Co-composting of distillery wastes with animal manures: carbon and nitrogen transformations in the evaluation of compost stability

The aim of this work was to study the viability of recycling the solid wastes generated by the winery and distillery industry by means of co-composting with animal manures, as well as to evaluate the quality of the composts obtained. Two piles, using exhausted grape marc and cattle manure or poultry manure, respectively (at ratios, on a fresh weight basis, of 70:30), were composted by the Rutgers static pile composting system. Throughout the composting process, a number of parameters were monitored, such as pH, electrical conductivity, organic matter, water-soluble carbon, water-soluble polyphenols, different forms of nitrogen (organic nitrogen, ammonium and nitrate) and humification indices (humification ratio, humification index, percentage of humic acid-like C, polymerisation ratio and cation exchange capacity), as well as the germination index. Organic matter losses followed first-order kinetics equation in both piles, the highest organic matter mineralisation rate being observed with exhausted grape marc and cow manure. On the other hand, the mixture with the lowest C/N ratio, using exhausted grape marc and poultry manure, showed the highest initial ammonium contents, probably due to the higher and more labile N content of poultry manure. The increase in the cation exchange capacity revealed the organic matter humification during composting. In contrast, other humification parameters, such as the humification ratio and the humification index, did not show the expected evolution and, thus, could not be used to assess compost maturity. Composting produced a degradation of the phytotoxic compounds, such as polyphenols, to give composts without a phytotoxic character. Therefore, composting can be considered as an efficient treatment to recycle this type of wastes, due to composts presented a stable and humified organic matter and without phytotoxic effects, which makes them suitable for their agronomic use.     

Co-composting of spent coffee ground with olive mill wastewater sludge and poultry manure and effect of Trametes versicolor inoculation on the compost maturity

The co-composting of spent coffee grounds, olive mill wastewater sludge and poultry manure was investigated on a semi-industrial scale. In order to reduce the toxicity of the phenolic fraction and to improve the degree of composting humification, composts were inoculated with the white-rot fungus Trametes versicolor in the early stages of the maturation phase.During composting, a range of physico-chemical parameters (temperature and both organic matter and C/N reduction), total organic carbon, total nitrogen, elemental composition, lignin degradation and spectroscopic characteristics of the humic acids (HAs) were determined; impacts of the composting process on germination index of Hordeum vulgare and Lactuca sativa were assessed. The coffee waste proved to be a highly compostable feedstock, resulting in mature final compost with a germination index of 120% in less than 5 months composting. In addition, inoculation with T. versicolor led to a greater degree of aromatization of HA than in the control pile. Moreover, in the inoculated mixture, lignin degradation was three times greater and HA increased by 30% (P < 0.05), compared to the control pile. In the T. versicolor inoculated mixture, the averages of C and N were significantly enhanced in the HA molecules (P < 0.05), by 26% and 22%, respectively. This improvement in the degree of humification was confirmed by the ratio of optical densities of HA solutions at 465 and 665 nm which was lower for HA from the treated mixture (4.5) than that from the control pile (5.4).     

Dynamics of copper and tetracyclines during composting of water hyacinth biomass amended with peat or pig manure

Composting is one of the post-treatment methods for phytoremediation plants. Due to a high potential of water hyacinth to accumulate pollutants, the physicochemical parameters, microbial activity as well as fates of copper (Cu) and tetracyclines (TCs) were investigated for the different amended water hyacinth biomass harvested from intensive livestock and poultry wastewater, including unamended water hyacinth (W), water hyacinth amended with peat (WP), and water hyacinth amended with pig manure (WPM) during the composting process. Pig manure application accelerated the composting process as evidenced by an increase of temperature, electrical conductivity (EC), NH₄-N, as well as functional diversity of microbial communities compared to W and WP treatments. Composting process was slowed down by high Cu, but not by TCs. The addition of peat significantly increased the residual fraction of Cu, while pig manure addition increased available Cu concentration in the final compost. Cu could be effectively transformed into low available (oxidizable) and residual fractions after fermentation. In contrast, less than 0.5% of initial concentrations of TCs were determined at the end of 60-day composting for all treatments in the final composts. The dissipation of TCs was accelerated by the high Cu concentration during composting. Therefore, composting is an effective method for the post-treatment and resource utilization of phytoremediation plants containing Cu and/or TCs.     

