南京市大气颗粒物中多环芳烃变化特征

逐月采集南京市大气中不同粒径的颗粒物,采用HPLC分析了2010年每个月PM_(10)和PM_(2.5)颗粒物样品中的多环芳烃(PAHs)的种类和浓度水平。结果表明:PM_(10)中PAHs年均值为25.07 ng/m~3,范围为11.03~53.56 ng/m3;PM_(2.5)中PAHs年均值为19.04 ng/m~3,范围为10.82~36.43 ng/m~3。PM_(10)和PM_(2.5)中PAHs总体浓度有着相似的变化趋势,呈现凹形变化曲线;在南京市大气颗粒物中吸附的PAHs大部分以5~6环的高环数组分为主,大部分PAHs和∑PAHs的相关性较好,年度变化幅度不大,分析结果表明,颗粒物中PAHs的来源与稳定的排放源相关,机动车排放不容忽视,与北方城市燃煤污染有着较大的区别。     

某石化化工行业聚集区室内外PM2.5中多环芳烃分布特征及来源

于非采暖季和采暖季分别采集某石化化工行业聚集城市中心城区室内外PM_(2.5)样品,采用高效液相色谱法分析PM_(2.5)上载带的16种PAHs,对其分布特征、来源以及室外PAHs污染对室内污染的贡献进行了初步探讨。结果表明,研究区域非采暖季和采暖季室外PM_(2.5)中ΣPAHs浓度日均值分别为36.3、294 ng/m~3,室内PM_(2.5)中ΣPAHs浓度分别为14.8、84.6 ng/m~3,均以4、5环PAHs为主;室内PAHs主要来自室外渗透污染,但同时明显存在室内排放源贡献;PAHs来源分析进一步证实研究区域PAHs主要来自煤炭、石油等不完全燃烧,采暖季煤炭燃烧源贡献更突出。     

淮南市PM_(2.5)中PAHs污染特征及来源分析

通过采集淮南市6个功能区四季的PM_(2.5)样品,运用GC-MS仪测定样品中PAHs含量并分析其主要来源。结果表明:该市PM_(2.5)中PAHs质量浓度年均值为31.06 ng/m~3,呈现冬季污染程度最重,夏季最轻,采矿区商业区工业区文教区居民区对照区的特征;夏季PAHs以3环和4环为主,春、秋、冬季以4环、5环和6环为主;6个功能区均以4环PAHs为主;PAHs主要来源为煤燃烧、机动车尾气排放、生物质燃烧及焦炉挥发,其中燃煤和机动车尾气污染贡献最大。     

贵阳市大气细颗粒物中多环芳烃时空分布特征

对贵阳市不同功能区在不同季节大气PM_(2.5)中多环芳烃(PAHs)进行了采样观测,利用UVD和FLD双检测器串联HPLC法分析了16种优控PAHs。结果显示,在贵阳市主城区PM_(2.5)中PAHs有检出,5个采样点全年ρ(∑PAHs)为4. 44～114 ng/m~3,平均值为24. 96 ng/m~3,其值呈现出夏季最低冬季最高的特征,各个功能区在不同季节ρ(PAHs)不同,大小趋势也不同;四季PAHs单体中均以4-6环为主,占ρ(∑PAHs)的68%以上; PAHs来源解析结果显示,贵阳市大气PM_(2.5)中PAHs来源具有明显的季节特征,春、夏和秋季主要来源是石油燃烧排放,兼有少量的生物质燃烧排放,冬季PAHs主要来源是燃煤和石油燃烧排放。PM_(2.5)中PAHs毒性评价结果表明,贵阳市大气中PAHs的春季、夏季和秋季健康风险较小,冬季健康风险较大。四季各功能区ρ(Ba P)大部分均低于《环境空气质量标准》(GB 3095—2012)规定限值(2. 50 ng/m~3),但冬季除背景点外,其他监测点均超标,最大超标倍数为3. 80倍。     

乌鲁木齐市冬季大气颗粒物PM_(10) 和PM_(2.5)污染水平及相关性研究

为研究乌鲁木齐市冬季采暖期间大气颗粒物污染特征,通过采样和在线监测二种手段分析了2015年1~2月大气颗粒物样品,采用重量法分析颗粒物质量浓度,并对其相关性进行分析。结果表明:依据《环境空气质量标准》(GB 3095-2012),采样期间乌鲁木齐市大气PM_(10) 和PM_(2.5)的日均质量浓度均超过了国家二级标准,颗粒物污染严重;PM_(10) 和PM_(2.5)存在显著相关性,PM_(2.5)和PM_(10) 浓度的比值均大于0.5,采暖期PM2.5对乌鲁木齐市大气颗粒物贡献显著。     

