Leaching from MSWI bottom ash: evaluation of non-equilibrium in column percolation experiments

Impacts of non-equilibrium on results of percolation experiments on municipal solid waste incineration (MSWI) bottom ash were investigated. Three parallel column experiments were performed: two columns with undisturbed percolation and one column with two sets of 1-month-long flow interruptions applied at liquid-to-solid (L/S) ratios of L/S 2L/kg and 12L/kg, respectively. Concentrations of Na, K, Cl(-), Ca, Si, SO(4)(2-), Al, Cu, Ni, Mo, Ba, Pb, Zn, and dissolved organic carbon (DOC) were monitored throughout the entire leaching period; geochemical modeling was used to identify non-equilibrium-induced changes in the solubility control. Despite both physical and chemical non-equilibrium, the columns were found to provide adequate information for readily soluble compounds (i.e., Na, Cl(-), and K) and solubility-controlled elements (i.e., Ca, SO(4)(2-), Ba, Si, Al, Zn, and Pb). The leaching of Cu and Ni was shown to depend strongly on DOC leaching, which was likely affected by physical non-equilibrium during flow interruptions. Consequently, the leaching of Cu and Ni in the undisturbed columns was shown to be by about one order of magnitude lower compared with the interrupted column. The results indicate that the leaching of DOC-related metals in laboratory column experiments may be considerably underestimated compared with full-scale scenarios in which the impacts from non-equilibrium may be significantly lower. The leaching of Mo (or MoO(4)(2-)) may be controlled solely by its availability in the mobile zone, which in turn appeared to be controlled by diffusion from the stagnant zone; no Mo controlling minerals were predicted by the geochemical modeling.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Assessment of long-term leaching from waste incineration air-pollution-control residues

Assessment of long-term leaching from MSWI air-pollution-control (APC) residues is discussed with respect to use in environmental impact assessment, such as life-cycle assessment (LCA). A method was proposed for estimating leaching as a function of the liquid-to-solid (L/S) ratio in a long-term perspective (L/S 5000l/kg). Data for changes in residue pH as a function of L/S was used in combination with pH dependent leaching data to predict leachate concentrations of Al, Ca, Cd, Ba, Mg, Ni, Pb, S, Pb, V and Zn as a function of L/S. Mass balance calculations were used to determine the element fractions leached with respect to L/S. The estimated long-term leaching from a semi-dry residue and a fly ash was compared with short-term leaching determined by batch tests at L/S 10l/kg, both carbonated and non-carbonated versions of the residues were investigated. Generally, very high L/S ratios above 2000l/kg were required to leach 20-30% of the solid contents. However, Ca and S were depleted at L/S 200-900l/kg. The long-term leachate concentrations were found to either remain at the same level as the initial leaching determined by the L/S 10 batch test, or to significantly decrease compared with the initial leaching. Only Al and Zn were found to show higher leachate concentrations at L/S ratios above 3000-5000l/kg. Carbonation generally prolonged the time needed for depletion from the solid residues; however, Ca and S were depleted faster than in the case of non-carbonated residues. This study shows that uncritical use of batch leaching data for assessing the potential leaching is highly problematic, and evaluations of residue disposal should include scenario specific quantification of the long-term leaching.     

Effect of drying on leaching testing of treated municipal solid waste incineration APC-residues

