Thermal,Rheological, Mechanical and Morphological Behavior of High Density Polyethylene and Carboxymethyl Cellulose Blend

In this study water soluble sodium carboxymethyl cellulose (CMC) was blended with high density polyethylene (HDPE) by peroxide-initiated melt compounding technique. The compatibility of the blended polymers were carried out by silane crosslinking agent. A series of blends were prepared by varying the CMC contents up to a maximum of 50 phr. The physical properties of non-crosslinked and crosslinked blends were investigated in detail. FTIR analysis of crosslinked blend confirmed the presence of Si–O–Si and Si–O–C absorption peaks at 1050 and 1159 cm^?1. Thermal stability of crosslinked blends improved as compared to its non-crosslinked congener. Rheological study of crosslinked blends illustrated high complex viscosity and dynamic shear storage modulus. The tensile strength of virgin polyethylene was 8.1 MPa whereas the maximum tensile strength of 19.6 MPa was observed in crosslinked blend. Similarly lower deformation was observed in crosslinked blends under static load. Scanning electron microscopy of crosslinked formulations also showed strong adhesion between the polymers interface. The compatibility of HDPE and CMC is attributed to both free radical and condensation reactions.     

Preparation and Properties of Carboxymethyl Cellulose (CMC)/Sodium alginate (SA) Blends Induced by Gamma Irradiation

Carboxymethyl Cellulose (CMC)/Sodium alginate (SA) blends have been prepared by casting solution method. The effect of different irradiation doses (2.5, 5, 10, 15, and 20 kGy) of gamma rays on the physical properties of the CMC/SA blend containing different ratios of SA (20, 30, and 40 %) such as gel fraction (%) and swelling (%) of CMC/SA blends were investigated. It was found that the gel fraction increases with increasing irradiation dose up to 20 kGy while the swelling of CMC/SA blend films tends to increase with increasing SA content and reduced with increasing irradiation doses. Mechanical and thermal properties of the blend films were improved when CMC content increased and with increasing irradiation dose up to 20 kGy. Morphology of the blend was examined by SEM, which indicates compatibility between CMC and SA. The blend rich in SA content possessed good antimicrobial activity against Gram +ve Bacteria (Bacillus subtilis).     

A Biobased Blend of Cellulose Diacetate with Starch

Two bio-based polymers, cellulose diacetate (CDA) and starch, were used to prepare blends with reasonable properties and low cost. Due to the poor processing properties, starch was modified in the presence of glycerol and epoxidized soybean oil (ESO), and CDA was plasticized by triacetin (TA) and ESO, respectively. The morphologies of the blends with different amounts of modified starch (MST) were studied by scanning electron microscope (SEM), and the physical properties of the blends, including thermal stability, mechanical property, water and moisture resistance, were investigated. The equilibrium moisture absorption rates of the blends containing 30 and 50 wt% MST at 100 % of relative humidity(RH) were 9.4 and 15.0 %, respectively. SEM and DMA results demonstrated that CDA and MST had a certain extent of compatibility. Due to the partial plasticization of starch, the tensile strength of the blends was nearly not affected by the amount of MST. Even if 50 wt% MST was added, the tensile strength of the blend was as high as 24.7 MPa. The obtained blend containing 30 wt% MST can keep good mechanical properties at 50 % RH, and its tensile strength and elongation at break are 30.2 MPa and 3.6 %, respectively. All the results show that the CDA/MST blends have a potential as an environmental friendly material.     

Biodegradable Poly(butylene succinate) and Poly(butylene adipate-co-terephthalate) Blends: Reactive Extrusion and Performance Evaluation

Two biodegradable polyesters, poly(butylene adipate-co-terephthalate) (PBAT) and poly(butylene succinate) (PBS) were melt-compounded in a twin screw extruder to fabricate a novel PBS/PBAT blend. The compatibility of the blend was attributed to the transesterification reaction that was confirmed by Fourier transform infrared spectroscopy. The Gibbs free energy equation was applied to explain the miscibility of the resulting blend. Dynamic mechanical analysis of the blends exhibits an intermediate tanδ peak compared to the individual components which suggests that the blend achieved compatibility. One of the key findings is that the tensile strength of the optimized blend is higher than each of the blended partner. Rheological properties revealed a strong shear-thinning tendency of the blend by the addition of PBAT into PBS. The phase morphology of the blends was observed through scanning electron microscopy, which revealed that phase separation occurred in the blends. The spherulite growth in the blends was highly influenced by the crystallization temperature and composition. In addition, the presence of a dispersed amorphous phase was found to be a hindrance to the spherulite growth, which was confirmed by polarizing optical microscopy. Furthermore, the increased crystallization ability of PBAT in the blend systems gives the blend a balanced thermal resistance property.     

