Characteristics of Hazardous Airborne Dust Around an Indian Surface Coal Mining Area

Surface coal mining creates more air pollution problems with respect to dust than underground mining . An investigation was conducted to evaluate the characteristics of the airborne dust created by surface coal mining in the Jharia Coalfield. Work zone air quality monitoring was conducted at six locations, and ambient air quality monitoring was conducted at five locations, for a period of 1 year. Total suspended particulate matter (TSP) concentration was found to be as high as 3,723 μg/m³, respirable particulate matter (PM10) 780 μg/m³, and benzene soluble matter was up to 32% in TSP in work zone air. In ambient air, the average maximum level of TSP was 837 μg/m³, PM10 170 μg/m³ and benzene soluble matter was up to 30%. Particle size analysis of TSP revealed that they were more respirable in nature and the median diameter was around 20 μm. Work zone air was found to have higher levels of TSP, PM10 and benzene soluble materials than ambient air. Variations in weight percentages for different size particles are discussed on the basis of mining activities. Anionic concentration in TSP was also determined. This paper concludes that more stringent air quality standards should be adopted for coal mining areas and due consideration should be given on particle size distribution of the air-borne dust while designing control equipment.     

乌鲁木齐采暖期TSP、PM10、PM5、PM2.5中重金属污染水平评价

采用石墨炉原子吸收分光光度法、双道原子荧光光谱法研究乌鲁木齐市采暖期前期与后期不同粒径大气颗粒物(TSP、PM_(10)、PM_5、PM_(2.5))中Hg、As、Zn、Pb、Ni等5种重金属元素的质量浓度,并对重金属污染水平进行评价。Hg质量浓度为0.3~5.7 ng/m3;As质量浓度为15.3~122.5 ng/m~3;Zn质量浓度为298.0~1 686.5 ng/m~3;Pb质量浓度为0.5~88.8 ng/m~3;Ni质量浓度为10.4~25.5 ng/m~3。Igeo计算得出采暖期后期的TSP、PM_(10)、PM_5、PM_(2.5)中各重金属Igeo值均高于采暖期前期,其中Hg元素为严重污染;富集因子分析得出Hg、Zn元素的EFi值大于10,说明这些元素是人为源贡献。通过研究乌鲁木齐市不同时期、不同粒径大气颗粒物中各种重金属污染状况,为乌鲁木齐大气污染治理提供科学支持。     

Chemical Composition and Sources of PM10 and PM2.5 Aerosols in Guangzhou, China

Aerosol samples of PM10 and PM2.5 are collected in summertime at four monitoring sites in Guangzhou, China. The concentrations of organic and elemental carbons (OC/EC), inorganic ions, and elements in PM10 and PM2.5 are also quantified. Our study aims to: (1) characterize the particulate concentrations and associated chemical species in urban atmosphere (2) identify the potential sources and estimate their apportionment. The results show that average concentration of PM2.5 (97.54 μg m⁻³) in Guangzhou significantly exceeds the National Ambient Air Quality Standard (NAAQS) 24-h average of 65 μg m⁻³. OC, EC, Sulfate, ammonium, K, V, Ni, Cu, Zn, Pb, As, Cd and Se are mainly in PM2.5 fraction of particles, while chloride, nitrate, Na, Mg, Al, Fe, Ca, Ti and Mn are mainly in PM2.5-10 fraction. The major components such as sulfate, OC and EC account for about 70–90% of the particulate mass. Enrichment factors (EF) for elements are calculated to indicate that elements of anthropogenic origins (Zn, Pb, As, Se, V, Ni, Cu and Cd) are highly enriched with respect to crustal composition (Al, Fe, Ca, Ti and Mn). Ambient and source data are used in the multi-variable linearly regression analysis for source identification and apportionment, indicating that major sources and their apportionments of ambient particulate aerosols in Guangzhou are vehicle exhaust by 38.4% and coal combustion by 26.0%, respetively.     

