Linear free energy relationships for dechlorination of aromatic chlorides by Pd/Fe

Reductive dechlorination rate constants for five chlorobenzenes in the presence of Pd/Fe as catalyst were determined experimentally. Linear free energy relationships (LFER) for the dechlorination rate constants of five chlorobenzenes and three chlorophenols were developed by partial least squares (PLS) regression based on quantum chemical parameters computed by PM3 Hamiltonian. The optimal LFER model obtained is

logk=−1.63+1.46×10⁻³ΔH_f−7.69×10⁻¹E_LUMO

where k stands for the dechlorination rate constants, ΔH_f is the standard heat of formation, and E_LUMO is the energy of the lowest unoccupied molecular orbital. The Q²_cum value of the model is 0.879, indicating good robustness and predictive power of the model.     

Kinetics of nitromusk compounds degradation in water by ultraviolet radiation and hydrogen peroxide

The photodegradation of five representative nitromusk compounds in water has been performed in a stirred batch photoreactor with a UV low-pressure immersed mercury lamp, at constant temperature and different doses of hydrogen peroxide. The rate constants have been calculated on the basis of experimental data and a postulated first-order kinetic model. The rate constants, at 298 K and a dose of 1.1746 μmol l⁻¹ H₂O₂ ranges from 0.3567 × 10⁻³ s⁻¹ for musk tibetene, to 1.785 × 10⁻³ s⁻¹ for musk ambrette.     

Speciation and quantification of vapor phases in soy biodiesel and waste cooking oil biodiesel

This study characterizes the compositions of two biodiesel vapors, soy biodiesel and waste cooking oil biodiesel, to provide a comprehensive understanding of biodiesels. Vapor phases were sampled by purging oil vapors through thermal desorption tubes which were then analyzed by the thermal desorption/GC/MS system. The results show that the compounds of biodiesel vapors can be divided into four groups. They include methyl esters (the main biodiesel components), oxygenated chemicals, alkanes and alkenes, and aromatics. The first two chemical groups are only found in biodiesel vapors, not in the diesel vapor emissions. The percentages of mean concentrations for methyl esters, oxygenated chemicals, alkanes and alkenes, and aromatics are 66.1%, 22.8%, 4.8% and 6.4%, respectively for soy biodiesel, and 35.8%, 35.9%, 27.9% and 0.3%, respectively for waste cooking oil biodiesel at a temperature of 25 ± 2 °C. These results show that biodiesels have fewer chemicals and lower concentrations in vapor phase than petroleum diesel, and the total emission rates are between one-sixteenth and one-sixth of that of diesel emission, corresponding to fuel evaporative emissions of loading losses of between 106 μg l⁻¹ and 283 μg l⁻¹. Although diesels generate more vapor phase emissions, biodiesels still generate considerable amount of vapor emissions, particularly the emissions from methyl esters and oxygenated chemicals. These two chemical groups are more reactive than alkanes and aromatics. Therefore, speciation and quantification of biodiesel vapor phases are important.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

Copper complexation by tannic acid in aqueous solution

The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon (OC)/l was investigated in a nine-step titration experiment (Cu/OC molar ratio = 0.0030–0.0567). We differentiated between soluble and insoluble Cu species by 0.45 μm filtration. Measurements with a copper ion selective electrode (ISE) and diffusive gradients in thin films (DGT) were conducted to quantify unbound Cu(II) cations (‘free’ Cu) and labile soluble Cu complexes. For the DGT measurements, we used an APA hydrogel and a Chelex 100 chelating resin (Na form). Insoluble organic Cu complexes (>0.45 μm) was the dominant Cu species for Cu/OC = 0.0030–0.0567 with a maximum fraction of 0.96 of total Cu. At Cu/OC > 0.0100, Cu-catalysed degradation of aggregate structures resulted in a strong increase of free Cu and (labile) soluble Cu complexes with a maximum fraction of 0.28 and 0.32 of total Cu, respectively. Labile (i.e. DGT-detectable) soluble Cu complexes had a relatively high averaged diffusion coefficient (D) in the APA hydrogel (3.50 × 10⁻⁶– 5.58 × 10⁻⁶ cm² s⁻¹).     

