Trace metal fractionation in the Pichavaram mangrove–estuarine sediments in southeast India after the tsunami of 2004

The geochemistry of coastal sediments of southern India was altered after the tsunami in 2004. A five-step sequential extraction procedure was applied to assess the effects of tsunami on mobility and redistribution of selected elements (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn). Ten surface sediments and three cores were analyzed for different metal fractions (exchangeable, carbonate, reduced, oxidized, and residual). Total metal concentrations increased in mangrove sediments after the tsunami, but their spatial distribution did not show significant variation (except Mn). The sediments were mixed by the tsunami, and there was lack of variation in metal concentrations in different fractions with depth (except Pb and Mn). High concentrations of Pb and Zn occurred in the oxide fractions, whereas Cu, Cr, Cd, and Ni were high in the organic and sulfide-rich fractions. Metals in the residual fraction (lattice bound) had the highest concentration suggesting their non-availability and limited biological uptake in the system. Most of the metals (except Mn) do not constitute a risk based on the different geochemical indices.     

Vertical distribution of heavy metals in soil profile in a seasonally waterlogging agriculture field in Eastern Ganges Basin

The accumulation of heavy metals in soil and water is a serious concern due to their persistence and toxicity. This study investigated the vertical distribution of heavy metals, possible sources and their relation with soil texture in a soil profile from seasonally waterlogged agriculture fields of Eastern Ganges basin. Fifteen samples were collected at ～0.90-m interval during drilling of 13.11 mbgl and analysed for physical parameters (moisture content and grain size parameters: sand, silt, clay ratio) and heavy metals (Fe, Mn, Cr, Cu, Pb, Zn, Co, Ni and Cd). The average metal content was in the decreasing order of Fe?>?Mn?>?Cr?>?Zn?>?Ni?>?Cu?>?Co?>?Pb?>?Cd. Vertical distribution of Fe, Mn, Zn and Ni shows more or less similar trends, and clay zone records high concentration of heavy metals. The enrichment of heavy metals in clay zone with alkaline pH strongly implies that the heavy metal distributions in the study site are effectively regulated by soil texture and reductive dissolution of Fe and Mn oxy-hydroxides. Correlation coefficient analysis indicates that most of the metals correlate with Fe, Mn and soil texture (clay and silt). Soil quality assessment was carried out using geoaccumulation index (I _geo), enrichment factor (EF) and contamination factor (CF). The enrichment factor values were ranged between 0.66 (Mn) and 2.34 (Co) for the studied metals, and the contamination factor values varied between 0.79 (Mn) and 2.55 (Co). Results suggest that the elements such as Cu and Co are categorized as moderate to moderately severe contamination, which are further confirmed by I _geo values (0.69 for Cu and 0.78 for Co). The concentration of Ni exceeded the effects-range median values, and the biological adverse effect of this metal is 87 %. The average concentration of heavy metals was compared with published data such as concentration of heavy metals in Ganga River sediments, Ganga Delta sediments and upper continental crust (UCC), which apparently revealed that heavy metals such as Fe, Mn, Cr, Pb, Zn and Cd are influenced by the dynamic nature of flood plain deposits. Agricultural practice and domestic sewage are also influenced on the heavy metal content in the study area.     

Metal Pollution Assessment of Sediment and Water in the River Hindon, India

The metal pollution in water and sediment of the River Hindon in western Uttar Pradesh (India) was assessed for Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn. The metal concentrations in water showed wide temporal variation compared with bed sediment because of variability in water discharge and variations in suspended solid loadings. Metal concentrations in bed sediments provided a better evaluation of the degree and the extent of contamination in the aquatic environment, Santagarh and Atali being the most polluted sites of the river. The ratio of heavy metals to conservative elements (Fe, Al, etc.) may reveal the geochemical imbalances due to the elevated metal concentrations normally attributed to anthropogenic sources. Metal/Al ratios for the bed sediments of the river Hindon were used to determine the relative mobility and general trend of relative mobility occurred Fe > Mn > Zn > Cr > Ni > Pb > Cu > Cd.     

