电絮凝—超滤组合工艺处理设施农业营养废液的试验研究

设施农业营养废液具有氮和磷营养元素含量高、碳元素少、病原菌多的特点,直接排放会污染环境、影响生态平衡,因此排放前需经过适当净化处理。为此,采用电絮凝—超滤组合工艺对设施农业营养废液进行处理,重点研究了电絮凝—超滤组合工艺对营养废液中污染物的去除效果,同时考察了电流密度和电解时间对处理效果的影响。结果表明,电絮凝—超滤组合工艺对大肠杆菌、总磷、总氮和总有机碳(TOC)都有一定的去除效果,在电流密度为1.78mA/cm2、电解时间为30min、超滤压力为0.16 MPa的条件下,其去除率分别为99.88%、99.76%、47.59%、28.72%。因此,电絮凝—超滤组合工艺对设施农业营养废液有较好的处理效果。     

紫外催化湿式双氧水氧化处理化学镀铜废液

利用化学镀铜废液自身含有的铜作为催化剂，应用紫外催化湿式双氧水氧化工艺处理化学镀铜废液取得了良好效果。通过单因素实验确定的推荐工艺条件为：pH=2.0（保持原始值不变）；不额外投加铜催化剂；H₂O₂用量为2倍理论量。在此条件下处理化学镀铜废液180 min，COD去除率可达到96.6%；之后采用沉淀法回收铜，调节处理后废水pH到9.5，铜的回收率可达到99.8%。     

膜电解工艺处理碱性含铜蚀刻废液

实验对碱性含铜蚀刻废液膜电解工艺处理的可行性开展相关研究,考察了槽电压、电解时间和阳极液pH值等因素对膜电解电流效率的影响,并确定了最佳工艺条件:槽电压3.10 V、电解时间2 h、阳极液初始pH值9.20。在上述最优工艺条件下,膜电解电流效率达91.5%。实验结果表明,该工艺操作方便、简单可行,是处理蚀刻废液、回收铜的有效方法,具有一定的应用价值。     

混凝与芬顿工艺联用处理切削废液

为了处理常规物化和生化工艺难于有效处理的机械加工切削废液,采用了混凝与芬顿工艺联用对其进行降解处理的实验研究。结果表明,混凝与芬顿工艺联用对切削废液有明显的处理效果,尤其是COD和色度的去除率分别可达80.15%和96.88%。同时,比较了混凝/芬顿和芬顿/混凝不同联用方式对切削废液的处理效果,表明了混凝/芬顿工艺联用具有更好的处理效果和更低的运行成本。     

糖蜜酒精废液厌氧生物降解生物化学甲烷势分析

在中温条件下,对pH值和营养比例2个影响因素进行了糖蜜酒精废液的BMP分析,探讨酒精废液在厌氧消化过程中产甲烷量、COD浓度的变化情况,以及COD去除率与产气量、pH值之间的关系.研究结果表明,厌氧处理法能够使糖蜜酒精废液的有机负荷大大降低,COD去除率最高可达90.6%.在调节营养比例的条件下,pH=8.5时甲烷菌活性最佳,其中COD:P=300:1的产甲烷量最高.     

盐酸酸洗废液制备纳米氧化铁

探索了一种盐酸酸洗废液资源化处理的新工艺,采用"负压蒸发+纳米氧化铁制备"组合模式,实现了废液中盐酸的回收及铁盐的综合利用。采用正交实验考察了真空度、反应温度和蒸发量对负压蒸发工艺的影响;然后在最佳负压蒸发工艺操作条件下进行纳米氧化铁的制备,并采用正交实验考察了氨水浓度、Fe~(2+)浓度、反应温度、搅拌速率和煅烧温度等因素对α-Fe_2O_3制备的影响。     

二氧化氯泡沫分离法处理水合肼类废液

采用二氧化氯泡沫分离装置,研究了二氧化氯泡沫分离法对水合肼类废液的处理效果.通过实验重点考察了废水pH值、二氧化氯投加量和反应时间等参数对废水处理效果的影响.在最佳反应条件(即pH值为10,每升废水中二氧化氯的投加量为5 mg/1 000 COD、反应时间为3 h)下进行反应,原废液(COD值为30 000～35 000 mg/L,氨氮总量为2 500～2 700 mg/L)经处理后COD去除率达到99%,氨氮去除率达到96%以上.     