Effect of Poly(dioxolane) as Compatibilizer in Poly(ɛ-caprolactone)/Tapioca Starch Blends

The influence of poly(dioxolane) (PDXL), a poly(ethylene oxide-alt-methylene oxide), as compatibilizer on poly(ɛ-caprolactone) (PCL)/tapioca starch (TS) blends was studied. In order to facilitate blending; PCL, PDXL and TS must be blended together directly; so that PDXL is partially adhered at the TS surface as shown by scanning electron microscopy. The molecular weight effect of PDXL on the PCL/TS blends showed that mechanical properties of PCL/TS/PDXL blends from low molecular weight (M _n=10,000) and high molecular weight (M _n=200,000) PDXL were rather dependent on TS content. The enzymatic degradability of PCL/TS/PDXL blends using α-amylase increased as the TS content increased but was independent on the dispersion of tapioca starch in the PCL matrix.     

Lightweight Concrete Containing an Alkaline Resistant Starch-Based Aquagel

Starch aquagel-based lightweight concrete has properties similar to those of other lightweight concrete products. However, starch aquagels are unstable in the strongly alkaline conditions typical of Portland Cement-based concrete and may interfere with the setting process. The effect of alkali treatments on the physical, mechanical, and functional properties of starch aquagels and aquagels from starch/polymer blends was investigated. Starch was blended at 100–115°C in a twin-screw extruder with five different polymers to determine whether the blends improved alkaline resistance. Polymer blends containing 5%, 15%, and 30% of the polymer hydrated and formed aquagels when equilibrated in water for 24 h. However, equilibrium moisture content was lower for the blends compared to the starch control. Aquagels equilibrated in 0.15 N NaOH swelled, lost compressive strength and had greater than 90% moisture. The blend of starch and 30% PVOH absorbed less moisture and was more resistant to alkaline dissolution in 1 N NaOH than the other blends tested making it a more suitable material for aquagel-based concrete. The moisture content of starch-based aquagels and mixing time were critical factors in determining setting times. The size of aquagel blends had a minor effect on density and compressive strength.     

Water transport in polylactic acid (PLA), PLA/ polycaprolactone copolymers, and PLA/polyethylene glycol blends

Polylactic acid (PLA) is a hydrolytically degradable aliphatic polyester, and water vapor permeability may have a significant influence on the rate of degradation. A method is devised to use bags prepared from PLA films and filled with molecular sieves to determine the water vapor permeability in the polymer, its copolymers with caprolactone, and blends with polyethylene glycol. The “solution-diffusion” model is used to determine the permeability parameters. These include the solubility coefficient,S, a measure of the equilibrium water concentration available for hydrolysis and the diffusion coefficient,D, which characterizes the rate of water vapor diffusion into the film under specific conditions. Values ofS andD at 50‡C and 90% relative humidity ranged from 400 × 10^-6 to 1000 × 10^-6 cm³ (STP)/(cm³ Pa) and 0.20 × 10^-6 to 1.0 × 10^-6 cm²/s, respectively. TheS andD coefficients were also measured at 20 and 40‡C and compared to those of other polymers. The degree of crystallinity was found to have little influence on the measured permeability parameters. The heat of sorption, δH_S, and the activation energy of diffusion, E_D, were used to show that the permeability process is best described by the “water cluster” model for hydrophobic polymers. Finally, the diffusion coefficient is used to compare the rate of water diffusion to the rate of water consumption by ester hydrolysis. Results indicate that hydrolytic degradation of PLA is reaction-controlled.     