沈阳市大气PM2.5中多环芳烃的污染特征及来源解析

采用气相色谱-质谱联用仪定量分析2016年沈阳市PM_(2.5)中16种多环芳烃(PAHs)的质量浓度,探讨其时空分布特征,并解析PAHs的来源。结果表明:沈阳市PAHs的平均质量浓度为71. 5 ng/m3,其中3环、4环PAHs分别占31. 3%和48. 8%;采暖期PAHs浓度明显高于非采暖期,中心城区高于周边。总毒性当量浓度平均值为8. 05 ng/m3。特征比值法和主成分分析法解析的PAHs来源基本一致,主要为燃烧源、石油挥发源和工业生产源,贡献率分别为70. 11%、14. 19%和10. 74%。     

鞍山市城区采暖期大气PM_(2.5)中PAHs的污染特征研究

通过对鞍山市(1个工业区、2个工业区周边、3个居住区、1个对照点)2015年1月采暖期大气PM_(2.5)中多环芳烃(PAHs)的监测,采用BaP当量致毒系数TEF,分析了鞍山市大气PM_(2.5)中典型PAHs毒性当量分布特征。研究表明,鞍山市大气PM2.5中工业区及工业区周边Ba P毒性当量浓度要远高于居住区和对照点,污染物主要由4~6环的PAHs组成,很强致癌BaP当量浓度为9.351~38.59 ng/m3。     

交通限行对大气颗粒物及PM_(2.5)中二■英的影响

为了研究北京大气颗粒物和二■英(PCDD/Fs)的污染状况以及评估交通限行对大气颗粒物和PCDD/Fs的影响。利用同位素稀释高分辨率气相色谱/高分辨率质谱(HRGC/HRMS)联用法和USEPA 1613B标准方法,以中国地质大学(北京)东门为采样点,采集大气PM_(2.5)、PM_(10)、TSP样品,对北京市交通限行期间以及交通限行前后等不同交通状况下颗粒物浓度及大气PM_(2.5)中17种2,3,7,8-PCDD/Fs污染特征进行了监测。结果表明,PM_(2.5)、PM_(10)、TSP的日均质量浓度在交通限行前分别为126、202、304μg/m~3,限行期间分别为39、78、93μg/m~3,限行结束后分别为79、126μg/m~3。PM_(2.5)中17种PCDD/Fs的质量浓度(毒性浓度) 3个时段分别为1 804 fg/m~3(70 fg I-TEQ/m~3)、252 fg/m~3(9 fg I-TEQ/m~3)和1 196 fg/m~3(48 fg I-TEQ/m~3)。北京市交通限行期间颗粒物浓度和二■英浓度显著低于交通限行前后,交通源减排措施的实施是大气颗粒物和二■英污染水平降低的主要原因,从减排效果看,交通源减排措施对大气细颗粒物(PM_(2.5))的控制效果明显好于大气粗颗粒物。     

重庆市主城区二次有机碳气溶胶污染特征研究

为研究重庆市大气PM_(2.5)中二次有机气溶胶污染特征,于2013年1—12月运用URG-3000ABC型中流量颗粒物采样仪连续同步采集重庆市主城区大气PM_(2.5)样品,选取OC/EC比值对PM_(2.5)中的SOC污染进行估算,结果表明,该市主城区PM_(2.5)中SOC年平均质量浓度为12.5μg/m3,占OC质量浓度的50.0%,占PM_(2.5)质量浓度的10.1%,SOC质量浓度为冬季秋季夏季春季。机动车排放是SOC前体物的主要来源。     

南通市环境空气细颗粒物中多环芳烃的污染特征及来源

用玻璃纤维滤膜采集PM_(2.5)样品,乙腈超声提取-高效液相色谱法分析测量多环芳烃浓度。结果表明:PAHs的浓度变化受到大气降水的影响,夏季浓度最低,冬季浓度最高,PM_(2.5)中PAHs总量月平均变化趋势呈"凹"形变化;PAHs的结构以2~3环、5~6环为主;比值法显示PAHs来源与稳定的排放源相关,机动车排放不容忽视,与北方城市燃煤污染有着较大区别。     

Source analysis of particulate matter associated polycyclic aromatic hydrocarbons (PAHs) in an industrial city in northeastern China

