PM10 in the ambient air of Chandrapur coal mine and its comparison with other environments

This study compares the ambient air particulate matter (PM10) data of 15 different coal mine environments. For most of these mine environments, the monitoring was carried out by different researchers using respirable dust sampler (RDS) that separates PM10 by centrifugal inertial separation. At two sites — Padmapur and Ghugus (Chandrapur, Maharashtra, India) — mass inertial impaction-based sampler was used for PM10 monitoring. It is observed that the spatiotemporal average value of ambient air PM10 monitored using mass inertial impactor reports relatively higher values (240–372 μg/m³) compared to those monitored using RDS (<227 μg/m³). In order to realize the severity of mine area pollution, it is compared with PM10 values found in an urban area (Delhi, India). It is found that PM10 values in Delhi (using mass inertial impactor) are much higher (300–400 μg/m³) than those reported for the mine environment. The data seems to indicate that the mine environment is relatively cleaner than urban air and therefore raises doubt about the appropriateness of using either mass impactor or RDS for PM10 sampling.     

Seasonal Variations of PM10 and TSP in Residential and Industrial Sites in an Urban Area of Kolkata, India

The objective of the study is to investigate seasonal and spatial variations of PM₁₀ (particulate matter with aerodynamic diameter less than or equal to 10 μm) and TSP (total suspended particulate matter) of an Indian Metropolis with high pollution and population density from November 2003 to November 2004. Ambient concentration measurements of PM₁₀ and TSP were carried out at two monitoring sites of an urban region of Kolkata. Monitoring sites have been selected based on the dominant activities of the area. Meteorological parameters such as wind speed, wind direction, rainfall, temperature and relative humidity were also collected simultaneously during the sampling period from Indian Meteorological Department, Kolkata. The 24 h average concentrations of PM₁₀ and TSP were found in the range 68.2–280.6 μg/m³ and 139.3–580.3 μg/m³ for residential (Kasba) area, while 62.4–401.2 μg/m³ and 125.7–732.1 μg/m³ for industrial (Cossipore) area, respectively. Winter concentrations of particulate pollutants were higher than other seasons, irrespective of the monitoring sites. It indicates a longer residence time of particulates in the atmosphere during winter due to low winds and low mixing height. Spread of air pollution sources and non-uniform mixing conditions in an urban area often result in spatial variation of pollutant concentrations. The higher particulate pollution at industrial area may be attributed due to resuspension of road dust, soil dust, automobile traffic and nearby industrial emissions. Particle size analysis result shows that PM₁₀ is about 52% of TSP at residential area and 54% at industrial area.     

Particulate Matter Over A Seven Year Period in Urban and Rural Areas Within, Proximal and Far from Mining and Power Station Operations in Greece

Lignite mining operations and lignite-fired power stations result in major particulate pollution (fly ash and fugitive dust) problems in the areas surrounding these activities. The problem is more complicated, especially, for urban areas located not far from these activities, due to additional contribution from the urban pollution sources. Knowledge of the distribution of airborne particulate matter into size fraction has become an increasing area of focus when examining the effects of particulate pollution. On the other hand, airborne particle concentration measurements are useful in order to assess the air pollution levels based on national and international air quality standards. These measurements are also necessary for developing air pollutants control strategies or for evaluating the effectiveness of these strategies, especially, for long periods. In this study an attempt is made in order to investigate the particle size distribution of fly ash and fugitive dust in a heavy industrialized (mining and power stations operations) area with complex terrain in the northwestern part of Greece. Parallel total suspended particulates (TSP) and particulate matter with an aerodynamic diameter less than 10 μm (PM10) concentrations are analyzed. These measurements gathered from thirteen monitoring stations located in the greater area of interest. Spatial, temporal variation and trend are analyzed over the last seven years. Furthermore, the geographical variation of PM10 – TSP correlation and PM10/TSP ratio are investigated and compared to those in the literature. The analysis has indicated that a complex system of sources and meteorological conditions modulate the particulate pollution of the examined area.     