Starch, Poly(lactic acid), and Poly(vinyl alcohol) Blends

Research on biodegradable materials has been stimulated due to concern regarding the persistence of plastic wastes. Blending starch with poly(lactic acid) (PLA) is one of the most promising efforts because starch is an abundant and cheap biopolymer and PLA is biodegradable with good mechanical properties. Poly(vinyl alcohol) (PVOH) contains unhydrolytic residual groups of poly(vinyl acetate) and also has good compatibility with starch. It was added to a starch and PLA blend (50:50, w/w) to enhance compatibility and improve mechanical properties. PVOH (M_W 6,000) at 10%, 20%, 30%, 40%, 50% (by weight) based on the total weight of starch and PLA, and 30% PVOH at various molecular weights (M_W 6,000, 25,000, 78,000, and 125,000 dalton) were added to starch/PLA blends. PVOH interacted with starch. At proportions greater than 30%, PVOH form a continuous phase with starch. Tensile strength of the starch/PLA blends increased as PVOH concentration increased up to 40% and decreased as PVOH molecular weight increased. The increasing molecular weight of PVOH slightly affected water absorption, but increasing PVOH concentration to 40% or 50% increased water absorption. Effects of moisture content on the starch/PLA/PVOH blend also were explored. The blend containing gelatinized starch had higher tensile strength. However, gelatinized starch also resulted in increased water absorption.     

Biodegradability of PMMA Blends with Some Cellulose Derivatives

High polymer blends of Polymethyl methacrylate (PMMA) with cellulose acetate (CA) and Cellulose acetate phthalate (CAP) of varying blend compositions have been prepared to study their biodegradation behavior and blend miscibility. Films of PMMA–CA, and PMMA–CAP blends have been prepared by solution casting using Acetone and Dimethyl formamide(DMF) as solvents respectively. Biodegradability of these blends has been studied by four different methods namely, soil burial test, enzymatic degradation, and degradation in phosphate buffer and activated sludge degradation followed by water absorption tests to support the degradation studies. Degradation analysis was done by weight loss method. The results of all the tests showed sufficient biodegradability of these blends. Degradability increased with the increase in CA and CAP content in the blend compositions. The miscibility of PMMA–CA and PMMA–CAP blends have been studied by solution viscometric and ultrasonic methods. The results obtained reveal that PMMA forms miscible blends with either CA or CAP in the entire composition range. Miscibility of the blends may be due to the formation of hydrogen bond between the carbonyl group of PMMA and the free hydroxyl group of CA and CAP.     

Evaluation of the Biodegradability of Polyvinyl Alcohol/Starch Blends: A Methodological Comparison of Environmentally Friendly Materials

Polyvinyl alcohol (PVA) and starch are both biodegradable polymers. These two polymers can be prepared as biodegradable plastics that are emerging as one of the environmental friendly materials available now. In this study, after reacting with sodium trimetaphosphate (STMP), modified corn starch was blended with PVA in different ratios by a barbender. Test samples were prepared for mechanical and thermal properties measurements. The surface roughness and morphology of fractured surface of the samples were observed by an atomic force microscopy (AFM) and scanning electron microscope (SEM) measurements. Aqueous degradation by enzyme, water absorption and biodegradability behavior were evaluated for the degradability. The biodegradability of these materials was followed by bio-reactivity kinetics models. Results showed that the addition of modified starch could enhance its water uptake. With an addition of 20 wt% of modified starch, the blend had a maximum weight loss during enzymatic degradation. It was found that the degradability was enhanced with the addition of the starch. Analyzing the results of the biodegradability based on the kinetic models, the growth rate of the microorganism was found to be increasing with the increase of the content of starch in the PVA/starch blends in the first order reaction fashion. In our biodegradability analysis, i.e., based on the China national standards (CNS) 14432 regulations, we estimated the decomposition behavior based on the mentioned first order reaction. We found that the PVA/starch blends would take 32.47, 16.20 and 12.47 years to degrade by 70% as their starch content 0, 20 and 40 wt%, respectively.     