Particle-associated polycyclic aromatic hydrocarbon (PAH) concentrations were investigated at eight sampling sites during cold periods where heating is used (heating period) (February to March, 2005) and warm periods where heating is not required (non-heating periods) (August to September 2006) in the urban area of Anshan, an iron and steel city in northeastern China. Eleven PAH species were measured using GC-MS. The total average concentrations of PAHs ranged from 46.14 to 385.60 ng m(-3) in the heating period and from 5.28 to 146.40 ng m(-3) in the non-heating period. The lowest concentration of ∑PAHs was observed at Qianshan, a monitoring site far from the city and industrial area, and the highest concentration occurred in the site located at the factory area of Anshan Iron and Steel Incorporation. Moreover, ambient PAH profiles were studied and high molecular weight PAH (including 4-6 rings) species occurred in the high fractions. Toxic equivalent factors analysis gave the potential carcinogenic risks in Anshan. For the heating sampling period, BaP equivalent concentration is in the range of 41.98 to 220.83 ng m(-3), and 9.23 to 126.00 ng m(-3) for the non-heating sampling period. By diagnostic ratio analysis, traffic emission and combustion (coal or biomass) were potential sources for PAHs in Anshan. Finally, PCA results indicated the major sources were vehicle emission, steel industry emission, and coal combustion for both heating and non-heating seasons, which agreed with the results from the diagnostic ratio analysis.     

克拉玛依市大气PM2.5、PM10污染水平浅析

根据从2012年1月1日至2012年3月30日在同一个监测点取得的PM2.5和PM10监测数据,分析采暖期颗粒物污染水平特征。结果表明,PM2.5浓度和PM10浓度之间高度线性相关;克拉玛依市冬季空气环境中PM2.5是PM10中的主要组成成分;PM2.5浓度在一天内基本保持稳定,而PM10浓度在一天之中的变化幅度较大,峰值出现在中午上下班高峰期。     

Chemical compositions and sources of atmospheric PM10 in heating, non-heating and sand periods at a coal-based city in northeastern China

Mass concentrations and chemical components (18 elements, 9 ions, organic carbon [OC] and elemental carbon [EC]) in atmospheric PM(10) were measured at five sites in Fushun during heating, non-heating and sand periods in 2006-2007. PM(10) mass concentrations varied from 62.0 to 226.3 μg m(-3), with 21% of the total samples' mass concentrations exceeding the Chinese national secondary standard value of 150 μg m(-3), mainly concentrated in heating and sand periods. Crustal elements, trace elements, water-soluble ions, OC and EC represented 20-47%, 2-9%, 13-34%, 15-34% and 13-25% of the particulate matter mass concentrations, respectively. OC and crustal elements exhibited the highest mass percentages, at 27-34% and 30-47% during heating and sand period. Local agricultural residuals burning may contribute to EC and ion concentrations, as shown by ion temporal variation and OC and EC correlation analysis. Heavy metals (Cr, Ni, Zn, Cu and Mn) from coal combustion and industrial processes should be paid attention to in heating and sand periods. The anion/cation ratios exhibited their highest values for the background site with the influence of stationary sources on its upper wind direction during the sand period. Secondary organic carbon were 1.6-21.7, 1.5-23.0, 0.4-17.0, 0.2-33.0 and 0.2-21.1 μg m(-3), accounting for 20-77%, 44-88%, 4-77%, 8-69% and 4-73% of OC for the five sampling sites ZQ, DZ, XH, WH and SK, respectively. From the temporal and spatial variation analysis of major species, coal combustion, agricultural residual burning and industrial emission including dust re-suspended from raw material storage piles were important sources for atmospheric PM(10) in Fushun at heating, non-heating and sand periods, respectively. It was confirmed by principal component analysis that coal combustion, vehicle emission, industrial activities, soil dust, cement and construction dust and biomass burning were the main sources for PM(10) in this coal-based city.     

Atmospheric polycyclic aromatic hydrocarbons in an industrialized city, Kocaeli, Turkey: study of seasonal variations, influence of meteorological parameters and health risk estimation

Ambient gas and particle phase samples were collected during two sampling periods from a residential area of an industrialized city, Kocaeli, Turkey. The sampling occurred during winter months when structures were being heated, and summer months when structures were not being heated. Σ(13)PAH (gas + particle) concentrations ranged between 6.2 ng m(-3) (DahA) and 98.6 ng m(-3) (Phe) in the heating (winter) period and 3.0 ng m(-3) (BaA) and 35.1 ng m(-3) (Phe) in the non-heating (summer) period. Phe, Flt and Pyr were found to be at high concentrations in both sampling periods. Winter time to summer time concentration ratios for individual ambient PAH concentration ratios ranged between 1.2 (DahA) and 17.5 (Flu), indicating the effect of the emissions from residential heating on measured concentrations of PAHs, but great industrial plants and the only incinerator facility of Turkey are other important pollution sources around the city. Temperature dependence of gas phase PAHs was investigated using the Clausius-Clapeyron equation. A high slope obtained (5069.7) indicated the effect of the local sources on measured gas phase PAHs. Correlation of the supercooled vapor pressure (P) with the gas particle partitioning coefficient (K(p)) and particle phase fraction was also evaluated. The relationship between the meteorological parameters and individual PAH (gas + particle) concentrations was investigated further by multiple linear regression analysis. It was found that the temperature had a significant effect on all of the measured PAH concentrations, while the effects of the wind speed and direction were not significant on the individual PAHs. On the other hand, PAH concentrations showed a strong linear relationship with the ventilation coefficient (VC) which showed the influence of local sources on measured PAHs. Benzo[a]pyrene toxic equivalent (BaP(eq.)) concentrations were used for health risk assessment purposes. The winter period risk level (2.92 × 10(-3)) due to the respiratory exposure to PAHs was found to be almost 3 times higher than in the summer period (1.15 × 10(-3)).     