Statistical apportionment and risk assessment of selected metals in sediments from Rawal Lake (Pakistan)

The present study was carried out in order to evaluate the statistical apportionment and risk assessment of selected metals (Ca, Cd, Co, Cr, Cu, Fe, K, Li, Mg, Mn, Na, Pb, Sr, and Zn) in freshly deposited sediments in Rawal Lake, Pakistan. Composite sediment samples were collected, oven-dried, grounded, homogenized, and processed to assess the water-soluble and acid extractable concentrations of the metals in the water extract and acid extract of the sediments using flame atomic absorption spectrophotometer. Statistical methods were used to identify the possible sources of the metals. Sediment quality guidelines and potential acute toxicity were used to evaluate the ecotoxicological sense of selected metals. Non-carcinogenic health risk assessment was also carried out to determine the potential adverse health risks to the inhabitants. Relatively higher concentration was noted for Ca, Fe, Mg, Na, K, Mn, and Sr in the sediment samples. Principal component analysis and cluster analysis revealed anthropogenic contributions of Cd, Pb, Cr, Mn, Fe, and Li in the sediments. Enrichment factors of the metals in sediments showed severe to moderate enrichment of Cd, Pb, Ca, Fe, Li, Mn, and Sr. Geoaccumulation indices and contamination factors evidenced significant contamination by Cd and Pb, although, on the whole, low degree of contamination was noted. The levels of some metals exceeded the sediment quality guidelines, which revealed frequently adverse biological effects to the dwelling biota in the aquatic ecosystem. The sediments were found to be significantly contaminated by Cd, Pb, Cr, Mn, Fe, and Li.     

Source discrimination of heavy metals in sediment and water of To Lich River in Hanoi City using multivariate statistical approaches

The concentrations of Mn, Fe, Ni, Cr, Cu, Pb, Zn, As, and Cd were determined to evaluate the level of contamination of To Lich River in Hanoi City. All metal concentrations in 0–10-cm water samples, except Mn, were lower than the maximum permitted concentration for irrigation water standard. Meanwhile, concentrations of As, Cd, and Zn in 0–30-cm sediments were likely to have adverse effects on agriculture and aquatic life. Sediment pollution assessment was undertaken using enrichment factor and geoaccumulation index (I _geo). The I _geo results indicated that the sediment was not polluted with Cr, Mn, Fe, and Ni, and the pollution level increased in the order of Cu < Pb < Zn < As < Cd. Meanwhile, significant enrichment was shown for Cd, As, Zn, and Pb. Cluster and principal component analyses suggest that As and Mn in sediment were derived from both lithogenic and anthropogenic sources, while Cu, Pb, Zn, Cr, Cd, and Ni originated from anthropogenic sources such as vehicular fumes for Pb and metallic discharge from industrial sources and fertilizer application for other metals.     

Spatial distribution and risk assessment of heavy metals in sediments from a hypertrophic plateau lake Dianchi, China

The sediment in Dianchi Lake, a hypereutrophic plateau lake in southwest China, was investigated and the concentration of heavy metals (Cu, Cr, Ni, Zn, Pb, Fe, Mn, and Cd) in the sediment and sediment properties were determined. Their spatial distribution and sources were analyzed using multivariate statistics. The result indicated that the studied metals exhibited three distinct spatial patterns; that is, Cu, Pb, Zn, and Ni had a similar distribution, with a concentration gradient from the north to the south part of the lake; Cd and Cr presented a similar distribution; Fe and Mn presented a quite different distribution than other metals, which indicated their different sources and geochemistry processes. Correlation and cluster analysis (CA) provided origin information on these metals and the CA result was observed corresponding to those three spatial patterns. Principal component analysis further displayed metal source and driving factors; that is, Cu, Pb, Zn, Ni, Cd, and Cr were mainly derived from anthropogenic sources, and Fe and Mn were mainly the result of natural processes. Sediment assessment was conducted using geoaccumulation index (Igeo), potential ecological risk indices, and USEPA guidelines. The result indicated that, generally, Cd was the most serious risk metal; Pb and Cu posed moderate potential ecological risk; Cr, Zn, and Ni had slight ecological risk; Fe and Mn had little risk. Comparison of the assessment tools showed that each of the methods had its limitation and could bias the result, and the combined use of the methodologies and local knowledge on lithology or metal background value of soil in the practice would give a more comprehensive understanding of the metal risk or pollution. Statistical analysis also indicated that nutrients had different impacts on Fe, Mn, and trace elements, which implied that in the assessment of metal risk, nutrients impact should be taken into consideration especially for eutrophic waters.     

