Single drop microextraction and gas chromatography–mass spectrometry for the determination of diflufenican, mepanipyrim, fipronil, and pretilachlor in water samples

An analytical method for the determination of diflufenican, mepanipyrim, pretilachlor, and fipronil in water samples was developed using single drop microextraction in the direct immersion mode and gas chromatography–mass spectrometry. A factorial fractionated design of type 2^6–1 at two levels was performed, to study the influence of experimental variables such as ionic strength, pH, agitation speed, extraction time, drop volume, and sample volume. To establish the optimal conditions for the variables that were significant, a Doehlert design was performed. The optimum conditions of extraction were 1 μL of heptane immersed in 4.0 mL of sample with continuous agitation at 500 rpm for 30 min at room temperature. The developed method proved to have good linearity for the range studied. The detection limits were 0.07 μg L^?1 for diflufenican, 0.03 μg L^?1 for mepanipyrim, 0.08 μg L^?1 for pretilachlor, and 1.39 μg L^?1 for fipronil. The method was validated on river water samples, showing the absence of matrix effect and recoveries ranged from 90.1 to 107.8 %. The results show that the method developed is accurate, sensitive, rapid, simple, and low cost, so it is recommended for application in the analysis of these different classes of pesticides in water samples.     

Flow injection online spectrophotometric determination of uranium after preconcentration on XAD-4 resin impregnated with nalidixic acid

In this work, spectrophotometer was used as a detector for the determination of uranium from water, biological, and ore samples with a flow injection system coupled with solid phase extraction. In order to promote the online preconcentration of uranium, a minicolumn packed with XAD-4 resin impregnated with nalidixic acid was utilized. The system operation was based on U(VI) ion retention at pH 6 in the minicolumn at flow rate of 15.2 mL min^?1. The uranium complex was removed from the resin by 0.1 mol dm^?3 HCl at flow rate of 3.2 mL min^?1 and was mixed with arsenazo III solution (0.05 % solution in 0.1 mol dm^?3 HCl, 3.2 mL min^?1) and driven to flow through cell of spectrophotometer where its absorbance was measured at 651 nm. The influence of chemical (pH and HCl (as eluent and reagent medium) concentration) and flow (sample and eluent flow rate and preconcentration time) parameters that could affect the performance of the system as well as the possible interferents was investigated. At the optimum conditions for 60 s preconcentration time (15.2 mL of sample volume), the method presented a detection limit of 1.1 μg L^?1, a relative standard deviation (RSD) of 0.8 % at 100 μg L^?1, enrichment factor of 30, and a sample throughput of 42 h^?1, whereas for 300 s of the preconcentration time (76 mL of sample volume), a detection limit of 0.22 μg L^?1, a RSD of 1.32 % at 10 μg L^?1, enrichment factor of 150, and a sampling frequency of 11 h^?1 were reported.     

Coupling of solvent-based de-emulsification dispersive liquid–liquid microextraction with high performance liquid chromatography for simultaneous simple and rapid trace monitoring of 2,4-dichlorophenoxyacetic acid and 2-methyl-4-chlorophenoxyacetic acid

A simple, rapid, and efficient sample pretreatment technique, based on solvent-based de-emulsification dispersive liquid–liquid microextraction (SD-DLLME), followed by high performance liquid chromatography (HPLC) has been developed for simultaneous preconcentration and trace detection of 2,4-dichlorophenoxyacetic acid (2,4-D) and 2-methyl-4-chlorophenoxyacetic acid (MCPA) in water and urine samples. Some parameters such as acidity of solution, the amount of salt, type, and volume of extraction solvents, type of disperser/de-emulsifier solvent, and its volume were investigated and optimized. Under optimum extraction conditions, the limits of detections (LODs) of this method for MCPA and 2,4-D were 0.2 and 0.6 μg L^?1 (based on 3S_b/m) in water and 0.4 and 1.6 μg L^?1 in urine, respectively. Furthermore, dynamic linear range of this method for MCPA and 2,4-D was 1–300 and 2–400 μg L^?1, repectively. Finally, the applicability of the proposed method was evaluated by extraction and determination of the herbicides in urine and different water samples.     