Leaching of atrazine, metolachlor and diuron in the field in relation to their injection depth into a silt loam soil

A field experiment was conducted on a Calcaric Cambisol soil to study the consequences of the penetration depth and properties of pesticides on the risk of subsequent leaching. Three pesticides with different mobility characteristics and bromide were injected at 30 cm (where soil organic matter (OM) was 2%) and 80 cm (soil OM 0.5%) on irrigated plots without a crop. The migration of injected solutes was assessed for two years by sampling the soil solution using six porous cups installed at 50 and 150 cm depth and by relating solute contents to drainage water flux estimated by the STICS model (Simulateur mulTIdisciplinaire pour les Cultures Standard). Pesticides injected at 30 cm were strongly retained so that no metolachlor or diuron was detected at 50 and 150 cm. The ratio of atrazine peak concentration in the soil solution to concentration in the injected solution (C/C₀) was 1 × 10⁻³ and 0.2 × 10⁻³, respectively, at 50 and 150 cm. When injected at 80 cm, (C/C₀) of atrazine, metolachlor and diuron were 10 × 10⁻³, 1 × 10⁻³ and 0.3 × 10⁻³ at 150 cm, respectively; 1/(C/C₀) was correlated with K_oc values reported from databases. The ratio of drainage volume to the amount of water at field capacity in the soil layer between the injection point at 30 cm and the water sampling level (V/V₀) at 50 and 150 cm was 0.6 and 0.9, respectively, for bromide and 1.6 and 1.0 for atrazine. V/V₀ of the injected solutes at 80 cm was for bromide, atrazine, metolachlor and diuron 0.6, 0.9, 1.2 and 1.7, respectively; pesticide V/V₀ was correlated with K_oc. The retardation factor was a good indicator of migration risk, but tended to overestimate retardation of molecules with high K_oc. Atrazine desorption represented an additional leaching risk as a source of prolonged low contamination. The large variability in soil solution of bromide and pesticide concentrations in the horizontal plane was attributed to flow paths and clods in the tilled soil layer. This heterogeneity was assumed to channel water fluxes into restricted areas and thereby increase the risk of groundwater contamination. The methodology used in the field proves to provide consistent results.     

Determination of vapour pressures of nine organic chemicals adsorbed on silicagel

The vapour pressures of nine organic chemicals adsorbed on silicagel were determined by a method which can be standardized. They were compared with those of the non-absorbed, free compounds (range 6 × 10⁻³ – 7 × 10⁴ Pa).     

Concentrations of chlorine, bromine and iodine in Japanese rivers

Concentrations of halogens (Cl, Br and I) in 30 Japanese rivers were measured by ion chromatography and inductively coupled plasma mass spectrometry to understand their behavior in the terrestrial environment. Concentrations of Cl, Br and I in each river, obtained at 10 sampling points from the upper stream to the river mouth, tended to increase near the river mouth. The ranges of geometric means of Cl, Br and I in each river were 1.0–19.4 mg l⁻¹, 2.5–67.9 μg l⁻¹, and 0.18–8.34 μg l⁻¹, respectively. To compare halogen behavior, the concentration ratios, Br/Cl and I/Cl, were calculated. The Br/Cl range was (2.3–7.8) × 10⁻³ (geometric mean: 3.74 × 10⁻³), and it was nearly constant except for the Yoneshiro river. It was estimated that 60–80% of total Br in the middle to lower parts of this river was the excess Br. The Br chemical form in all the rivers is generally considered to be Br⁻. The I/Cl ratios had different trends in rivers flowing into the Japan Sea and Pacific Ocean, possibly due to the different geological features in the river catchments.     