Speciation of metals in bed sediments and water of Qaraaoun Reservoir, Lebanon

Determination of only total element in sediments does not give an accurate estimate of the likely environmental impacts. Speciation study of metals in sediment provides information on the potential availability of metals (toxic) to biota under various environmental conditions. In water, the toxic metal specie is the free hydrated metal ion. The toxicity of metals depends especially on their chemical forms rather than their total metal content. The present study focuses on Qaraaoun Reservoir, Lebanon. Earlier studies focused only on total metal concentrations in sediment and water. The objective of this study was to determine metal speciation (Fe, Cr, Ni, Zn, Cu, Pb, Cd) in the (operationally defined) sediment chemical fractions and metal speciation in reservoir water. This would reflect on metal bioavailability and toxicity. Water samples and bed sediments were collected from nine sites during the dry season and a sequential chemical fraction scheme was applied to the <75-??m sieve sediment fraction. Metal content in each fraction was determined by the FAAS technique. The data showed that the highest percentages of total metal content in sediment fractions were for: Fe in residual followed by reducible, Cr and Ni in residual and in reducible, Cu in organic followed by exchangeable, Zn in residual and in organic, Pb in organic and carbonate, Cd was mainly in carbonate. Total metal content in water was determined by ICP-MS technique and aqueous metal speciation was predicted using AQUACHEM software interfaced to PHREEQC geochemical computer model. The water speciation data predicted that a high percentage of Pb and Ni were present as carbonate complex species and low percentages as free hydrated ions, highest percentage of Zn as carbonate complex species followed by free hydrated ion, highest percentage of Cd as free hydrated ion followed by carbonate complex species. The sensitivity attempt of free hydrated ion of Ni, Zn, Pb, and Cd in reservoir water revealed dependence of Zn and Cd on pH and alkalinity, while Ni and Pb were only dependent on pH.     

Assessment of heavy metal concentration in the Khoshk River water and sediment, Shiraz, Southwest Iran

Heavy metal contents and contamination characteristics of the water and sediment of the Khoshk River, Shiraz, Southwest Iran were investigated. The abundance of heavy metals decreases as Zn > Mn > Cr > Ni >Pb > Cu > Cd in water samples and Mn > Cr > Pb > Ni > Zn > Cu > Cd in sediments, respectively. Based on the enrichment factor and geoaccumulation index values, sediments were loaded with Cr, Zn, Pb, Cu, and Cd. Pearson correlation matrix as well as cluster and principal components analyses and analysis of variance were implemented on data from sampling sites. Based on the locations of sampling sites in clusters and variable concentrations at these stations, it was concluded that municipal, industrial, and domestic discharges in the Shiraz urban area strongly affected heavy metals concentrations in the Khoshk River water and sediment. Results obtained from principal components analysis of sediment samples showed that the high concentration of Ni was mainly from natural origin, related to the composition of parent rocks, while the elevated values of Cr, Zn, Pb, Cd, and Cu were due to anthropogenic activities.     

Heavy metal concentrations in water, suspended matter, and sediment from Gökova Bay, Turkey

The contents of heavy metals (Fe, Mn, Pb, Cu, Cd, and Hg) dissolved in water and suspended solids of Gökova Bay—partly and fully sampled in 2005 and 2006, respectively—are quite higher than the average values encountered in uncontaminated sea water. The high concentrations are associated with terrestrial inputs from the mining zones and anthropogenic (domestic + industrial) sources. Moreover, the distribution of Fe and Cu is affected by primary production because these elements function as nutrients in biological activities. The Cr, Ni, and Fe concentrations of surface sediments are above the shale average. The Cr and Ni contents of surface sediments representative of river mouths strongly correlate with total phosphorus contents. In a sulfide-poor environment, Pb and Cu were concentrated at a higher ratio in surface sediments than Cd, probably due to higher stabilities of their surface complexes with amorphous iron oxides and clay minerals existing as major components in the sediments. The exceptional enrichment of Zn may be attributed to double oxide formation with amorphous iron oxides in sediments. The high metal values are most probably caused by terrestrial inputs from anthropogenic sources and the mining zones at the southeast part of the bay. The Al, Mn, Pb, Cu, Zn, and Hg contents are below the shale average. The low values have possibly originated from the coarse-grained sandy sediments having a low affinity for metals. There are no distinct differences in the metal distributions in water and suspended matter between the years 2005 and 2006 in the bay, probably due to low sedimentation rates.     

