钒硅催化脱硫脱硝的研究

考察了经10% H2-90% Ar(体积分数)还原的钒硅催化剂在固定床石英玻璃反应器中的脱硫脱硝活性,研究了反应温度、SO2/NO摩尔比及O2浓度对SO2和NO脱除率的影响.结果表明,还原后的钒硅催化剂的平均NO脱除率提高了15%左右;反应温度对脱硫脱硝影响较大,当温度为400℃以上时SO2和NO脱除率基本保持稳定;SO2/NO摩尔比为2和5时,钒硅催化剂的NO脱除率较高;模拟烟气中有O2条件下的脱硫脱硝活性明显高于无O2条件,O2体积分数为6.00%时SO2和NO脱除率达到最大.     

聚丙烯腈基活性碳纤维用于烟气脱硫脱硝

应用聚丙烯腈基活性碳纤维(PAN-ACF)对模拟的工业烟气中的SO2和NO在烟气露点温度以上进行吸附脱除实验。通过改变固定床ACF装载量、反应温度、水蒸气体积分数和O2体积分数,研究了ACF脱硫效率和脱硝效率的变化规律,还研究了同时脱硫脱硝时入口SO2或NO浓度对脱除效率的影响。结果表明:PAN-ACF具有良好的脱硫性能和一定的脱硝能力,其脱硫效率和脱硝效率随着ACF装载量和O2体积分数的增大而升高,随着温度的升高而降低,随着水蒸气体积分数的增大先升高后降低;在同时脱硫脱硝时,SO2对ACF的脱硝反应有明显的抑制作用,而NO对ACF的脱硫反应影响不大。     

改进氨吸收法同时脱硫脱硝试验研究

以氨水和尿素作为混合吸收剂,同时以三乙醇胺作为添加剂,进行了模拟工业锅炉烟气同时脱硫脱硝试验。考察了SO2和NO的初始浓度、尿素和三乙醇胺的质量分数、氨水体积分数、烟气流量、液气比和反应温度对脱硫脱硝效果的影响。结果表明,当NO初始质量浓度为1 000mg/m3,SO2初始质量浓度为1 780mg/m3,尿素质量分数为0.3%,氨水体积分数为0.3%,三乙醇胺质量分数为0.02%,烟气流量为20m3/h,液气比为20L/m3,温度为20℃时,脱硫率为97%,脱硝率为58.7%。该方法可以达到同时脱硫脱硝的目的。     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物，研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H2O溶液作为吸收液，在自制的鼓泡反应器内，对模拟烟气进行同时脱硫脱硝的实验研究，实验结果表明：H2O浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱除率影响显著，pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98．5％以上，脱硝效率最高达到67．4％。     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物，研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H₂O₂溶液作为吸收液，在自制的鼓泡反应器内，对模拟烟气进行同时脱硫脱硝的实验研究，实验结果表明：H₂O₂浓度、反应温度、NO浓度、SO₂浓度、烟气流量对脱除率影响显著，pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98.5%以上，脱硝效率最高达到67.4%。     

鼓泡反应器中液相络合催化同时脱硫脱硝的研究

在鼓泡反应器中考察了[Co(en)3]2+同时吸收去除SO2和NO的影响因素,实验结果表明,pH值和脱硫剂种类是影响乙二胺合钴同时脱除NO和SO2的最重要影响因素,烟气中的氧促进乙二胺合钴吸收NO和SO2,烟气中的SO2,CO2和NO2对乙二胺合钴吸收NO具有抑制作用。在实验条件温度为20℃,pH为13.0,[Co(en)3]2+浓度为0.025 mol/L,加入1 g NH3.H2O的脱硝率更好,连续吸收60 min,脱硝率均保持在93.5%,加入NaOH和NH3.H2O的脱硫效果最好。乙二胺合钴络合同时脱除NO和SO2完全可以在一个装置中完成。     

活性炭法烟气脱硫脱硝试验研究

将活性炭法烟气脱硫脱硝工艺和循环流化床技术相结合,在自行设计的试验台上进行烟气同时脱硫脱硝试验。结果表明,活性炭给料量及烟气流量对脱硫脱硝效果的影响较小;在烟气排放温度范围(100～200℃)内,升高温度对脱硝有促进作用,对脱硫有抑制作用;水蒸气对脱硫效果的影响大于脱硝,其最佳工作区域为10%～12%(质量分数);SO2浓度的增加会降低脱硫脱硝效果,而NO浓度的增加对脱硫有促进作用,对脱硝影响不大;当NH3∶NO摩尔比达到1∶1时,可得到最佳脱硝效果,此时工艺的脱硫率>70%,脱硝率>40%。     

NaClO2/NaClO复合吸收液同时脱硫脱硝

针对NaClO2氧化吸收法脱硫脱硝成本过高,难以实现工业化的现状,提出了以NaClO2/NaClO为复合吸收剂的同时脱硫脱硝新方法,比单独NaClO2方法效率高,成本低。考虑实际工况条件,给定SO2与NO的初始浓度分别为2 850 mg/m3和670 mg/m3。结果表明,吸收液初始pH为6.0,液气比L/G为20 L/m3,反应温度为55℃时,平均脱硫脱硝效率分别可达99.8%和94.0%。在此基础上对反应机理进行了分析,总结出实验反应主反应方程式。该方法设备简约,操作简单,容易实现全自动控制,综合成本可以接受,比较适合中小型燃煤锅炉的烟气污染治理。     

