Performance evaluation of a continuous flow photocatalytic reactor for wastewater treatment

A novel photocatalytic reactor for wastewater treatment was designed and constructed. The main part of the reactor was an aluminum tube in which 12 stainless steel circular baffles and four quartz tube were placed inside of the reactor like shell and tube heat exchangers. Four UV–C lamps were housed within the space of the quartz tubes. Surface of the baffles was coated with TiO₂. A simple method was employed for TiO₂ immobilization, while the characterization of the supported photocatalyst was based on the results obtained through performing some common analytical methods such as X-ray diffraction (XRD), scanning electron microscope (SEM), and BET. Phenol was selected as a model pollutant. A solution of a known initial concentration (20, 60, and 100 ppmv) was introduced to the reactor. The reactor also has a recycle flow to make turbulent flow inside of the reactor. The selected recycle flow rate was 7?×?10^?5 m³.s^?1, while the flow rate of feed was 2.53?×?10^?7, 7.56?×?10^?7, and 1.26?×?10^?6 m³.s^?1, respectively. To evaluate performance of the reactor, response surface methodology was employed. A four-factor three-level Box–Behnken design was developed to evaluate the reactor performance for degradation of phenol. Effects of phenol inlet concentration (20–100 ppmv), pH (3–9), liquid flow rate (2.53?×?10^?7?1.26?×?10^?6 m³.s^?1), and TiO₂ loading (8.8–17.6 g.m^?2) were analyzed with this method. The adjusted R ² value (0.9936) was in close agreement with that of corresponding R ² value (0.9961). The maximum predicted degradation of phenol was 75.50 % at the optimum processing conditions (initial phenol concentration of 20 ppmv, pH?～?6.41, and flow rate of 2.53?×?10^?7 m³.s^?1 and catalyst loading of 17.6 g.m^?2). Experimental degradation of phenol determined at the optimum conditions was 73.7 %. XRD patterns and SEM images at the optimum conditions revealed that crystal size is approximately 25 nm and TiO₂ nanoparticles with visible agglomerates distribute densely and uniformly over the surface of stainless steel substrate. BET specific surface area of immobilized TiO₂ was 47.2 and 45.8 m² g^?1 before and after the experiments, respectively. Reduction in TOC content, after steady state condition, showed that maximum phenol decomposition occurred at neutral condition (pH?～?6). Figure

The schematic view of the experimental set-up     

Photocatalytic mineralization of glyphosate in a small-scale plug flow simulation reactor by UV/TiO2

The present work involves the photocatalytic mineralization of glyphosate on a plug flow reactor by UV/TiO₂. The effect of catalyst loading shows an optimal value (0.4 g L^?1) which is necessary to mineralize glyphosate. The kinetic rate of glyphosate mineralization decreases with the increasing initial concentration of glyphosate, and the data can be described using the first-order model. An alkaline environment is conducive to glyphosate mineralization. The mineralization efficiency increases with elevated flow rate to 114 mL min^?1, which is followed by a decrease with a further increase in flow rate due to the reduction of the residence time. The presence of external oxidants (K₂S₂O₈, H₂O₂ and KBrO₃) and photosencitizer (humic acid) can significantly enhance glyphosate mineralization. Photocatalysis oxidation ability of the three studied oxidants decrease in the order of: S₂O₈ ^2? > BrO₃ ^? > H₂O₂. Finally, the Langmuir–Hinshelwood (L-H) model was used to rationalize the mechanisms of reactions occurring on TiO₂ surfaces and L-H model constants were also determined.     