Air-pollution-control (APC) residues from waste incinerators are hazardous waste according to European legislation and must be treated prior to landfilling. Batch and column leaching data determine which type of landfill can receive the treated APC-residues. CEN standards are prescribed for the batch and column leaching test; however, these standards do not specify whether or not the residue samples should be dried prior to the leaching testing. Laboratory tests were performed in parallel (dried/non-dried) on treated APC-residue samples and evaluated with respect to Cr, Cd, Cu, Pb and Zn leaching. The effect of drying of the wet APC-residue samples was particularly dramatic regarding the leaching of Cr. Drying resulted in 10-100 times more Cr leaching in both batch and columns test. Drying also affected the leaching of Cd, Cu and Pb. Initial Cd leaching was up to 100 times higher in column tests with dried APC-residue than in tests with wet residues. The effect of drying appeared to be a combination of decreasing the reduction capacity of the sample (Cr), decreasing pH (Cd, Cu) and in column tests also a wash-out of salts (probably affecting Cd and Pb). If the leaching tests are intended to mimic landfill conditions, the results of this paper suggest that the tests should be done on wet, non-dried residue samples, although this may be less practical than testing dried samples.     

Belgian MSWI fly ashes and APC residues: a characterisation study

Municipal Solid Waste Incineration (MSWI) produces different sorts of residues, bottom ash, fly ashes and Air Pollution Control (APC) residues. Generally, fly ashes and APC residues are mixed at the MSWI plant and manage as a sole residue. In this study, fly ashes and APC residues have been sampled separately at different Belgian MSWI plant and analysed by X-ray fluorescence in order to highlight the composition differences that may appear between the solids. Ca and Cl are found to be the major elements in most of the samples. Lithophilic elements, such as Al and Si, are richer in furnace and boiler ashes, as can be expected. Leaching tests also show differences between the residues; leachates from furnace and boiler ashes are alkaline while those from bag filter residues present a pH value of 6, which impacts the leaching of heavy metals (Pb and Zn). The results suggest that it could be advantageous to manage fly ashes and APC residues separately by adjusting the treatment to their specificities.     

Metal releases from a municipal solid waste incineration air pollution control residue mixed with compost

The influence of 10 wt.% mature compost was tested on the heavy metal leachate emissions from a calcium-rich municipal solid waste incineration air pollution control residue (MSWI APC). Apart from elongated columns (500 and 1250 mm), an otherwise norm compliant European percolation test setup was used. More than 99% of the metals Al, As, Cd, Cr, Cu, Fe and Ni were left in the APC residue after leaching to a liquid-to-solid ratio (L/S) of 10. Apparent short-term effects of elevated leachate DOC concentrations on heavy metal releases were not detected. Zn and Pb leachate concentrations were one order of magnitude lower for L/S 5 and 10 from the pure APC residue column, which suggests a possible long-term effect of compost on the release of these elements. Prolonging the contact time between the pore water and the material resulted in elevated leachate concentrations at L/S 0.1 to L/S 1 by a factor of 2. Only Cr and Pb concentrations were at their maxima in the first leachates at L/S 0.1. Equilibrium speciation modelling with the PHREEQC code suggested portlandite (Ca(OH)2) to control Ca solubility and pH.     

Demobilisation of critical contaminants in four typical waste-to-energy ashes by carbonation

Two bottom ashes, one air pollution control (APC) residue and one fly ash from three different Swedish municipal solid waste incineration (MSWI) plants were characterised regarding the leaching of environmentally relevant components. Characterisation was performed using a diffusion tank leaching test. The impact of carbonation on the release of eight critical components, i.e., Cl(-), Cr, Cu, Mo, Pb, Sb, Se, SO(4)(2-) and Zn, was assessed at a lab-scale and showed carbonation to have a more pronounced demobilising effect on critical components in bottom ashes than in APC residue and fly ash. From grate type incinerator bottom ash, the release of Cr decreased by 97%, by 63% for Cu and by 45% for Sb. In the investigated APC residue, the releases of Cr, Se and Pb were defined as critical, although they either remained unaffected or increased after carbonation. Cl(-) and SO(4)(2-) remained mobile after carbonation in all investigated residues.     