Monitoring of ambient particles and heavy metals in a residential area of Seoul, Korea

In this study, ambient TSP, PM10, and PM2.5 in a residential area located in the northern part of Seoul were monitored every other month for 1 year from April 2005 to February 2006. The monthly average levels of TSP, PM10, and PM2.5 had ranges of 71∼158, 40∼106, and 28∼43 μg/m³, respectively. TSP and PM10 showed highest concentration in April; this seems to be due to Asian dust from China and/or Mongolia. However, the fine particle of PM2.5 showed a relatively constant level during the monitoring period. Heavy metals in PM 10 and PM2.5, such as Cr, As, Cd, Mn, Zn and Pb, were also analysed during the same period. The monthly average concentrations of heavy metal in PM2.5 were Cr:1.9∼22.7 ng/m³; As:0.9∼2.5 ng/m³; Cd: 0.6∼7 ng/m³; Mn:6.1∼22.6 ng/m³; Zn: 38.9∼204.8 ng/m³, and Pb: 21.6∼201.1 ng/m³. For the health risk assessment of heavy metals in ambient particles, excess cancer risks were calculated using IRIS unit risk. As a result, the excess cancer risks of chromium, cadmium, and arsenic were shown to be more than one per million based on the annual concentration of heavy metals, and chromium showed the highest excess cancer risk in ambient particles in Seoul.     

Receptor model-based source apportionment of particulate pollution in Hyderabad, India

Air quality in Hyderabad, India, often exceeds the national ambient air quality standards, especially for particulate matter (PM), which, in 2010, averaged 82.2?±?24.6, 96.2?±?12.1, and 64.3?±?21.2 μg/m³ of PM₁₀, at commercial, industrial, and residential monitoring stations, respectively, exceeding the national ambient standard of 60 μg/m³. In 2005, following an ordinance passed by the Supreme Court of India, a source apportionment study was conducted to quantify source contributions to PM pollution in Hyderabad, using the chemical mass balance (version 8.2) receptor model for 180 ambient samples collected at three stations for PM₁₀ and PM_2.5 size fractions for three seasons. The receptor modeling results indicated that the PM₁₀ pollution is dominated by the direct vehicular exhaust and road dust (more than 60 %). PM_2.5 with higher propensity to enter the human respiratory tracks, has mixed sources of vehicle exhaust, industrial coal combustion, garbage burning, and secondary PM. In order to improve the air quality in the city, these findings demonstrate the need to control emissions from all known sources and particularly focus on the low-hanging fruits like road dust and waste burning, while the technological and institutional advancements in the transport and industrial sectors are bound to enhance efficiencies. Andhra Pradesh Pollution Control Board utilized these results to prepare an air pollution control action plan for the city.     

Investigation into presence of atmospheric particulate matter in Marikana, mining area in Rustenburg Town, South Africa

An investigation to find out presence of particulate matter in Marikana, a mining area in Rustenburg town, South Africa, was carried out in the months of August and November of 2008. Samples were collected for measurements of particulate matter (PM) of particle diameters of PM10, PM2.5, and PM1. After gravimetric analysis of daily measurements, it was found that PM10 concentration values ranged between 3 and 9 ??g/m³, PM2.5 concentration values ranged between 16 and 26 ??g/m³, and PM1 concentration values ranged between 14 and 18 ??g/m³ for the month of August 2008. For the month of November, it was found that PM10 concentration values ranged between 2 and 8 ??g/m³, PM2.5 concentration values ranged between 0 and 5 ??g/m³, and PM1 concentration values ranged between 4 and 15 ??g/m³. This study was undertaken as preliminary work having in mind that mining activities could be emitting high levels of particulate matter in the atmosphere which might be degrading the quality of the air. It was observed, however, that the daily particulate matter especially of PM10 emitted were quite low when compared to laid down International Air Quality Standards. The standards did not give guidelines for particulate matter of diameter 2.5 ??m. It was concluded that particulate matter came from three major sources: platinum mining, domestic biomass burning, and traffic emissions due to fuel burning.     