Evaluation of levels, sources and distribution of toxic elements in PM10 in a suburban industrial region, Rio de Janeiro, Brazil

The Oswaldo Cruz Foundation Campus (FIOCRUZ), in a suburban region of the city of Rio de Janeiro, was selected as a case study to assess the pollution released from vehicle and industrial facilities in Basin III, the most polluted area of the city. Concentrations of particulate matter (PM10) and trace metals in airborne particles were determined in an intensive field campaign. The samplings were performed every six days for 24 h periods, using a PM10 high volume sampler, from September 2004 to August 2005. PM10 mass concentrations were determined gravimetrically and the metals by ICP-OES. For PM10, the arithmetic mean for the period is 169 ± 42 μg m⁻³ which is 3.4 times the national recommended standard of 50 μg m⁻³. Additionally, 51% of the samplings exceeded the recommended 24 h limit of 150 μg m⁻³. Ca, Mg, Fe, Zn and Al were the metals that presented the higher concentrations. The correlation matrix gave two main clusters and three significant principal components (PC). Both PC1 and PC2 are associated to crustal, vehicular and industrial emissions while PC3 is mainly associated to geological material. Enrichment factors for Zn, Cu, Cd and Pb indicate that for these elements, anthropic sources prevail over natural inputs. PM10 levels showed a good correlation with hospital admissions for respiratory diseases in children and elderly people.     

Polycyclic aromatic hydrocarbons in bulk PM2.5 and size-segregated aerosol particle samples measured in an urban environment

To analyze polycyclic aromatic hydrocarbons (PAHs) at an urban site in Seoul, South Korea, 24-hr ambient air PM_2.5 samples were collected during five intensive sampling periods between November 1998 and December 1999. To determine the PAH size distribution, 3-day size-segregated aerosol samples were also collected in December 1999. Concentrations of the 16 PAHs in the PM_2.5 particles ranged from 3.9 to 119.9 ng m⁻³ with a mean of 24.3 ng m⁻³.An exceptionally high concentration of PAHs(∼120 ng m⁻³) observed during a haze event in December 1999 was likely influenced more by diesel vehicle exhaust than by gasoline exhaust, as well as air stagnation, as evidenced by the low carbon monoxide/elemental carbon (CO/EC) ratio of 205 found in this study and results reported by previous studies. The total PAHs associated with the size-segregated particles showed unimodal distributions. Compared to the unimodal size distributions of PAHs with modal peaks at < 0.12 μm measured in highway tunnels in Los Angeles (Venkataraman and Friedlander, 1994), four- to six-ring PAHs in our study had unimodal size distributions, peaking at the larger size range of 0.28–0.53 μm, suggesting the coagulation of freshly emitted ultrafine particles during transport to the sampling site. Further, the fraction of PAHs associated with coarse particles(> 1.8 μm) increased as the molecular weight of the PAHs decreased due to volatilization of fine particles followed by condensation onto coarse particles.     

Characterization of PM10 and PM2.5 and associated heavy metals at the crossroads and urban background site in Zabrze, Upper Silesia, Poland, during the smog episodes

The concentrations of seven heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, and Pb) associated with PM10 and PM2.5 at the crossroads and the background sites have been studied in Zabrze, Poland, during smog episodes. Although the background level was unusually elevated due to both high particulate emission from the industrial and municipal sources and smog favorable meteorological conditions, significant increase of the concentration of PM2.5 and PM10 as well as associated heavy metals in the roadside air compared to the urban background has been documented. The average daily difference between the roadside and corresponding urban background aerosol concentration was equal to 39.5 μg m^???3 for PM10 and 41.2 μg m^???3 for PM2.5. The highest levels of the studied metals in Zabrze appeared for iron carried by PM10 particles: 1,706 (background) and 28,557 ng m^???3 (crossroads). The lowest concentration level (in PM10) has been found for cadmium: 7 and 77 ng m^???3 in the background and crossroads site, respectively. Also the concentrations of heavy metals carried by the fine particles (PM2.5) were very high in Zabrze during the smog episodes. Concentrations of all studied metals associated with PM10 increased at the roadside compared to the background about ten times (one order) while metals contained in PM2.5 showed two to three times elevated concentrations (except Fe—five times and Cr—no increase).     