Solidification with water as a treatment method for air pollution control residues

The process of solidification with water was studied on air pollution control (APC) residues from incineration of refuse-derived fuel (RDF) regarding mechanical strength and leaching behaviour of solidified material. Factorial design in two levels was applied to investigate the impact of water addition, time, and temperature to mechanical strength of solidified material. Factors time and temperature, as well as the interaction between the addition of water and time significantly (alpha=0.05) influenced the mechanical strength of solidified material. The diffusion-leaching test NEN 7345 was performed to investigate if the leaching behaviour of elements from solidified material was determined by diffusion. Since it was found that leaching is not diffusion controlled, the long-term leaching behaviour was not assessed. However, the investigation showed that some of the studied components (Al, Hg, Mn, Pb, Si, and Zn) could be considerably demobilised by solidification with water. Concentrations of As, Cd, Co, Cu, Fe, and Ni were either below or not quite above the detection limits to be included in the analysis of leaching behaviour. The elements least demobilised by solidification were Cl, Cr, K, and Na.     

The influence of pH on the leaching behaviour of inorganic components from municipal solid waste APC residues

The influence of pH on the leaching behaviour of air pollution control (APC) residues produced in municipal solid waste incineration (MSWI) is addressed in this study. The residue is considered hazardous waste, and in accordance with their chemical properties, the leaching of contaminants into the environment is the main concern. Several leaching tests can be used for research studies or regulatory purposes, where a wide variety of conditions may be tested. Our work deals mainly with the leaching behaviour of toxic heavy metals (Pb, Cd, Zn, Cr, Ni, Cu) and inorganics associated with soluble salts (Na, K, Ca, Cl). The main goal is to obtain an overview of the leachability of APC residues produced in a Portuguese MSWI process. Among the different variables that may have influence on the leaching behaviour, pH of the leachant solution is the most important one, and was evaluated through pH static tests. The acid neutralization capacity (ANC) of the residue was also determined, which is in the range of 6.2–6.8 meq g^?1 (for pH = 7) and 10.1–11.6 meq g^?1 (for pH = 4). The analysis of the leaching behaviour is particularly important when the leaching is solubility controlled. The amphoteric behaviour of some elements was observed, namely for Pb and Zn, which is characterized through high solubilization at low and high pH and moderate or low solubility at neutral or moderate high pH. The solubility curves for Pb, Cd, Zn, Cr, Ni and Cu as a function of pH were obtained, which are very useful for predicting the leaching behaviour in different scenarios. The solubility of K and Na reveals to be nearly independent of the solution pH and the released amount is mainly availability-controlled. Moreover, the pH static test showed that Cl^? is the most pH-independent species. The APC residue turns out to be a hazardous waste because of the high leaching of lead and chloride. On the other hand, leaching of elements like cadmium, nickel and copper is limited by the high pH of the residue, and as long as the waste keeps its ANC, the risk of mobilization of these elements is low.     

Effect of sintering temperature on the properties and leaching of incinerator bottom ash.

The fine particle size fraction of municipal solid waste incinerator bottom ash is often problematic because reuse applications for this material are limited. In these experiments incinerator bottom ash with a particle size of less than 8 mm was processed using conventional ceramic production techniques involving wet milling, drying, compacting and sintering. The effect of sintering temperature on the sintered density, microstructure, acid neutralization capacity (ANC) and the release of metal ions as a function of leachate pH are reported. Sintering at 1080 degrees C produced samples with maximum density. This material contained diopside (CaMgSi2O6), clinoenstatite (Mg2Si2O6) and wollastonite (CaSiO3) as the major crystalline phases. The acid neutralization capacity of sintered samples is significantly lower than milled bottom ash, and further reduces as the sintering temperature increases. This is associated with reduced leaching of Ca from sintered ash samples under all leachate pH conditions. Heavy metals present in the incinerator bottom ash included Cr, Cu, Ni, Zn, Cd and Pb. Sintering under optimum conditions reduced the leachable fraction of these metals under aggressive acid conditions (leachate pH 3) by factors ranging from 90% for Ni to greater than 99% for Cr, Cd, Zn and Pb.     