Vapour pressures, aqueous solubility, Henry's law constants and air/water partition coefficients of 1,8-dichlorooctane and 1,8-dibromooctane

New data on the vapour pressures and aqueous solubility of 1,8-dichlorooctane and 1,8-dibromooctane are reported as a function of temperature between 20 °C and 80 °C and 1 °C and 40 °C, respectively. For the vapour pressures, a static method was used during the measurements which have an estimated uncertainty between 3% and 5%. The aqueous solubilities were determined using a dynamic saturation column method and the values are accurate to within ±10%. 1,8-Dichlorooctane is more volatile than 1,8-dibromooctane in the temperature range covered (p_sat varies from 3 to 250 Pa and from 0.53 to 62 Pa, respectively) and is also approximately three times more soluble in water (mole fraction solubilities at 25 °C of 5.95 × 10⁻⁷ and 1.92 × 10⁻⁷, respectively). A combination of the two sets of data allowed the calculation of the Henry’s law constants and the air water partition coefficients. A simple group contribution concept was used to rationalize the data obtained.     

锡冶炼含砷烟尘低温陶瓷固化技术

以锡冶炼过程中排放的含砷烟尘为研究对象,对浸出特性和低温陶瓷胶凝材料对其的固化效果进行了研究。结果表明,含砷烟尘As、Cu和Zn毒性浸出浓度分别为6 783、167和224 mg/L,严重超过国家毒性浸出鉴别标准值。其经低温陶瓷胶凝材料固化处理,当含砷烟尘掺量小于40%,自然养护3 d,As、Cu和Zn毒性浸出浓度急剧降低,且低于国家标准值。XRD和SEM分析表明,低温陶瓷胶凝材料在复合化学激发剂作用下,反应生成类沸石水化铝硅酸盐矿物(Al-O-Si);固化体中Ca-Fe-As-O盐是As固化的主要矿物相。Cu2+、Zn2+替换铝硅酸盐聚合物结构中的Na+、K+保持平衡电荷。胶凝材料水化产物填充于材料颗粒间,使其连接成一致密整体,有效降低了有害物质的毒性浸出浓度。     

Cold season CH4, CO2 and N2O fluxes from freshwater marshes in northeast China

Cold season (winter and thaw) CH₄, CO₂ and N₂O fluxes from freshwater marshes (47°35′N, 133°31′E, Northeast China) were measured, using the static chamber method. The mean CH₄ and CO₂ fluxes from Carex lasiocarpa (Cl) were 0.5 ± 0.19 and 6.23 ± 1.36 mg C m⁻² h⁻¹, respectively, and those from Deyeuxia angustifoli (Da) were 0.18 ± 0.15 and 5.22 ± 2.48 mg C m⁻² h⁻¹, respectively in winter. There was no significant difference between Cl and Da (p > 0.05). The contributions of winter CH₄ fluxes were about 5.5% and 3% in the Cl and Da, respectively. Marshes are an important potential N₂O sink in winter season in northeast China. During thaw, the CH₄ and CO₂ emissions rapidly increased, 4.5–6 times of winter emissions. Wetland became a source of N₂O. Cold season gases flux from northern wetlands play an important role in the seasonal gas exchange.     

As(V) adsorption on amorphous iron oxide: Triple layer modelling

The adsorption of As(V) by amorphous iron oxide was investigated at 25°C, 0.01 M NaNO₃ background electrolyte as a function of solution pH(4–10) at three initial As(V) concentrations and two Fe(III) concentrations. As(V) adsorption increased with decreasing pH. A modified Langmuir isotherm has been used for describing an equilibrium partition existing between solid and liquid phases. The triple-layer model was used for simulating As(V) adsorption on iron oxide surface. This model was able to describe As(V) adsorption over the pH range 4–10, all at the concentrations of As(V) and Fe(III) studied. =Fe(H₂AsO₄)⁰, = Fe(HAsO₄)⁻ and = Fe(AsO₄)²⁻ have been shown through simulation with inner-sphere complexation products to be more consistent with experimental adsorption observations than complexation with other surface species.     

