高浓度硫化染料染色废水的处理与综合利用

采用混凝气浮－内电解－接触氧化组合工艺处理高浓度硫化染料染色废水，生产运行结果表明：S^2-、COD、BOD5和色度的去除率分别为近100％、94％左右、92．5％－94．8％、96％－100％，处理后出水的各项污染指标均符合国家排放标准，并且实现了部分回用。该处理工艺设备简单、系统运行稳定、投资少、操作方便，具有一定的推广应用价值。     

SPD型高效气浮装置在火电厂废水处理中的应用

介绍了SPD型高效气浮装置的工作原理、主要结构、工艺特点和在火电厂中的运行使用情况。该工艺适合火电厂工业废水处理,具有投资低、占地少、处理废水速度快及处理水量大等特点,在火电厂废水处理中有很好的推广使用价值。     

邻苯二甲酸二辛酯废水的处理

采用压滤－刮油－中和吸附－压滤－吸附工艺处理邻苯二甲酸二辛酯废水,对处理工艺的运行条件进行了探讨。出水COD和石油类的去除率分别达到97．7％和99．8％。该法设备简单、投资少、操作方便,对排放量较小的邻苯二甲酸二辛酯废水的处理是行之有效的方法。     

海水烟气脱硫工艺在火电厂的应用

介绍了海水烟气脱硫工艺的基本原理，工艺流程，设计参数、工艺特点和实际运行效果，并提出该工艺在火电厂应用中的注意事项。     

AO1O2工艺处理染色废水

报导了豆腐营工业区污水集中控制示范工程，采用水解酸化（Ａ）－接触氧化（Ｏ１）－合建式氧化沟（Ｏ２）净化组合工艺处理染色废水的运行情况。该工艺具有处理效果好、运行稳定、投产快、操作管理简便、占地少、投资省、处理成本低等优点。     

太原第一热电厂简易湿法脱硫技术及经济分析

介绍中日使用太原第一热电厂简易湿法烟气脱硫（太－ＦＧＤ）的工艺、装置及运行状况,论述其特点和国产化问题,重点对建设和运行费用进行了分析,指出太－ＦＧＤ对我国火电厂脱硫,特别是建厂时没有预留脱硫场地的老厂改造具有应用前景。     

考虑SO2环境损害的燃煤电厂脱硫经济性评价

基于“环境成本内部化”的思想，利用广东某燃煤电厂大气污染损害的估算结果，将二氟化硫对环境的损害作为一种环境投资加入到各种脱硫工艺的一次投资中，对目前用于我国火电厂的主要脱硫工艺进行了综合经济评价。结果表明，各种脱硫工艺的投资成本与未考虑环境损害因素时有了显著变化。     

火电厂电缆安全状况调查

通过对30家火电厂92台机组电缆安全状况的调查,研究了火电厂电缆安全技术管理体系的建立和执行情况、电缆设备状况、电缆安全技术措施以及运行管理状况。指出火电厂电缆安全状况在安全管理体系不健全、电缆设备安全隐患较多、安全技术措施不到位且运行管理相对较为松懈等问题,加大了火电厂电缆事故发生机率。针对电缆安全技术现状和管理现状,提出了提高和改善火电厂电缆安全水平的技术和管理措施。     

循环水排水处理的新工艺及其应用

火电厂循环水排污水回收后,经过滤、离子交换器、超滤、反渗透处理后,作为循环水补水及锅炉补给水处理车间的原水进行再次使用,系统产生的废水可用于电厂煤场喷洒及冲灰.此种处理方式,可以降低新鲜取水量,降低循环水的结垢趋势,提高锅炉补给水制水设备的运行周期,同时实现火电厂废水“零排放”.对该技术实施后的经济效益进行了分析,并对实施过程中加药工艺、设备投运等提出了改进方案.     