旋转填料床/柠檬酸盐法吸收-解吸SO2

提出采用旋转填料床结合柠檬酸盐法脱除烟气中SO2的方法,考察了旋转填料床转子转速、液气比、初始柠檬酸根浓度和初始pH值等因素对脱硫效率的影响。结果表明,采用超重力法超重机转子转速为1 000 r/min、液气比为7L/m3、初始柠檬酸根浓度为1.5 mol/L、吸收液的初始pH值为5.0,脱硫效率稳定在99%左右。研究了水蒸气汽提法解吸SO2时初始柠檬酸根浓度、初始pH值、SO2浓度、富液流量和水蒸气流量对解吸效率的影响,得出了影响SO2解吸率的基本规律,并进行了分析。通过实验证明该方法在技术上是可行的,具有良好的应用前景。     

基于亚硫酰基催化剂的烟气脱硫脱硝

利用核心成分为亚硫酰基的官能团进行了燃煤电站脱硫脱硝一体化研究。利用臭氧将烟气中的NO氧化为NO2,易溶于水的NO2及SO2则与水、氧气、氨水反应,最终生成硫酸铵及硝酸铵可作为复合肥的原材料。使用催化剂能够降低臭氧的消耗量。避免诸如亚硫酸盐等副产物的生成。通过在集装箱内搭建小型实验装置可直接抽取实际烟气,烟气处理量达到100 m3·h~(-1)。针对烟气温度、催化剂浓度、催化剂类型、O3/NOx比例等参数对污染物脱除效率的影响进行了研究。结果表明,上述参数变化对脱硫效率影响有限,脱硫效率始终能够稳定在99%以上。烟气温度越低,脱硝效率越高;脱硝效率最高能够达到88%。此外,为了降低运行成本,采用双氧水替代臭氧进行烟气氧化,其脱硝效率能够达到68%。     

采用杂多酸化合物溶液同时脱硫脱氮的实验研究

本文对液相催化氧化脱硫脱氮的新方法进行了研究 ,在鼓泡反应发生器内进行了液相催化氧化脱硫脱氮的实验。采用钼硅酸溶液及其还原产物脱除烟气中的SO2 和NOX,分别就吸收液的浓度、pH值、温度、停留时间等因素对SO2 和NOX 去除效率的影响及其变化规律进行了研究。实验结果表明 ,钼硅酸能十分有效地吸收SO2 ,将SO2 氧化成H2 SO4,并使杂多酸还原为杂多蓝。随后又被用于去除NOX,把NOX 还原成N2 ,蓝色溶液再次被氧化成为黄色溶液     

超重力脱除模拟烟气中一氧化氮简

以NO和N₂的混合气作模拟烟气，以酸性尿素溶液为吸收剂，在超重力机中进行了脱除模拟烟气中NO实验研究。实验考察了混合气中NO初始含量、进气流量、吸收液流量、超重力机转速对NO脱除率的影响，确定了在超重力中尿素吸收NO的适宜条件。实验结果表明，在常温常压下，N₂体积流量为1.0 m³/h，控制NO初始浓度为3 300 mg/m³，吸收液流量为250 L/h，超重力机转速为650 r/min时，NO脱除率可达89.5%。     

Mercury removal from incineration flue gas by organic and inorganic adsorbents

Experiments were performed to investigate various adsorbents for their mercury removal capabilities from incineration flue gases. Four different materials were tested; Zeolite, Bentonite, activated carbon (AC), and wood char. Real incineration off-gas and in-lab simulated combustion flue gases (N2 + Hg) were used. Three cylindrical-shaped sorbent columns with 5 cm in diameter and 20 cm in length were used. The gas flow rate was fixed at 660 l/h at all times. Concentrations of NO, CO, O2, CO2, SO2, H2O, HCl, and mercury were continuously monitored. Mercury removal efficiencies of natural Zeolite and Bentonite were found to be much lower than those of the referenced AC. Amount of Hg removed were 9.2 and 7.4 microg/g of Zeolite and Bentonite, respectively. Removal efficiencies of each layer consisted of inorganic adsorbents were no higher than 7%. No significant improvement was observed with sulfur impregnation onto the inorganic adsorbents. Organic adsorbents (wood char and AC) showed much higher mercury removal efficiencies than those of inorganic ones (Zeolite and Bentonite). Mercury removal efficiency of wood char reached over 95% in the first layer, showing almost same effectiveness as AC which currently may be the most effective adsorbents for mercury. Amount of mercury captured by wood char was approximately 0.6 mg/g of wood char, close to the amount captured by AC tested in this study. Hence, wood char, made from the waste woods through a gasification process, should be considered as a possible alternative to relatively expensive AC.     

Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution

An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers.     