An investigation of adsorption at the air-water and soil-water interfaces for non-micellizing ethylene oxide-propylene oxide surfactants

Adsorption at the air–water interface and soil sorption from aqueous solution have been investigated for a group of ethylene oxide (EO)–propylene oxide (PO) block copolymeric surfactants. The group which have a common structural formula of EO_m PO_n EO_m is distinguished by the fact that they have large critical micelle concentration (CMC) values and therefore do not readily form micelles at common environmental concentrations and temperatures. Adsorption at the air–water interface is readily shown to be driven by the size of the hydrophobic PO block. The size of the reduction in surface tension produced by a common concentration of 10⁻⁵ mol dm⁻³ linearly increases with the size of the PO block as does the efficiency of adsorption at the air–water interface as measured by pC₂₀ – the negative logarithm of the surfactant concentration that produces a reduction in surface tension of 20 mN m⁻¹. Soil sorption data have also been captured for these compounds and the data are readily fitted to the Freundlich adsorption isotherm. However soil sorption is shown to be inversely related to the molecular mass of the molecules and appears to be related to the size of the hydrophilic EO blocks in the molecule.     

Effects of selected metal oxides on the dechlorination and destruction of PCDD and PCDF

OCDD and OCDF spiked silica/graphite based model fly ash containing various copper compounds and metal oxides were thermally treated under oxygen deficient conditions. All copper compounds tested showed a considerable dechlorination/hydrogenation reaction at 260 °C. After 30 min at 340 °C, less than 1% of the spiked OCDD and OCDF was recovered as T₄CDD/F to OCDD/F. Other compounds tested demonstrated a lower rate of dechlorination compared to the copper compounds. However, all other metal oxides showed a small dechlorination effect at 260 °C, which was considerably increased at 340 °C.

The model fly ash containing the different copper compounds or metal oxides showed comparable PCDD and PCDF isomer patterns after thermal treatment. However, small differences were observed among the different tested compounds. The PCDD and PCDF isomer patterns on the model fly ashes were similar to patterns found during dechlorination experiments on fly ashes from waste incineration processes.

Model fly ash containing Ca(OH)₂ exhibited the highest destruction potential, but a low dechlorination potential. In contrast, model fly ash containing any of the remaining compounds tested, was found to predominantly dechlorinate the spiked OCDD and OCDF.     

Short-term toxicity of pyraclofos used as a blackfly larvicide on non-target aquatic fauna in a tropical environment

Among the many larvicides tested for the control of s.l. larvae, the vector of human onchocerciasis in West Africa, pyraclofos proved to be 100% effective at 100 μg × L⁻¹ for 10 min in river, with a carry of 20 km at 100 m³ × sec⁻¹. Tests were then performed both in laboratory and field conditions to evaluate its toxicity on the non-target aquatic fauna. In experimental short-term gutter tests, the detachment of the total benthic insects was 35% at 100 μg × L⁻¹ for 10 min against 17% for temephos at the same dose and 59% for chlorphoxim at 50μg × L⁻¹ for 10 min. , and were the most affected organisms. The treatment of a river resulted in a considerable detachment of the same taxonomic groups, plus Orthocladiinae. On the other hand, investigations conducted in tanks showed that the 24-hr LC₅₀ for is 150 μg × L⁻¹ and that for 170 μg × L⁻¹, values which are not very different from the operational dose of the larvicide (100 μg × L⁻¹ for 10 min.). Nevertheless, in a river, no fish mortality was recorded. Based on fish LC₅₀ and drift of benthic insects, pyraclofos at 100 μg × L⁻¹ was judged to be less toxic to aquatic fauna in the short term than permethrin and carbosulfan.     