Photocatalytic degradation of contaminants of concern with composite NF-TiO2 films under visible and solar light

This study reports the synthesis and characterization of composite nitrogen and fluorine co-doped titanium dioxide (NF-TiO₂) for the removal of contaminants of concern in wastewater under visible and solar light. Monodisperse anatase TiO₂ nanoparticles of different sizes and Evonik P25 were assembled to immobilized NF-TiO₂ by direct incorporation into the sol–gel or by the layer-by-layer technique. The composite films were characterized with X-ray diffraction, high-resolution transmission electron microscopy, environmental scanning electron microscopy, and porosimetry analysis. The photocatalytic degradation of atrazine, carbamazepine, and caffeine was evaluated in a synthetic water solution and in an effluent from a hybrid biological concentrator reactor (BCR). Minor aggregation and improved distribution of monodisperse titania particles was obtained with NF-TiO₂-monodisperse (10 and 50 nm) from the layer-by-layer technique than with NF-TiO₂?+?monodisperse TiO₂ (300 nm) directly incorporated into the sol. The photocatalysts synthesized with the layer-by-layer method achieved significantly higher degradation rates in contrast with NF-TiO₂-monodisperse titania (300 nm) and slightly faster values when compared with NF-TiO₂-P25. Using NF-TiO₂ layer-by-layer with monodisperse TiO₂ (50 nm) under solar light irradiation, the respective degradation rates in synthetic water and BCR effluent were 14.6 and 9.5?×?10^?3?min^?1 for caffeine, 12.5 and 9.0?×?10^?3?min^?1 for carbamazepine, and 10.9 and 5.8?×?10^?3?min^?1 for atrazine. These results suggest that the layer-by-layer technique is a promising method for the synthesis of composite TiO₂-based films compared to the direct addition of nanoparticles into the sol.     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Solar CPC pilot plant photocatalytic degradation of bisphenol A in waters and wastewaters using suspended and supported-TiO2. Influence of photogenerated species

Photocatalytic degradation of bisphenol A (BPA) in waters and wastewaters in the presence of titanium dioxide (TiO₂) was performed under different conditions. Suspensions of the TiO₂ were used to compare the degradation efficiency of BPA (20 mg L^?1) in batch and compound parabolic collector (CPC) reactors. A TiO₂ catalyst supported on glass spheres was prepared (sol–gel method) and used in a CPC solar pilot plant for the photodegradation of BPA (100 μg L^?1). The influence of OH·, O₂ ^·?, and h ⁺ on the BPA degradation were evaluated. The radicals OH· and O₂ ^·? were proved to be the main species involved on BPA photodegradation. Total organic carbon (TOC) and carboxylic acids were determined to evaluate the BPA mineralization during the photodegradation process. Some toxicological effects of BPA and its photoproducts on Eisenia andrei earthworms were evaluated. The results show that the optimal concentration of suspended TiO₂ to degrade BPA in batch or CPC reactors was 0.1 g L^?1. According to biological tests, the BPA LC₅₀ in 24 h for E. andrei was of 1.7?×?10^?2 mg cm^?2. The photocatalytic degradation of BPA mediated by TiO₂ supported on glass spheres suffered strong influence of the water matrix. On real municipal wastewater treatment plant (MWWTP) secondary effluent, 30 % of BPA remains in solution; nevertheless, the method has the enormous advantage since it eliminates the need of catalyst removal step, reducing the cost of treatment.     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Electrosorption and photocatalytic one-stage combined process using a new type of nanosized TiO2/activated charcoal plate electrode

In the present study, an activated charcoal (AC) plate was prepared by physical activation method. Its surface was coated with TiO₂ nanoparticles by electrophoretic deposition (EPD) method. The average crystallite size of TiO₂ nanoparticles was determined approximately 28 nm. The nature of prepared electrode was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller (BET) surface area measurement before and after immobilization. The electrosorption and photocatalytic one-stage combined process was investigated in degradation of Lanasol Red 5B (LR5B), and the effect of dye concentration, electrolyte concentration, pH, voltage, and contact time was optimized and modeled using response surface methodology (RSM) approach. The dye concentration of 30 mg L^?1, Na₂SO₄ concentration of 4.38 g L^?1, pH of 4, voltage of 250 mV, and contact time of 120 min were determined as optimum conditions. Decolorization efficiency increased in combined process to 85.65 % at optimum conditions compared to 66.03 % in TiO₂/AC photocatalytic, 20.09 % in TiO₂/AC electrosorption, and 1.91 % in AC photocatalytic processes.     