Atmospheric PAH concentrations in fine and coarse particles

Measurements of the urban air concentrations of PAHsassociated with PM2.5-fine and PM10-coarse particles inChicago on the campus of IIT were achieved using a UniversalAir Sampler. Short sampling time (12 hr) and high flowrates were used to measure the PAH concentrations in fineand coarse particles. Measured ambient concentrations ofPAHs were classified based on wind direction and backtrajectory calculations as Land and Lake samples.Differences in ambient concentrations of PAHs were observedbetween Land and Lake samples. Fine particle concentrationsvaried from 9.5 to 25.7 ng m^-3 and averaged18.2 ng m^-3 for the Land samples, while they ranged from4.2 to 31.5 ng m^-3 and averaged 13.4 ng m^-3 for the Lake samples. The measured PAH concentrationsin coarse particles varied from 6.2 to 22.1 ng m^-3 and averaged 12.9 ng m^-3 for the Land samples, andthey ranged from 2.4 to 13.0 ng m^-3 with an average value of 7.3 ng m^-3 for the Lake samples. The fine/coarse ratio of each individual PAH compound varied between1.3 and 2.7 for the Land samples; it varied between 1.6 and 4.2 for the Lake samples. There was an increase in the fine/coarse ratio of PAH as molecular weight of the compound increases for both Land and Lake samples.     

Suspended Particulate Matter Distribution in Rural-Industrial Satna and in Urban-Industrial South Delhi

An air quality sampling program was designed and implemented to collect the baseline concentrations of respirable suspended particulates (RSP = PM₁₀), non-respirable suspended particulates (NRSP) and fine suspended particulates (FSP = PM_2.5). Over a three-week period, a 24-h average concentrations were calculated from the samples collected at an industrial site in Southern Delhi and compared to datasets collected in Satna by Envirotech Limited, Okhla, Delhi in order to establish the characteristic difference in emission patterns. PM_2.5, PM₁₀, and total suspended particulates (TSP) concentrations at Satna were 20.5 ± 6.0, 102.1 ± 41.1, and 387.6 ± 222.4 μg m⁻³ and at Delhi were 126.7 ± 28.6, 268.6 ± 39.1, and 687.7 ± 117.4 μg m⁻³. Values at Delhi were well above the standard limit for 24-h PM_2.5 United States National Ambient Air Quality Standards (USNAAQS; 65 μg m⁻³), while values at Satna were under the standard limit. Results were compared with various worldwide studies. These comparisons suggest an immediate need for the promulgation of new PM_2.5 standards. The position of PM₁₀ in Delhi is drastic and needs an immediate attention. PM₁₀ levels at Delhi were also well above the standard limit for 24-h PM₁₀ National Ambient Air Quality Standards (NAAQS; 150 μg m⁻³), while levels at Satna remained under the standard limit. PM_2.5/PM₁₀ values were also calculated to determine PM_2.5 contribution. At Satna, PM_2.5 contribution to PM₁₀ was only 20% compared to 47% in Delhi. TSP values at Delhi were well above, while TSP values at Satna were under, the standard limit for 24-h TSP NAAQS (500 μg m⁻³). At Satna, the PM₁₀ contribution to TSP was only 26% compared to 39% in Delhi. The correlation between PM₁₀, PM_2.5, and TSP were also calculated in order to gain an insight to their sources. Both in Satna and in Delhi, none of the sources was dominant a varied pattern of emissions was obtained, showing the presence of heterogeneous emission density and that nonrespirable suspended particulate (NRSP) formed the greatest part of the particulate load.     

Indoor and outdoor PM mass and number concentrations at schools in the Athens area