Determination of heavy metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn) by ICP-OES and their speciation in Algerian Mediterranean Sea sediments after a five-stage sequential extraction procedure

Surface sediment samples (n = 18) were collected from the Algerian Mediterranean coasts and analyzed for seven metals using inductively coupled plasma-optical emission spectrometry in order to asses the distribution and bioavailability of metals and to study the anthropogenic factors affecting their concentrations. Sediment samples were size-fractionated into three sizes: 1,080–500 (coarse), 500–250 (medium), and <250 mm (fine). Bulk sediments were subjected to both sequential extraction and total digestion to evaluate the reliability of the sequential extraction procedure (SEP), while the fractions have been only sequentially extracted for metals speciation. The metals were sequentially extracted into five phases namely exchangeable (P1), carbonates (P2), Fe–Mn oxides (P3), organic (P4) and residual (P5). Metal recoveries in sequential extractions were ±20% of the independently measured total metal concentrations; the high recovery rates indicate the good reliability of the SEP used in this study. Correlation coefficients indicated that the grain size has an effect on the distribution of metals in the investigated samples. The order of metal levels in the fractions was medium > fine > coarse for all the metals. The average total extractable metal concentrations for Cd, Cr, Cu, Fe, Ni, Pb, and Zn were 1.1, 8.8, 4.7, 1,291.3, 13.9, 5.7 and 20.4 μg/g, respectively. The northeastern shelf had the lowest metal levels while the highest were in northwestern part mainly due to the significant tourism activities in the northwestern part. Comparison of our results to Earth’s crust values and to previous studies points out that our samples were relatively unpolluted with respect to the heavy metals investigated; most of the metals are not from anthropogenic sources. Enrichment factors as the criteria for examining the impact of the anthropogenic sources of heavy metals were calculated, and it was observed that the investigated samples were not contaminated with Cr, Cu, and Fe, moderately contaminated with Ni, Pb, and Cd, and contaminated with Cd in some sites. The P5 phase had the highest percents of Cr, Cu, Fe, Ni, and Zn. Cadmium and lead were predominant in the P4 phase, while Cu, Fe and Zn were distributed in the order P5 > P3 > P4 > P2 > P1. The following order of bioavailability was found with the heavy metals Pb > Cr > Cd > Ni > Zn > Cu > Fe.     

Pollution in the urban soils of Lianyungang,China, evaluated using a pollution index,mobility of heavy metals,and enzymatic activities