Vitrification for reclaiming spent alkaline batteries

The object of this study is to stabilize spent alkaline batteries and to recover useful metals. A blend of dolomite, limestone, and cullet was added to act as a reductant and a glass matrix former in vitrification. Specimens were vitrified using an electrical heating furnace at 1400 °C and the output products included slag, ingot, flue gas, and fly ash. The major constituents of the slag were Ca, Mn, and Si, and the results of the toxicity leaching characteristics met the standards in Taiwan. The ingot was a good material for use in production of stainless steel, due to being mainly composed of Fe and Mn. For the fly ash, the high level of Zn makes it economical to recover. The distribution of metals indicated that most of Co, Cr, Cu, Fe, Mn, and Ni moved to the ingot, while Al, Ca, Mg, and Si stayed in the slag; Hg vaporized as gas phase into the flue gas; and Cd, Pb, and Zn were predominately in the fly ash. Recovery efficiency for Fe and Zn was >90% and the results show that vitrification is a promising technology for reclaiming spent alkaline batteries.     

Comparison of leaching characteristics of heavy metals in APC residue from an MSW incinerator using various extraction methods

This study investigates four extraction methods (water extraction, toxicity characteristics leaching procedure (TCLP), modified TCLP with pH control, and sequential chemical extraction (SCE)), each representing different liquid-to-solid (L/S) ratios, pH controls, and types of leachant, and their effects on the leaching concentration of heavy metals in municipal solid waste (MSW) incinerator air pollution control (APC) residue. The results indicated that for extraction with distilled water, the heavy metal leaching concentration (mg/l) decreased with L/S ratio, but the amount of heavy metal released (AHMR), defined as the leached amount of heavy metals to the weight of the tested sample (mg/kg), increased with an increase in L/S ratio, in the range of 2-100. The results also showed that both the leaching concentration and the amount of released metals were strongly pH-dependent in the TCLP and modified TCLP tests. In the case of pHs lower than 6.5, the leaching concentrations of Cd, Pb, Cu, Zn, and Cr decreased with an increase in pH. As pH increased higher than 6.5, Cr and Zn were almost insoluble. Meanwhile, Cd and Cu also showed a similar trend but at pHs of 8.5 and 7.5, respectively. Due to the nature of amphoteric elements, in the case of pHs higher than 7, the Pb leaching concentration increased with increasing pH. In modified TCLP tests with the pH value controlled at the same level as in the SCE test, the heavy metal speciation approached the extractable carbonate bound fraction by the SCE. Both amounts of targeted metals leached from the SCE and modified TCLP tests were much higher than those for the regular TCLP and water extraction tests.     

Stabilization/solidification of MSW incineration residues from facilities with different air pollution control systems. Durability of matrices versus carbonation

This paper discusses the stabilisation/solidification process with Portland cement applied to municipal solid waste incineration residues. Two types of residues were considered: fly ash (FA) produced in an electrostatic precipitator, and air pollution control (APC) residues from a semi-dry scrubber process. Cement pastes with different percentages of FA and APC residues were characterised according to their physical properties, the effect of the hydration products and their leaching behaviour. Portland pastes prepared with APC residues showed a rapid setting velocity in comparison with setting time for those pastes substituted with FA residues. Portland cement hydration was retarded in FA pastes. Leaching test results showed that heavy metals (such as Zn, Pb and Cd) and sulphates are immobilised within the paste, whereas chlorides are only partially retained. The carbonation process increases the leachability of S04(2-) and heavy metals such as Zn and Cr.     