Simultaneous indoor and outdoor PM₁₀ and PM_2.5 concentration measurements were conducted in seven primary schools in the Athens area. Both gravimetric samplers and continuous monitors were used. Filters were subsequently analyzed for anion species. Moreover ultrafine particles number concentration was monitored continuously indoors and outdoors. Mean 8-hr PM₁₀ concentration was measured equal to 229 ± 182 μg/m³ indoors and 166 ± 133 μg/m³ outdoors. The respective PM_2.5 concentrations were 82 ± 56 μg/m³ indoors and 56 ± 26 μg/m³ outdoors. Ultrafine particles 8-h mean number concentration was measured equal to 24,000 ± 17,900 particles/cm³ indoors and 32,000 ± 14,200 particles/cm³ outdoors. PM₁₀ outdoor concentrations exhibited a greater spatial variability than the corresponding PM_2.5 ones. I/O ratios were close or above 1.00 for PM₁₀ and PM_2.5 and smaller than 1.00 for ultrafine particles. Very high I/O ratios were observed when intense activities took place. The initial results of the chemical analysis showed that accounts for the 6.6 ± 3.5% of the PM₁₀ and for the 3.1 ± 1.4%.The corresponding results for PM_2.5 are 12.0 ± 7.7% for and 3.1 ± 1.9% for . PM_2.5 indoor concentrations were highly correlated with outdoor ones and the regression line had the largest slope and a very low intercept, indicative of no indoor sources of fine particulate . The results of the statistical analysis of indoor and outdoor concentration data support the use of as a proper surrogate for indoor PM of outdoor origin.     

Characterization, Source Identification and Apportionment of Selected Metals in TSP in an Urban Atmosphere

To understand the metal distribution characteristics in the atmosphere of urban Islamabad, total suspended particulate (TSP) samples were collected on daily 12 h basis, at Quaid-i-Azam University campus, using high volume sampler. The TSP samples were treated with HNO₃/HClO₄ based wet digestion method for the quantification of eight selected metals; Fe, Zn, Pb, Mn, Cr, Co, Ni and Cd by FAAS method. The monitoring period ran from June 2001 to January 2002, with a total of 194 samples collected on cellulose filters. Effects of different meteorological conditions such as temperature, relative humidity, wind speed and wind direction on selected metal levels were interpreted by means of multivariate statistical approach. Enhanced metal levels for Fe (930 ng/m³), Zn (542 ng/m³) and Pb (210 ng/m³) were found on the mean scale while Mn, Cr, Co and Ni emerged as minor contributors. Statistical correlation study was also conducted and a strong correlation was observed between Pb-Cr (r=0.611). The relative humidity showed some significant influence on atmospheric metal distribution while other meteorological parameters showed weak relationship with TSP metal levels. Regarding the origin of sources of heavy metals in TSP, the statistical procedure identified three source profiles; automobile emissions, industrial/metallurgical units, and natural soil dust. The metal levels were also compared with those reported for other parts of the world which showed that the metal levels in urban atmosphere of Islamabad are in exceedence than those of European industrial and urban sites while comparable with some Asian sites.     

Environmental Monitoring and Impact Assessment of a Solid Waste Disposal Site

The objective of this study is an attempt to conduct an environmentalmonitoring and impact assessment of the On-Nooch solid waste disposal sitein Bangkok, Thailand. Four water and five air sampling stations (2 upwindand 3 downwind directions) were established at the site. Grab water samplesfrom leachate treatment plant and Khlong Song Hong, a nearby stream, werecollected during the rainy and dry seasons. Analytical results of the wastewater discharged by the leachate treatment plant, during dry season showedchemical oxygen demand: 618 mg/l; biochemical oxygen demand: 80 mg/l;suspended solid: 101 mg/l; Total Kjeldahl Nitrogen: 283 mg/l, which werestill higher than standard limit for effluents in Thailand. During the dryseason, results also showed widespread heavy metal pollution from leachate(chromium: 1.03 mg/l; manganese: 1.07 mg/l; mercury: 0.025 mg/l) and werehigher than the allowable level of heavy metals for the Industrial EffluentStandard in Thailand. The direct discharge of untreated leachate into inlandwater will cause considerable water pollution in the study area. Compositeair samples in this study area were collected during the rainy and dryseasons and were analyzed for methane (CH₄), carbon dioxide(CO₂), carbon monoxide (CO), sulphur dioxide(SO₂), nitrogen dioxide (NO₂) andsuspended particulate matter (SPM). The average concentration of SPM rangedbetween 0.1–0.36 mg/m³ for 24-hour average, dependingupon the season. The level of CH₄ and CO₂ inthe ambient air of the study area were found to be 3.48–65.71mg/m³ and 886-1758 mg/m³ respectively which weremuch higher than the normal concentration of CH₄ andCO₂ in the air (CH₄: 2.41 mg/m³;CO₂: 585 mg/m³). Hence, adverse health andenvironmental effects could be expected from water and air pollution.     

