Determination of Microgram Quantities of Inorganic Sulfate in Atmospheric Particulates

Abstract

Before a community-wide woodstove changeout program, a chemical mass balance (CMB) source apportionment study was conducted in Libby, MT, during the winter of 2003–2004 to identify the sources of fine particulate matter (PM_2.5) within the valley. Results from this study showed that residential woodstoves were the major source, contributing approximately 80% of the ambient PM_2.5 throughout the winter months. In an effort to lower the ambient PM_2.5, a large woodstove changeout program was conducted in Libby from 2005 to 2007 in which nearly 1200 old woodstoves were changed out with cleaner burning models. During the winter of 2007–2008, a follow-up CMB source apportionment study was conducted to evaluate the effectiveness of the changeout. Results from this study showed that average winter PM_2.5 mass was reduced by 20%, and woodsmoke-related PM_2.5 (as identified by the CMB model) was reduced by 28% when compared with the pre-changeout winter of 2003– 2004. These results suggest that a woodstove changeout can be an effective tool in reducing ambient levels of PM_2.5 in woodstove-impacted communities.     

The impact of wood stove technology upgrades on indoor residential air quality

Fine particulate matter (PM_2.5) air pollution has been linked to adverse health impacts, and combustion sources including residential wood-burning may play an important role in some regions. Recent evidence suggests that indoor air quality may improve in homes where older, non-certified wood stoves are exchanged for lower emissions EPA-certified alternatives. As part of a wood stove exchange program in northern British Columbia, Canada, we sampled outdoor and indoor air at 15 homes during 6-day sampling sessions both before and after non-certified wood stoves were exchanged. During each sampling session two consecutive 3-day PM_2.5 samples were collected onto Teflon filters, which were weighed and analyzed for the wood smoke tracer levoglucosan. Residential PM_2.5 infiltration efficiencies (F_inf) were estimated from continuous light scattering measurements made with nephelometers, and estimates of F_inf were used to calculate the outdoor- and indoor-generated contributions to indoor air. There was not a consistent relationship between stove technology and outdoor or indoor concentrations of PM_2.5 or levoglucosan. Mean F_inf estimates were low and similar during pre- and post-exchange periods (0.32 ± 0.17 and 0.33 ± 0.17, respectively). Indoor sources contributed the majority (～65%) of the indoor PM_2.5 concentrations, independent of stove technology, although low indoor-outdoor levoglucosan ratios (median ≤ 0.19) and low indoor PM_2.5-levoglucosan correlations (r ≤ 0.19) suggested that wood smoke was not a major indoor PM_2.5 source in most of these homes. In summary, despite the potential for extensive wood stove exchange programs to reduce outdoor PM_2.5 concentrations in wood smoke-impacted communities, we did not find a consistent relationship between stove technology upgrades and indoor air quality improvements in homes where stoves were exchanged.     

Evaluating an Air Quality Health Index (AQHI) amendment for communities impacted by residential woodsmoke in British Columbia,Canada

ABSTRACT

Smoke from burning biomass is an important source of fine particulate matter (PM_2.5), but the health risks may not be fully captured by the Canadian Air Quality Health Index (AQHI). In May 2018, the province of British Columbia launched an evidence-based amendment (AQHI-Plus) to improve AQHI performance for wildfire smoke, but the AQHI-Plus was not developed or tested on data from the residential woodsmoke season. This study assesses how the AQHI and AQHI-Plus are associated with acute health outcomes during the cooler seasons of 2010–2017 in British Columbia, Canada. Monthly and daily patterns of temperature and PM_2.5 concentrations were used to identify Local Health Areas (LHAs) that were impacted by residential woodsmoke. The effects of the AQHI and AQHI-Plus on five acute health outcomes (including non-accidental mortality, outpatient physician visits, and medical dispensations for cardiopulmonary conditions) were estimated using generalized linear mixed effect models with Poisson distributions adjusted for long- and short-term temperature trends. Values of the Akaike information criterion (AIC) were compared to evaluate whether the AQHI or AQHI-Plus was better fitted to each health outcome. Eleven LHAs were categorized as woodsmoke-impacted. In these LHAs, the AQHI and AQHI-Plus associations with acute health outcomes were sensitive to temperature adjustments. After temperature adjustments, the most consistent associations were observed for the two asthma-specific outcomes where the AQHI-Plus was better fitted than the AQHI. The improved performance of the AQHI-Plus for susceptible populations with asthma is consistent between communities impacted by residential woodsmoke and wildfire smoke.