Application of cold-induced aggregation microextraction as a fast,simple, and organic solvent-free method for the separation and preconcentration of Se(IV) in rice and various water samples

The developed method is based on cold-induced aggregation microextraction of Se(IV) using the 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid as an extractant followed by spectrophotometry determination. The extraction of Se(IV) was performed in the presence of dithizone as the complexing agent. In this method, a very small amount of 1-butyl-3-methylimidazolium hexafluorophosphate was added to the sample solution containing Se-dithizone complex. Then, the solution was kept in a thermostated bath at 50 °C for 4 min. Subsequently, the solution was cooled in an ice bath and a cloudy solution was formed. After centrifuging, the extractant phase was analyzed using a spectrophotometric detection method. Some important parameters that might affect the extraction efficiency were optimized (HCl, 0.6 mol L^?1; dithizone, 4.0?×?10^?6 mol L^?1; ionic liquid, 100 μL). Under the optimum conditions, good linear relationship, sensitivity, and reproducibility were obtained. The limit of detection (LOD) (3S_b/m) was 1.5 μg L^?1, and the relative standard deviation (RSD) was 1.2 % for 30 μg L^?1 of Se(IV). The linear range was obtained in the range of 5–60 μg L^?1. It was satisfactory to analyze rice and various water samples.     

2-Nitroso-1-naphthol as a selective reagent for preconcentration of cobalt by vortex assisted combined with solidification of organic droplet and its determination by flame atomic absorption spectrometry

Highly rapid and selective vortex-assisted liquid–liquid microextraction based on solidification of organic drop has been used for determination of cobalt ion. 2-Nitroso-1-naphthol (2N1N) was used as a selective complexing agent to form stable cobalt–2N1N complex which can be extracted with 1-undecanol at a short time by the assistance of vortex agitator system followed by its determination using flame atomic absorption spectrometry. In vortex assisted, vigorous vortex stream as well as the vibrant effect of vortex system cause very fine droplets of extraction solvent to be produced and extraction occurred at a short time. Some parameters influencing the extraction process such as pH of samples, concentration of 2-nitroso-1-naphthol, extraction solvent volume, extraction time, ionic strength and surfactant addition, as well as interferences were evaluated in detail and optimum conditions were selected. At the optimum conditions, the calibration curve was linear in the range of 15 to 400 μg L^?1 of cobalt ions. The relative standard deviation based on ten replicate analysis of sample solution containing 50 μg L^?1 of cobalt was 3.4 %. The detection limit (calculated as the concentration equivalent to three times of the standard deviation of the blank divided by the slope of the calibration curve after preconcentration) was 5.4 μg L^?1. The accuracy of the proposed method was successfully evaluated by the analysis of certified reference materials. This selective and highly rapid method was used for determination of cobalt ions in different water samples.     

Solid-phase extraction and separation procedure for trace aluminum in water samples and its determination by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS)

In the present study, a separation/preconcentration procedure for determination of aluminum in water samples has been developed by using a new atomic absorption spectrometer concept with a high-intensity xenon short-arc lamp as continuum radiation source, a high-resolution double-echelle monochromator, and a charge-coupled device array detector. Sample solution pH, sample volume, flow rate of sample solution, volume, and concentration of eluent for solid-phase extraction of Al chelates with 4-[(dicyanomethyl)diazenyl] benzoic acid on polymeric resin (Duolite XAD-761) have been investigated. The adsorbed aluminum on resin was eluted with 5 mL of 2 mol L^-1 HNO₃ and its concentration was determined by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS). Under the optimal conditions, limit of detection obtained with HR-CS FAAS and Line Source FAAS (LS-FAAS) were 0.49 μg L^?1 and 3.91 μg L^?1, respectively. The accuracy of the procedure was confirmed by analyzing certified materials (NIST SRM 1643e, Trace elements in water) and spiked real samples. The developed procedure was successfully applied to water samples.     