Environmental risk assessment of heavy metal extractability in a biosludge from the biological wastewater treatment plant of a pulp and paper mill

A five-stage sequential extraction procedure was used to fractionate heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Ni, Co, As, V and Ba) in a biosludge from the biological wastewater treatment plant of Stora Enso Oyj Veitsiluoto Mills at Kemi, Northern Finland, into the following fractions: (1) water-soluble fraction, (2) exchangeable fraction, (3) easily reduced fraction, (4) oxidizable fraction, and (5) residual fraction. The biosludge investigated in this study is a combination of sludge from the primary and secondary clarifiers at the biological wastewater treatment plant. Extraction stages (2)–(4) follow the protocol proposed by the Measurements and Testing Program (formerly BCR Programme) of the European Commission, which is based on acetic acid extraction (stage 2), hydroxylamine hydrochloride extraction (stage 3), and hydrogen peroxide digestion following the ammonium acetate extraction (stage 4). The residual fraction (stage 5) was based on digestion of the residue from stage 4 in a mixture of HF + HNO₃ + HCl. Although metals were extractable in all fractions, the highest concentrations of most of the metals occurred in the residual fraction. From the environmental point of view, it was notable that the total heavy metal concentrations in the biosludge did not exceed the maximal allowable heavy metal concentrations for sewage sludge used in agriculture, set on the basis of environmental protection of soil by European Union Directive 86/278/EEC, and by the Finnish legislation. The Ca (98.6 g kg⁻¹; dry weight) and Mg (2.2 g kg⁻¹; dry weight) concentrations in the biosludge were 62 and 11 times higher than the typical values of 1.6 and of 0.2 g kg⁻¹ (dry weight), respectively, in arable land in Central Finland. The biosludge had a slightly alkaline pH (∼8.30), a high loss-on-ignition value (∼78%) and a liming effect of 10.3% expressed as Ca equivalents (dry weight). This indicates its potential as a soil conditioner and improvement agent, as well as a pH buffer.     

Investigation into presence of atmospheric particulate matter in Marikana, mining area in Rustenburg Town, South Africa

An investigation to find out presence of particulate matter in Marikana, a mining area in Rustenburg town, South Africa, was carried out in the months of August and November of 2008. Samples were collected for measurements of particulate matter (PM) of particle diameters of PM10, PM2.5, and PM1. After gravimetric analysis of daily measurements, it was found that PM10 concentration values ranged between 3 and 9 ??g/m³, PM2.5 concentration values ranged between 16 and 26 ??g/m³, and PM1 concentration values ranged between 14 and 18 ??g/m³ for the month of August 2008. For the month of November, it was found that PM10 concentration values ranged between 2 and 8 ??g/m³, PM2.5 concentration values ranged between 0 and 5 ??g/m³, and PM1 concentration values ranged between 4 and 15 ??g/m³. This study was undertaken as preliminary work having in mind that mining activities could be emitting high levels of particulate matter in the atmosphere which might be degrading the quality of the air. It was observed, however, that the daily particulate matter especially of PM10 emitted were quite low when compared to laid down International Air Quality Standards. The standards did not give guidelines for particulate matter of diameter 2.5 ??m. It was concluded that particulate matter came from three major sources: platinum mining, domestic biomass burning, and traffic emissions due to fuel burning.     