Implications: Canada’s Air Quality Health Index (AQHI) is a three pollutant index used to communicate the short term health impact of degraded air quality. As fine particulate matter (PM_2.5) is the lowest weighted pollutant in the AQHI, the index is poorly reflective of woodsmoke impacts. The present analysis found that an AQHI amendment developed for improved sensitivity to PM_2.5 during wildfire seasons (AQHI-Plus) is also more predictive of acute asthma-related health outcomes in communities impacted by residential woodsmoke. The BC Ministry of Environment and Climate Change Strategy has piloted the AQHI-Plus year-round. Other jurisdictions should consider whether their air quality indices are reflective of the risks posed by woodsmoke.     

The impact of wood smoke on ambient PM2.5 in northern Rocky Mountain valley communities

During the winters of 2006/2007 and 2007/2008, PM_2.5 source apportionment programs were carried out within five western Montana valley communities. Filter samples were analyzed for mass and chemical composition. Information was utilized in a Chemical Mass Balance (CMB) computer model to apportion the sources of PM_2.5. Results showed that wood smoke (likely residential woodstoves) was the major source of PM_2.5 in each of the communities, contributing from 56% to 77% of the measured wintertime PM_2.5. Results of ¹⁴C analyses showed that between 44% and 76% of the measured PM_2.5 came from a new carbon (wood smoke) source, confirming the results of the CMB modeling. In summary, the CMB model results, coupled with the ¹⁴C results, support that wood smoke is the major contributor to the overall PM_2.5 mass in these rural, northern Rocky Mountain airsheds throughout the winter months.     

Seasonal ambient particulate matter and population health outcomes among communities impacted by road dust in British Columbia,Canada

In recent years, many air quality monitoring programs have favored measurement of particles less than 2.5 µm (PM_2.5) over particles less than 10 µm (PM₁₀) in light of evidence that health impacts are mostly from the fine fraction. However, the coarse fraction (PM_10-2.5) may have independent health impacts that support continued measurement of PM₁₀ in some areas, such as those affected by road dust. The objective of this study was to evaluate the associations between different measures of daily PM exposure and two daily indicators of population health in seven communities in British Columbia, Canada, where road dust is an ongoing concern. The measures of exposure were PM₁₀, PM_2.5, PM_10-2.5, PM_2.5 adjusted for PM_10-2.5, and PM_10-2.5 adjusted for PM_2.5. The indicators of population health were dispensations of the respiratory reliever medication salbutamol sulfate and nonaccidental mortality. This study followed a time-series design using Poisson regression over a 2003–2015 study period, with analyses stratified by three seasons: residential woodsmoke in winter; road dust in spring; and wildfire smoke in summer. A random-effects meta-analysis was conducted to establish a pooled estimate. Overall, an interquartile range increase in daily PM_10-2.5 was associated with a 3.6% [1.6, 5.6] increase in nonaccidental mortality during the road dust season, which was reduced to 3.1% [0.8, 5.4] after adjustment for PM_2.5. The adjusted coarse fraction had no effect on salbutamol dispensations in any season. However, an interquartile range increase in PM_2.5 was associated with a 2.7% [2.0, 3.4] increase in dispensations during the wildfire season. These analyses suggest different impacts of different PM fractions by season, with a robust association between the coarse fraction and nonaccidental mortality in communities and periods affected by road dust. We recommend that PM₁₀ monitoring networks be maintained in these communities to provide feedback for future dust mitigation programs.

Implications: There was a significant association between daily concentrations of the coarse fraction and nonaccidental mortality during the road dust season, even after adjustment for the fine fraction. The acute and chronic health effects associated with exposure to the coarse fraction remain unclear, which supports the maintenance of PM₁₀ monitoring networks to allow for further research in communities affected by sources such as road dust.     

Particulate organic compounds emitted from experimental wildland fires in a Mediterranean ecosystem

Fine (PM_2.5) and coarse (PM_2.5–10) smoke particles from controlled biomass burnings of a shrub-dominated forest in Lousã Mountain, Portugal, enabled the quantification by chromatographic techniques of several molecular tracers for the combustion of Mediterranean forest ecosystems, which could be conducive to source apportionment studies. The major organic components in the smoke samples were pyrolysates of vegetation cuticles, mainly comprising steradienes and sterol derivatives, carbohydrates from the breakdown of cellulose, aliphatic lipids from vegetation waxes and methoxyphenols from the lignin thermal degradation. Most of these compounds are chiefly found in fine particles. Polycyclic aromatic hydrocarbons (PAH) were also present as minor constituents. Anhydrosugar and PAH molecular diagnostic ratios were applied as source assignment tools. Some biomarkers are reported for the first time in biomass burning smoke.     