Evaluation of optimal conditions for determination of low selenium content in shellfish samples collected at Todos os Santos Bay,Bahia, Brazil using HG-AFS

This work proposes a procedure for the determination of total selenium content in shellfish after digestion of samples in block using cold finger system and detection using atomic fluorescent spectrometry coupled hydride generation (HG AFS). The optimal conditions for HG such as effect and volume of prereduction KBr 10 % (m/v) (1.0 and 2.0 ml) and concentration of hydrochloric acid (3.0 and 6.0 mol L^?1) were evaluated. The best results were obtained using 3 mL of HCl (6 mol L^?1) and 1 mL of KBr 10 % (m/v), followed by 30 min of prereduction for the volume of 1 mL of the digested sample. The precision and accuracy were assessed by the analysis of the Certified Reference Material NIST 1566b. Under the optimized conditions, the detection and quantification limits were 6.06 and 21.21 μg kg^?1, respectively. The developed method was applied to samples of shellfish (oysters, clams, and mussels) collected at Todos os Santos Bay, Bahia, Brazil. Selenium concentrations ranged from 0.23?±?0.02 to 3.70?±?0.27 mg kg^?1 for Mytella guyanensis and Anomalocardia brasiliana, respectively. The developed method proved to be accurate, precise, cheap, fast, and could be used for monitoring Se in shellfish samples.     

A very sensitive flow-injection spectrophotometric determination method for iron (II) and total iron using 2′, 3, 4′, 5, 7-pentahydroxyflavone

In this study, an ultra-sensitive and highly selective, rapid flow-injection spectrophotometric method for the determination of iron (II) and total iron has been proposed. The method was based on the reaction between iron (II) and 2′, 3, 4′, 5, 7-pentahydroxyflavone in slightly acidic solution with a strong absorption at 415 nm. The carrier solution used was 1?×?10^?5 M 2′, 3, 4′, 5, 7-pentahydroxyflavone in 0.1 M HAc/Ac^? buffer solution at pH 4.5. Parameters that affect simultaneously the determination of iron (II) and interfering ions were tested. The relative standard deviation for the determination of 50 μg L^?1 iron (II) was 0.85 % (n?=?10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 3 μg L^?1, both based on injection volumes of 20 μL. The method has been successfully applied to the determination of iron (II) and total iron in water samples and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F.     

Rapid spectrophotometric determination of trace amounts of palladium in water samples after dispersive liquid–liquid microextraction

A simple, rapid, and efficient dispersive liquid–liquid microextraction method, followed by UV–Vis spectrophotometry was developed for the preconcentration and determination of Pd ions in water samples. Pd ions react with α-furildioxime (chelating agent) to form a hydrophobic complex. Various parameters were altered to study and optimize their effects on the extraction efficiency, such as pH, ligand concentration, the type and volume of extraction and dispersive solvents, extraction time, and salt concentration. Under optimized conditions, the method exhibited an enrichment factor (C _org/C _aq) of 25 and recovery more than 98 % within a very short extraction time. The linearity of the method ranged from 10 to 200 μg?L^?1. The limit of detection was 1.1 μg?L^?1. The relative standard deviation for the concentration of 100 μg?L^?1 of Pd was 2.3 % (n?=?10). Finally, the developed method was successfully applied to the extraction and determination of Pd in tap, river, mineral, and sea water samples.     

Seasonal perspective of dietary arsenic consumption and urine arsenic in an endemic population

Exposure to arsenic in arsenic endemic areas is most remarkable environmental health challenges. Although effects of arsenic contamination are well established, reports are unavailable on probable seasonal variation due to changes of food habit depending on winter and summer seasons, especially for endemic regions of Nadia district, West Bengal. Complete 24-h diets, drinking–cooking water, first morning voided urine samples, and diet history were analyzed on 25 volunteers in arsenic endemic Chakdah block of Nadia district, once in summer followed by once in winter from the same participants. Results depicted no seasonal variation of body weight and body mass index. Arsenic concentration of source drinking and cooking water decreased (p?=?0.04) from 26 μg L^?1 in summer to 6 μg L^?1 in winter season. We recorded a seasonal decrease of water intake in male (3.8 and 2.5 L day ^?1) and female (2.6 and 1.2 L day^?1) participants from summer to winter. Arsenic intake through drinking water decreased (p?=?0.04) in winter (29 μg day^?1) than in summer (100 μg day^?1), and urinary arsenic concentration decreased (p?=?0.018) in winter (41 μg L^?1) than in summer (69 μg L^?1). Dietary arsenic intake remained unchanged (p?=?0.24) over the seasons. Hence, we can infer that human health risk assessment from arsenic needs an insight over temporal scale.     