The addition of modified attapulgite reduces the emission of nitrous oxide and ammonia from aerobically composted chicken manure

The acceleration of the composting process and the improvement of compost quality have been explored by evaluating the efficacy of various additives, inoculating with specific microorganisms and the application of various biosurfactants. The magnesium-aluminum silicate attapulgite is a low-cost potential composting additive, but its effects on aerobic composting are unknown. This study investigated the effects of attapulgite application on compost production and quality during the aerobic composting of chicken manure. Addition of attapulgite significantly increased the temperature (p < 0.05) while it reduced compost total organic carbon (TOC) and seed germination indices (GIs) throughout the process. Its addition enhanced nitrate concentrations, promoted organic matter degradation, increased seed germination indices, and accelerated the composting process. Interestingly, attapulgite addition did not increase the population of ammonia-oxidizing bacteria. These results suggest that attapulgite is a good additive for the composting industry.

Implications: We investigated the addition of two forms of attapulgite during aerobic composting of chicken manure to determine their effects under strict composting environmental parameter control. Our results provides primary evidence that attapulgite may have potential for application in the composting industry.

All treatments showed no increase within the first 15 days. However, emissions increased for all treatments within 15–45 days, reaching approximately 6300, 2000, and 4000 mg/m² from the control, artifactitious attapulgite, and raw attapulgite treatments, respectively.     

The use of elemental sulphur as organic alternative to control pH during composting of olive mill wastes

High values of pH may represent a limitation for the agricultural use of the composts, not only when used as soil-less substrate but also as soil amendment in high pH soils. The addition of elemental S during the maturation phase of the composting process was evaluated as suitable method to reduce pH of the composts under the organic agriculture regulations. A compost prepared with two phase olive mill waste (OMW) and sheep litter (SL) was used to study the effect of elemental sulphur addition on the pH of the composting mixture. Initially, different bench scale experiments were designed in order to study the influence of moisture, sulphur concentration, and incubation temperature on the sulphur oxidation rate and thus on the pH of the compost. A concentration of 0.5% in sulphur (dry weight basis) and moisture of 40% were proposed as the optimum conditions to decrease the compost pH by 1.1 units without increasing in EC to levels that may suppose a limitation for its agricultural use. Finally, these optimum experimental conditions found at bench scale were tested at full scale in a commercial composting plant treating the same organic materials by windrowing. The pH values of the composting mixture were reduced by one unit after 2 weeks following the addition of elemental S causing no negative effects on the final compost quality.     

Effect of Inoculating Flower Stalks and Vegetable Waste with Ligno-cellulolytic Microorganisms on the Composting Process

Abstract

A lab-scale composting experiment was carried out using vegetable and flower stalks waste to study the effectiveness of ligno-cellulolytic microorganisms (LCMs) obtained from the previous isolation on composting process, especially on enhancement of biodegradation rate of these organic materials. The addition of LCMs to compost showed promised to be a valuable asset by rendering timely benefits in efficiency, maturity, and quality of the composting. This was evidenced by a significant increase of temperature, O₂ consumption and CO₂ emission, and population density of LCMs in compost mass compared with that of biotic (addition of culture of horse feces) and abiotic (1% molasses amendment) treatments, as well as control trial. The phytotoxicity assay showed that the substrate became mature after 60 days’ composting. The LCMs inoculation enhanced the biodegradation of the composting materials as evidenced by an increasing screening ratio (1.2 cm sieve pore) of 34.5% in the treated trail, compared with that of control, which elucidated that big advantage of adding selected inoculants over other treatment, and screening ratio is a reasonable index to compare the quality of different compost. However, the inoculation seemed to have no significant effect on the moisture content, pH, and the final organic carbon of the composting materials.     

ESTROM—a Romanian–Swiss research programme

Background, aim, and scope  Composting is an effective treatment process to realize sludge land application. However, nitrogen loss could result in the reduction of nutrient value of the compost products and the stabilization effect of composting on heavy metal concentration and mobility in sludge has been shown to be very limited. Materials and methods  Laboratory-scale experiments were carried out to investigate the effects of bamboo charcoal (BC) on nitrogen conservation and mobility of Cu and Zn during sludge composting. Results  The result indicated that the incorporation of BC into the sludge composting material could significantly reduce nitrogen loss. With 9% BC amendment, total nitrogen loss at the end of composting decreased 64.1% compared with no BC amendment (control treatment). Mobility of Cu and Zn in the sludge may also have been lessened, based on the decline in diethylenetriaminepentaacetic acid-extractable Cu and Zn contents of composted sludge by 44.4% and 19.3%, respectively, compared to metal extractability in the original material. Discussion  Ammonia adsorption capability of BC might be the main reason for the retention of nitrogen in sludge composting materials. Decrease of extractable Cu²⁺ and Zn²⁺ in the composting material mainly resulted from the adsorption of both metals by BC. Conclusions  Incorporation of BC into composting material could significantly lessen the total nitrogen loss during sludge composting. Mobility of heavy metals in the sludge composting material could also be reduced by the addition of BC. Recommendations and perspectives  Bamboo charcoal could be an effective amendment for nitrogen conservation and heavy metal stabilization in sludge composts. Further research into the effect of BC-amended sludge compost material on soil properties, bioavailability of heavy metals, and nutrient turnover in soil needs to be carried out prior to the application of BC-sludge compost in agriculture.     