中和-氧化-混凝法联合处理油田酸化废液

针对油田酸化废液成分复杂、处理难度大的问题,在对酸化废液主要污染物进行成分分析的基础上,通过对p H调节工艺、总铁及悬浮物等污染物去除工艺的研究,形成了中和-氧化-混凝-过滤的处理技术。重点研究了药剂种类、投加量、处理时间等因素对酸化废液处理效果的影响,并对工艺参数进行了优化:Na OH与Ca O质量比为3∶1,c(H2O2)=4 000 mg·L~(-1),氧化时间为20 min,c(PAC)=800 mg·L~(-1),c(PAM)=10 mg·L~(-1)。研究结果表明,酸化废液经最佳工艺处理后可达到回注水水质标准:ρ(悬浮物)10 mg·L~(-1)、ρ(油)30 mg·L~(-1)、p H值为6~9、F(腐蚀速率)0.076 mm·a-1。为酸化废液回注处理工艺、装置的设计及现场实施提供了理论依据与指导。     

加盐蒸馏回收盐酸和混凝剂制备技术资源化利用盐酸酸洗废液

为了实现钢材酸洗废液的资源化,能够同时回收盐酸和铁盐,提出了加盐蒸馏回收盐酸与蒸馏母液制备聚铁混凝剂两段组合工艺相结合的技术。实验对质量浓度为9.28%的实际盐酸废液进行了研究,考察了添加盐的种类、盐的投加量和蒸馏量等因素对再生盐酸回收效果和聚铁混凝剂溶液混凝效果的影响。研究表明,氯盐可以明显改变氯化氢、水的相对挥发度,当CaCl2投加量为1 mol/L,体积蒸馏量在30%时,为此工艺的最佳条件。在此工艺条件下,再生盐酸质量浓度约22.3%;蒸馏母液制备得到的聚铁混凝剂溶液应用实验表明,对印染废水脱色效果良好。此工艺不仅实现了酸洗废液中残酸和铁离子的资源化利用,而且达到酸洗废液的零排放。     

模拟含铀废液的除铀方法与效果

受天然铀矿物形成条件的启发,通过改变含铀废液的物理化学条件,即能在含铀废液中形成较稳定沥青铀矿或者其他沉淀物,实现除铀目的。这种除铀方法被定义为沥青铀矿结晶法。在不同的物理化学条件下采用此方法处理了含铀废液,其结果表明,升高温度、降低Eh,除铀速度加快,除铀效率提高,其中,在物理化学条件为T=85℃、p H=3、Eh=+61.1 m V时,铀元素以沥青铀矿的形式从溶液中析出,除铀率高达99.6%,效果良好。     

Recovery of an Aqueous Iron Phosphating/ Degreasing Bath by Ultrafiltration

Aqueous cleaners are emerging as safe and effective alternatives to solvent degreasers, but switching to water-based cleaners may create a new waste which is high in oil and grease and potentially RCRA hazardous. In the case study summarized here, one metal fabricator replaced a trichloroethylene degreaser with an aqueous iron phosphating/degreasing bath to clean and precondition steel parts. The aqueous bath typically lasted three to four months, until the buildup of oil in the tank began to sacrifice product quality and raise oil and grease levels in the rinse water discharge. Hauling away and replacing the spent cleaner resulted in more than 15,000 gallon/year of hazardous waste.

Ultrafiltration was selected as the most promising technology to recycle the aqueous cleaner and thereby reduce hazardous waste generation. Following pilot-scale testing at the Illinois Hazardous Waste Research and Information Center, on-site full-scale testing integrated the new waste reduction scheme directly into the facility’s production process. Ultrafiltration continuously filtered and returned clean process solution back to the iron phosphating/degreasing bath during normal plant operation, substantially reducing and maintaining oil concentrations at acceptable operating levels. The new process design successfully reduced hazardous waste generation 99.8 percent with a payback period of only 6.9 months.     

机械加工业清洁生产的一则技改实例

一家机械加工厂采用先进的工艺和设备代替落后的工艺和设备，并且撤消了一些工序和对生产车间进行了重新布局，不仅提高了工作效率，而且减少了环境污染，促进了清洁生产，对此，从废水，废气，噪声和废渣四个方面进行了详细评述。     

Hazardous Waste Minimization: Part IV Waste Reduction in the Metal Finishing Industry

The metal finishing industry uses over 40 production processes to produce a wide range of metal products. Waste streams generated include wastewater, waste oils, spent solvents, and spent process solutions. Currently a wide variety of techniques which minimize waste are available. Cost-effective methods to reduce electroplating wastewater contamination include water conservation and drag-out reduction, recovery and management. Ways to cost-effectively reduce the generation of spent metal-working fluids include establishing a fluid management program and installing a fluid recovery system. However, before any techniques are selected, a waste reduction survey should first be conducted.     