Simultaneous removal of NO and SO2 by high-temperature fluidized zero-valent iron processes

A new approach to simultaneously remove nitrogen monoxide (NO) and sulfur dioxide (SO2) by zero valent iron (ZVI) was investigated. Three different parameters, temperature, flux, and ZVI dosage, were tested in fluidized ZVI column studies containing 500 ppmv of NO and SO2, respectively. Under the ZVI dosage of 0.5 g at flux of 0.6 L/cm2 x min for temperature 573 K, there is neither NO nor SO2 reduction. For 623 K and 673 K, complete removal for NO and > 90% removal for SO2 were achieved. For temperatures of 723 K and 773 K, 100% removal was achieved for both NO and SO2. The amounts of NO or SO2 reduction (as milligrams of NO or SO2 per gram ZVI) increased as temperature increased, and linearities were observed with both correlation coefficients > 0.97. Compared with NO, SO2 had earlier breakthrough because of a slower diffusion rate and less reactivity but higher mass reduction because of a higher molecular weight for SO2 (64 g/mol for SO2 and 30 g/mol for NO). At same temperature, both NO and SO2 reductions (as milligrams of NO or SO2 per gram of ZVI) were constant regardless of either flux or ZVI dosage variation, but breakthrough time was affected by both flux and ZVI dosage. A parameter weight of ZVI/flux (W/F) was developed to represent these two parameters at the same time to assess the breakthrough time of NO and SO2. Higher breakthrough time was achieved for higher W/F value. Moreover, interestingly, longer breakthrough time and more NO and SO2 mass reduction were achieved for combined NO and SO2 than individual NO or SO2 treated by ZVI, and both oxidation and reduction reactions occurred instead of a reduction reaction only. Chemical reactions among ZVI/NO, ZVI/ SO2, and ZVI/NO/SO2 were also proposed and verified by X-ray diffraction analyses.     

Effect of solution pH on SO2, NO(x), and Hg removal from simulated coal combustion flue gas in an oxidant-enhanced wet scrubber

This paper presents a study on the simultaneous removal of SO2, NO(x) and Hg (both Hg0 and Hg2+) from a simulated flue gas by oxidant injection in a bench-simulated wet limestone scrubber for a wide range of slurry pH. The slurry pH strongly influenced the chemical mechanism in the scrubber and, therefore, affected pollutant removal. This paper also examines the potential ClO2(gas) reemission from a developed multipollutant scrubber at different slurry pHs. To better understand the chemical mechanisms at each slurry pH and to apply a mass balance to the process, detailed product ion analyses were performed for all experiments. Ion analysis covered three different chlorine species (chlorite, chloride, chlorate), sulfate, nitrite and nitrate. Different NO(x) removal efficiencies and mechanisms were found in acidic and alkaline pHs in the multipollutant scrubber. The acidic solution was favorable for NO and Hg0 oxidation, but increasing the slurry pH above 7.0 was disadvantageous for NO and Hg oxidation/removal. However the rate of NO(x) absorption (by percentage) was higher for the alkaline solution.     

垃圾渗滤液烟气脱硫体系的实验研究

利用垃圾渗滤液中较高的碱度吸收二氧化硫是垃圾渗滤液湿法烟气脱硫工艺的第一阶段。试验证明 ,垃圾渗滤液可高效吸收二氧化硫 (去除率可达 90 %以上 ) ;同时垃圾渗滤液中氨氮浓度由 133mmol L降至 78mmol L。实验结果证实了所建立的垃圾渗滤液烟气脱硫体系的互补性     

The impact of wet flue gas desulfurization scrubbing on mercury emissions from coal-fired power stations

This article introduces a predictive capability for Hg retention in any Ca-based wet flue gas desulfurization (FGD) scrubber, given mercury (Hg) speciation at the FGD inlet, the flue gas composition, and the sulphur dioxide (SO2) capture efficiency. A preliminary statistical analysis of data from 17 full-scale wet FGDs connects flue gas compositions, the extents of Hg oxidation at FGD inlets, and Hg retention efficiencies. These connections clearly signal that solution chemistry within the FGD determines Hg retention. A more thorough analysis based on thermochemical equilibrium yields highly accurate predictions for total Hg retention with no parameter adjustments. For the most reliable data, the predictions were within measurement uncertainties for both limestone and Mg/lime systems operating in both forced and natural oxidation mode. With the U.S. Environmental Protection Agency's (EPA) Information Collection Request (ICR) database, the quantitative performance was almost as good for the most modern FGDs, which probably conform to the very high SO2 absorption efficiencies assumed in the calculations. The large discrepancies for older FGDs are tentatively attributed to the unspecified SO2 capture efficiencies and operating temperatures and to the possible elimination of HCl in prescrubbers. The equilibrium calculations suggest that Hg retention is most sensitive to inlet HCl and O2 levels and the FGD temperature; weakly dependent on SO2 capture efficiency; and insensitive to HgCl2, NO, CA:S ratio, slurry dilution level in limestone FGDs, and MgSO3 levels in Mg/lime systems. Consequently, systems with prescrubbers to eliminate HCl probably retain less Hg than fully integrated FGDs. The analysis also predicts re-emission of Hg(O) but only for inlet O2 levels that are much lower than those in full-scale FGDs.