Soil samples from 16 urban sites in Lianyungang, China were collected and analyzed. A pollution index was used to assess the potential ecological risk of heavy metals and a sequential extraction procedure was used to evaluate the relative distribution of Cu, Zn, Pb, Cd, Cr, and As in exchangeable, carbonate, Fe/Mn oxide, organic/sulfide, and residual fractions. The mobility of heavy metals and urease (URE) activity, alkaline phosphatase (ALP) activity, and invertase (INV) activity of soils was determined. The results showed that the average concentrations of Cu, Zn, Pb, Cd, Cr, and As in Lianyungang soils were much higher than those in the coastal city soil background values of Jiangsu and China. Among the five studied regions (utilities, commercial, industrial, tourism, and roadside), the industrial region had the highest metal concentrations demonstrating that land use had a significant impact on the accumulation of heavy metals in Lianyungang soils. Compared to the other metals, Cd showed the highest ecological risk. According to chemical partitioning, Cu was associated with the organic/sulfides and Pb and Zn were mainly in the carbonate and the Fe/Mn oxide phase. The greatest amounts of Cd were found in exchangeable and carbonate fractions, while Cr and As were mainly in the residual fraction. Cd had the highest mobility of all metals, and the order of mobility (highest to lowest) of heavy metals in Lianyungang soils was Cd > Zn > Pb > Cu > As > Cr. Soil urease activity, alkaline phosphatase activity, and invertase activity varied considerably in different pollution degree sites. Soil enzyme activities had the lowest levels in roadside and industrial regions. Across all the soil data in the five regions, the total Cu, Zn, Pb, Cd, Cr, and As level was negatively correlated with urease activity, alkaline phosphatase activity, and invertase activity, but the relationship was not significant. In the industrial region, alkaline phosphatase activity had significant negative correlations with total Cu, Pb, Cr, Zn, Cd, and heavy metal fractions. This showed that alkaline phosphatase activity was sensitive to heavy metals in heavily contaminated regions, whereas urease and invertase were less affected. The combination of the various methods may offer a powerful analytical technique in the study of heavy metal pollution in street soil.     

Assessment of the Quality Characteristics of Two Lakes (Koronia and Volvi) of N. Greece

Quality parameters from 17 sampling stations from Lake Koronia and 18 from Lake Volvi were determined during sampling period of one year. Physicochemical parameters (pH, conductivity, DO) did not show remarkable differences neither between sampling sites nor between sampling periods. Nutrient concentrations (nitrogen and phosphorus compounds) were higher in lake Koronia than in Volvi showing relatively small temporal and spatial variations. As far as heavy metals in sediments, lake Koronia is considerably more polluted than Volvi lake especially with the metals Fe, Mn, Zn, Pb and Cd. The mean total concentrations of metals in lake Koronia decrease in the order Mn > Zn > Cr > Pb > Cu > Fe > Cd. The mean total concentrations of metals in lake Volvi decrease in the order Mn > Zn > Cr > Cu > Pb > Fe $>$ Cd.     

Chemometric study on the trace metal accumulation in the sediments of the Cochin Estuary―Southwest coast of India

The distribution and accumulation of trace metals in the sediments of the Cochin estuary during the pre-monsoon, monsoon and post-monsoon periods were investigated. Sediment samples from 14 locations were collected and analysed for the metal contents (Mg, Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb), organic carbon, total nitrogen, total sulphur and grain size. The data were processed using statistical tools like correlation, factor and cluster analysis. The study revealed an enrichment of Cd and Zn in the study area particularly at station 2, which is confirmed by enrichment factor, contamination factor and geoaccumulation index. The factor analysis revealed that the source of Cd and Zn may be same. The study indicated that the spatial variation for the metals like Mg, Cr, Fe, Co, Ni, Cu, Zn, Cd and Pb were predominant unlike Mn which shows a temporal variation. The strong association of trace metals with Fe and Mn hydroxides and oxides are prominent along the Cochin estuary. The anthropogenic inputs of industrial effluents mainly control the trace metals enrichment in the Cochin estuary.     

贵州煤矿区表层水-沉积物重金属分布特征及来源分析——以新寨河为例

为探索贵州煤矿区表层水-沉积物中重金属的分布特征及来源,科学制定环境保护与污染治理措施,以新寨河为研究对象,在11个样点共采集66个表层水体和沉积物样品,通过对Cd、Pb、Cr、Zn、Cu、As、Hg、Fe、Mn等9种重金属元素进行分析,揭示其在新寨河的空间分布特征。同时,利用多指数法开展了有毒重金属元素污染状况评价,通过相关性分析和主成分分析解析了重金属的来源。结果表明,新寨河流域表层水体中,Fe、Mn点位超标率达100%。表层水中重金属元素的平均含量排序为Fe＞Mn＞Zn＞Cu＞Cr＞As＞Cd＞Pb＞Hg,而沉积物中重金属元素的平均含量排序则是Fe＞Mn＞Zn＞Cr＞Cu＞As＞Pb＞Cd＞Hg,表明新寨河表层水体和沉积物中重金属元素的空间分布存在一定差异。各重金属元素的内梅罗综合污染指数介于0.59~1.13之间,表明新寨河表层水体中重金属的污染程度达到轻微污染水平。单种重金属元素的潜在生态危害系数计算结果显示,90.91%和9.09%的沉积物样点分别被归类为轻微风险和中等风险。所有样点沉积物的潜在生态危害指数介于14.57~120.55之间(均值为72.08),表明新寨河沉积物的潜在生态风险较低。Cu、As在多个样点存在污染现象,需予以重点监控管理。新寨河流域重金属的来源可分为三大类:Cd、Pb、Cr、Zn、Cu为第一类,对应地表径流源;As、Fe、Mn为第二类,对应煤矿开采源;Hg为第三类,对应复合源。     