Indoor particle size distributions in homes with open fires and improved Patsari cook stoves

Particulate pollution has been clearly linked with adverse health impacts from open fire cookstoves, and indoor air concentrations are frequently used as a proxy for exposures in health studies. Implicit are the assumptions that the size distributions for the open fire and improved stove are not significantly different, and that the relationship between indoor concentrations and personal exposures is the same between stoves. To evaluate the impact of these assumptions size distributions of particulate matter in indoor air were measured with the Sioutas cascade impactor in homes using open fires and improved Patsari stoves in a rural Purepecha community in Michoacan, Mexico. On average indoor concentrations of particles less than 0.25 μm were 72% reduced in homes with improved Patsari stoves, reflecting a reduced contribution of this size fraction to PM_2.5 mass concentrations from 68% to 48%. As a result the mass median diameter of indoor PM_2.5 particulate matter was increased by 29% with the Patsari improved stove compared to the open fire (from 0.42 μm to 0.59 μm, respectively). Personal PM_2.5 exposure concentrations for women in homes using open fires were approximately 61% of indoor concentration levels (156 μg m^?3 and 257 μg m^?3 respectively). In contrast personal exposure concentrations were 77% times indoor air concentration levels for women in homes using improved Patsari stoves (78 μg m^?3and 101 μg m^?3 respectively). Thus, if indoor air concentrations are used in health and epidemiologic studies significant bias may result if the shift in size distribution and the change in relationship between indoor air concentrations and personal exposure concentrations are not accounted for between different stove types.     

Indoor particulate matter in urban residences of Alexandria,Egypt

Indoor particulate matter samples were collected in 17 homes in an urban area in Alexandria during the summer season. During air measurement in all selected homes, parallel outdoor air samples were taken in the balconies of the domestic residences. It was found that the mean indoor PM_2.5 and PM₁₀ (particulate matter with an aerodynamic diameter ≤2.5 and ≤10 μm, respectively) concentrations were 53.5 ± 15.2 and 77.2 ± 15.1 µg/m³, respectively. The corresponding mean outdoor levels were 66.2 ± 16.5 and 123.8 ± 32.1 µg/m³, respectively. PM_2.5 concentrations accounted, on average, for 68.8 ± 12.8% of the total PM₁₀ concentrations indoors, whereas PM_2.5 contributed to 53.7 ± 4.9% of the total outdoor PM₁₀ concentrations. The median indoor/outdoor mass concentration (I/O) ratios were 0.81 (range: 0.43–1.45) and 0.65 (range: 0.4–1.07) for PM_2.5 and PM₁₀, respectively. Only four homes were found with I/O ratios above 1, indicating significant contribution from indoor sources. Poor correlation was seen between the indoor PM₁₀ and PM_2.5 levels and the corresponding outdoor concentrations. PM₁₀ levels were significantly correlated with PM_2.5 loadings indoors and outdoors and this might be related to PM₁₀ and PM_2.5 originating from similar particulate matter emission sources. Smoking, cooking using gas stoves, and cleaning were the major indoor sources contributed to elevated indoor levels of PM₁₀ and PM_2.5.

Implications: The current study presents results of the first PM_2.5 and PM₁₀ study in homes located in the city of Alexandria, Egypt. Scarce data are available on indoor air quality in Egypt. Poor correlation was seen between the indoor and outdoor particulate matter concentrations. Indoor sources such as smoking, cooking, and cleaning were found to be the major contributors to elevated indoor levels of PM₁₀ and PM_2.5.     