Insight into the dynamic microbial community and core bacteria in composting from different sources by advanced bioinformatics methods

Microbial communities are important for high composting efficiency and good quality composts. This study was conducted to compare the changes of physicochemical and bacterial characteristics in composting from different raw materials, including chicken manure (CM), duck manure (DM), sheep manure (SM), food waste (FW), and vegetable waste (VW). The role and interactions of core bacteria and their contribution to maturity in diverse composts were analyzed by advanced bioinformatics methods combined sequencing with co-occurrence network and structural equation modeling (SEM). Results indicated that there were obviously different bacterial composition and diversity in composting from diverse sources. FW had a low pH and different physiochemical characteristics compared to other composts but they all achieved similar maturity products. Redundancy analysis suggested total organic carbon, phosphorus, and temperature governed the composition of microbial species but key factors were different in diverse composts. Network analysis showed completely different interactions of core bacterial community from diverse composts but Thermobifida was the ubiquitous core bacteria in composting bacterial network. Sphaerobacter and Lactobacillus as core genus were presented in the starting mesophilic and thermophilic phases of composting from manure (CM, DM, SM) and municipal solid waste (FW, VW), respectively. SEM indicated core bacteria had the positive, direct, and the biggest (>?80%) effects on composting maturity. Therefore, this study presents theoretical basis to identify and enhance the core bacteria for improving full-scale composting efficiency facing more and more organic wastes.

     

Influence of aeration rate and reactor shape on the composting of poultry manure and sawdust

To achieve successful composting, all the biological, chemical, and physical characteristics need to be considered. The investigation of our study was based on various physicochemical properties, i.e., temperature, ammonia concentration, carbon dioxide concentration, pH, electrical conductivity (EC), carbon/nitrogen (C/N) ratio, organic matter (OM) content, moisture content, bacterial population, and seed germination index (GI), during the composting of poultry manure and sawdust for different aeration rates and reactor shapes. Three cylindrical-shaped and three rectangular-shaped pilot-scale 60-L composting reactors were used in this study, with aeration rates of 0.3 (low), 0.6 (medium), and 0.9 (high) L min^?1 kg^?1 DM (dry matter). All parameters were monitored over 21 days of composting. Results showed that the low aeration rate (0.3 L min^?1 kg^?1 DM) corresponded to a higher and longer thermophilic phase than did the high aeration rate (0.9 L min^?1 kg^?1 DM). Ammonia and carbon dioxide volatilization were directly related to the temperature profile of the substrate, with significant differences between the low and high aeration rates during weeks 2 and 3 of composting but no significant difference observed during week 1. At the end of our study, the final values of pH, EC, moisture content, C/N ratio, and organic matter in all compost reactors were lower than those at the start. The growth rates of mesophilic and thermophilic bacteria were directly correlated with mesophilic and thermophilic conditions of the compost. The final GI of the cylindrical reactor with an airflow rate of 0.3 L min^?1 kg^?1 DM was 82.3%, whereas the GIs of the other compost reactors were below 80%. In this study, compost of a cylindrical reactor with a low aeration rate (0.3 L min^?1 kg^?1 DM) was more stable and mature than the other reactors.

Implications: The poultry industry is growing in South Korea, but there are problems associated with the management of poultry manure, and composting is one solution that could be valuable for crops and forage if managed properly. For high-quality composting, the aeration rate in different reactor shapes must be considered. The objective of this study was to investigate various physicochemical properties with different aeration rates and rector shapes. Results showed that aeration rate of 0.3 L min^?1 kg^?1 DM in a cylindrical reactor provides better condition for maturation of compost.     