Immobilization of lead and zinc in scrubber residues from MSW combustion using soluble phosphates

The immobilization of MSWI-scrubber residues with soluble PO4(3-) was studied and compared to the immobilization using cement. The DIN 38414-S4 leaching protocol and pH dependent leaching were used to evaluate the leaching of Pb and Zn. Four different scrubber residues from MSW combustion (Pb concentration: 2.8-4.8 mg/g; Zn concentration: 3.0-12.3 mg/g) were mixed with water and cement or Na2HPO4 as source of soluble PO4(3-) at dosages of at least 0, 0.1, 0.2, 0.3 and 0.4 g per g residue. With cement as well as with PO4(3-) a reduction in Pb and Zn leaching was observed. With 0.4 g cement per g residue, the Pb leaching was reduced by a factor ranging from 70 to 100, but still exceeded the Pb landfill limit of 2 mg/l. With PO4(3-) the Pb leaching was reduced with a factor of 100-300 to below 2 mg/l. The Zn landfill limit (10 mg/l) was only exceeded by one untreated residue. Adding 0.2 g cement or 0.1 g PO4(3-) per g of that residue was enough to reduce leaching below 10 mg/l. However, when 0.6 g Na2HPO4 per g residue was added to a lime based scrubber residue, an increase in Zn leaching up to 12.5 mg/l was observed due to an increase in pH of up to 13.0. When using NaH2PO4 and H3PO4 no such increase in Zn leaching was observed. pH dependent leaching performed on one of the four residues showed that in the pH range of 2.5-6, Pb leaching was 100-50 times lower with Na2HPO4 treatment than with cement. In the pH range from 7-11, almost equal results were obtained for cement treated and Na2HPO4 treated residue. Above a pH of 12, Pb leaching was three times lower for the PO(4)(3-)-treated residue than for the cement treated residue. With soluble PO4(3-), Pb leaching below 2 mg/l could be attained at a dosage of 0.27 g PO4(3-)/g residue. With cement, Pb leaching was never below 2 mg/l.     

Inertization of pyrite cinders and co-inertization with electric arc furnace flue dusts by pyroconsolidation at solid state

The viability of a pyroconsolidation process to render pyrite cinders inert and to co-inert pyrite cinders with a hazardous polymetallic residue such as electric arc furnace flue dusts (EAF) containing Pb, Cu, Zn, As, Cr, Ni and Mo were investigated. The effects of pyroconsolidation temperature (800-1200 degrees C), milling pyrite cinders and additions of both CaO and EAF on the resulting microstructure of the pellets were determined. The microstructural changes were then compared with the results of the standard leaching tests. Full inertization of pyrite cinders was achieved after milling to < 100 micron followed by a pelletization and pyroconsolidation process at a temperature of 1200 degrees C. This process also allows co-inertization of pyrite cinders with controlled additions of EAF (up to approximately to 10%). Following pyroconsolidation at 1200 degrees C, the metallic elements were inert components in the four main phases: traces of Cr in hematite; Cr, Cu, Zn and Ni in spinel-phase; traces of Cr and Zn in calcium ferrites; and Pb and traces of Cu, Zn and Ba in K-Ca-Al-Fe glassy silicate.     

Assessment of long-term pH developments in leachate from waste incineration residues.

Environmental assessment of residue disposal needs to account for long-term changes in leaching conditions. Leaching of heavy metals from incineration residues are highly affected by the leachate pH; the overall environmental consequences of disposing of these residues are therefore greatly influenced by changes in pH over time. The paper presents an approach for assessing pH changes in leachate from municipal solid waste incineration (MSWI) air-pollution-control (APC) residues. Residue samples were subjected to a stepwise batch extraction method in order to obtain residue samples at a range of pH values (similar to common pH-dependence tests), and then on these samples to determine leaching of alkalinity as well as remaining solid phase alkalinity. On a range of APC residues covering various pretreatment and disposal options, this procedure was used to determine leachable and residual alkalinity as a function of pH. Mass balance calculations for typical disposal scenarios were used to provide data on pH as a function of the liquid-to-solid (L/S) ratio in the leaching system. Regardless of residue type and pretreatment, pH was found to stay above 7 for L/S ratios up to about 2000 L kg(-1) corresponding to about 100,000 years in typical landfill scenarios. It was found that pH changes were mainly governed by alkalinity decreases from leaching processes rather than neutralization reactions. The results suggest that leaching testing for assessment purposes should be carried out in the alkaline range, for example, at pH 9. The paper offers a thorough basis for further modelling of incineration residue leaching and for modelling the environmental consequences of landfilling and utilization of these residues.     