The use of nanovermiculite catalyst in the study of removal of the organic load and degradation of atrazine via ozone process in RPB reactor

Abstract

The main objective of this study is the degradation of a synthetic solution of atrazine by a modified vermiculite catalyzed ozonation, in a rotating packed bed (RPB) reactor. A 0.5?L RPB reactor was used to perform the experiments, using a Central Composite Design (CCD) response surface to construct the quadratic model based on the factors: pH, catalyst concentration and reactor rotation frequency. The response variable was the removal of the organic load measured in terms of Chemical Oxygen Demand (COD). After the complete quadratic model was constructed through the response surface, the COD degradation process had an optimal removal of 41% under the following conditions: pH 8.0, rotation of 1150?rpm and catalyst concentration 0.66?g L^?1.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Phosphorus removal in a sulfur–limestone autotrophic denitrification (SLAD) biofilter

The sulfur–limestone autotrophic denitrification (SLAD) biofilter was able to remove phosphorous from wastewater during autotrophic denitrification. Parameters influencing autotrophic denitrification in the SLAD biofilter, such as hydraulic retention time (HRT), influent nitrate (NO₃ ^?), and influent PO₄ ^3? concentrations, had significant effects on P removal. P removal was well correlated with total oxidized nitrogen (TON) removed in the SLAD biofilter; the more TON removed, the more efficient P removal was achieved. When treating the synthetic wastewater containing NO₃ ^?-N of 30 mg L^?1 and PO₄ ^3?-P of 15 mg L^?1, the SLAD biofilter removed phosphorus of 45 % when the HRT was 6 h, in addition with TN removal of nearly 100 %. The optimal phosphorus removal in the SLAD biofilter was around 60 %. For the synthetic wastewater containing a PO₄ ^3?-P concentration of 15 mg L^?1, the main mechanism of phosphorus removal was the formation of calcium phosphate precipitates.     

Disinfection performance of chlorine dioxide gas at ultra-low concentrations and the decay rules under different environmental factors

ABSTRACT

Gaseous chlorine dioxide (ClO₂) is one of the most promising air disinfectants. In this study, an ultra-low concentration of ClO₂ gas (< 1.2 mg/m³) was generated in an office at various levels of humidity and illuminance to investigate the decay law. The disinfection efficiency and metal corrosiveness of ultra-low concentrations of ClO₂ gas were also studied using an experimental chamber. At 48% and 75% humidity, the decay rate constants of ClO₂ gas were 0.0034 min^?1 and 0.0036 min^?1, respectively. The rate of decline of the ClO₂ concentration increased as the humidity of the environment increased. The decay rate constant of ClO₂ gas at an illuminance of 76 lux and 3429 lux was 0.0034 min^?1 and 0.00427 min^?1, respectively; hence, the decay rate increased with increased illumination. At a humidity of 72% and illuminance of 2112 lux, the decay rate constant reached 0.00880 min^?1. The effects of humidity and illuminance on the attenuation of the ClO₂ concentration were strongly synergistic. When the gas concentration was maintained below 0.9 mg/m³, the disinfection rate of ClO₂ on bacteria (P. aeruginosa, V. mimicus and S. aureus) exceeded 99.9%; thus, ClO₂ gas exhibited a high disinfection efficiency. In addition, there was no corrosion to various metals by ClO₂ under the same conditions. Consequently, gaseous ClO₂ at ultra-low concentrations has a high sterilization efficiency and is non-corrosive to metals.     