Assessment of heavy metal pollution of seston from freshwater resources poured into the Northeast Mediterranean region

This study was carried out to determine the accumulation levels of heavy metals (Zn, Cd, Pb, Cu, Fe, Cr) in seston to three different freshwater resources poured into the Iskenderun Bay. Seasonal averages of physico-chemical parameters measured at stations, Arsuz Stream, Payas Stream, and Ceyhan River, are classified as Class III—contaminated water according to the temperature parameter in the summer. Payas Stream has been determined to be Class III—polluted water according to pH parameters during the summer season. Ceyhan River was found to be Class III—contaminated water according to the dissolved oxygen parameter in the autumn season. Heavy metal accumulation levels in the seston were determined Fe?>?Cr?>?Zn?>?Cu?>?Pb?>?Cd in Arsuz Stream, Fe?>?Zn?>?Pb?>?Cr?>?Cu?>?Cd in Payas Stream, and Fe?>?Zn?>?Cr?>?Cu?>?Pb?>?Cd in Ceyhan River. The results in this study showed that high accumulation levels in seston were determined for Fe while low accumulation levels for Cd.     

Heavy Metal Levels in Biota and Sediments in the Northern Coast of the Marmara Sea

Concentration of Cd, Co, Cr, Ni, Zn, Fe, Mn, Pb and Cu were determinedin biota and sediment samples collected from the Marmara Sea in Turkey. The levels of Zn, Fe, Mn, Pb and Cu in the macroalgae are higher than previous studies in the Marmara Sea. Moreover, Cu and Zn concentrations at the present study are significantly high than Bosphorus and Black Sea algae. The order heavy metal concentrations in the mussel samples was: Fe > Zn > Ni > Mn > Cu > Pb > Cr > Cd > Co. The metal concentrations are generally lower when compared with the Black Sea mussels except Pb. At the same time, concentrations of Pb, Cu and Zn in the mussel species are lower when compared with the results in the Aegean Sea. The ranges of Mn and Cu in the tested fish samples are higher than Black Sea fish. On the other hand, Cd, Co, Cr, Zn and Pb concentrations are lower. The northern coast of the Marmara Sea having the highest metal concentrations in sediments as follows: Co, Cr, Ni, Fe at ?arköy ; Pb, Cu at M. Ere?li; Cd, Zn, Mn at Menek?e. The heavy metal levels in the sediment samples are lower than other areas in the Marmara Sea.     

Total and Leachable Heavy Metals in Muddy and Sandy Sediments of Egyptian Coast Along Mediterranean Sea

The assessment of marine pollution due to metals was made for surficial sediments sampled from 20 sites along Mediterranean coast of Egypt. The samples were dried, acid digested and analyzed for leachable and total heavy metal contents (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) by flame atomic absorption spectrophotometer (air–acetylene) with deuterium background correction. Evaluation of the heavy metals pollution status was carried out using enrichment factors (EFs), the effect range-low (ERL) and the effect range-median (ERM). The study showed high concentrations of Cd, Co, Pb, Ni and moderate concentrations of Cr, Cu and Mn were contaminated in the sediments of studied sites. The results of Spearman correlation, factor and cluster analysis of the heavy metals analyzed in the collected sediment were discussed. The main source of contamination is the offshore oil field and industrial wastes, which arise due to the ineffective and inefficient operation equipments, illegal discharge and lack of supervision and prosecution of offenders.     