Evaluation of the Impact of Long-range Transport and Aerosol Concentration Temporal Variations at the Eastern Coast of the Baltic Sea

Ambient particles vary greatly in their ability to affect visibility, climate and human health. The fine fraction of aerosol is responsible for greater and wider effects on human health; thus, investigation of this fraction is very important. Continuous measurements of PM2.5 (particulate matter below 2.5 μm in size) concentrations at the Preila monitoring station started in 2003. During a period of 2 years, the episodes of high daily and semi-hourly concentrations of PM2.5 were measured. These episodes did not depend on the season or time of day. The substantial role of long-range transport of pollutants to these increases in concentration was shown using chemical and statistical analysis. It was found that most of the severe episodes occurred when air masses came from a specific site besides it was established that air masses of different origin were characterized by different mixing layer depth. Lower mixing depth was observed in air masses characterized by higher observed concentrations at the measuring site and vice versa. PM2.5 concentrations showed diurnal and seasonal variations whose pattern reflected the regional origin of the aerosol. The regional pollution level was evaluated by the statistical analysis of PM2.5 concentrations. The background annual average of PM2.5 mass concentration for the eastern coast of the Baltic Sea was 15.1 ± 0.8 μg m⁻³.     

Seasonal Variations of PM10 and TSP in Residential and Industrial Sites in an Urban Area of Kolkata, India

The objective of the study is to investigate seasonal and spatial variations of PM₁₀ (particulate matter with aerodynamic diameter less than or equal to 10 μm) and TSP (total suspended particulate matter) of an Indian Metropolis with high pollution and population density from November 2003 to November 2004. Ambient concentration measurements of PM₁₀ and TSP were carried out at two monitoring sites of an urban region of Kolkata. Monitoring sites have been selected based on the dominant activities of the area. Meteorological parameters such as wind speed, wind direction, rainfall, temperature and relative humidity were also collected simultaneously during the sampling period from Indian Meteorological Department, Kolkata. The 24 h average concentrations of PM₁₀ and TSP were found in the range 68.2–280.6 μg/m³ and 139.3–580.3 μg/m³ for residential (Kasba) area, while 62.4–401.2 μg/m³ and 125.7–732.1 μg/m³ for industrial (Cossipore) area, respectively. Winter concentrations of particulate pollutants were higher than other seasons, irrespective of the monitoring sites. It indicates a longer residence time of particulates in the atmosphere during winter due to low winds and low mixing height. Spread of air pollution sources and non-uniform mixing conditions in an urban area often result in spatial variation of pollutant concentrations. The higher particulate pollution at industrial area may be attributed due to resuspension of road dust, soil dust, automobile traffic and nearby industrial emissions. Particle size analysis result shows that PM₁₀ is about 52% of TSP at residential area and 54% at industrial area.     

Particulate matter concentration levels during intense haze event in an urban environment

This study assessed concentration levels of particulate matter (PM) in the ambient environment of Ilorin metropolis, Nigeria, during haze episodes. Meteorological data (wind speed and direction, rainfall data, sunshine data, relative humidity and temperature) were obtained. Aerocet 531S particle counter (MetOne Instruments, USA) was used to measure four mass concentration ranges of PM (PM_1.0, PM_2.5, PM₁₀ and the total suspended particles (TSP)) in 10 locations taking into consideration land use patterns. Surfer® version 8 (Golden Software LLC, USA) was used to model the spatial variation of particulate matter concentration levels using kriging interpolation griding method. Human exposure assessment was done using the total respiratory deposition dose (TRDD) estimates and statutory limit breach (SLB) approaches. The appearance of dominating weak southern atmospheric wind flow was observed as wind speed ranged from 0 to 6.811 m/s while solar radiation periods ranged from 0.3 to 3.5 h/day. The relative humidity of the metropolis ranged between 28 and 57%, while daily temperature was 15 to 36 °C. Highest concentration levels of PM measured were 73.4, 562.7, 7066.3 and 9907.8 μg/m³ for PM_1.0, PM_2.5, PM₁₀ and TSP, respectively. Very strong negative correlations existed between the PM concentration levels and microclimatic parameters. Spatial variation of the concentration level as modelled using Surfer® version 8 indicated that particulate concentration level increases from south to north. Concentration levels of PM for the 24-h averaging period were generally above the 24-h threshold limit value set by the regulatory agencies for all the locations.     