Kinetics of imidazolium-based ionic liquids degradation in aqueous solution by Fenton oxidation

In the last few years, several works dealing with Fenton oxidation of ionic liquids (ILs) have proved the capability of this technology for their degradation, achieving complete ILs removal and non-toxic effluents. Nevertheless, very little is known about the kinetics of this process, crucial for its potential application. In this work, the effect of several operating conditions, including reaction temperature (50–90 °C), catalyst load (10–50 mg L^?1 Fe³⁺), initial IL concentration (100–2000 mg L^?1), and hydrogen peroxide dose (10–200% of the stoichiometric amount for the complete IL mineralization) on 1-butyl-3-methylimidazolium chloride ([C₄mim]Cl) oxidation has been investigated. Under the optimum operating conditions (T = 90 °C; [Fe³⁺]₀ = 50 mg L^?1; [H₂O₂]₀ = 100% of the stoichiometric amount), the complete removal of [C₄mim]Cl (1000 mg L^?1) was achieved at 1.5-min reaction time. From the experimental results, a potential kinetic model capable to describe the removal of imidazolium-based ILs by Fenton oxidation has been developed. By fitting the proposed model to the experimental data, the orders of the reaction with respect to IL initial concentration, Fe³⁺ amount and H₂O₂ dose were found to be close to 1, with an apparent activation energy of 43.3 kJ mol^?1. The model resulted in a reasonable fit within the wide range of operating conditions tested in this work.     

Response surface optimization of a dynamic dye adsorption process: a case study of crystal violet adsorption onto NaOH-modified rice husk

The adsorption of crystal violet from aqueous solution by NaOH-modified rice husk was investigated in a laboratory-scale fixed-bed column. A two-level three factor (2³) full factorial central composite design with the help of Design Expert Version 7.1.6 (Stat Ease, USA) was used for optimisation of the dynamic dye adsorption process and evaluation of interaction effects of different operating parameters: initial dye concentration (100–200 mg L^?1), flow rate (10–30 mL min^?1) and bed height (5–25 cm). A correlation coefficient (R ²) value of 0.999, model F value of 1,936.59 and its low p value (<0.0001) along with lower value of coefficient of variation (1.38 %) indicated the fitness of the response surface quadratic model developed during the present study. Numerical optimisation applying desirability function was used to identify the optimum conditions for a targeted breakthrough time of 12 h. The optimum conditions were found to be initial solution pH?=?8.00, initial dye concentration?=?100 mg L^?1, flow rate?=?22.88 mL min^?1 and bed height?=?18.75 cm. A confirmatory experiment was performed to evaluate the accuracy of the optimised procedure. Under the optimised conditions, breakthrough appeared after 12.2 h and the column efficiency was determined as 99 %. The Thomas model showed excellent fit to the dynamic dye adsorption data obtained from the confirmatory experiment. Thereby, it was concluded that the current investigation gives valuable insights for designing and establishing a continuous wastewater treatment plant.     

Influence of aeration rate and reactor shape on the composting of poultry manure and sawdust

To achieve successful composting, all the biological, chemical, and physical characteristics need to be considered. The investigation of our study was based on various physicochemical properties, i.e., temperature, ammonia concentration, carbon dioxide concentration, pH, electrical conductivity (EC), carbon/nitrogen (C/N) ratio, organic matter (OM) content, moisture content, bacterial population, and seed germination index (GI), during the composting of poultry manure and sawdust for different aeration rates and reactor shapes. Three cylindrical-shaped and three rectangular-shaped pilot-scale 60-L composting reactors were used in this study, with aeration rates of 0.3 (low), 0.6 (medium), and 0.9 (high) L min^?1 kg^?1 DM (dry matter). All parameters were monitored over 21 days of composting. Results showed that the low aeration rate (0.3 L min^?1 kg^?1 DM) corresponded to a higher and longer thermophilic phase than did the high aeration rate (0.9 L min^?1 kg^?1 DM). Ammonia and carbon dioxide volatilization were directly related to the temperature profile of the substrate, with significant differences between the low and high aeration rates during weeks 2 and 3 of composting but no significant difference observed during week 1. At the end of our study, the final values of pH, EC, moisture content, C/N ratio, and organic matter in all compost reactors were lower than those at the start. The growth rates of mesophilic and thermophilic bacteria were directly correlated with mesophilic and thermophilic conditions of the compost. The final GI of the cylindrical reactor with an airflow rate of 0.3 L min^?1 kg^?1 DM was 82.3%, whereas the GIs of the other compost reactors were below 80%. In this study, compost of a cylindrical reactor with a low aeration rate (0.3 L min^?1 kg^?1 DM) was more stable and mature than the other reactors.

