不同含水率煤尘在瓦斯爆炸诱导下爆炸传播规律研究

为了探究不同含水率煤尘在瓦斯爆炸诱导下的爆炸传播规律,利用自行搭建的直管瓦斯爆炸诱导煤尘二次爆炸实验系统,从冲击波压力和火焰传播速度2个方面,研究了不同含水率沉积煤尘在瓦斯爆炸诱导下的爆炸传播规律和原因。研究结果表明:当煤尘含水率小于40%时,管道内沉积煤尘会在瓦斯爆炸诱导下产生二次爆炸,同时沉积煤尘总量一定时,沉积煤尘二次爆炸产生的冲击波超压峰值和火焰传播速度随着煤尘含水率的增加先增大后减小;当沉积煤尘含水率为20% 时,煤尘二次爆炸产生的冲击波超压峰值、火焰传播速度峰值达到最大值,分别为1.657 MPa和468.060 m/s;当沉积煤尘含水率大于40%时,沉积煤尘无法产生二次爆炸,此时爆炸产生的威力小于单一瓦斯爆炸,火焰传播速度衰减较无煤尘的瓦斯爆炸更快,沉积煤尘起到抑制瓦斯爆炸传播的作用。研究结果可以为防治煤尘二次爆炸提供理论依据。     

Flammability limit measurements for dusts in 20-L and 1-m3 vessels

Two types of flammability limits have been measured for various dusts in the Fike 1-m³ (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m³ vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1-m³ vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.     

小苏打对红色彩跑粉粉尘云爆炸极限氧浓度的影响*

为研究彩跑粉的爆炸强度和爆炸敏感性,采用20 L球形爆炸实验系统和热重-差热分析仪开展实验,在分析红色彩跑粉爆炸压力和爆炸极限氧浓度(LOC)的基础上,进一步揭示小苏打对红色彩跑粉爆炸极限氧浓度的影响规律。研究结果表明:在玉米粉中添加红色食用色素后形成的彩跑粉会增加爆炸风险,爆炸猛烈度属于St1级;在50~400 g/m3粉尘浓度范围内,红色彩跑粉的LOC值先减小后增大,在200 g/m3时LOC值达到最低9%;当添加不同比例小苏打对红色彩跑粉爆炸风险进行抑制时,发现LOC值随着红色彩跑粉与小苏打混合性粉尘掺混比的增大而增大,在掺混比为50%时,红色彩跑粉与小苏打混合性粉尘的LOC值为21%。研究结果可为彩跑粉加工厂的抑爆和惰化防爆技术提供基础数据参考。     

Explosion characteristics of micron- and nano-size magnesium powders

Explosion characteristics of micron- and nano-size magnesium powders were determined using CSIR-CBRI 20-L Sphere, Hartmann apparatus and Godbert-Greenwald furnace to study influence of particle size reduction to nano-range on these. The explosion parameters investigated are: maximum explosion pressure (P_max), maximum rate of pressure-rise (dP/dt)_max, dust explosibility index (K_St), minimum explosible concentration (MEC), minimum ignition energy (MIE), minimum ignition temperature (MIT), limiting oxygen concentration (LOC) and effect of reduced oxygen level on explosion severity. Magnesium particle sizes are: 125, 74, 38, 22, 10 and 1 μm; and 400, 200, 150, 100, 50 and 30 nm. Experimental results indicate significant increase in explosion severity (P_max: 7–14 bar, K_St: 98–510 bar·m/s) as particle size decreases from 125 to 1 μm, it is maximum for 400 nm (P_max: 14.6 bar, K_St: 528 bar·m/s) and decreases with further decrease of particle size to nano-range 200–30 nm (P_max: 12.4–9.4 bar, K_St: 460–262 bar·m/s) as it is affected by agglomeration of nano-particles. MEC decreases from 160 to 30 g/m³ on decreasing particle size from 125 to 1 μm, its value is 30 g/m³ for 400 and 200 nm and 20 g/m³ for further decrease in nano-range (150–30 nm). MIE reduces from 120 to 2 mJ on decreasing the particle size from 125 to 1 μm, its value is 1 mJ for 400, 200, 150 nm size and <1 mJ for 50 and 30 nm. Minimum ignition temperature is 600 °C for 125 μm magnesium, it varies between 570 and 450 °C for sizes 38–1 μm and 400–350 °C for size range 400–30 nm. Magnesium powders in nano-range (30–200 nm) explode less violently than micron-range powder. However, likelihood of explosion increases significantly for nano-range magnesium. LOC is 5% for magnesium size range 125–38 μm, 4% for 22–1 μm, 3% for 400 nm, 4% for 200, 150 and 100 nm, and 5% for 50 and 30 nm. Reduction in oxygen levels to 9% results in decrease in P_max and K_St by a factor of 2–3 and 4–5, respectively, for micron as well as nano-sizes. The experimental data presented will be useful for industries producing or handling similar size range micron- and nano-magnesium in order to evaluate explosibility of their magnesium powders and propose/design adequate safety measures.     