Effects of Modified Starch and Different Molecular Weight Polyvinyl Alcohols on Biodegradable Characteristics of Polyvinyl Alcohol/Starch Blends

The common biodegradable properties of polymer make them an excellent pair for blending, and the water solubility of polyvinyl alcohol (PVA) makes it easy to mix evenly with the starch. In this study, PVAs with different molecular weights were blended with various compositions of cross-linked starch (CLS) to explore the effects of molecular weight of PVA on the biodegradable characteristics of the PVA/starch blends. Comparing the biodegradability of all the various PVA/starch blends, a PVA was singled out from the PVA/starch blends of higher biodegradability. Further, the chosen PVA was then blended with the acid-modified starch (AMS) to systematically investigate the effects of the modified processing of starch on the biodegradable characteristics of the PVA/starch blends. Differential scanning calorimetry (DSC) analysis of PVA and PVA/starch specimens reveal that the T_m values of PVA/starch specimens reduce gradually as their CLS or AMS contents increase. After the CLS is blended in PVAs of different molecular weights, the tensile strength (??_f) and elongation at break (??_f) values of (P₁₀₀S₀)G₂₀M₁ specimen increase and simultaneously reduce, respectively, as their molecular weights of PVA increase from about 80,000 (PVA_BF-17) to 120,000 (PVA_BF-26). The ??_f and ??_f values of the PVA/modified-starch blends decrease with an increase in the modified starch contents. The ??_f values of the PVA/AMS specimens decrease with an increase in the concentrations of hydrochloric acid. Comparing the ??_f values of the PVA/CLS specimens with those of the PVA/AMS specimens, the ??_f values of the PVA/CLS specimens are better than those of the PVA/AMS specimens. On the contrary, the ??_f values of the PVA/AMS specimens are better than those of the PVA/CLS specimens. According to the biodegradability of all the PVA/starch blends, PVA with higher molecular weights displays higher biodegradability. The biodegradability of the PVA/modified-starch blends increase as the modified starch contents of the PVA/modified-starch blends increase. As evidenced by the results of the biodegradability test, the biodegradability of the PVA/modified-starch blends, therein PVA is blended with 1N AMS, shows better biodegradability. The result of bio-reaction kinetics experiment can evaluate the decomposition tendency of the PVA/starch blends up to any biodegradable rate under ambient environment. Using the kinetic model of the first order reaction, it is estimated that 16.20?years and 12.47?years will be needed for the PVA_BF-17/starch blends, containing 20 and 40% of CLS respectively, to be degraded up to 70% under ambient environment. In addition, it is 1.68?years for the PVA_BF-26 blends with the 40% 2N AMS under decomposition environment while it is 1.94?years for the 40% 1N AMS. Overall, the decomposition potential of PVA/AMS specimens is better than PVA/CLS specimens. Furthermore, the 1N(26P₆₀AS₄₀)₁₀₀G₂₀M₁ specimen is coincidence the biodegradable material criteria of Environmental Protection Administration (EPA) of Taiwan.     

Processing and Thermal Behaviors of Poly (Butylene Succinate) Blends with Highly-Filled Starch and Glycerol

Fully-biodegradable and highly-filled thermoplastic starch plasticized with glycerol (GTPS)/poly (butylene succinate) (PBS) blends were prepared by Haake Mixer. Processing properties, thermal behaviors including melting and crystallization behavior, crystal structure, and compatibility of the blends were investigated using differential scanning calorimeter (DSC), wide angle X-ray diffractometer (WAXD), scanning electron microscopy (SEM) and dynamic mechanical analysis (DMA). The maximum and equilibrium torques decreased with the rising of glycerol contents and the dropping of PBS contents. GTPS30/PBS blends exhibited double melting endothermic peaks in the DSC thermograms, which related to the crystallization behavior and compatibility of the blends, but no double peaks for GTPS40/PBS. The addition of starch and glycerol could lead to higher crystallinity and lower crystallization rate of PBS, but would not change the crystal types and crystallite sizes of PBS according to DSC and WAXD analysis. SEM and DMA results gave the evidence to confirm the better compatibility of GTPS40/PBS. Besides, higher storage modulus in glassy state of GTPS/PBS blends than PBS could be seen from DMA analysis, which was the contrary in rubbery state.     

Tailored Natural Polysaccharides Beads as Green Sorbents for Efficient Lysozyme Adsorption

Herein, we prepared alginate (SA)/carboxymethyl cellulose (CMC) gel beads through Ca²⁺ and glutaraldehyde (GA) crosslinking and investigated their adsorption performance on lysozyme from aqueous solution. Taking advantage of the abundant active carboxyl groups on SA and CMC, the obtained SA/CMC gel beads present an excellent integrated lysozyme adsorption performance with a high capacity of 236.34 mg g^?1, short equilibrium time of 8 h, ease of elution, and good reusability. Furthermore, the resultant SA/CMC gel beads also possess unique selectivity for positively charged proteins, confirmed by the method of sodium dodecyl sulfate polyacrylamide gel electrophoresis. Considering the nature of biopolymers and advantages of favorable physical properties, high efficiency, cost-effectiveness, intriguing adsorption capacity and easier separation from the reaction system, the SA/CMC gel beads may find more potential in protein separation and purification than that of synthetic material.     