Implications: The poultry industry is growing in South Korea, but there are problems associated with the management of poultry manure, and composting is one solution that could be valuable for crops and forage if managed properly. For high-quality composting, the aeration rate in different reactor shapes must be considered. The objective of this study was to investigate various physicochemical properties with different aeration rates and rector shapes. Results showed that aeration rate of 0.3 L min^?1 kg^?1 DM in a cylindrical reactor provides better condition for maturation of compost.     

Coupling of titania with multiwall carbon nanotubes for decomposition of gas-phase pollutants under simulated indoor conditions

This study synthesized multiwall carbon nanotube (MWNT)–titania (TiO₂) composites and examined their characteristics and photocatalytic performance for the cleaning of gas-phase benzene, toluene, ethyl benzene, and o-xylene (BTEX) under simulated indoor conditions. Optical and spectral surveys of the as-synthesized composite confirmed that the TiO₂ nanoparticles were bound intimately to the MWNT networks. The photocatalytic performance was evaluated using an annular-type reactor inner-coated with MWNT–TiO₂ or Degussa P25 TiO₂. The composite revealed gas removal ability superior to that of stand-alone TiO₂. This composite was also less affected by humidity during toluene decomposition compared to the previous result obtained from a stand-alone TiO₂. Unlike another previous result obtained from the TiO₂, the performance of the composite was not affected by changes in input concentration (IC) within a simulated indoor air quality range (0.1–1.0 ppm) but it decreased significantly when the IC was increased to 5 and 10 ppm. As the flow rate was decreased from 4.0 to 1.0 L min^?1, the average efficiency for the target compounds increased to 95% or ～100%. The MWNT–TiO₂ composite could be applied effectively to the decomposition for BTEX under certain simulated indoor conditions.

Implications: Unlike water applications, there are few reports of gas-phase applications of multiwall carbon nanotubes (MWCNT)–TiO₂ composites. This study found that MWCNT–TiO₂ composites showed performance in the removal of toxic gaseous aromatic superior to that of stand-alone TiO₂. In addition, the pollutant degradation efficiency of the composite was less affected by humidity than for a stand-alone TiO₂ unit within a simulated indoor relative humidity range. Moreover, unlike the TiO₂ unit, the composite's performance was not affected by variations in the input concentrations within the simulated indoor air quality (IAQ) range. In addition, the decomposition efficiencies increased to 100% with decreasing flow rate.     

Assessment of solar driven TiO2-assisted photocatalysis efficiency on amoxicillin degradation

The objective of this work was to evaluate the efficiency of a solar TiO₂-assisted photocatalytic process on amoxicillin (AMX) degradation, an antibiotic widely used in human and veterinary medicine. Firstly, solar photolysis of AMX was compared with solar photocatalysis in a compound parabolic collectors pilot scale photoreactor to assess the amount of accumulated UV energy in the system (Q _UV) necessary to remove 20 mg L^?1 AMX from aqueous solution and mineralize the intermediary by-products. Another experiment was also carried out to accurately follow the antibacterial activity against Escherichia coli DSM 1103 and Staphylococcus aureus DSM 1104 and mineralization of AMX by tracing the contents of dissolved organic carbon (DOC), low molecular weight carboxylate anions, and inorganic anions. Finally, the influence of individual inorganic ions on AMX photocatalytic degradation efficiency and the involvement of some reactive oxygen species were also assessed. Photolysis was shown to be completely ineffective, while only 3.1 kJ_UV?L^?1 was sufficient to fully degrade 20 mg L^?1 AMX and remove 61 % of initial DOC content in the presence of the photocatalyst and sunlight. In the experiment with an initial AMX concentration of 40 mg L^?1, antibacterial activity of the solution was considerably reduced after elimination of AMX to levels below the respective detection limit. After 11.7 kJ_UV?L^?1, DOC decreased by 71 %; 30 % of the AMX nitrogen was converted into ammonium and all sulfur compounds were converted into sulfate. A large percentage of the remaining DOC was in the form of low molecular weight carboxylic acids. Presence of phosphate ions promoted the removal of AMX from solution, while no sizeable effects on the kinetics were found for other inorganic ions. Although the AMX degradation was mainly attributed to hydroxyl radicals, singlet oxygen also plays an important role in AMX self-photosensitization under UV/visible solar light.     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