运用本质安全原理预防煤粉爆炸

旨在将本质安全原理与粉尘爆炸(以煤粉爆炸为例)的风险控制联系起来。利用20 L球形爆炸装置的标准测试方法测试煤粉及煤粉-CaCO3混合物的爆炸下限、最大爆炸压力、压力上升速度等爆炸特性。基于本质安全基本原理和试验结果,讨论预防煤粉爆炸的各种基本方法,并重点阐述本质安全原理与粉尘爆炸影响因素、不同的预防方法、过程设备的选择等之间的关系,对已制定的爆炸风险控制措施进行完善和补充。     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

Influences of coal dust components on the explosibility of hybrid mixtures of methane and coal dust

In order to study the influences of coal dust components on the explosibility of hybrid mixture of methane and coal dust, four kinds of coal dust with different components were selected in this study. Using the standard 20 L sphere, the maximum explosion pressure, explosion index and lower explosion limits of methane/coal dust mixtures were measured. The results show that the addition of methane to different kinds of coal dust can all clearly increase their maximum explosion pressure and explosion index and decrease their minimum explosion concentration. However, the increase in the maximum explosion pressure and explosion index is more significant for coal dust with lower volatile content, while the decrease in the minimum explosion concentration is more significant for coal dust with higher volatile content. It is concluded that the influence of methane on the explosion severity is more pronounced for coal dust with lower volatile content, but on ignition sensitivity it is more pronounced for coal dust with higher volatile content. Bartknecht model for predicting the lower explosion limits of methane/coal dust mixture has better applicability than Le Chatelier model and Jiang model. Especially, it is more suitable for hybrid mixtures of methane and high volatile coal dust.     

激波诱导下煤粉的爆炸压力测试

因气体爆炸导致沉积粉尘的二次爆炸的威力远大于单纯的气体或者粉尘爆炸产生的威力,利用自制的装置,诱导煤粉爆炸的激波由甲烷气体爆炸产生,对激波诱导下煤粉的爆炸压力Pmax、爆炸压力上升速率(dp/dt)max进行了实验研究。该实验分别研究煤粉浓度及煤粉粒度对爆炸指数的影响,其结果表明:对于不同的煤粉浓度,存在一个理想煤粉浓度值,在这个浓度下的煤粉爆炸压力值最大;随着煤粉粒度的减小,其爆炸压力不断升高。     

Particle size and surface area effects on explosibility using a 20-L chamber

The Mine Safety and Health Administration (MSHA) specification for rock dust used in underground coal mines, as defined by 30 CFR 75.2, requires 70% of the material to pass through a 200 mesh sieve (<75 μm). However, in a collection of rock dusts, 47% were found to not meet the criteria. Upon further investigation, it was determined that some of the samples did meet the specification, but were inadequate to render pulverized Pittsburgh coal inert in the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) 20-L chamber. This paper will examine the particle size distributions, specific surface areas (SSA), and the explosion suppression effectiveness of these rock dusts. It will also discuss related findings from other studies, including full-scale results from work performed at the Lake Lynn Experimental Mine. Further, a minimum SSA for effective rock dust will be suggested.     

Law of variation for low density polyethylene dust explosion with different inert gases

To reveal the effects of different inert gases on explosion characteristics during low density polyethylene (LDPE) dust explosion and optimize the explosion-proof process, eight N₂ (CO₂)/air mixed inerting conditions were experimentally studied. Typical inerting conditions with 12 L cylindrical explosive tank were used to study the characteristics on the flame propagation. The thermogravimetric analysis with related theories were used to further explain the mechanism and quantities in low density polyethylene (LDPE) dust explosion with different inert gases. The results showed that the reduction of O₂ concentration could effectively delay the progress of flame growth process and weaken the effect of dust combustion reaction. The flame growth process of condition (N₂/air (18% O₂)) was 2.05 times slower than that of the non-inert condition. The explosion strength was obviously reduced, and the characteristic parameters such as explosion pressure and flame propagation speed were also affected by the decrease of O₂ concentration. For LDPE powder, the smaller the median diameter, the greater the explosion intensity and the lower the limiting oxygen content (LOC). The LOC with CO₂ was usually higher than that with N₂ and the effect of CO₂ was significantly better than N₂ in inerting.     