Studies on heavy metals in the ground waters of the city of Aligarh U.P. (India)

A study was conducted to determine the levels of heavy metals Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn along with physico-chemical parameters in ground waters of Aligarh city, U.P. (India). Twenty seven samples of hand pump water and twenty three samples of municipal water supply were collected from different localities of the Aligarh city, five times during the period of two months at intervals of 12 days. The samples were analysed for physico-chemical characteristics (pH, electrical conductivity, chlorides, sulphates, total hardness, total alkalinity, nitrate-nitrogen, fluoride, calcium and magnesium) and heavy metal contents. The concentrations of heavy metals in the hand pump water samples were found in the ranges of Cd (ND-5.00); Cr (ND-30.00); Cu (ND-82.50); Fe (16.80–460.00); Mn (ND-425.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (28.60–775.00) g l^–1. The heavy metal concentrations in the municipal water supply samples were found to be Cd (ND-5.00); Cr (ND-25.00); Cu (ND-37.50); Fe (8.00–37.50); Mn (ND-320.00); Ni (ND-25.00); Pb (ND-25.00) and Zn (2.00–271.87) g l^–1.It appears from the results of these studies the concentrations of Cd, Cr, Cu, Ni, Pb, and Zn in the ground waters of the Aligarh City were found to be lower than the prescribed limits of World Health Organisation (1984), whereas the values of Fe and Mn were found above the prescribed limits in some localities. The chloride total hardness and nitrate-nitrogen were comparatively higher in the hand pump water than the municipal supply water. The reason of higher values of these parameters may be ascribed to the surface disposal of sewage wastes, wastes from metal processing industries and other house hold refuses.     

Assessment of metal enrichments in tsunamigenic sediments of Pichavaram mangroves, southeast coast of India

The 26 December 2004-Tsunami has deposited sediments in the Pichavaram mangrove ecosystem, east coast of India. Ten surface and three core sediment samples were collected within thirty days of the event. High concentrations of Cd, Cu, Cr, Pb, and Ni were observed in the tsunamigenic sediments. With respect to Fe, Zn, and Mn, there was little variation as compared to pre-tsunami values. The geo-accumulation index was calculated in order to assess the contamination of heavy metals in the sediments. The sediments were extremely contaminated with respect to Cd and they showed moderate to strong contamination with respect to Cr, Pb and Ni. The study highlighted the future risk of enhanced metal pollution in near future in this mangrove ecosystem.     

Fractionation and ecological risk of metals in urban river sediments in Zhongshan City, Pearl River Delta

Surface sediments collected from nine urban rivers located in Zhongshan City, Pearl River Delta, were analyzed for total concentration of metals with digestion and chemical fractionation adopting the modified European Community Bureau of Reference (BCR) sequential extraction procedure. The results showed that concentration and fractionation of metals varied significantly among the rivers. The total concentration of eight metals in most rivers did not exceed the China Environmental Quality Standard for Soil, Grade III. The potential ecological risk of metals to rivers were related to the land use patterns, in the order of manufacturing areas > residential areas > agriculture areas. The concentration of Pb in the reducible fraction was relatively high (60.0-84.3%). The dominant proportions of Cd, Zn and Cu were primary in the non-residual fraction (67.0%, 71.8% and 81.4% on average respectively), while the percentages of the residual fractions of Cr and Ni varied over a wide range (43-85% and 24-71% respectively). The approaches of the H?kanson ecological risk index and Secondary Phase Enrichment Factor were applied for ecological risk assessment and metal enrichment calculation. The results indicated Hg and Cd had posed high potential ecological risk to urban rivers in this region. Meanwhile, there was widespread pollution and high enrichment of Cu in river sediments in this region. Multiple regression analysis showed that five water quality parameters (pH, DO, COD(Mn), NH(4)(+)-N, TP) had little influence on the distribution of metal fractionation. This result revealed that the ecological risk of metals was not eliminated along with the improvement in water quality. Correlation studies showed that among the metals, Group A (Cd, As, Pb, Zn Hg, r = 0.730-0.924) and Group B (Cr, Cu, Ni, r = 0.815-0.948) were obtained, and the metal contaminations were from industrial activities rather than residential.