The use of rapidly synergistic cloud point extraction for the separation and preconcentration of trace amounts of Ni (II) ions from food and water samples coupling with flame atomic absorption spectrometry determination

A novel improved preconcentration method known as rapidly synergistic cloud point extraction (RS-CPE) was established for nickel preconcentration and determination prior to its determination by flame atomic absorption spectrometry. In this work, the traditional CPE pattern was changed and greatly simplified in order to be applicable in metal extraction and detection. This method was accomplished in room temperature in 1 min. Non-ionic surfactant Triton X-114 was used as extractant. Octanol worked as cloud point revulsant and synergic reagent. The various parameters affecting the extraction and preconcentration of nickel such as sample pH, 2,2′-Furildioxime concentration, amounts of octanol, amounts of Triton X-114, type of diluting solvent, extraction time, and ionic strength were investigated and optimized. Under optimal conditions, the calibration curve showed an excellent linearity in the concentration range of 2–200 μg L^?1, and the limit of detection was 0.6 μg L^?1 for nickel. The developed method was successfully applied for the determination of nickel in food and water samples. The results showed that, the proposed method can be used as a cheap, rapid, and efficient method for the extraction and preconcentration of nickel from real samples.     

Voltammetric trace determination of mercury using plant refuse modified carbon paste electrodes

Citrus limon peel (kitchen waste) and Leucaena leucocephala seeds (agricultural waste) were used as a modifier for fabrication of modified carbon paste electrode for determination of mercury in aqueous sample using differential pulse anodic stripping voltammetry. Mercury was adsorbed on electrode surface at open circuit and anodic stripping voltammetric scan was run from ?0.5 to 0.5 V. Various electrochemical parameters including amount of modifier, supporting electrolyte, accumulating solvent, pH of the accumulating solvent, and accumulation time were investigated. The effect of presence of other metal ions and surfactants was also studied. In comparison C. limon peel proved to be a better modifier than L. leucocephala seed biomass. This was justified by electrode characterization using cyclic voltammetry that indicated decrease in resistance of electrode when C. limon peel was used as modifier and increase when modifier was L. leucocephala seeds. Maximum current response was obtained using 5 % C. limon peel biomass, hydrochloric acid as supporting electrolyte, acetate buffer of pH 6 as an accumulating solvent, 10-min accumulation time, and scan rate of 50 mV/s. Linear calibration curves were obtained in the concentration range 100 to 1,000 μg L^?1 of mercury for accumulation time of 10 min with limit of detection of 57.75 μg L^?1 and limit of quantification of 192.48 μg L^?1. This technique does not use mercury as electrode material and, therefore, has a positive environmental benefit.     

Impacts of climate-induced changes on the distribution of pesticides residues in water and sediment of Lake Naivasha, Kenya

This study reports evidence of increased chlorpyrifos contamination in sediment and water in Lake Naivasha following its intensive application in the horticultural farms in the catchment area. Analytical results show that levels of chlorpyrifos residues were influenced by climate-induced rainfall pattern with higher levels reported during period of heavy precipitation with significant decrease during low rainfall. On average, the levels ranged between 14.8 and 32.8 ng g^?1 in sediment during rainy season compared to a range of 8.5–16.6 ng g^?1 in the dry season. Additionally, the mean concentration of chlorpyrifos in water ranged between 8.61 and 22.4 μg L^?1 during rainy season and below detection limit (bdl) ?13.6 μg L^?1 in dry season as quantified by enzyme-linked immunosorbent assay. Meanwhile, independent t test analysis indicated that there was significant difference in concentration at p?≤?0.05 between the seasons with respect to sediment and water samples. This demonstrated that climate-induced variations had considerable influence on contamination. While diazinon and carbofuran were equally applied intensively, their levels were below the detection limit in the all the samples analyzed. ELISA results were validated by the capillary-HPLC photodiode-array detector instrument analysis, and statistical comparison showed no significant difference between them. It was evident that chlorpyrifos residues determination in water and sediment by ELISA can be a useful strategy in environmental management and monitoring program, and a complimentary analytical tool to high performance liquid chromatography. Levels of chlorpyrifos detected in sediment and water were found to exceed recommended criteria for protection of aquatic life and preservation of water quality and may be hazardous if not regularly monitored.     