Specific biomagnification of polychlorinated dibenzo-p-dioxins and dibenzofurans in tufted ducks (Aythya fuligula), common cormorants (Phalacrocorax carbo) and their prey from Lake Shinji,Japan

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/DFs) were detected in waterfowl such as common cormorants, tufted ducks, and their prey, namely fish and bivalves from Lake Shinji, Japan. The concentration of total PCDDs/DFs-TEQ was found to be higher in the muscle tissues of common cormorants than in those of tufted ducks. The results of hierarchical cluster analysis implied that the residue distribution pattern of PCDD/DF homologues was considerably different between these two species. Furthermore, biomagnification factors (BMFs) were estimated from bivalves as prey to tufted duck muscles as target organs. Despite the highest concentrations of 1,3,6,8- and 1,3,7,9-TeCDD in tufted ducks and their prey, however, the BMFs of these isomers were calculated to be lower than those of the toxic 2,3,7,8-substituted PCDDs/DFs. On the other hand, log BMF of toxic 2,3,7,8-substituted PCDDs/DFs were significantly higher for lower chlorinated isomers than those of the higher chlorinated isomers. The biota-sediment accumulation factors (BSAFs) of PCDDs/DFs were also estimated using shijimi clam and fish samples against sediment from Lake Shinji. The average BSAFs were estimated and ranged from 4.0×10⁻³ to 2.2×10⁻¹ and 2.0×10⁻⁴ to 2.0×10⁻¹ for bivalve and fish samples, respectively. Based on calculated BMFs and BSAFs, the total PCDD/DF-TEQ levels in the tufted duck were estimated to have been lowest (2.0 pg TEQ/g dry weight basis) in 1947 and highest (9.8 pg TEQ/g) in 1971.     

Removal of a cationic dye from aqueous solutions by adsorption onto bentonite clay

The ability of bentonite to remove malachite green from aqueous solutions has been studied for different adsorbate concentrations by varying the amount of adsorbent, temperature, pH and shaking time. Maximum adsorption of the dye, i.e. >90% has been achieved in aqueous solutions using 0.05 g of bentonite at a pH of 9. Thermodynamic parameters such as ΔH°, ΔS° and ΔG° were calculated from the slope and intercept of the linear plots of ln K_D against 1/T. Analysis of adsorption results obtained at 298, 308, 318 and 328 K showed that the adsorption pattern on bentonite seems to follow the Langmuir, Freundlih and D–R isotherms. The temperature increase reduces adsorption capacity by bentonite, due to the enhancement of the desorption step in the mechanism. The numerical values of sorption free energy (E_a) of 1.00–1.12 kJ mol⁻¹ indicated physical adsorption. The kinetic data indicated an intraparticle diffusion process with sorption being first order. The rate constant k was 0.526 min⁻¹. The concentration of malachite green oxalate was measured before and after adsorption by using UV–Vis spectrophotometer.     

Determination of 99Tc deposited on the ground within the 30-km zone around the Chernobyl reactor and estimation of 99Tc released into atmosphere by the accident

Technetium-99 was determined in samples from the 30-km zone around the Chernobyl reactor. Concentrations of ⁹⁹Tc in soil samples taken from three forest sites ranged from 1.1 to 14.1 Bq kg⁻¹ dry weight for the organic soil layers, and from 0.13 to 0.83 Bq kg⁻¹ dry weight for the mineral soil layers. In particular, for the organic layers, the measured ⁹⁹Tc concentrations were one or two orders of magnitude higher than those due to global fallout ⁹⁹Tc. The ⁹⁹Tc depositions (Bq m⁻²), based on the sum of the depositions measured in organic and mineral layers, ranged from 130 Bq m⁻² within the 10-km zone to about 20 Bq m⁻² close to the border of the 30-km zone. Taking the corresponding measured ¹³⁷Cs depositions into account, it was found that the activity ratio of ⁹⁹TW/¹³⁷Cs ranged from 6 × 10⁻⁵ to 1.2 × 10⁻⁴. It was estimated that about 970 GBq of ⁹⁹Tc had been released by the Chernobyl accident. This figure corresponded to 2%–3% of the total ⁹⁹Tc inventory in the core.     

