利用强化混凝去除水源水中天然有机物的研究进展

总结了近年来利用强化混凝去除水源水中天然有机物的研究,重点讨论了其作用机理和主要影响因素.水源水中天然有机物的含量和成分会因水源地和时间的不同而存在差异,对水源水中天然有机物的了解是保证强化混凝效果的基本前提.不同混凝条件下,强化混凝的主导作用机理不同.铁盐混凝剂、较低pH值、较高混凝剂投量和阳离子有利于提高强化混凝的效果.     

污水处理对黑水/灰水中溶解性有机物紫外光谱及荧光光谱特性的影响

为了考察黑水/灰水中溶解性有机物(DOM)光谱特征在污水处理过程中的变化规律以及生物处理前后黑水/灰水中DOM特性上的异同,对污水处理过程中黑水/灰水DOM的紫外光谱及荧光光谱特征进行了测定分析。结果表明,黑水原水中DOM的含量远高于灰水,且含有较多难降解有机物。生物处理可实现对黑水与灰水中易降解DOM的有效去除,MBR系统中的膜分离过程也可以起到截留溶解性有机物的作用。经MBR处理后,同黑水出水相比,灰水出水中的DOM含量更低,且主要为饱和有机物,苯环C骨架的聚合程度较高,THMs生成活性更低。生物处理过程可有效去除黑水/灰水中蛋白质类物质与易降解腐殖质类物质。生物处理后,黑水与灰水的蛋白峰均消失,黑水出水类腐殖酸峰F荧光强度高于灰水出水。与黑水出水相比,灰水出水更适用作再生水加以回收利用。     

利用强化混凝去除水源水中天然有机物的研究进展

总结了近年来利用强化混凝去除水源水中天然有机物的研究，重点讨论了其作用机理和主要影响因素。水源水中天然有机物的含量和成分会因水源地和时间的不同而存在差异，对水源水中天然有机物的了解是保证强化混凝效果的基本前提。不同混凝条件下，强化混凝的主导作用机理不同。铁盐混凝剂、较低pH值、较高混凝剂投量和阳离子有利于提高强化混凝的效果。     

外加气体对等离子体降解水相中有机污染物的影响研究

研究了等离子体在内电极通氧气、氮气、空气和氦气条件下降解甲基紫的机理。研究表明，在该等离子体发生器结构下，等离子体能降解甲基紫，且在不同气体气氛下的降解产物不同，在氧气氛围下为含-CO和-OH物质及直链烯烃，而氮气氛围下是含-N、-NH和-OH的芳香类物质及小分子烃类物质。研究同时表明，等离子体降解水相中有机物时应在氧气介质中进行，如用空气则有可能会造成水体中NO3^-过高。     

太阳光对湖泊中有机污染物降解的研究进展

论述了太阳光对湖泊水体中有机污染物降解作用的研究,就其降解机理、动力学特征、作用对象及降解产物等作了逐一介绍.阐明了太阳光对生物降解湖泊水体中有机污染物具有协同作用,也概述了光降解作用受pH、溶解性有机物(DOM)、水深与水体运动、地理、水文、水质与气候等因素的影响.并对实验室模拟条件下的降解与自然条件下的降解进行对比,提出今后该领域的发展前景与研究方向.     

密云水源水的预臭氧化及强化常规处理研究

针对北京密云水库水的水质特征,分别进行了实验室烧杯和现场中试研究.实验结果表明,预臭氧化能使原水中较大粒径颗粒数目减少,并能显著降低原水中不饱和有机物的含量;高效聚合氯化铝在颗粒物及有机物的去除上明显优于传统的聚合氯化铝和硫酸铝;预臭氧化与常规处理的联合工艺对浑浊度、有机物和大肠菌群有很高的去除率.     

厌氧-跌水充氧接触氧化工艺有机物降解数学模型

厌氧-跌水充氧接触氧化-人工湿地组合工艺是一种新型的污水处理工艺,为优化该工艺在实际工程应用中的参数设计,通过分析研究其工艺流程及有机物降解机理,在借鉴和参考污水处理领域数学模型相关研究的基础上,构建了有机物降解数学模型。结果表明,有机物在不同条件下进行降解时,水温、DO浓度等各种影响因素互相干扰,降解机理复杂。基于人工神经网络的反向传播算法,以COD的初始浓度、DO、温度为输入层,以有机物降解速率常数为输出层,建立确定有机物降解速率常数的神经网络模型,并仿真多因素同时变化时降解速率常数的动力学趋势。验证结果表明,建立的有机物降解模型能够对该工艺的污水处理效果即出水水质进行较好的模拟预测。     

水蕹菜对苏州重污染水体净化功能的研究

采用浮床无土栽培技术，在苏州重污染河道上种植水蕹菜以控制重污染水体水质。不仅进行了静态试验，而且在重污染河道苗家河上作了示范应用，效果显著。静态试验结果表明，在气温35℃、水温30℃以上的条件下，水蕹菜对苏州重污染水体中的CODMn、TN、NH4^＋-N、TP等的去除率分别为37．0％、92.9％、93．9％、94．3％；苗家河示范工程水域中水质有明最改善，透明度达90～130cm。由此证明水蕹菜是对苏州熏污染河道净化处理的优良生物材料之一。     

亲疏水性溶解性有机物对聚偏氟乙烯超滤膜污染行为

选用模拟亲疏水性有机物及实际二级处理水中的亲疏水性有机物,分别进行了聚偏氟乙烯(PVDF)超滤膜污染实验.并测定了不同污染物与膜及污染物间的作用力,分析亲/疏水性有机物对PVDF超滤膜的污染行为.结果表明,膜-污染物及污染物间相互作用力是控制膜污染行为的主导因素.亲水性有机物与PVDF超滤膜之间的相互亲和力较强,致使运行初期膜通量的大幅度下降,是PVDF膜的优势污染物.但是,针对实际污染物,运行后期,疏水性有机物之间较强的相互作用力使得其取代了亲水性有机物,成为膜的优势污染物.此外,模拟亲疏水性有机物的膜污染变化规律与实际亲疏水性有机物相似,表明使用模拟污染物可一定程度上预测实际废水中相应性能污染物的膜污染行为.     

曝气深度对河道底泥特性及水质的影响

采用室内模拟实验方法对受污河道底泥和上覆水进行研究,对比分析静置状态X0和不同曝气深度条件下(分别为水体曝气泥水界面上方10 cm,底泥曝气下方5和15 cm处,依次记为X+10、X-5和X-15)河道底泥特性及水质的影响情况。结果表明:底泥曝气较水体曝气而言,能促进水体DO更快恢复;停止曝气,DO浓度也会维持在较高的状态,有利于有机物和氨氮的进一步去除。在相同曝气量下,底泥曝气比水体曝气能更好地去除底泥中污染物,并减少再次释放,且底泥曝气深度越深,处理效果越好,至实验结束时,X-15组上覆水中COD、NH_4~+-N、TN及TP浓度分别为16.25、3.03、13.39及0.09 mg/L,去除率分别为69.73%、78.36%、45.98%及84.21%;停止曝气后,经曝气处理的底泥对磷的吸附容量显著增加,并且不会再向上覆水中释放污染物,避免引起水体的二次污染。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.