高效分离池—絮凝沉淀法处理火电厂工业废水

采用高效分离池－絮凝沉淀法新工艺处理新乡火电厂２００ＭＷ机组工业废水，１年的运行效果表明，处理后的水质良好，达到了循环冷却水的水质要求，回用于冷却水的补充水，每年可回收３５０万ｔ。系统运行正常，性能稳定。本工艺具有占地小、投资小、设施简单、处理效果好等优点。     

欧盟包装废物管理和总体产生特性分析

欧盟旱在1994年就颁布了包装和包装废物的指令，提出了包装废物管理的目标和管理内容，要求各成员国采取积极的经济和法律措施，建立自由流通的公平市场秩序。通过研究评估表明，包装和包装废物指令的实施产生了多方面的积极影响。统计数据表明，历年包装废物回收总量平稳增加，处置量平稳下降，单位GDP产值产生包装废物的系数基本保持稳定，但各国包装废物人均产生量存在较大差异。     

Oil Spill Modeling towards the Close of the 20th Century: Overview of the State of the Art

The state-of-the-art in oil spill modeling is summarized, focusing primarily on the years from 1990 to the present. All models seek to describe the key physical and chemical processes that transport and weather the oil on and in the sea. Current insights into the mechanisms of these processes and the availability of algorithms for describing and predicting process rates are discussed. Advances are noted in the areas of advection, spreading, evaporation, dispersion, emulsification, and interactions with ice and shorelines. Knowledge of the relationship between oil properties, and oil weathering and fate, and the development of models for the evaluation of oil spill response strategies are summarized. Specific models are used as examples where appropriate. Future directions in these and other areas are indicated     

Pyrolysis of tyres. Influence of the final temperature of the process on emissions and the calorific value of the products recovered

A study was made of the pyrolysis of tyre particles, with the aim of determining the possibilities of using the products resulting from the process as fuel. Three final temperatures were used, determined from thermogravimetric data. The design of the experiment was a horizontal oven containing a reactor into which particles of the original tyre were placed. After the process, a solid fraction (char) remained in the reactor, while the gases generated went through a set of scrubbers where most of the condensable fraction (oils) was retained. Finally, once free of this fraction, the gases were collected in glass ampoules. Solid and liquids fractions were subjected to thermogravimetric analyses in order to study their combustibility. The gas fraction was analysed by means of gas chromatography to establish the content of CO, CO2, H2 and hydrocarbons present in the samples (mainly components of gases produced in the pyrolysis process). A special study was made of the sulphur and chlorine content of all the fractions, as the presence of these elements could be problematic if the products are used as fuel. Tyre pyrolysis engenders a solid carbon residue that concentrates sulphur and chorine, with a relatively high calorific value, although not so high as that of the original tyre. The liquid fraction produced by the process has a high calorific value, which rises with the final temperature, up to 40 MJ/kg. The chlorine content of this fraction is negligible. Over 95% of the gas fraction, regardless of the final temperature, is composed of hydrocarbons of a low molecular weight and hydrogen, this fraction also appearing to be free of chlorine.     

Economic aspects of the rehabilitation of the Hiriya landfill

The Hiriya landfill, Israel's largest, operated from 1952 to 1998. The landfill, located in the heart of the Dan Region, developed over the years into a major landscape nuisance and environmental hazard. In 1998, the Israeli government decided to close the landfill, and in 2001 rehabilitation activities began at the site, including site investigations, engineering and scientific evaluations, and end-use planning. The purpose of the present research is to perform a cost-benefit analysis of engineering and architectural-landscape rehabilitation projects considered for the site. An engineering rehabilitation project is required for the reduction of environmental impacts such as greenhouse gas emissions, slope instability and leachate formation. An architectural-landscape rehabilitation project would consider improvements to the site to make it suitable for future end uses such as a public park. The findings reveal that reclamation is worthwhile only in the case of architectural-landscape rehabilitation of the landfill, converting it into a public park. Engineering rehabilitation alone was found to be unjustified, but is essential to enable the development of a public park.     