Physicochemical and toxicological characteristics of urban aerosols during a recent Indonesian biomass burning episode

Air particulate matter (PM) samples were collected in Singapore from 21 to 29 October 2010. During this time period, a severe regional smoke haze episode lasted for a few days (21–23 October). Physicochemical and toxicological characteristics of both haze and non-haze aerosols were evaluated. The average mass concentration of PM_2.5 (PM with aerodynamic diameter of ≤2.5 μm) increased by a factor of 4 during the smoke haze period (107.2 μg/m³) as compared to that during the non-smoke haze period (27.0 μg/m³). The PM_2.5 samples were analyzed for 16 priority polycyclic aromatic hydrocarbons (PAHs) listed by the United States Environmental Protection Agency and 10 transition metals. Out of the seven PAHs known as potential or suspected carcinogens, five were found in significantly higher levels in smoke haze aerosols as compared to those in the background air. Metal concentrations were also found to be higher in haze aerosols. Additionally, the toxicological profile of the PM_2.5 samples was evaluated using a human epithelial lung cell line (A549). Cell viability and death counts were measured after a direct exposure of PM_2.5 samples to A459 cells for a period of 48 h. The percentage of metabolically active cells decreased significantly following a direct exposure to PM samples collected during the haze period. To provide further insights into the toxicological characteristics of the aerosol particles, glutathione levels, as an indirect measure of oxidative stress and caspase-3/7 levels as a measure of apoptotic death, were also evaluated.     

Seasonal variation of ionic species in fine particles at Qingdao,China

Totally nine measurement campaigns for ambient particles and SO₂ have been conducted during the period of 1997–2000 in Qingdao in order to understand the characteristics of the particulate matter in coastal areas of China. The mass fractions of PM_2.5, PM_2.5−10 and PM_>10 in TSP are 49%, 25% and 26%, respectively. The size distribution of particles mass concentrations in Qingdao shows bi-modal distribution. Mass fraction percentages of water-soluble ions in PM_2.5, PM_2.5−10 and PM_>10 decreased from 62% to 35% and 21%. In fine particles, sulfate, nitrate and ammonium, secondary formed compounds, are major components, totally accounting for 50% of PM_2.5 mass concentration.The ratios of sulfate, chloride, ammonium and potassium in PM_2.5 for heating versus non-heating periods are 1.34, 1.80, 1.56 and 1.44, respectively. The ratio of nitrate is 3.02 and this high ratio could be caused by reduced volatilization at lower temperature. Sulfate concentrations are higher than nitrate in PM_2.5. The chemical forms of sulfate and nitrate are probably (NH₄)₂SO₄ and NH₄NO₃ and chloride depletion was observed.Backward trajectory analysis reflected possible influence of air pollutant transport to Qingdao local aerosol pollution.     

Concentrations of ultrafine,fine and PM2.5 particles in three European cities

Total number concentrations, number concentrations of ultrafine (0.01–0.1 μm) and accumulation (0.1–0.5 μm) particles, as well as mass concentration of PM_2.5 particles and blackness of PM_2.5 filters, which is related to Black Smoke were simultaneously monitored in three European cities during the winter period for three and a half months. The purpose of the study was to describe the differences in concentration levels and daily and diurnal variations in particle number and mass concentrations between European cities. The results show statistically significant differences in the concentrations of PM_2.5 and the blackness of the PM_2.5 filters between the cities, but not in the concentrations of ultrafine particles. Daily PM_2.5 levels were found to be poorly correlated with the daily total and ultrafine number concentrations but better correlated with the number concentration of accumulation particles. According to the principal component analysis airborne particulate pollutants seem to be divided into two major source categories, one identified with particle number concentrations and the other related to mass-based information. The present results underline the importance of using both particle number and mass concentrations to evaluate urban air quality.     

Monitoring and Source Apportionment of Particulate Matter near a Large Phosphorus Production Facility

ABSTRACT

A source apportionment study was conducted to identify sources within a large elemental phosphorus plant that contribute to exceedances of the National Ambient Air Quality Standards (NAAQS) for 24-hr PM₁₀. Ambient data were collected at three monitoring sites from October 1996 through July 1999, and included the following: 24-hr PM₁₀ mass, 24-hr PM_2.5 and PM_10–2.5 mass and chemistry, continuous PM₁₀and PM_2.5 mass, continuous meteorological data, and wind-direction-resolved PM_2.5 and PM₁₀ mass and chemistry. Ambient-based receptor modeling and wind-directional analysis were employed to help identify major sources or source locations and source contributions. Fine-fraction phosphate was the dominant species observed during PM₁₀ exceedances, though in general, re-suspended coarse dusts from raw and processed materials at the plant were also needed to create an exceedance. Major sources that were identified included the calciners, the CO flares, process-related dust, and electric-arc furnace operations.     