管道内瓦斯煤尘共混爆炸温度特性

采用瞬态火焰传播实验系统,对7%,8%,9%,10%和11%的瓦斯体积浓度分别与不同浓度的长焰煤煤尘混合,并使用直径25 μm的Pt/Rh13-Pt微细热电偶测量温度,揭示受限空间内瓦斯与煤尘混合爆炸温度特性。结果表明:煤尘浓度一定时,随着瓦斯浓度的增加,爆炸温度先增加后减小;纯瓦斯浓度在10%时爆炸温度最高,加入煤尘后的混合体系中,瓦斯浓度为9%时爆炸温度最高;瓦斯浓度不变时,随着煤尘浓度的增加,爆炸温度一直减小;7%~11%瓦斯分别与130 g/m3煤尘混合爆炸后测得最高温度分别为1 333.6,1 475.4,1 511.4,1 455.6,1 396.4 ℃;与9%纯瓦斯爆炸相比,9%瓦斯与130,260,520,780 g/m3煤尘混合爆炸后测得最高温度分别降低7.2%,11.5%,15.0%和22.9%。结论得到的瓦斯煤尘共混爆炸温度数据可为煤矿灾害高温防护提供参考依据。     

煤尘挥发分及粒径对爆炸火焰长度的影响研究

为研究煤尘挥发分及粒径对爆炸火焰长度的影响及其变化规律,选取挥发分含量不同的四种典型烟煤煤样,分别制备成31.5、44、62.5、81.5、119、>150 μm六种粒径,利用煤尘爆炸性鉴定装置测试其爆炸火焰长度,并对其爆炸火焰长度变化规律进行分析。结果表明:随着挥发分含量的增加,不同粒径级别的煤尘爆炸火焰长度均呈增长趋势;在挥发分含量较低的区间,挥发分含量增加对爆炸火焰长度影响不大;在挥发分含量较高的区间,随着挥发分含量的增加其爆炸火焰长度也急剧增加,并且粒径越小增加的越快。对于同一实验煤样,随着粒径的增大,其爆炸火焰长度逐渐减小,粒径增大到150 μm以上时爆炸火焰几乎消失。爆炸火焰长度随粒径变化的变化率根据实验煤样的不同,呈现出两种变化规律,挥发分含量为18.99%和27.52%煤样的爆炸火焰变化率先增加再减小再增加,挥发分含量为32.20%和39.74%的煤样呈现先增加再减小的趋势,但四组实验煤样的爆炸火焰长度变化率都在44～62.5 μm的粒径变化量时达到最大值。     

影响煤粉挥发分析出量的因素探讨

煤粉爆炸实质上是挥发分可燃气体与空气混合而形成的爆炸,挥发分析出的多少对煤粉的爆炸有重要的影响,因此研究挥发分析出量的影响因素很有必要.取兖州烟煤做实验,讨论了空气干燥基挥发分V ad随磨制时间、环境温度、煤粉粒度等的变化规律,以及挥发分析出温度与粒度的关系.根据规律,提出可以科学地控制这些因素以更好地实现电厂煤粉的防爆.     

氧气厂重大危险源辨识和安全管理

对氧气厂液氧储罐区和氧气球罐区进行了重大危险源辨识,分析了氧气球罐发生物理爆炸的影响范围,提出了液氧储罐区和氧气球罐区预防事故的安全对策措施,并对重大危险源管理提出了建议.     