Hazard assessment of metals in invasive fish species of the Yamuna River,India in relation to bioaccumulation factor and exposure concentration for human health implications

Monitoring of heavy metals was conducted in the Yamuna River considering bioaccumulation factor, exposure concentration, and human health implications which showed contamination levels of copper (Cu), lead (Pb), nickel (Ni), and chromium (Cr) and their dispersion patterns along the river. Largest concentration of Pb in river water was 392 μg L^?1; Cu was 392 μg L^?1 at the extreme downstream, Allahabad and Ni was 146 μg L^?1 at midstream, Agra. Largest concentration of Cu was 617 μg kg^?1, Ni 1,621 μg kg^?1 at midstream while Pb was 1,214 μg kg^?1 at Allahabad in surface sediment. The bioconcentration of Cu, Pb, Ni, and Cr was observed where the largest accumulation of Pb was 2.29 μg kg^?1 in Oreochromis niloticus and 1.55 μg kg^?1 in Cyprinus carpio invaded at Allahabad while largest concentration of Ni was 174 μg kg^?1 in O. niloticus and 124 μg kg^?1 in C. carpio in the midstream of the river. The calculated values of hazard index (HI) for Pb was found more than one which indicated human health concern. Carcinogenic risk value for Ni was again high i.e., 17.02?×?10^?4 which was larger than all other metals studied. The results of this study indicated bioconcentration in fish due to their exposures to heavy metals from different routes which had human health risk implications. Thus, regular environmental monitoring of heavy metal contamination in fish is advocated for assessing food safety since health risk may be associated with the consumption of fish contaminated through exposure to a degraded environment.     

Assessment of cylindrospermopsin toxin in an arid Saudi lake containing dense cyanobacterial bloom

This study reports the presence of the cyanobacterial toxin cylindrospermopisn (CYN) and its producer Cylindrospermopsis raciborskii for the first time in Saudi freshwater sources. C. raciborskii was found in Gazan Dam Lake water with two morphotypes (coiled and straight). The appearance and cell density of this species was significantly positively related to high temperature and high ammonium concentrations, and negatively with nitrate and phosphate concentrations in the lake. Intracellular concentrations of CYN (4–173 μg L^?1) were associated with C. raciborskii rather than other cyanobacteria with a maximal value obtained in June 2011, coinciding with the highest bloom of this species (19?×?10⁷ trichome L^?1). CYN cell quotas (0.6–14.6 pg cell^?1) varied significantly along the study period and correlated with most environmental factors. The results of ELISA and liquid chromatography-mass spectrometry proved that the CYN production by strains of this species was isolated from this lake during the present study, with an amount reaching 568 μg g^?1. Extracellular CYN was also detected in cell-free lake water at concentrations 0.03–23.3 μg L^?1, exceeding the drinking water guideline value of 1 μg L^?1 during the Apr–Jul period. As this lake is an important source for drinking and irrigation waters, CYN monitoring should be included in the environmental and health risk assessment plans of these water bodies.     

FIA-coupled spectrophotometric method for determination of Cr (VI) traces in natural waters: application of in-line dissolution of 1,5-diphenylcarbazide after heat treatment and activated alumina as adsorbent for preconcentration

This work proposes the quantification of Cr (VI) ions in natural waters in trace level, using activated alumina (Al₂O₃) as preconcentration support, controlled in-line dissolution of the solidified chromophore diphenylcarbazide after heat treatment and spectrophotometric detection. The manifold ensures high sensitivity of analytical response, good repeatability, and stability. In this work, optimization of experimental conditions of a flow injection system was chosen as the parameters for greater sensitivity and better selectivity. The selected optimized conditions were 0.30 mol L^?1 for H₂SO₄ concentration, system flow rate as 0.40 mL min^?1, sample injection volume of 192.50 μL, 2 min for preconcentration time, and 0.10 mol L^?1 for eluent concentration. The analytical curves obtained for real sample analysis show linear range from 0.192 to 0.961 μM, linear correlation coefficient R?=?0.9997 and LOD?=?0.024 μM. The preconcentration factor of about four times was obtained through the passage of 800 μL of a standard solution containing 0.961 μM of Cr (VI) through mini-column of preconcentration followed by elution at 192.5 μL of NH₄OH 0.1 mol L^?1 solution. The solid chromogenic reagent presented high durability (weeks in daily use with mass of 0.0993 g) and good reproducibility in analytical signal. The reactivation of the mini-column of alumina should be executed after ten injections of eluent, using 800 μL of HCl 0.02 mol L^?1 solution in flow through the same. Each cycle of injection and elution of the sample takes about 5 min on the proposed terms. Despite the length of each cycle still be high, low concentrations can be detected using a technique of relatively low cost. This is due in part, the association dissolution of the chromogenic reagent directly in the line and the preconcentration step. Another important factor is the economy of reagent chromogenic, low generation of reject contributing to better quality of the environment, and the high potential for applications to work in field.     