Comparative Thermodynamic Study on the Contribution of the Autocondensation and Copolymerization Reactions for the Tannins of the Subspecies of Acacia nilotica

Autocondensation and copolymerization reactions of the Acacia nilotica subspecies tomentosa (Ant) and the subspecies adansonii (Ana) tannins extracts solutions have been studied at several pH values by thermomechanical analyzer. Results of chemical analysis of these tannins revealed that the studied tannins, Ant and Ana contained high percentages of extractable tannins (54 and 57 %) for and polyphenolic materials (78 and 80 %) respectively. Different hardeners such as paraformaldehyde, Urea and pMDI were added at different ratios and their polycondensation reactions was studied and compared with their autocondensation ones. The aim was to evaluate the tannins suitability for the production of commercially and technically viable tannin adhesives with reduced Formaldehyde emission for wood products and to study the interference between the autocondensation and the copolymerization reaction. The obtained results of autocondensation reaction for both of the tannins studied showed that the best Young’s modulus values for Ant (3,500 and 2,750 MPa) and Ana (2,650 and 2,620 MPa) were obtained at pH 5 and 7. The Young’s modulus values obtained by the tannins Ant were higher than those achieved by Ana. This indicates that the Ant is more reactive than Ana. These results were also in line with results achieved by the gel time for both of the tannins. Gel time results indicate that the reactivity of both tannins increased towards alkalinity with Ana being more reactive at alkaline pH. Addition of 8 % of paraformaldehyde was adversely affecting the autocondensation reactions, as the best Young’s modulus values were achieved at pH 4 for Ant tannins. As for Ana the higher Young’s modulus values (2,000 and 2,310 MPa) were achieved at pH 5 and 7. This indicates that autocondensation reaction was contributed to the final network of the copolymerization reaction. When smaller ratio of paraformaldehyde and Urea (5 %) was added to Ant tannins it favors the autocondensation reaction and the best Young’s modulus values were obtained at pH 5 and 7. Addition of pMDI (10–30 %) was found to decrease the temperature of copolymerization and the obtained Young’s modulus values by Ant were lower than those obtained by autocodensation reaction. Best Young’ modulus values were obtained by Ant at pH 5 and 7. Ana gave the best Young’s modulus values at pH 4 and 5 indicating that the autocondensation appears to depress the copolymerization reactions. The obtained results by both reactions were very important from technical and economical point of view as they concluded that it is very possible to produce adhesives system with zero emission depending on the tannins autocondensation reaction and pH values. Reduction of formaldehyde emission was also possible upon addition of smaller amount of paraformaldehyde and Urea.     

日本包装废物管理体系和产生特性分析

介绍了日本的资源循环法律体系和促进容器包装分类回收和再商品化的法律和有关方针，介绍了日本容器和包装的管理体制和主要措施，以及各类包装废物回收利用状况和特点。     

A comparison of the comprehensive municipal solid waste management systems of the region of Prague and the principality of Asturias. the influence of collection systems and municipality size on the waste collection and the recycling rates

Journal of Material Cycles and Waste Management - The correct management of municipal solid waste (MSW) is a critical factor in the protection of the environment, as well as a source for the...     

On the Methods for the Delimitation of Seasons

It is well known that air pollution is one of the major factors affecting human health and the activities in a town. Among the various air pollutants an interesting one, especially for sunny climates, is the reactive O₃. O₃ varies significantly through the year; it is therefore very important to know the onset and the duration of the warm period of the year since at that time O₃ concentrations increase significantly. In this work, an attempt was made to determine the onset of warm season of the year as well as its duration in various sites located in Northeastern Mediterranean. For this purpose, a fuzzy clustering method is used. The method was applied on the isobaric thickness between 1000 and 500 hPa for the period from 1974 to 1997. The results were compared to conventional methods based on synoptic classification and were found to be in good agreement.