Evaluating Environmental Parameters for Minimum Ammonium Losses during Composting of Trimming Residues

Abstract

A neural fuzzy system was used to investigate the influence of environmental variables (time, aeration, moisture, and particle size) on composting parameters (pH, organic matter [OM], nitrogen [N], ammonium nitrogen [NH₄ ⁺-N] and nitrate nitrogen [NO₃ ^--N]). This was to determine the best composting conditions to ensure the maximum quality on the composts obtained with the minimum ammonium losses. A central composite experimental design was used to obtain the neural fuzzy model for each dependent variable. These models, consisting of the four independent process variables, were found to accurately describe the composting process (the differences between the experimental values and those estimated by using the equations never exceeded 5–10% of the former). Results of the modeling showed that creating a product with acceptable chemical properties (pH, NH₄ ⁺-N and NO₃ ^--N) entails operating at medium moisture content (55%) and medium to high particle size (3–5 cm). Moderate to low aeration (0.2 L air/min · kg) would be the best compromise to compost this residue because of the scant statistical influence of this independent variable.     

Concentrations and microbial mineralization of four to six ring polycyclic aromatic hydrocarbons in composted municipal waste

Contents of four to six ring polycyclic aromatic hydrocarbons (PAHs) were estimated in twelve composted municipal wastes of different origin and age. By means of clean-up procedures and subsequent gaschromatography nine different PAHs or isomeric mixtures of PAHs could be separated in extracts. Concentrations of PAHs ranged from 0.17 μg perylene to 56.75 μg benz(a)anthracene/chrysene g^?1 compost (dwt). In each compost the same distinct relation between the amounts of individual PAHs was found. In spite of total weight reduction during compost processing (40–60% loss) no accumulation of PAH concentrations in ripe composts was detected. This points to a decay of PAHs by microbial activities during composting. Degradation studies carried out with four ¹⁴C-labelled PAHs indicated that in fresh composts only minor amounts of PAHs can be degraded. However, microbial populations of ripe composts possess considerable capabilities to mineralize these recalcitrant molecules.     

Advantages and risks of using steel slag in preparing composts from raw organic waste

It had been reported that iron and manganese oxides in steel slag enhanced the production of humic acid (HA) from low-molecular-weight compounds, such as phenolic acids, amino acids, and saccharides. In the present study, this function of steel slag was applied to the composting of raw organic wastes (ROWs). The degree of humification of HAs is an important factor in evaluating compost quality. Thus, HAs were extracted from the prepared composts and the humification parameters were determined, in terms of elemental compositions, acidic functional group contents, molecular weights, spectroscopic parameters from UV–vis absorption and ¹³C NMR spectra. The timing for adding steel slag affected the degree of humification of HAs in the composts. The weight average molecular weight of a HA when slag was added initially (29 kDa) was significantly higher than when slag was added after elevating the temperature of the compost pile (17–18 kDa). These results show that ROWs are decomposed to low-molecular-weight compounds after the pile temperature is elevated and the presence of slag enhances the polycondensation of these compounds to produce HAs with a higher degree of humification. Because the slag used in the present study contained several-tens ng g^?1 to several μg g^?1 of toxic elements (B, Cu, Cr, and Zn), leaching tests for these elements from the prepared composts were carried out. Levels for leaching boron from composts prepared by adding slag (0.2–0.4 mg L^?1) were obviously higher than the corresponding levels without slag (0.05 mg L^?1).     

A comparison of antibiotics,antibiotic resistance genes,and bacterial community in broiler and layer manure following composting

Animal manure is an important source of antibiotics and antibiotic resistance genes (ARGs) in the environment. However, the difference of antibiotic residues and ARG profiles in layer and broiler manure as well as their compost remains unexplored. In this study, we investigated the profiles of twelve antibiotics, seventeen ARGs, and class 1 integrase gene (intI1) in layer and broiler manure, and the corresponding compost at large-scale. Compared with layer manure, broiler manure exhibited approximately six times more residual tetracyclines, especially chlortetracycline. The relative abundances of qnrS and ermA genes in broiler manure were significantly higher than those in layer manure. The concentration of tetracyclines not only had a significantly positive correlation with tetracycline resistance genes (tetA and tetC) but was also positively correlated with quinolone resistance (qepA, qnrB, and qnrS) and macrolide resistance (ermA and ermT). Most ARGs in manure were reduced after composting. However, the relative abundance of sulfonamide resistance gene sul1 increased up to 2.41% after composting, which was significantly higher than that of broiler (0.41%) and layer (0.62%) manure. The associated bacterial community was characterized by high-throughput 16S rRNA gene sequencing. The relative abundances of thermophilic bacteria had significant positive correlations with the abundance of sul1 in compost. The composting has a significant impact on the ARG-associated gut microbes in poultry manure. Variation partitioning analysis indicated that the change of bacterial community compositions and antibiotics contributed partially to the shift in ARG profiles. The results indicate that at industry-scale production broiler manure had more antibiotics and ARGs than layer manure did, and composting decreased most ARG abundances in poultry manure except for sulfonamide resistance genes.