北京市大气气态汞变化特征

采用Tekran 2537X大气汞分析仪在线测量北京市城区大气中气态元素汞(GEM,简称大气汞) 浓度,研究大气汞浓度随不同气象条件的变化特征。通过分析2016年10月—2017年9月大气汞监测数据发现,该监测点全年大气汞浓度为0.48～16.25 ng/m³,均值为(3.41±1.79)ng/m³。春季、夏季、秋季和冬季大气汞浓度均值依次为2.93 、2.95、4.27、3.37 ng/m³,其中,秋季大气汞浓度明显高于其他季节 。秋季大气汞浓度显著偏高可能由不利的大气扩散条件导致。大气汞夜间浓度显著高于白天浓度。同时,将大气汞与SO₂、CO及PM_2.5进行相关性分析,发现大气汞浓度变化趋势与SO₂、CO和PM_2.5呈显著正相关。结合风向和风速进行污染来源分析,得到该点位大气汞在西南和东北方向上受人为排放源影响较大。污染源类型分析表明,冬季大气汞与CO同源性强,主要来自本地供暖用煤。     

Monitoring of Criteria Air Pollutants in Bursa, Turkey

The concentrations of criteria air pollutants such as CO, NO_x (NO + NO₂), SO₂ and PM were measured in the period of May 2001 and April 2003 in the city of Bursa, Turkey. The average concentrations for this period were 1115±1600 μg/m³, 29±50 μg/m³, 51±24 μg/m³, 79±65 μg/m³, 40±35 μg/m³, 98±220 μg/m³, for CO, NO, NO₂, NO_x, SO₂ and PM, respectively. Temporal changes in concentrations were analyzed using meteorological factors. Correlations among pollutant concentrations and meteorological parameters showed weak relations nearly in all data. Lower concentrations were observed in the summer months while higher concentrations were measured in the winter months. The increase in winter concentrations was probably due to residential heating. Pollutants were associated with each other in order to have information about their origin. NO_x/SO₂ ratio was also examined to bring out the source origin contributing on air pollution (i.e., traffic or stationary).     

Air Pollution Concentrations of PM2.5, PM10 and NO2 at Ambient and Kerbsite and Their Correlation in Metro City – Mumbai

Ambient concentrations of PM_2.5 and PM₁₀ are of concern with respect to effects on human health and environment. Increased levels of mortality and morbidity have been associated with respirable particulate air pollution. In India, it is not yet mandatory to monitor PM_2.5 levels therefore very limited information is available on PM_2.5 levels. To understand the fine particle pollution and also correlate with PM₁₀ which are monitored regularly in compliance with ambient air quality standards. This study was carried out to monitor PM_2.5, PM₁₀, and NO₂ for about one year in a residential cum commercial area of Mumbai city with a view to understand their correlation. The average PM_2.5 concentration at ambient and Kerbsite was 43 and 69 μg/m³. The correlation coefficients between PM_2.5 and PM₁₀ at ambient and Kerbsite were 0.83 and 0.85 respectively thus indicating that most of the PM_2.5 and PM₁₀ are from similar sources. TSP, PM₁₀ levels exceeded Central Pollution Control Board(CPCB) standard during winter season. PM_2.5 levels also exceeded 24 hourly average USEPA standard during winter season indicating unhealthy air quality.     

Development of baseline (air quality) data in Pakistan

During 2003–2004, SUPARCO, the Pakistan Space and Upper Atmosphere Research Commission has conducted a year long baseline air quality study in country’s major urban areas (Karachi, Lahore, Quetta, Rawalpindi, Islamabad and Peshawar). The objective of this study was to establish baseline levels and behavior of airborne pollutants in urban centers with temporal and spatial parameters. This study reveals that the highest concentrations of CO were observed at Quetta (14 ppm) while other pollutants like SO₂ (52.5 ppb), NO _x (60.75 ppb) and O₃ (50 ppb) were higher at Lahore compared to other urban centers like Karachi, Peshawar etc. The maximum particulate (TSP) and PM10 levels were observed at Lahore (996 ug/m³ and 368 ug/m³ respectively), Quetta (778 ug/m³, 298 ug/m³) and in Karachi (410 ug/m³, 302 ug/m³). In all major cities the highest levels were recorded at major intersections and variations were directly correlated with traffic density. These pollutants showed highest levels in summer and spring while lowest were observed in winter and monsoon. A data bank has been generated for future planning and air pollution impact studies.