Removal of organochlorine pesticides from lindane production wastes by electrochemical oxidation

This study is focused on the effective removal of recalcitrant pollutants hexaclorocyclohexanes (HCHs, isomers α, β, γ, and δ) and chlorobenzenes (CBs) present in a real groundwater coming from a landfill of an old lindane factory. Groundwater is characterized by a total organic carbon (TOC) content of 9 mg L^?1, pH₀?=?7, conductivity?=?3.7 mS cm^?1, high salt concentration (SO₄^2?, HCO₃^?, Cl^?), and ferrous iron in solution. The experiments were performed using a BDD anode and a carbon felt (CF) cathode at the natural groundwater pH and without addition of supporting electrolyte. The complete depletion of the four HCH isomers and a mineralization degree of 90% were reached at 4-h electrolysis with a current intensity of 400 mA, the residual TOC (0.8 mg L^?1) corresponding mainly to formic acid. A parallel series reaction pathway was proposed: HCHs and CBs are transformed into chlorinated and hydroxylated intermediates that are rapidly oxidized to non-toxic carboxylic acids and/or mineralized, leading to a rapid decrease in solution pH.     

Isovaleraldehyde elimination by UV/TiO2 photocatalysis: comparative study of the process at different reactors configurations and scales

A proposal for scaling-up the photocatalytic reactors is described and applied to the coated catalytic walls with a thin layer of titanium dioxide under the near ultraviolet (UV) irradiation. In this context, the photocatalytic degradation of isovaleraldehyde in gas phase is studied. In fact, the removal capacity is compared at different continuous reactors: a photocatalytic cylindrical reactor, planar reactor, and pilot unit. Results show that laboratory results can be useful for reactor design and scale-up. The flowrate increases lead to the removal capacity increases also. For example, with pilot unit, when flowrate extends four times, the degradation rate varies from 0.14 to 0.38 g h^?1 m_cat ^?2. The influence of UV intensity is also studied. When this parameter increases, zboth degradation rate and overall mineralization are enhanced. Moreover, the effects of inlet concentration, flowrate, geometries, and size of reactors on the removal capacity are also studied.     

Acute toxicity and ecotoxicological risk assessment of rice pesticides to Lithobates catesbeianus tadpoles

The objective of this study was to determine the acute toxicity of some pesticides used in irrigated rice farming to Lithobates catesbeianus tadpoles. The LC_50-96h for commercial formulations containing bentazon, penoxsulam, vegetable oil, permethrin and carbofuran, separately and their mixtures, were determined at the proportions commonly used in the field. The limits of risk concentrations of these products for the studied species were also established. The LC_50-96h for tadpoles was 4,530 mg L^?1 for bentazon; 7.52 mg L^?1 for penoxsulam + 145.66 mg L^?1 of vegetable oil; 81.57 mg L^?1 for vegetable oil; 0.10 mg L^?1 for permethrin; 29.90 mg L^?1 for carbofuran (active ingredients), and 38.79 times the dose used in the field for the mixture of these products. The environmental risk was determined only for permethrin, and care should be taken when using the vegetable oil.