Utilization of Waste Lignin and Hydrolysate From Chromium Tanned Waste in Blends of Hot-Melt Extruded PVA-Starch

The demand for biodegradable plastic material is increasing worldwide. However, the cost remains high in comparison with common forms of plastic. Requirements comprise low cost, good UV-stability and mechanical properties, as well as solubility and water uptake lead to the preparation of multi-component polymer blends based on polyvinyl alcohol and starch in combination with waste products that are hard to utilize—waste lignin and hydrolysate extracted from chromium tanned waste. Surprisingly the addition of such waste products into PVA gives rise to blends with better biodegradability than commercial PVA in an aquatic aerobic environment with non-adapted activated sludge. These blends also exhibited greater solubility in the water and UV stability than commercial PVA. Tests on the processing properties of the blends (melt flow index, tensile strength and elongation at break of the films) as well as their mechanical properties showed that materials based on these blends might be applied in agriculture (for example as the systems for controlled-release pesticide or fertilizer) and, somewhat, in the packaging sector.     

Mechanical and Barrier Properties of Biodegradable Films Made from Chitosan and Poly (Lactic Acid) Blends

Biodegradable film blends of chitosan with poly(lactic acid) (PLA) were prepared by solution mixing and film casting. The main goal of these blends is to improve the water vapor barrier of chitosan by blending it with a hydrophobic biodegradable polymer from renewable resources. Mechanical properties of obtained films were assessed by tensile test. Thermal properties, water barrier properties, and water sensitivity were studied by differential scanning calorimeter analysis, water vapor permeability measurements, and surface-angle contact tests, respectively. The incorporation of PLA to chitosan improved the water barrier properties and decreased the water sensitivity of chitosan film. However, the tensile strength and elastic modulus of chitosan decreased with the addition of PLA. Mechanical and thermal properties revealed that chitosan and PLA blends are incompatible, consistent with the results of Fourier transform infrared (FTIR) analysis that showed the absence of specific interaction between chitosan and PLA.     

Preparation and Properties of Green Composites Based on Tapioca Starch and Differently Recycled Paper Cellulose Fibers

Green composites obtained from biodegradable renewable resources have gained much attention due to environmental problems resulting from conventionally synthetic plastics and a global increasing demand for alternatives to fossil resources. In this work we used different cellulose fibers from used office paper and newspaper as reinforcement for thermoplastic starch (TPS) in order to improve their poor mechanical, thermal and water resistance properties. These composites were prepared by using tapioca starch plasticized by glycerol (30 % wt/wt of glycerol to starch) as matrix reinforced by the extracted cellulose fibers with the contents ranging from 0 to 8 % (wt/wt of fibers to matrix). Properties of composites were determined by mechanical tensile tests, differential scanning calorimetry, thermogravimetric analysis, water absorption measurements, scanning electron microscopy, and soil burial tests. The results showed that the introduction of either office paper or newspaper cellulose fibers caused the improvement of tensile strength and elastic modulus, thermal stability, and water resistance for composites when compared to the non-reinforced TPS. Scanning electron microscopy showed a good adhesion between matrix and fibers. Moreover, the composites biological degraded completely after 8 weeks but required a longer time compared to the non-reinforced TPS. The results indicated that these green composites could be utilized as commodity plastics being strong, inexpensive, plentiful and recyclable.     