     

不同生物炭对猪粪堆肥过程中抗生素及抗生素抗性基因的削减规律研究

为探讨不同类型生物炭对猪粪堆肥过程中抗生素和抗生素抗性基因(ARGs)的削减规律,分别将玉米秸秆生物炭、竹炭和猪粪生物炭添加到猪粪中进行好氧堆肥,解析不同类型生物炭添加对猪粪堆肥过程中抗生素浓度和ARGs丰度的影响.研究发现,添加竹炭堆肥对抗生素的平均去除率最高(97％),其中对四环素类抗生素的去除率高达98％;添加玉...     

Effects of lime amendment on availability of heavy metals and maturation in sewage sludge composting

A batch composting study was performed to evaluate the feasibility of co-composting sewage sludge with lime, aiming at reducing the availability of heavy metals in the sludge compost. Sewage sludge with sawdust as bulking agent was amended with lime at 0, 0.63, 1.0, and 1.63% w/w, and composted for 100 days in laboratory batch reactors. The changes in temperature, pH, electrical conductivity (EC), and extractable heavy metal contents were measured while compost maturity was determined by C/N(organic) and cress seed germination during the composting period. Liming raised pH of compost effectively at the initial stage of composting and caused a decrease in EC through precipitation of soluble ions. Lime amendment also significantly reduced water-soluble and Diethylene triamine pentracetic acid (DTPA)-extractable metal contents. The maximum reductions were 60 and 40% for Cu, 80 and 40% for Mn, 55 and 10% for Zn, and 20 and 25% for Ni at the end of the composting period for the lime-amended sludge as compared to the control. In spite of the inhibitory effect of lime amendment on the decomposition activity of sewage sludge, all treatments reached maturation after 63 days of composting as indicated by the results of C/N(organic) ratio and cress seed germination test results. A lime amendment of < or =1.0% is recommended to co-compost with sewage sludge.     

Effects of different ratios of pig manure to fungus residue on physicochemical parameters during composting

This study examined physicochemical parameters to assess their effectiveness as stability and maturity indicators during the process of composting pig manure and fungus residue at different ratios. The results showed that composting mixtures with all ratios of pig manure to fungus residue maintained a temperature exceeding 50 °C for more than 10 days during composting and met the requirement for pathogen destruction. The treatment containing mainly pig manure showed higher nitrogen loss and a shorter thermophilic phase and maturity time than the treatment containing mainly fungus residue. The germination index (GI) values indicated that compost maturity was achieved in the final compost with initial ratios of pig manure to fungus residue of 9:1–7:3 (GIs of 101.4%, 91.2%, and 81.3%); the ratio of 6:4 did not reach compost maturity (GI of 63.8%) and had an inhibitory effect on seed germination. The results of this study suggest that a ratio of pig manure to fungus residue of approximately 8:2 can be considered suitable for the efficient and quality composting of pig manure and fungus residue.

Implications: Co-composting of pig manure and edible fungi residue with appropriate proportion can effectively reduce the risk of environmental pollution caused by agricultural wastes, as well as achieve a safer and high-quality organic fertilizer, which can be used to improve physical and chemical properties of the soil, increase crop yields, and promote agricultural sustainable development. Therefore, technique of co-composting of pig manure and edible fungi residue has a wide prospect of application in practical production all over the world.     

Role of biochar on composting of organic wastes and remediation of contaminated soils—a review

Biochar is produced by pyrolysis of biomass residues under limited oxygen conditions. In recent years, biochar as an amendment has received increasing attention on composting and soil remediation, due to its unique properties such as chemical recalcitrance, high porosity and sorption capacity, and large surface area. This paper provides an overview on the impact of biochar on the chemical characteristics (greenhouse gas emissions, nitrogen loss, decomposition and humification of organic matter) and microbial community structure during composting of organic wastes. This review also discusses the use of biochar for remediation of soils contaminated with organic pollutants and heavy metals as well as related mechanisms. Besides its aging, the effects of biochar on the environment fate and efficacy of pesticides deserve special attention. Moreover, the combined application of biochar and compost affects synergistically on soil remediation and plant growth. Future research needs are identified to ensure a wide application of biochar in composting and soil remediation.

