_2和NO_x的浓度比等因素对SO_2和NO_x脱除效率的影响。结果表明:实验条件下影响因素的改变并未对SO_2脱除效率产生影响,其脱除效率一直维持在95%以上;对NO_x的脱除效率影响较大,吸收液pH值在3.0左右时,NO_x脱除效率最高,其脱除率可达62%;温度和烟气中SO_2和NO_x的浓度比的增大都会在一定程度上提高NO_x的脱除效率。仅当吸收液温度增大到50℃以后,溶液中Fe(Ⅲ)离子水解生成絮凝状沉淀时,NO_x的脱除效率开始下降;另外,SO_2和NO_x的浓度比大于2.3∶1时,即可满足NO_x脱除的需要。     

Removal of NOx from Flue Gas with Iron Filings Reduction Following Complex Absorption in Ferrous Chelates Aqueous Solutions

Abstract

A novel process for removal of nitrogen oxides (NO_x) from flue gases with iron filings reduction following complex absorption in iron-ethylenediaminetetraacetic acid aqueous solution is proposed. The reaction mechanism involved in the process is discussed briefly. The parameters influencing the process, including the concentration of ferrous chelates, initial pH, amount of iron filings, temperature, flow rate of the flue gas, and inlet nitric oxide concentration and oxygen content of the flue gas, are researched in detail. The optimal NO_x removal conditions are established. The regeneration and circular utilization of the absorption solution also is studied.     

Removal of NOx from flue gas with iron filings reduction following complex absorption in ferrous chelates aqueous solutions

A novel process for removal of nitrogen oxides (NOx) from flue gases with iron filings reduction following complex absorption in iron-ethylenediaminetetraacetic acid aqueous solution is proposed. The reaction mechanism involved in the process is discussed briefly. The parameters influencing the process, including the concentration of ferrous chelates, initial pH, amount of iron filings, temperature, flow rate of the flue gas, and inlet nitric oxide concentration and oxygen content of the flue gas, are researched in detail. The optimal NOx removal conditions are established. The regeneration and circular utilization of the absorption solution also is studied.     

采用杂多酸化合物溶液同时脱硫脱氮的实验研究

本文对液相催化氧化脱硫脱氮的新方法进行了研究 ,在鼓泡反应发生器内进行了液相催化氧化脱硫脱氮的实验。采用钼硅酸溶液及其还原产物脱除烟气中的SO2 和NOX,分别就吸收液的浓度、pH值、温度、停留时间等因素对SO2 和NOX 去除效率的影响及其变化规律进行了研究。实验结果表明 ,钼硅酸能十分有效地吸收SO2 ,将SO2 氧化成H2 SO4,并使杂多酸还原为杂多蓝。随后又被用于去除NOX,把NOX 还原成N2 ,蓝色溶液再次被氧化成为黄色溶液     

Technical Description of Parameters Influencing the pH Value of Suspension Absorbent Used in Flue Gas Desulfurization Systems

Abstract

As a result of the large limestone deposits available in Poland, the low cost of reagent acquisition for the large-scale technological use and relatively well-documented processes of flue gas desulfurization (FGD) technologies based on limestone sorbent slurry, wet scrubbing desulfurization is a method of choice in Poland for flue gas treatment in energy production facilities, including power plants and industrial systems. The efficiency of FGD using the above method depends on several technological and kinetic parameters, particularly on the pH value of the sorbent (i.e., ground limestone suspended in water). Consequently, many studies in Poland and abroad address the impact of various parameters on the pH value of the sorbent suspension, such as the average diameter of sorbent particles (related to the limestone pulverization degree), sorbent quality (in terms of pure calcium carbonate [CaCO₃] content of the sorbent material), stoichiometric surfeit of CaCO₃ in relation to sulfur dioxide (SO₂) absorbed from flue gas circulating in the absorption node, time of absorption slurry retention in the absorber tank, chlorine ion concentration in sorbent slurry, and concentration of dissolved metal salts (Na, K, Mg, Fe, Al, and others). This study discusses the results of laboratory-scale tests conducted to establish the effect of the above parameters on the pH value of limestone slurry circulating in the SO₂ absorption node. On the basis of the test results, a correlation equation was postulated to help maintain the desirable pH value at the design phase of the wet FGD process. The postulated equation displays good coincidence between calculated pH values and those obtained using laboratory measurements.     