Indoor and outdoor concentrations of fine particles, particle-bound PAHs and volatile organic compounds in Kaunas, Lithuania

This complex study presents indoor and outdoor levels of air-borne fine particles, particle-bound PAHs and VOCs at two urban locations in the city of Kaunas, Lithuania, and considers possible sources of pollution. Two sampling campaigns were performed in January-February and March-April 2009. The mean outdoor PM(2.5) concentration at Location 1 in winter was 34.5 ± 15.2 μg m(-3) while in spring it was 24.7 ± 12.2 μg m(-3); at Location 2 the corresponding values were 36.7 ± 21.7 and 22.4 ± 19.4 μg m(-3), respectively. In general there was little difference between the PM concentrations at Locations 1 and 2. PM(2.5) concentrations were lower during the spring sampling campaign. These PM concentrations were similar to those in many other European cities; however, the levels of most PAHs analysed were notably higher. The mean sum PAH concentrations at Locations 1 and 2 in the winter campaign were 75.1 ± 32.7 and 32.7 ± 11.8 ng m(-3), respectively. These differences are greater than expected from the difference in traffic intensity at the two sites, suggesting that there is another significant source of PAH emissions at Location 1 in addition to the traffic. The low observed indoor/outdoor (I/O) ratios indicate that PAH emissions at the locations studied arise primarily from outdoor sources. The buildings at both locations have old windows with wooden frames that are fairly permissive in terms of air circulation. VOC concentrations were mostly low and comparable to those reported from Sweden. The mean outdoor concentrations of VOC's were: 0.7 ± 0.2, 3.0 ± 0.8, 0.5 ± 0.2, 3.5 ± 0.3, and 0.2 ± 0.1 μg m(-3), for benzene, toluene, ethylbenzene, sum of m-, p-, o-xylenes, and naphthalene, respectively. Higher concentrations of VOCs were observed during the winter campaign, possibly due to slower dispersion, slower chemical transformations and/or the lengthy "cold start" period required by vehicles in the wintertime. A trajectory analysis showed that air masses coming from Eastern Europe carried significantly higher levels of PM(2.5) compared to masses from other regions, but the PAHs within the PM(2.5) are of local origin. It has been suggested that street dust, widely used for winter sanding activities in Eastern and Central European countries, may act not only as a source of PM, but also as source of particle-bound PAHs. Other potential sources include vehicle exhaust, domestic heating and long-range transport.     

乌鲁木齐市大气PM2.5中重金属元素含量和富集特征

利用PM2.5／PM10便携式采样器采集了乌鲁木齐市5个功能区PM2.5，样品，用TAS-990石墨炉原子吸收光谱仪检测了PM2.5样品中Cd、Cu、Ni、Pb、Mn的含量。结果表明，乌鲁木齐大气PM2.5质量浓度变化趋势是冬季采暖盛期〉秋季采暖初期〉春季停暖初期〉夏季停暖期。参照《环境空气质量标准》（GB3095—2012）中的二级标准，采样期间卡子湾水泥厂区样品全部超标，其余4个采样点样品在冬季采暖盛期也全部超标，部分样品在非采暖期超标。富集因子法分析表明，乌鲁木齐市5个采样区PM2.5样品中Ni、Cu、Cd、Pb污染主要来自于人类活动，Mn则来源于地壳物质。     

郑州大气及颗粒物中多环芳烃的分布特征与来源解析

对2012年郑州市大气中气态和颗粒态多环芳烃(PAHs)的分布特征与来源进行了分析。结果表明,ρ(∑PAHs)(包括气相与颗粒相)为23.27~194.61 ng/m3,气相中∑PAHs高于颗粒相,四环以下的PAHs大都存在于气态中;在夏、春2季,较小分子质量(≤178)的PAHs占比较高,冬季,较大分子质量(≥252)的PAHs占比明显较高;各功能区ρ(PAHs)排序为工业区交通密集区医疗、文化、行政混合区。郑州大气和颗粒物中PAHs可能主要来自煤和液体燃料(汽油柴油)的燃烧。