瓦斯爆炸引起沉积煤尘爆炸传播实验研究

运用井下大型实验巷道对瓦斯爆炸诱导沉积煤尘爆炸进行实验研究,并对几次实验结果进行对比分析。通过对爆炸压力以及火焰产生、发展、传播过程进行的分析,得出瓦斯爆炸引起沉积煤尘爆炸过程中压力波存在回传现象;在煤尘刚开始参与爆炸处,爆炸超压有一个较长的持续时间;爆炸火焰的传播速度在铺有煤尘段迅速上升,最后有一平缓的上升阶段,过了煤尘段开始下降;火焰区长度约为煤尘区长度的2倍等规律。实验研究发现的规律为有效的预防瓦斯煤尘爆炸事故提供了理论依据。     

硬脂酸粉尘爆炸特性试验研究

为研究硬脂酸粉尘的爆炸特性,采用20 L球型爆炸仪对4个粒径范围的硬脂酸粉尘进行粉尘爆炸试验研究。结果表明:一定浓度范围内增大粉尘浓度能够提升硬脂酸粉尘的爆炸能量和燃烧速率。增大粉尘浓度,爆炸猛烈度先增强后减弱;减小粉尘粒径,能增强爆炸猛烈度和敏感度。粒径小于58 μm粉尘的爆炸猛烈度和敏感度最大,浓度500 g/m3时,该粉尘有最大爆炸压力1.12 MPa和最大升压速率142.00 MPa/s。     

不同磁化抑尘剂对煤粉润湿性影响规律的实验研究

针对微小粒径粉尘具有危害大且难润湿的问题,基于润湿剂与磁场对水滴颗粒的耦合改性机理,研究不同磁场强度下各抑尘剂对煤粉润湿性影响,采用座滴法测定磁化试剂的煤粉表面接触角,通过粉尘润湿机理进行分析,煤尘沉降Walker实验进行佐证,得到抑尘剂种类、浓度与磁化强度对煤粉的润湿性规律。结果表明:未经磁化的高于临界胶束浓度值溶液对煤尘的润湿能力变化不大,阴离子表面活性剂溶液对煤样的润湿能力强于非离子表面活性剂溶液和阳离子表面活性剂溶液;磁化强度为500 mT的磁化溶液对煤尘润湿能力达到最佳效果。     

散煤运输用膜型抑尘剂的制备及性能研究

采用水溶液聚合法,以氧化淀粉、丙烯酸(AA)、二甲基二烯丙基氯化铵(DMDAAC)为原料,通过接枝共聚制备了一种软膜型抑尘剂(抑尘剂液体干燥后形成具有一定韧性的软膜)。与聚乙烯醇类壳型抑尘剂(干燥后形成很脆的壳层)相比,软膜型抑尘剂提高了煤粉固化层的抗破裂能力。由抗震荡性试验可知,使用膜型抑尘剂后,经过18 h的震荡,煤粉的损失率仅为1.91%,而使用壳型抑尘剂后煤粉的损失率为4.85%。还测定了2种抑尘剂的保湿性和耐破度。利用红外光谱对产物的结构进行了表征,采用SEM观察了该产物在煤粉表面形成的膜层形貌。试验结果表明,散煤运输中膜型抑尘剂在减少煤粉损失和控制扬尘污染方面性能优于壳型抑尘剂。     

固体惰性介质对煤粉爆炸压力的影响研究

通过对固体惰性介质在减轻煤粉爆炸作用的实验研究,给出影响固体惰化剂作用效果的主要影响因素。实验分别选用来自加拿大和中国的3种煤粉和石灰石,对每种实验样品的成分、粒度都进行分析。用20L球形容器进行实验,测定煤粉中加入不同含量的石灰石后煤粉爆炸的Pmax和(dp/dt)max值。结果表明,石灰石能够起到减轻煤粉爆炸影响的作用,并且随着煤粉粒度的减小,要达到相同的抑爆效果需要的石灰石的用量将加大。     

R290制冷剂惰化燃爆特性实验研究

为了研究R290制冷剂惰化燃爆特性,采用带搅拌功能和氧浓度在线测定的20L球试验装置,对R290制冷剂进行了极限氧浓度测定。实验测定了丙烷在CO2和N2惰化气氛中的爆炸极限及极限空气浓度LAC,确定丙烷的极限氧浓度LOC;采用三元图爆炸区、丙烷-O2二维图爆炸区和ASTM标准分布图分析了混合气体爆炸区边界的燃爆特征,给出了极限氧浓度的确定方法和边界爆炸压力分布规律。实验结果表明:常温常压下R290的爆炸极限为2.1%～9.6%,CO2惰化气氛中的极限氧浓度为13.3%,对应的丙烷浓度为3.3%;N2惰化气氛中的极限氧浓度为10.8%,对应的丙烷浓度为2.7%。通过对比分析不同CO2和N2浓度下的爆炸区分布特征,表明CO2对丙烷的惰化效果要优于N2,以氮气和二氧化氮体积分数比为1∶2测试惰化气氛保护能力,惰化效果介于同浓度单种惰性气体之间。