Impact of Diwali celebrations on urban air and noise quality in Delhi City,India

A study was conducted in the residential areas of Delhi, India, to assess the variation in ambient air quality and ambient noise levels during pre-Diwali month (DM), Diwali day (DD) and post-Diwali month during the period 2006 to 2008. The use of fireworks during DD showed 1.3 to 4.0 times increase in concentration of respirable particulate matter (PM₁₀) and 1.6 to 2.5 times increase in concentration of total suspended particulate matter (TSP) than the concentration during DM. There was a significant increase in sulfur dioxide (SO₂) concentration but the concentration of nitrogen dioxide (NO₂) did not show any considerable variation. Ambient noise level were 1.2 to 1.3 times higher than normal day. The study also showed a strong correlation between PM₁₀ and TSP (R ² ≥ 0.9) and SO₂ and NO₂ (R ² ≥ 0.9) on DD. The correlation between noise level and gaseous pollutant were moderate (R ² ≥ 0.5). The average concentration of the pollutants during DD was found higher in 2007 which could be due to adverse meteorological conditions. The statistical interpretation of data indicated that the celebration of Diwali festival affects the ambient air and noise quality. The study would provide public awareness about the health risks associated with the celebrations of Diwali festival so as to take proper precautions.     

Suspended Particulate Matter Distribution in Rural-Industrial Satna and in Urban-Industrial South Delhi

An air quality sampling program was designed and implemented to collect the baseline concentrations of respirable suspended particulates (RSP = PM₁₀), non-respirable suspended particulates (NRSP) and fine suspended particulates (FSP = PM_2.5). Over a three-week period, a 24-h average concentrations were calculated from the samples collected at an industrial site in Southern Delhi and compared to datasets collected in Satna by Envirotech Limited, Okhla, Delhi in order to establish the characteristic difference in emission patterns. PM_2.5, PM₁₀, and total suspended particulates (TSP) concentrations at Satna were 20.5 ± 6.0, 102.1 ± 41.1, and 387.6 ± 222.4 μg m⁻³ and at Delhi were 126.7 ± 28.6, 268.6 ± 39.1, and 687.7 ± 117.4 μg m⁻³. Values at Delhi were well above the standard limit for 24-h PM_2.5 United States National Ambient Air Quality Standards (USNAAQS; 65 μg m⁻³), while values at Satna were under the standard limit. Results were compared with various worldwide studies. These comparisons suggest an immediate need for the promulgation of new PM_2.5 standards. The position of PM₁₀ in Delhi is drastic and needs an immediate attention. PM₁₀ levels at Delhi were also well above the standard limit for 24-h PM₁₀ National Ambient Air Quality Standards (NAAQS; 150 μg m⁻³), while levels at Satna remained under the standard limit. PM_2.5/PM₁₀ values were also calculated to determine PM_2.5 contribution. At Satna, PM_2.5 contribution to PM₁₀ was only 20% compared to 47% in Delhi. TSP values at Delhi were well above, while TSP values at Satna were under, the standard limit for 24-h TSP NAAQS (500 μg m⁻³). At Satna, the PM₁₀ contribution to TSP was only 26% compared to 39% in Delhi. The correlation between PM₁₀, PM_2.5, and TSP were also calculated in order to gain an insight to their sources. Both in Satna and in Delhi, none of the sources was dominant a varied pattern of emissions was obtained, showing the presence of heterogeneous emission density and that nonrespirable suspended particulate (NRSP) formed the greatest part of the particulate load.     

Evaluation of the Impact of Long-range Transport and Aerosol Concentration Temporal Variations at the Eastern Coast of the Baltic Sea

Ambient particles vary greatly in their ability to affect visibility, climate and human health. The fine fraction of aerosol is responsible for greater and wider effects on human health; thus, investigation of this fraction is very important. Continuous measurements of PM2.5 (particulate matter below 2.5 μm in size) concentrations at the Preila monitoring station started in 2003. During a period of 2 years, the episodes of high daily and semi-hourly concentrations of PM2.5 were measured. These episodes did not depend on the season or time of day. The substantial role of long-range transport of pollutants to these increases in concentration was shown using chemical and statistical analysis. It was found that most of the severe episodes occurred when air masses came from a specific site besides it was established that air masses of different origin were characterized by different mixing layer depth. Lower mixing depth was observed in air masses characterized by higher observed concentrations at the measuring site and vice versa. PM2.5 concentrations showed diurnal and seasonal variations whose pattern reflected the regional origin of the aerosol. The regional pollution level was evaluated by the statistical analysis of PM2.5 concentrations. The background annual average of PM2.5 mass concentration for the eastern coast of the Baltic Sea was 15.1 ± 0.8 μg m⁻³.     