Temporal patterns in daily measurements of inorganic and organic speciated PM2.5 in Denver

Airborne particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5) has been linked to a wide range of adverse health effects and as a result is currently regulated by the U.S. Environmental Protection Agency. PM_2.5 originates from a multitude of sources and has heterogeneous physical and chemical characteristics. These features complicate the link between PM_2.5 emission sources, ambient concentrations and health effects. The goal of the Denver Aerosol Sources and Health (DASH) study is to investigate associations between sources and health using daily measurements of speciated PM_2.5 in Denver.The datxa set being collected for the DASH study will be the longest daily speciated PM_2.5 data set of its kind covering 5.5 years of daily inorganic and organic speciated measurements. As of 2008, 4.5 years of bulk measurements (mass, inorganic ions and total carbon) and 1.5 years of organic molecular marker measurements have been completed. Several techniques were used to reveal long-term and short-term temporal patterns in the bulk species and the organic molecular marker species. All species showed a strong annual periodicity, but their monthly and seasonal behavior varied substantially. Weekly periodicities appear in many compound classes with the most significant weekday/weekend effect observed for elemental carbon, cholestanes, hopanes, select polycyclic aromatic hydrocarbons (PAHs), heavy n-alkanoic acids and methoxyphenols. Many of the observed patterns can be explained by meteorology or anthropogenic activity patterns while others do not appear to have such obvious explanations. Similarities and differences in these findings compared to those reported from other cities are highlighted.     

Reduction of atmospheric fine particle level by restricting the idling vehicles around a sensitive area

Atmospheric particles are a major problem that could lead to harmful effects on human health, especially in densely populated urban areas. Chiayi is a typical city with very high population and traffic density, as well as being located at the downwind side of several pollution sources. Multiple contributors for PM_2.5 (particulate matter with an aerodynamic diameter ≥2.5 μm) and ultrafine particles cause complicated air quality problems. This study focused on the inhibition of local emission sources by restricting the idling vehicles around a school area and evaluating the changes in surrounding atmospheric PM conditions. Two stationary sites were monitored, including a background site on the upwind side of the school and a campus site inside the school, to monitor the exposure level, before and after the idling prohibition. In the base condition, the PM_2.5 mass concentrations were found to increase 15% from the background, whereas the nitrate (NO₃^?) content had a significant increase at the campus site. The anthropogenic metal contents in PM_2.5 were higher at the campus site than the background site. Mobile emissions were found to be the most likely contributor to the school hot spot area by chemical mass balance modeling (CMB8.2). On the other hand, the PM_2.5 in the school campus fell to only 2% after idling vehicle control, when the mobile source contribution reduced from 42.8% to 36.7%. The mobile monitoring also showed significant reductions in atmospheric PM_2.5, PM_0.1, polycyclic aromatic hydrocarbons (PAHs), and black carbon (BC) levels by 16.5%, 33.3%, 48.0%, and 11.5%, respectively. Consequently, the restriction of local idling emission was proven to significantly reduce PM and harmful pollutants in the hot spots around the school environment.

Implications: The emission of idling vehicles strongly affects the levels of particles and relative pollutants in near-ground air around a school area. The PM_2.5 mass concentration at a campus site increased from the background site by 15%, whereas NO₃^? and anthropogenic metals also significantly increased. Meanwhile, the PM_2.5 contribution from mobile source in the campus increased 6.6% from the upwind site. An idling prohibition took place and showed impressive results. Reductions of PM_2.5, ionic component, and non-natural metal contents were found after the idling prohibition. The mobile monitoring also pointed out a significant improvement with the spatial analysis of PM_2.5, PM_0.1, PAH, and black carbon concentrations. These findings are very useful to effectively improve the local air quality of a densely city during the rush hour.     

Evaluation of Time-Resolved PM2.5 Data in Urban/Suburban Areas of New Jersey

ABSTRACT

Time-resolved data is needed for public notification of unhealthful air quality and to develop an understanding of atmospheric chemistry, including insights important to control strategies. In this research, continuous fine particulate matter (PM_2.5) mass concentrations were measured with tapered element oscillating microbalances (TEOMs) across New Jersey from July 1997 to June 1998. Data features indicating the influence of local sources and long-distance transport are examined, as well as differences between 1-hr maxima and 24-hr average concentrations that might be relevant to acute health effects. Continuous mass concentrations were not significantly different from filter-collected gravimetric mass concentrations with 95% confidence intervals during any season. Annual mean PM_2.5 concentrations from July 1997 to June 1998 were 17.3, 16.4, 14.1, and 15.3 μg/m³ at Newark, Elizabeth, New Brunswick, and Camden, NJ, respectively. Monthly averaged 24- and 1-hr daily maximum PM_2.5 concentrations suggest the existence of a high PM_2.5 (May-October) and a low PM_2.5 (November-April) season.