氢氧化钠-钢渣双碱法烧结烟气脱硫工艺

在鼓泡反应器中考察了氢氧化钠-钢渣双碱法烧结烟气脱硫的主要影响因素。结果表明,在温度为常温,钢渣反应时间为2 h,钢渣加入量为40 g,SO2进口浓度为2 400 mg/m3,钢渣粒径为200目以上,烟气流量为0.05 m3/h,循环液pH保持在7～8,Na+浓度为0.5 mol/L,循环液为500 mL的条件下,脱硫率可长时间保持在80%以上。同时,对钢渣-氢氧化钠双碱法烧结烟气脱硫机理进行了探讨。     

Removal characteristics of sulfuric acid aerosols from coal-fired power plants

With increasing attention on sulfuric acid emission, investigations on the removal characteristics of sulfuric acid aerosols by the limestone gypsum wet flue gas desulfurization (WFGD) system and the wet electrostatic precipitator (WESP) were carried out in two coal-fired power plants, and the effects of the WFGD scrubber type and the flue gas characteristics were discussed. The results showed that it was necessary to install the WESP device after desulfurization, as the WFGD system was inefficient to remove sulfuric acid aerosols from the flue gas. The removal efficiency of sulfuric acid aerosols in the WFGD system with double scrubbers ranged from 50% to 65%, which was higher than that with a single scrubber, ranging from 30% to 40%. Furthermore, the removal efficiency of WESP on the sulfuric acid aerosols was from 47.9% to 52.4%. With increased concentrations of SO₃ and particles in the flue gas, the removal efficiencies of the WFGD and the WESP on the sulfuric acid aerosols were increased.

Implications: Investigations on removal of sulfuric acid aerosols by the WFGD and the WESP in the power plants were aimed at the control of sulfuric acid emission. The results showed that the improvement of the WFGD system was beneficial for the reduction of sulfuric acid emission, while the WESP system was essential to control the final sulfuric acid aerosol concentration.     

湿式烟气脱硫系统同时脱汞研究

研究表明,湿法烟气脱硫装置(WFGD)可去除烟气中绝大部分Hg²⁺,但对单质汞的吸收效果不明显,因此研究提高湿法烟气脱硫系统中单质汞的氧化率的方法对控制汞的排放具有重要意义。综述了WFGD及在此系统中各种添加剂的脱汞性能,认为在添加剂中,气态的臭氧、液态的次氯酸和氯化钠稀溶液、 黄磷乳浊液、氢硫化钠溶液及EDTA的汞去除效果较好,且不会被SO₂大量消耗,可在WFGD系统实现同时脱硫脱汞;而气态的氯气,液态的K₂S₂O₈溶液虽然也有较好的汞去除效果,但因易被SO₂或亚硫酸盐溶液消耗,当在WFGD系统中用其氧化单质汞时,需要对脱硫塔进行分层或其他改造,使烟气中的SO₂被吸收后再控制汞,提高经济性。     

烧结烟气脱硫剂性能的研究

为了提高脱硫效率和合理利用烧结过程中产生的机头灰,在半干法烟气脱硫剂生石灰中,加入一定量的烧结机头灰作为脱硫催化剂。在测定机头灰与生石灰化学成分、粒度和比表面积的基础上,研究和分析了机头灰与生石灰的质量配比对于脱硫效率的影响。结果表明,脱硫剂与机头灰在粒径分布和比表面积上都较接近,但经过消化活化后的混合脱硫剂的比表面积明显增大。当机头灰添加量为脱硫剂质量的2%～5%时,脱硫效率提高了2%～3%。机头灰与生石灰的胶凝反应以及机头灰中Fe2O3的催化作用是主要的作用机理。