Air Quality Status of an Open Pit Mining Area in India

This investigation presents the assessment of ambient air quality carried out at an open pit coal mining area in Orissa state of India. The 24-h average concentrations of suspended particulate matter (SPM), respirable particulate matter (RPM, particles of less than 10 m aerodynamic diameter), sulphur dioxide (SO₂) and oxides of nitrogen (NO_x) were determined at regular interval throughout one year at 13 monitoring stations in residential area and four stations in mining/industrial area. During the study period, the 24-h and annual average SPM and RPM concentrations exceeded the respective standards set in the Indian ambient air quality standard (NAAQS) protocol in most of the residential and industrial areas. However, the 24-h and annual average concentrations of SO₂ and NO_x were well within the prescribed limit of the NAAQS in both residential and industrial areas. A management strategy is formulated for effective control of particulate matter at source and other mitigative measures are recommended including implementation of green belts around the sensitive areas.     

Air quality and deposition of trace elements in Didouche Mourad, Algeria

Total suspended particulate matter and deposition fluxes of particles were investigated in the town of Didouche Mourad which is located 13 km north of Constantine. Samples of air particulate matter were collected at one site located in the heart of the town and situated 3 km north of a cement plant. Samples were collected from 2 November 2002 to 28 April 2003 every 3 days using a high volume air sampler. Sampling intervals were 24 h in all cases. During the same period, samples of dust fallout were collected at the same site. Samples were collected at 30-day intervals. Lead, chromium, manganese, nickel, copper, cobalt and cadmium deposition fluxes were measured and both the soluble and insoluble fractions were determined. Furthermore, the information gathered by this study was correlated with the corresponding hourly weather data provided by a weather station installed at the study station. The possible sources for dust and trace metals were analyzed by comparing average contributions of wind aspects to the concentrations and depositions of mass and chemical species with the average frequencies of wind direction. The mean concentration was 300 μg/m³. The average dust deposition rate through the period of study was 221 mg/(m².day). Results indicate that anthropogenic sources contribute greatly to trace elements. An exposure assessment to the heavy metals taking into account the inhalation route and soil dust ingestion was carried out and allowed direct comparison of trace metal intakes via these routes.     

Characterization and Identification of the Sources of Chromium, Zinc, Lead, Cadmium, Nickel, Manganese and Iron in Pm10 Particulates at the Two Sites of Kolkata, India

Monitoring of ambient PM₁₀ (particulate matter which passes through a size selective impactor inlet with a 50% efficiency cut-off at 10 μm aerodynamic diameter) has been done at residential (Kasba) and industrial (Cossipore) sites of an urban region of Kolkata during November 2003 to November 2004. These sites were selected depending on the dominant anthropogenic activities. Metal constituents of atmospheric PM₁₀ deposited on glass fibre filter paper were estimated using Inductively Coupled Plasma Atomic Emission Spectrometer (ICP-AES). Chromium (Cr), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), manganese (Mn) and iron (Fe) are the seven toxic trace metals quantified from the measured PM₁₀ concentrations. The 24 h average concentrations of Cr, Zn, Pb, Cd, Ni, Mn and Fe from ninety PM₁₀ particulate samples of Kolkata were found to be 6.9, 506.1, 79.1, 3.3, 7.4, 2.4 and 103.6 ng/m³, respectively. The 24 h average PM₁₀ concentration exceeded national ambient air quality standard (NAAQS) as specified by central pollution control board, India at both residential (Kasba) and industrial (Cossipore) areas with mean concentration of 140.1 and 196.6 μg/m³, respectively. A simultaneous meteorology study was performed to assess the influence of air masses by wind speed, wind direction, rainfall, relative humidity and temperature. The measured toxic trace metals generally showed inverse relationship with wind speed, relative humidity and temperature. Factor analysis, a receptor modeling technique has been used for identification of the possible sources contributing to the PM₁₀. Varimax rotated factor analysis identified four possible sources of measured trace metals comprising solid waste dumping, vehicular traffic with the influence of road dust, road dust and soil dust at residential site (Kasba), while vehicular traffic with the influence of soil dust, road dust, galvanizing and electroplating industry, and tanning industry at industrial site (Cossipore).     