Mapping of fluoride endemic area and assessment of F−1 accumulation in soil and vegetation

The prevalence of fluorosis is mainly due to the consumption of more fluoride (F^?1) through drinking water, vegetables, and crops. The objective of the study was mapping of F^?1 endemic area of Newai Tehsil, Tonk district, Rajasthan, India. For the present study, water, soil (0–45 cm), and vegetation samples were collected from 17 villages. Fluoride concentration in water samples ranged from 0.3 to 9.8 mg/l. Out of 17 villages studied, the amounts of F^?1 content of eight villages were found to exceed the permissible limits. Labile F^?1 content and total F^?1 content in soil samples ranges 11.00–70.05 mg/l and 50.3–179.63 μg g^?1, respectively. F^?1 content in tree species was found in this order Azadirachta indica 47.32–55.76 μg g^?1 > Prosopis juliflora 40.16–49.63 μg g^?1 > Acacia tortilis 34.39–43.60 μg g^?1. While in case of leafy vegetables, F^?1 content order was Chenopodium album 54.23–98.42 μg g^?1 > Spinacea oleracea 30.41–64.09 μg g^?1 > Mentha arvensis 35.48–51.97 μg g^?1. The order of F^?1 content in crops was found as 41.04 μg g^?1 Pennisetum glaucum > 13.61 μg g^?1 Brassica juncea > 7.98 μg g^?1 Triticum sativum in Krishi Vigyan Kendra (KVK) farms. Among vegetation, the leafy vegetables have more F^?1 content. From the results, it is suggested that the people of KVK farms should avoid the use of highly F^?1 containing water for irrigation and drinking purpose. It has been recommended to the government authority to take serious steps to supply drinking water with low F^?1 concentration for the fluorosis affected villages. Further, grow more F^?1 hyperaccumulator plants in F^?1 endemic areas to lower the F^?1 content of the soils.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Spectrophotometric determination of platinum(IV) in alloys, complexes, environmental, and pharmaceutical samples using 4-[N,N-(diethyl)amino] benzaldehyde thiosemicarbazone

4-[N,N-(Diethyl)amino] benzaldehyde thiosemicarbazone (DEABT) is proposed as an analytical reagent for the spectrophotometric determination of platinum(IV). The DEABT forms 1:2 yellow complex with Pt(IV), which is sparingly soluble in water and completely soluble in water–ethanol–DMF medium. The Pt(IV)–DEABT complex shows maximum absorbance at 405 nm. Beer’s law is valid up to 7.80 μg cm^???3, and optimum concentration range for the determination of platinum(IV) is 0.48–7.02 μg cm^???3. The molar absorptivity and Sandell’s sensitivity of the method are found to be 1.755 × 10⁴ dm³ mol^???1 cm^???1 and 0.0012 μg cm^???2, respectively. The relative error and coefficient of variation (n?=?6) for the method does not exceed ±0.43% and 0.35%, respectively. Since the method tolerates a number of metal ions commonly associated with platinum, it can be employed for the determination of platinum in environmental samples, pharmaceutical samples, alloys, catalysts, and complexes. The method is rapid as the Pt(IV)–DEABT complex is soluble in water–ethanol–DMF medium and not requiring any time consuming extraction method for the complex.     

A nanosilver-based spectrophotometric method for determination of malachite green in surface water samples

A new spectrophotometric method is reported for the determination of nanomolar level of malachite green in surface water samples. The method is based on the catalytic effect of silver nanoparticles on the oxidation of malachite green by hexacyanoferrate (III) in acetate–acetic acid medium. The absorbance is measured at 610 nm with the fixed-time method. Under the optimum conditions, the linear range was 8.0?×?10^?9–2.0?×?10^?7?mol?L^?1 malachite green with a correlation coefficient of 0.996. The limit of detection (S/N?=?3) was 2.0?×?10^?9?mol?L^?1. Relative standard deviation for ten replicate determinations of 1.0?×?10^?8?mol?L^?1 malachite green was 1.86 %. The method is featured with good accuracy and reproducibility for malachite green determination in surface water samples without any pre-concentration and separation step.