Alterations of municipal solid waste incineration residues in a landfill

Fresh municipal solid waste incineration residues (MSWIR) and a drilling core of 2-10 years old landfilled MSWIR were investigated to determine the alterations due to weathering in a landfill. Physical and geochemical properties and transformations of major components and heavy metals were analyzed for fresh and landfilled residues. Carbonates and hydroxides (10-12vol%) as major mineralogical compositions in the 8-10 years weathered MSWIR were observed by modal analysis of thin sections. Three step sequential extractions indicated that reducible phases, mainly the Fe, Al and Mn hydroxides increased with depth in the landfill. A pH controlled leaching test (including availability test and pH dependent leaching test) was then conducted. Results indicated lower concentrations of leachable contents at pH values from 6 to 10 for the four elements (Pb, Zn, Al and Fe) in the 8-10 years landfilled residues than in the fresh and 1-2 years landfilled residues. This means that 8-10 years weathered MSWIR became more stable than fresh landfilled residues. The reasons for the stabilization of these elements might be the hydration of Al and Fe during weathering in the landfill, which then results in the heavy metals adsorptions of these minerals.     

Temporary stabilization of air pollution control residues using carbonation

Carbonation presents a good prospect for stabilizing alkaline waste materials. The risk of metal leaching from carbonated waste was investigated in the present study; in particular, the effect of the carbonation process and leachate pH on the leaching toxicity of the alkaline air pollution control (APC) residues from municipal solid waste incinerator was evaluated. The pH varying test was conducted to characterize the leaching characteristics of the raw and carbonated residue over a broad range of pH. Partial least square modeling and thermodynamic modeling using Visual MINTEQ were applied to highlight the significant process parameters that controlled metal leaching from the carbonated residue. By lowering the pH to 8-11, the carbonation process reduced markedly the leaching toxicity of the alkaline APC residue; however, the treated APC residue showed similar potential risk of heavy metal release as the raw ash when subjected to an acid shock. The carbonated waste could, thereby, not be disposed of safely. Nonetheless, carbonation could be applied as a temporary stabilization process for heavy metals in APC residues in order to reduce the leaching risk during its transportation and storage before final disposal.     

Radionuclide behavior at the Oklo nuclear reactor, Gabon

The Oklo natural reactor, Gabon, remains the best natural analog for assessing the behavior of fission products, actinides, and actinide daughters in rocks. The rocks at Oklo are porous and permeable, as well as fractured and contain abundant water, yet many of the fission products and actinides have remained in place or close to their formation sites. The actinides Th, U, Np, Pu, and Am are similar in their crystal chemical characteristics, and were all retained in the host pitchblende. Elements incompatible in the pitchblende structure were lost by diffusion or other processes into the rocks surrounding the high-grade reactor ore. Alkali and alkaline earth elements Rb, Sr, Cs, and Ba were fixed in and very close to the reactor ores in clay minerals and in some secondary carbonates and sulfates. Local oxidizing conditions in the reactor zones caused some loss of Tc, Mo, Cd, adn Ru, but Tc, Mo, and Ru, were fixed in sulfides formed under close-by chemically reducing conditions. Local migration for Ag and Sn has been documented for some samples. Probable overall retention is indicated for Rh, Ru, Te, Nb, Zr, and Sb. Deficiencies in fissiogenic I and Kr, Xe have been noted, and data are not available for fissiogenic Br. Also, Oklo remains a logical site for in-depth study of present- and paleohydrology-stable isotopy, as well as distribution of fission products and actinides in UO₂ and surrounding minerals.