Particulate emission inventory and trends in ambient particulate matter concentrations in the Czech Republic between 1993 and 1999

Trends in total suspended particulates (TSP) emissioninventories were compared with ambient TSP concentrationsduring the period of 1993-1999 in the Czech Republic. TheTSP annual emission decreased within the period of observationfrom 441 300 to 67 000 of metric tonnes (by 85%). During thesame period a less pronounced downward trend from80.3 g m^-3 to 31.5g m^-3 (decrease by 61%)was noted also for the ambient TSP annual average. Differencebetween the two air quality indicators seems to indicate thatchanges in TSP emission inventories from year to year arebeing to some extent overestimated. Monthly ambientparticulate concentrations did not respond to overall drop inemissions proportionately but were closely associated withmonthly mean temperatures. While in the winter the correlationbetween ambient TSP and temperature was negative, in summerthe correlation between the two variables was positive. Inspring and autumn there was no clear correlation betweentemperature and ambient particulate pollution. The improvementof air quality in the Czech Republic since the economical andpolitical transformation in 1990s is substantial whendemonstrated by emission figures, however, true state ofparticulate pollution expressed by ambient levels requiresfurther attention.     

Monitoring and Assessment of Exhaust Emission in Bangkok Street Air

Measurement of the exhaust emission from gasoline-powered motor vehicles in Bangkok were performed on chassis dynamometer. A fleet of 10 vehicles of different model, years and manufacturers were selected to measure the air pollutants in the exhaust effluent. The study revealed that the carbon monoxide and hydrocarbon emissions averaged 32.3–64.2 and 1.82–2.98 g km^–1, respectively, for 1990–1992 cars and decreased to 17.8–40.71 and 0.75–1.88 g km^–1, respectively, for 1994–1995 cars. A monitoring program for air pollutant concentrations in ambient air was also conducted to evaluate the air pollution problems in Bangkok arising from vehicle exhaust emission. Four air sampling stations were strategically established to cover the Bangkok Metropolitan Region (BMR). Composite air samples in this study area were collected during the day/night times and weekday/weekend. The average concentrations of suspended particulate matter, carbon monoxide, and nitrogen dioxide in Bangkok street air were found to be 0.65 mg/m³ (24 hr ave.), 19.02 mg/m³ (8 hr ave.) and 0.021 mg/m³ (1 hr ave.), respectively. The average concentrations of benzene and toluene in the ambient air of the study area were found to be 15.07–50.20 and 25.76–130.95 g/mf³, respectively, for 8 hr average. These results indicated that there was a significant increase in air pollutant emissions with increasing car mileage and model year. Subsequent analysis of data showed that there were only 20% of the test vehicles complied to approved emission standard. The finding also revealed that there was a correlation between the average air pollutant concentrations with average traffic speed in each traffic zone of the Bangkok Metropolitan Region (BMR).     

Chemical Composition and Sources of PM10 and PM2.5 Aerosols in Guangzhou, China

Aerosol samples of PM10 and PM2.5 are collected in summertime at four monitoring sites in Guangzhou, China. The concentrations of organic and elemental carbons (OC/EC), inorganic ions, and elements in PM10 and PM2.5 are also quantified. Our study aims to: (1) characterize the particulate concentrations and associated chemical species in urban atmosphere (2) identify the potential sources and estimate their apportionment. The results show that average concentration of PM2.5 (97.54 μg m⁻³) in Guangzhou significantly exceeds the National Ambient Air Quality Standard (NAAQS) 24-h average of 65 μg m⁻³. OC, EC, Sulfate, ammonium, K, V, Ni, Cu, Zn, Pb, As, Cd and Se are mainly in PM2.5 fraction of particles, while chloride, nitrate, Na, Mg, Al, Fe, Ca, Ti and Mn are mainly in PM2.5-10 fraction. The major components such as sulfate, OC and EC account for about 70–90% of the particulate mass. Enrichment factors (EF) for elements are calculated to indicate that elements of anthropogenic origins (Zn, Pb, As, Se, V, Ni, Cu and Cd) are highly enriched with respect to crustal composition (Al, Fe, Ca, Ti and Mn). Ambient and source data are used in the multi-variable linearly regression analysis for source identification and apportionment, indicating that major sources and their apportionments of ambient particulate aerosols in Guangzhou are vehicle exhaust by 38.4% and coal combustion by 26.0%, respetively.     