Qualitative and quantitative cancer risk assessment of 2, 3, 7, 8-tetrachloro-dibenzo-p-dioxin (2, 3, 7, 8-TCDD)

The carcinogenicity of 2,3,7,8-TCDD at multiple organ sites in animals has been well established by several cancer bioassays. Results of two of the most notable of these, the Kociba et al. (1978) rat feeding study and the National Toxicology Program (1980) gavage study in rats and mice showed hepatocellular carcinomas in two strains of female rats and male and female mice. Other tumor sites included carcinomas of the lung, tongue, hard palate and nasal turbinates, thyroid, and subcutaneous tissue. The evidence for carcinogenicity of 2,3,7,8-TCDD in animals is regarded as “sufficient” using the classification system of the International Agency for Research on Cancer (IARC).

Two Swedish epidemiologic case-control studies (Hardell and Sandstrom, 1979; Eriksson et al. 1979, 1981) reported a significant five- to sevenfold excess risk of soft-tissue sarcomas (STS) from occupational exposure to chlorinated phenoxyacetic acid herbicides and/or chlorophenols. Additionally, several small cohort studies collectively exhibited an unusual cluster of STS, significantly increased over combined expected incidence. Problems with these studies do not appear to be sufficient to discount this excess risk. The human evidence alone for the carcinogenicity of 2,3,7,8-TCDD is “inadequate” using the IARC classification. However, for 2,3,7,8-TCDD in combination with chlorinated phenoxyacetic acid herbicides and/or chlorophenols, the human evidence is considered to be “limited.” The overall evidence for carcinogenicity considering both animal and human studies would place 2,3,7,8-TCDD alone in the IARC category 2B, meaning that the substance is probably carcinogenic in humans. The overall weight of evidence for 2,3,7,8-TCDD in combination with chlorinated phenoxyacetic acid herbicides and/or chlorophenols is regarded as IARC category 2A, also meaning that they are probably carcinogenic for humans.

Using current EPA methodology for quantitatively estimating cancer risks, several animal data sets have been analyzed. Comparing the results, the upper-limit incremental unit risk estimate is 1.6 × 10⁻² for a lifetime exposure of 1 ng/kg/day. This estimate is derived from a lifetime feeding study (Kociba et al., 1978) in which 2,3,7,8-TCDD induced tumors of the liver, lungs, hard palate, and nasal turbinates in female rats. Incremental unit cancer risks are also extrapolated for lifetime 2,3,7,8-TCDD exposures in water and air. Based on continuous lifetime exposure to 1 ng/L 2,3,7,8-TCDD in drinking water, the upper-limit estimate of extra cancer risk per individual is 4.5 × 10⁻³. For lifetime exposure to 1 pg 2,3,7,8-TCDD/m³ in the ambient air, the upper-limit individual risk is 3.3 × 10⁻⁵.     

Copper complexation by dissolved organic matter and uncertainty assessment of their stability constants

The interaction of Cu with dissolved organic matter (DOM, extracted from an organic forest floor) was investigated and the resulting data was evaluated in terms of their uncertainty. The speciation of Cu over ‘free’ Cu (as analysed by diffusive gradients in thin films (DGT)), dissolved Cu–DOM complexes and precipitated Cu–DOM was determined as a function of pH (3.5, 4.0 and 4.5) and Cu/C ratio. The dissolved organically bound fraction was highest at pH 4.5, but this fraction decreased with increasing Cu/C ratio, which was observed for all pH levels. In the range of Cu/C=7×10⁻⁵–2.3×10⁻² (mol/mol) the precipitated fraction was very small. The speciation of both Al and Fe was not affected by increasing Cu concentrations. From a continuous distribution model using the Scatchard approach, we calculated the optimal fit and corresponding upper and lower 95% uncertainty bounds of the overall stability constants (K_o) with the shuffled complex evolution Metropolis (SCEM) algorithm. Although the optimal equation fitted the data very well, the uncertainty of the, according to literature, most reliable approach to establish stability constants, was still large. Accordingly, the usually reported intrinsic stability constants exhibited large uncertainty ranging from logK_i=6.0–7.1 (optimal 6.7) for pH 3.5, logK_i=6.5–7.1 (optimal 6.8) for pH 4.0, and logK_i=6.4–7.2 (optimal 6.8) for pH 4.5 and showed only little effect of pH.