PM_2.5 magnitudes and temporal trends were very similar across the state during high PM_2.5 events. In fact, the between-site coefficients of determination (R²) for daily PM_2.5 measurements were 84-98% for June and July. Additionally, during the most pronounced PM_2.5 episode, PM_2.5 concentrations closely tracked the daily maximum 1-hr O₃ concentrations. These observations suggest the importance of transport and atmospheric chemistry (i.e., secondary formation) to PM_2.5 episodes in New Jersey. The influence of local sources was observed in diurnal concentration profiles and annual average between-site differences. Urban wintertime data illustrate that high 1-hr maximum PM_2.5 concentrations can occur on low 24-hr PM_2.5 days.     

Roadside Particulate Air Pollution in Bangkok

Abstract

Airborne fine particles of PM_2.5-10 and PM_2.5 in Bangkok, Nonthaburi, and Ayutthaya were measured from December 22, 1998, to March 26, 1999, and from November 30, 1999, to December 2, 1999. Almost all the PM₁₀ values in the high-polluted (H) area exceeded the Thailand National Ambient Air Quality Standards (NAAQS) of 120 μg/m³. The low-polluted (L) area showed low PM₁₀ (34–74 μg/m³ in the daytime and 54–89 μg/m³ at night). PM_2.5 in the H area varied between 82 and 143 μg/m³ in the daytime and between 45 and 146 μg/m³ at night. In the L area, PM_2.5 was quite low both day and night and varied between 24 and 54 μg/m³, lower than the U.S. Environmental Protection Agency (EPA) standard (65 μg/m³). The personal exposure results showed a significantly higher proportion of PM_2.5 to PM₁₀ in the H area than in the L area (H = 0.80 ± 0.08 and L = 0.65 ± 0.04).

Roadside PM₁₀ was measured simultaneously with the Thailand Pollution Control Department (PCD) monitoring station at the same site and at the intersections where police work. The result from dual simultaneous measurements of PM₁₀ showed a good correlation (correlation coefficient: r = 0.93); however, PM levels near the roadside at the intersections were higher than the concentrations at the monitoring station. The relationship between ambient PM level and actual personal exposures was examined. Correlation coefficients between the general ambient outdoors and personal exposure levels were 0.92 for both PM_2.5 and PM₁₀.

Bangkok air quality data for 1997–2000, including 24-hr average PM₁₀, NO₂, SO₂, and O₃ from eight PCD monitoring stations, were analyzed and validated. The annual arithmetic mean PM₁₀ of the PCD data at the roadside monitoring stations for the last 3 years decreased from 130 to 73 μg/m³, whereas the corresponding levels at the general monitoring stations decreased from 90 to 49 μg/m³. The proportion of days when the level of the 24-hr average PM₁₀ exceeded the NAAQS was between 13 and 26% at roadside stations. PCD data showed PM₁₀ was well correlated with NO₂ but not with SO₂, suggesting that automobile exhaust is the main source of the particulate air pollution. The results obtained from the simultaneous measurement of PM_2.5 and PM₁₀ indicate the potential environmental health hazard of fine particles. In conclusion, Bangkok traffic police were exposed to high levels of automobile-derived particulate air pollution.     

Concentrations,properties, and health risk of PM2.5 in the Tianjin City subway system

A campaign was conducted to assess and compare the personal exposure in L3 of Tianjin subway, focusing on PM_2.5 levels, chemical compositions, morphology analysis, as well as the health risk of heavy metal in PM_2.5. The results indicated that the average concentration of the PM_2.5 was 151.43 μg/m³ inside the train of the subway during rush hours. PM_2.5 concentrations inside car under the ground are higher than those on the ground, and PM_2.5 concentrations on the platform are higher than those inside car. Regarding metal concentrations, the highest element in PM_2.5 samples was Fe; the level of which is 17.55 μg/m³. OC is a major component of PM_2.5 in Tianjin subway. Secondary organic carbon is the formation of gaseous organic pollutants in subway. SEM–EDX and TEM–EDX exhibit the presence of individual particle with a large metal content in the subway samples. For small Fe metal particles, iron oxide can be formed easily. With regard to their sources, Fe-containing particles are generated mainly from mechanical wear and friction processes at the rail–wheel–brake interfaces. The non-carcinogenic risk to metals Cr, Ni, Cu, Zn and Pb, and carcinogenic hazard of Cr and Ni were all below the acceptable level in L3 of Tianjin subway.