Evaluation of levels, sources and distribution of toxic elements in PM10 in a suburban industrial region, Rio de Janeiro, Brazil

The Oswaldo Cruz Foundation Campus (FIOCRUZ), in a suburban region of the city of Rio de Janeiro, was selected as a case study to assess the pollution released from vehicle and industrial facilities in Basin III, the most polluted area of the city. Concentrations of particulate matter (PM10) and trace metals in airborne particles were determined in an intensive field campaign. The samplings were performed every six days for 24 h periods, using a PM10 high volume sampler, from September 2004 to August 2005. PM10 mass concentrations were determined gravimetrically and the metals by ICP-OES. For PM10, the arithmetic mean for the period is 169 ± 42 μg m⁻³ which is 3.4 times the national recommended standard of 50 μg m⁻³. Additionally, 51% of the samplings exceeded the recommended 24 h limit of 150 μg m⁻³. Ca, Mg, Fe, Zn and Al were the metals that presented the higher concentrations. The correlation matrix gave two main clusters and three significant principal components (PC). Both PC1 and PC2 are associated to crustal, vehicular and industrial emissions while PC3 is mainly associated to geological material. Enrichment factors for Zn, Cu, Cd and Pb indicate that for these elements, anthropic sources prevail over natural inputs. PM10 levels showed a good correlation with hospital admissions for respiratory diseases in children and elderly people.     

北方沙尘对江苏环境空气中可吸入颗粒物浓度的影响

利用卫星遥感数据、气象观测资料和江苏省环境空气自动站的可吸入颗粒物的监测数据,对春季中国北方的沙尘暴过程对江苏环境空气中可吸入颗粒物浓度的影响分析发现,沙尘暴所含的沙尘粒子在冷空气的引导下可能进入江苏,对环境空气中可吸入颗粒物浓度将会产生较大的影响;北方沙尘暴所携带的沙尘粒子是春季江苏空气污染的重要来源之一,是预报空气质量异常偏高的重要依据之一。     

Characterization of atmospheric dust at Gurushikar,Mt. Abu,Rajasthan

The nature of atmospheric aerosols at Gurushikar, Mt. Abu, Rajasthan where a gamma ray telescope is to be installed, was investigated. Air particulate samples collected on filters were used to estimate the total suspended particulate matter (TSPM) and its elemental composition. The TSPM varied from 31 to 103 g/m³ during January to March 1994. The heighest loads were observed during the months of May and June (80–100 g/m³) and lowest during October (20–60 g/m³). The dust was also examined for size, shape and nature of the mineral matter. The particle sizes varied from 100 m to 5 m. The course particles (>50 m) are irregular shaped quartz grains. Some of the medium size (=50 m) particles were spherical and were highly conducting. These particles were rich in iron content. Correlation coefficients among various elements in the dust showed that it is made up of mainly two components-wind blown ground dust and particulate arising out of wood and coal burning.     

鞍山市环境空气颗粒物中重金属元素分布特征

研究了鞍山市环境空气中可吸入颗粒物(PM10和PM2.5)中重金属元素分布特征,结果表明鞍山市环境空气可吸入颗粒物中Zn、Pb、Al、Cu四种金属总和所占21种元素比例近85%。重金属元素在不同粒径颗粒物中的浓度水平有明显差别,更易富集在细颗粒物PM2.5上。     

Air Pollution Concentrations of PM2.5, PM10 and NO2 at Ambient and Kerbsite and Their Correlation in Metro City – Mumbai

Ambient concentrations of PM_2.5 and PM₁₀ are of concern with respect to effects on human health and environment. Increased levels of mortality and morbidity have been associated with respirable particulate air pollution. In India, it is not yet mandatory to monitor PM_2.5 levels therefore very limited information is available on PM_2.5 levels. To understand the fine particle pollution and also correlate with PM₁₀ which are monitored regularly in compliance with ambient air quality standards. This study was carried out to monitor PM_2.5, PM₁₀, and NO₂ for about one year in a residential cum commercial area of Mumbai city with a view to understand their correlation. The average PM_2.5 concentration at ambient and Kerbsite was 43 and 69 μg/m³. The correlation coefficients between PM_2.5 and PM₁₀ at ambient and Kerbsite were 0.83 and 0.85 respectively thus indicating that most of the PM_2.5 and PM₁₀ are from similar sources. TSP, PM₁₀ levels exceeded Central Pollution Control Board(CPCB) standard during winter season. PM_2.5 levels also exceeded 24 hourly average USEPA standard during winter season indicating unhealthy air quality.