Towards sets of hazardous waste indicators. Essential tools for modern industrial management

Decision-makers require useful tools, such as indicators, to help them make environmentally sound decisions leading to effective management of hazardous wastes. Four hazardous waste indicators are being tested for such a purpose by several countries within the Sustainable Development Indicator Programme of the United Nations Commission for Sustainable Development. However, these indicators only address the 'down-stream' end-of-pipe industrial situation. More creative thinking is clearly needed to develop a wider range of indicators that not only reflects all aspects of industrial production that generates hazardous waste but considers socio-economic implications of the waste as well. Sets of useful and innovative indicators are proposed that could be applied to the emerging paradigm shift away from conventional end-of-pipe management actions and towards preventive strategies that are being increasingly adopted by industry often in association with local and national governments. A methodological and conceptual framework for the development of a core-set of hazardous waste indicators has been developed. Some of the indicator sets outlined quantify preventive waste management strategies (including indicators for cleaner production, hazardous waste reduction/minimization and life cycle analysis), whilst other sets address proactive strategies (including changes in production and consumption patterns, eco-efficiency, eco-intensity and resource productivity). Indicators for quantifying transport of hazardous wastes are also described. It was concluded that a number of the indicators proposed could now be usefully implemented as management tools using existing industrial and economic data. As cleaner production technologies and waste minimization approaches are more widely deployed, and industry integrates environmental concerns at all levels of decision-making, it is expected that the necessary data for construction of the remaining indicators will soon become available.     

Solid Waste Disposal in the Netherlands

In The Netherlands, a small and densely populated country, the disposal of solid waste requires strict precautions. Because the landscape is flat and the watertable just under groundlevel, landfilling and dumping must be avoided as much as possible. Incineration of municipal and industrial waste are presently under consideration. But even when excellent flue gas cleaning systems are used, air pollution can present a problem, for instance, by dioxines produced during the process. For these reasons the government has published a waste disposal policy plan in which recycling, composting and prevention of waste production play a major role. Eventually about one third of the solid waste production will be incinerated or dumped. No solid waste will be exported.     

酒精企业清洁生产的系统仿真及政策调控

酒精企业的清洁生产涉及到工艺流程的改进、循环冷却水、糟泥等的资源化利用等各方面,是一个复杂的反馈系统.采用系统动力学模型,运用DYNAMO语言,以某酒精制造企业的清洁生产为例进行仿真模拟,通过调控煤炭价格、水资源费、排污费以及沼气、糟泥等的不同利用方式等参数提出优选方案,分析提高该厂在推进清洁生产的不同方案下的经济效益,为该企业实施清洁生产方案的优化提供决策依据,为政府进行政策制定提供相关建议.     

间二硝基苯清洁生产工艺研究

根据清洁生产原理、间二硝基苯生产工艺及废水产生情况,提出了重结晶废水直接回用于精制,精制废水蒸馏后回用于精制洗涤和重结晶的清洁生产工艺;经小试4次和中试3次废水循环套用后产品均为优等品,证明清洁生产工艺对产品质量无不良影响,可实现工艺废水零排放。     

化工项目环境影响评价要点

化工项目的环境影响评价应严格执行有关的法律、法规和导则,并结合行业特点执行特定的条例和规范。在其评价过程中应确保工程分析数据的可靠性和措施的可行性,对是否符合清洁生产进行详细阐述,针对事故风险进行评价并提出防范措施,最后对有毒废渣的处理提出要求。     

中国固体废物法规体系框架分析

固体废物污染与其它环境污染不同,具有综合性、长期性和潜在性。固体废物管理更为强调综合利用和全过程管理,必须通过立法建立科学完善的法律制度来加强固体废物的管理。有关固体废物污染防治的法律、法规、部门规章、地方法规和环境技术标准构成了固体废物法规体系的基本框架。在系统分析现有固体废物法规中存在的问题的基础上,对固体废物管理的法规框架进行了探讨。通过立法,以“统一协调,分工负责”的原则规范各部门对固体废物的管理职能。还强调通过立法、健全监督机制、从法律上限制个人对行政权的滥用、制订技术政策与环境技术标准。除了行政责任外,论文还着重强调了环境违法者的民事责任和刑事责任。     

日用陶瓷实施清洁生产技术的评价

清洁生产是一个系统工程 ,是对生产全过程以及产品的整个生命周期采取污染预防的综合措施。采用LCA的方法对日用陶瓷生产过程进行全面分析与评价 ,并提出了实施清洁生产的途径。