Open image in new window

Graphical abstract ?

     

Effect of turning frequency on co-composting pig manure and fungus residue

Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but also can recycle agricultural wastes and transform them into highly valuable products, such as fertilizers or soil conditioners, for agricultural applications. However, the composting process and final product are easily affected by the limited oxygen supply that results from insufficient aeration, especially in the center of a large-scale windrow. Hence, a pilot-scale experiment was conducted to investigate the effects of the turning frequency on the composting efficiency and compost quality of used pig manure and fungus residue. Physical and chemical characteristics were measured over the course of 63 days of composting. The data indicate that higher temperatures and more rapid moisture removal generally result from a turning treatment of once every 2–4 days than in fewer, or no, turning treatments. The total nitrogen, total phosphorus, and total potassium contents increased in all windrows as the organic matter content decreased, but both the increases and decrease were greater in windrows that were turned more frequently. The reduction of the organic matter mass by 53.7–66.0% for a turning of once every 2–8 days is significantly higher than that for the static windrow (39.1%). Although there is an increase in nitrogen mass loss with an increased turning frequency, lower nitrogen mass losses (12.7–25.7%) in all treatments were noted compared with previous studies. A final compost product with less moisture, less weight, higher nutrient content (N, P, and K), and greater stability was obtained in windrows with turning frequencies of once every 2–4 days, which is recommended when composting pig manure and fungus residue.

Implications: Composting of agricultural wastes not only can reduce environmental pollution caused by improper disposal, but recycling of agricultural wastes transforms them into highly valuable products, such as fertilizers or soil conditioners, for agricultural applications. However, the composting process and final product are easily affected by the limited oxygen supply that results from insufficient aeration, especially in the center of a large-scale windrow. Hence, a pilot-scale experiment was conducted to investigate the effects of the turning frequency on the composting efficiency and compost quality of used pig manure and fungus residue, so as to capture an operational technique suitable for the effective co-composting pig manure and edible fungi residue for a large-scale composting plant.     

Effect of inoculating flower stalks and vegetable waste with ligno-cellulolytic microorganisms on the composting process

A lab-scale composting experiment was carried out using vegetable and flower stalks waste to study the effectiveness of ligno-cellulolytic microorganisms (LCMs) obtained from the previous isolation on composting process, especially on enhancement of biodegradation rate of these organic materials. The addition of LCMs to compost showed promised to be a valuable asset by rendering timely benefits in efficiency, maturity, and quality of the composting. This was evidenced by a significant increase of temperature, O2 consumption and CO2 emission, and population density of LCMs in compost mass compared with that of biotic (addition of culture of horse feces) and abiotic (1% molasses amendment) treatments, as well as control trial. The phytotoxicity assay showed that the substrate became mature after 60 days' composting. The LCMs inoculation enhanced the biodegradation of the composting materials as evidenced by an increasing screening ratio (1.2 cm sieve pore) of 34.5% in the treated trail, compared with that of control, which elucidated that big advantage of adding selected inoculants over other treatment, and screening ratio is a reasonable index to compare the quality of different compost. However, the inoculation seemed to have no significant effect on the moisture content, pH, and the final organic carbon of the composting materials.     

The effects of high metal concentrations in soil-compost mixtures on soil enzymes

The study was undertaken to determine the impact of high-metal composts on the activities of four soil enzymes. High concentrations of metal salts (Cr, Cu, Ni or a Co-Mo-Pb combination) were added to feedstocks during the thermophilic stage of composting. These four metal-enriched composts and an unamended control compost were then mixed with soil collected from long-term agriculture plots under organic management or conventional management. The compost-soil mixtures were prepared at two rates (1:1 or 1:3 compost:soil, v/v) and incubated at 20°C for three weeks. These 20 combinations plus the five composts and the two soils were added to pots and incubated for three weeks. Following incubation, soil enzyme activities (acid phosphatase, arysulfatase, dehydrogenase, phosphodiesterase) were measured using traditional assay procedures. Compared to the control, none of the high-metal composts inhibited soil enzyme activity. Notably, the Cu compost treatment produced significantly higher activity of all four enzymes in the soil compared to the control. Previous soil management influenced the activity of three enzymes, arysulfatase and dehydrogenase had greater activity in the organic soil while phosphatase activity was greater in the conventional soil. Increasing the proportion of compost in the pot had a positive effect on phosphodiesterase activity only. In conclusion, the high-metal compost treatments either enhanced or caused no adverse effects on soil enzyme activity.