     

Spatial differences in ambient coarse and fine particles in the Monterrey metropolitan area,Mexico: Implications for source contribution

The ambient air of the Monterrey Metropolitan Area (MMA) in Mexico frequently exhibits high levels of PM₁₀ and PM_2.5. However, no information exists on the chemical composition of coarse particles (PM_c = PM₁₀ – PM_2.5). A monitoring campaign was conducted during the summer of 2015, during which 24-hr average PM₁₀ and PM_2.5 samples were collected using high-volume filter-based instruments to chemically characterize the fine and coarse fractions of the PM. The collected samples were analyzed for anions (Cl^–, NO₃^–, SO₄^2–), cations (Na⁺, NH₄⁺, K⁺), organic carbon (OC), elemental carbon (EC), and 35 trace elements (Al to Pb). During the campaign, the average PM_2.5 concentrations did not showed significance differences among sampling sites, whereas the average PM_c concentrations did. In addition, the PM_c accounted for 75% to 90% of the PM₁₀ across the MMA. The average contribution of the main chemical species to the total mass indicated that geological material including Ca, Fe, Si, and Al (45%) and sulfates (11%) were the principal components of PM_c, whereas sulfates (54%) and organic matter (30%) were the principal components of PM_2.5. The OC-to-EC ratio for PM_c ranged from 4.4 to 13, whereas that for PM_2.5 ranged from 3.97 to 6.08. The estimated contribution of Secondary Organic Aerosol (SOA) to the total mass of organic aerosol in PM_2.5 was estimated to be around 70–80%; for PM_c, the contribution was lower (20–50%). The enrichment factors (EF) for most of the trace elements exhibited high values for PM_2.5 (EF: 10–1000) and low values for PM_c (EF: 1–10). Given the high contribution of crustal elements and the high values of EFs, PM_c is heavily influenced by soil resuspension and PM_2.5 by anthropogenic sources. Finally, the airborne particles found in the eastern region of the MMA were chemically distinguishable from those in its western region.

Implications: Concentration and chemical composition patterns of fine and coarse particles can vary significantly across the MMA. Public policy solutions have to be built based on these observations. There is clear evidence that the spatial variations in the MMA’s coarse fractions are influenced by clearly recognizable primary emission sources, while fine particles exhibit a homogeneous concentration field and a clear spatial pattern of increasing secondary contributions. Important reductions in the coarse fraction can come from primary particles’ emission controls; for fine particles, control of gaseous precursors—particularly sulfur-containing species and organic compounds—should be considered.     

Effects of fine particles on children’s hospital admissions for respiratory health in Seville,Spain

This study analyzes the influence of fine particles PM_2.5 on nonprogrammed children’s hospital admissions that occurred in the city of Seville between 2007 and 2011, and makes an economic assessment of the cost of the children’s hospital admissions for respiratory causes due to particle pollution. The PM_2.5 dose-response functions for each type of hospital admission were used to quantify the cost of the hospital admissions. It can be concluded that the PM_2.5 concentrations have negative effects on bronchiolitis, pneumonia, asthma, and bronchitis and other causes. A reduction of the daily average annual PM_2.5 concentration from the existing levels to 10 µg/m³ would show an annual average reduction of children’s hospital admissions due to respiratory diseases of 0.09 cases. This paper shows that the daily average cost for children hospital admissions due to respiratory reasons in the city of Seville, associated with daily average annual levels of PM_2.5 above 10 µg/m³, was almost 200€.

Implications:?Elevated PM_2.5 concentrations in Seville have negative effects on children’s bronchiolitis, pneumonia, asthma, and bronchitis and other causes. A reduction of the daily average annual PM_2.5 concentration from the existing levels to 10 μg/m³ would suppose an annual mean reduction of children’s hospital admissions due to respiratory diseases of 0.09 cases.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.