Grafting of Glycidyl Methacrylate onto Poly(lactide) and Properties of PLA/Starch Blends Compatibilized by the Grafted Copolymer

Poly(lactide)-graft-glycidyl methacrylate (PLA-g-GMA) copolymer was prepared by grafting GMA onto PLA in a batch mixer using benzoyl peroxide as an initiator. The graft content was determined with the ¹H-NMR spectroscopy by calculating the relative area of the characteristic peaks of PLA and GMA. The result shows that the graft content increases from 1.8 to 11.0 wt% as the GMA concentration in the feed varies from 5 to 20 wt%. The PLA/starch blends were prepared by the PLA-g-GMA copolymer as a compatibilizer, and the structure and properties of PLA/starch blends with or without the PLA-g-GMA copolymer were characterized by SEM, DSC, tensile test and medium resistance test. The result shows that the PLA/starch blends without the PLA-g-GMA copolymer show a poor interfacial adhesion and the starch granules are clearly observed, nevertheless the starch granules are better dispersed and covered by PLA when the PLA-g-GMA copolymer as a compatibilizer. The mechanical properties of the PLA/starch blends with the PLA-g-GMA copolymer are obviously improved, such as tensile strength at break increasing from 18.6 ± 3.8 MPa to 29.3 ± 5.8 MPa, tensile modulus from 510 ± 62 MPa to 901 ± 62 MPa and elongation at break from 1.8 ± 0.4 % to 3.4 ± 0.6 %, respectively, for without the PLA-g-GMA copolymer. In addition, the medium resistance of PLA/starch blends with the PLA-g-GMA copolymer was much better than PLA/starch blends.     

Lyotropic Liquid Crystal Phases in Cellulose Acetate Phthalate/Hydroxypropyl Cellulose Blends

Cellulose and some of its derivatives form liquid crystalline solutions in a variety of solvents. The present work investigates cellulose acetate phthalate/hydroxypropyl cellulose blends in N,N-dimethylacetamide, in function of concentration and composition, by rheology, considering dynamic viscometry and oscillatory shear tests. The effects of composition, concentration, shear rate, and oscillatory deformation on the rheological functions determines the orientation or mobility of the chain segments in the shear field. Atomic force microscopy and polarized light microscopy studies on corresponding films show that specific interactions, such as the hydrogen bonds between cellulose acetate phthalate and the liquid crystalline component—hydroxypropyl cellulose, stabilizes the morphology, leading to the emergence of different formations typical for lyotropic liquid crystal phases. These studies contribute to a better knowledge of the specific interactions that generate and modify the liquid crystalline properties of cellulose derivatives, required by the applications in electronic domains.     

Desiccation of contaminant barrier materials amended with aqueous carboxymethyl cellulose solution

The stabilization potential of negatively charged sodium carboxymethyl cellulose (CMC) solution was assessed through investigation of its retention on clays under environmental conditions that promote soil desiccation. Sodium montmorillonite and kaolinite, commonly used in clayey soils, were mixed with aqueous CMC solutions in concentrations ranging from 0 to 10 g/L. These samples were dried in a specially-designed desiccation chamber which was operated at a temperature of 25°C and relative humidity of 30%. The results show an inverse proportionality between liquid loss and CMC concentration. Liquid loss from clayey soil follows the first-order reaction with a rate constant in the range of 4.6–6.7 mg/h. CMC half-lives on sodium montmorillonite during desiccation ranged from 103 to 181 h for an aqueous concentration range of 0.5–10 g/L compared to 108 h for distilled water. For kaolinite, more liquid was retained at 10 g/L CMC concentration than at other concentrations, but liquid retention was generally insignificant. These conclusions are valid for a desiccation duration of 890 h, a time that is reasonably simulative of the duration of exposures of bare ground surfaces to weather elements. The experimental results are explained in terms of the role of CMC molecular interactions with clay minerals in controlling fluid flow to desiccating clay surfaces.     

Potential of <Emphasis Type="Italic">pinhão</Emphasis> Coat as Constituents of Starch Based Films Using Modification Techniques

The potential of lignocellulosic fibers obtained by dry grinding of pinhão coat as fillers in starch filmogenic solutions for packaging applications was evaluated in this work. To improve the incorporation of this waste into the starch solutions different physical and chemical treatments were conducted. Thereafter, morphology, chemical structure, crystallinity and water absorption of the pinhão coat powders were determined. The composites were also characterized regarding their morphology, chemical structure, crystallinity, mechanical properties, water vapor permeability and hydrophilicity. Poor fiber/matrix adhesion and high water absorption of the fibers were evidenced. Consequently, water vapor permeability of composites was increased by incorporating the fibers. Moreover, mechanical properties were improved and the morphological results were used to support the water absorption differences among the powders. Regarding the food packaging applications, starch/pinhão coat composites appeared as promising materials to reach the requirements of respiring food products.