New kinetic-spectrophotometric method for monitoring the concentration of iodine in river and city water samples

A new kinetic method has been developed for the determination of iodine in water samples. The method is based on the catalytic effect of I^? with the oxidation of Indigo Carmine (IC) by KBrO₃ in the sulfuric acid medium. The optimum conditions obtained are 0.16 M sulfuric acid, 1?×?10^?3 M of IC, 1?×?10^?2 M KBrO₃, reaction temperature of 35°C, and reaction time of 80 s at 612 nm. Under the optimized conditions, the method allowed the quantification of I^? in a range of 12–375 ng/mL with a detection limit of 0.46 ng/mL. The method was applied to the determination of iodine in river and city water samples with the satisfactorily results.     

Utility of cefixime as a complexing reagent for the determination of Ni(II) in synthetic mixture and water samples

A simple, sensitive, and accurate UV spectrophotometric method has been developed for the determination of nickel in synthetic mixture and water samples. The method is based on the complexation reaction of nickel ion with cefixime, thus leading to the formation of Ni–cefixime complex in ethanol-distilled water medium at room temperature. The complex showed the maximum absorption wavelength at 332 nm. Beer’s law is obeyed in the working concentration range of 0.447–4.019 μg?mL^?1 with apparent molar absorptivity of 7.314?×?10³?L?mol^?1?cm^?1 and Sandell’s sensitivity of 0.008 μg/cm²/0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.016 and 0.054 μg?mL^?1, respectively. The factors such as cefixime concentration and solvent affecting the complexation reaction were carefully studied and optimized. The method is validated as per the International Conference on Harmonisation guideline. The method is successfully applied to the determination of Ni(II) in synthetic mixture and wadi water samples collected from Al Rustaq. The same water samples are also analyzed by atomic absorption spectrophotometry. Both methods determined the amount of Ni(II) in water sample and found to be approximately the same.     

Rapid spectrophotometric determination of trace amounts of palladium in water samples after dispersive liquid–liquid microextraction

A simple, rapid, and efficient dispersive liquid–liquid microextraction method, followed by UV–Vis spectrophotometry was developed for the preconcentration and determination of Pd ions in water samples. Pd ions react with α-furildioxime (chelating agent) to form a hydrophobic complex. Various parameters were altered to study and optimize their effects on the extraction efficiency, such as pH, ligand concentration, the type and volume of extraction and dispersive solvents, extraction time, and salt concentration. Under optimized conditions, the method exhibited an enrichment factor (C _org/C _aq) of 25 and recovery more than 98 % within a very short extraction time. The linearity of the method ranged from 10 to 200 μg?L^?1. The limit of detection was 1.1 μg?L^?1. The relative standard deviation for the concentration of 100 μg?L^?1 of Pd was 2.3 % (n?=?10). Finally, the developed method was successfully applied to the extraction and determination of Pd in tap, river, mineral, and sea water samples.     

Validation of spectrophotometric method for Se(IV) determination: analytical applications

As selenium is an important part of the antioxidant enzymes and also because there are several studies suggesting a possible link between cancer and selenium deficiency, this paper presents a spectrophotometric method for the assay of Se(IV), using N,N-diethyl-p-phenylenediamine monohydrochloride as reagent. The proposed method is based on the reaction between the selenium and potassium iodide in low acidic medium, when iodine is released. This last product will further oxidise the new reagent. The final obtained product is strongly coloured in red and has an absorption maximum at 552 nm and molar extinction coefficient (ε) of 6.1?×?10⁴ L mol^?1 cm^?1. The optimum working conditions were established, and the developed method was validated, being characterised by a good linearity (in the range of 0.5–3.0 μg/mL), a limit of detection (0.0573 μg/mL) and a limit of quantification (0.1737 μg/mL). At the same time, the repeatability, the precision of the method and the accuracy were established. The proposed and validated method was applied with good results for the determination of Se(IV) in spring and bottled water from Iasi and also in pharmaceutical and cosmetic products.     

Application of zirconium–iridium permanent modifier for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry

A novel and robust method for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry was developed, using zirconium–iridium coating as permanent modifier (140 μg Zr and 4 μg Ir). After 300 atomization cycles, it was necessary to add 2 μg of Ir. Due to the varying concentrations of Pb in atmospheric particulate matter, lead was monitored at two wavelengths, at the less sensitive line of 261.4 nm for high concentration samples (>20 μg?L^?1) or at 283.3 nm for the low concentration samples. Matrix-matched calibration had to be performed for quantitative recoveries (96–102 %). Following this approach, the four elements were determined in atmospheric particulate matter samples from an industrial area near the city of Athens in two different time periods (cold–warm) with limits of detection of 5.5 ng?m^?3 for Pb at 261.4 nm and 0.29 ng?m^?3 at 283.3 nm, 0.019 ng?m^?3 for Cd, 0.14 ng?m^?3 for As, and 0.22 ng?m^?3 for Ni. Lead, Cd, and As levels were very low, whereas Ni content was at comparable levels with other areas worldwide.     

A very sensitive flow-injection spectrophotometric determination method for iron (II) and total iron using 2′, 3, 4′, 5, 7-pentahydroxyflavone

In this study, an ultra-sensitive and highly selective, rapid flow-injection spectrophotometric method for the determination of iron (II) and total iron has been proposed. The method was based on the reaction between iron (II) and 2′, 3, 4′, 5, 7-pentahydroxyflavone in slightly acidic solution with a strong absorption at 415 nm. The carrier solution used was 1?×?10^?5 M 2′, 3, 4′, 5, 7-pentahydroxyflavone in 0.1 M HAc/Ac^? buffer solution at pH 4.5. Parameters that affect simultaneously the determination of iron (II) and interfering ions were tested. The relative standard deviation for the determination of 50 μg L^?1 iron (II) was 0.85 % (n?=?10), and the limit of detection (blank signal plus three times the standard deviation of the blank) was 3 μg L^?1, both based on injection volumes of 20 μL. The method has been successfully applied to the determination of iron (II) and total iron in water samples and ore samples. The method was verified by analysing a certified reference material Zn/Al/Cu 43XZ3F.     

Single drop microextraction and gas chromatography–mass spectrometry for the determination of diflufenican, mepanipyrim, fipronil, and pretilachlor in water samples

An analytical method for the determination of diflufenican, mepanipyrim, pretilachlor, and fipronil in water samples was developed using single drop microextraction in the direct immersion mode and gas chromatography–mass spectrometry. A factorial fractionated design of type 2^6–1 at two levels was performed, to study the influence of experimental variables such as ionic strength, pH, agitation speed, extraction time, drop volume, and sample volume. To establish the optimal conditions for the variables that were significant, a Doehlert design was performed. The optimum conditions of extraction were 1 μL of heptane immersed in 4.0 mL of sample with continuous agitation at 500 rpm for 30 min at room temperature. The developed method proved to have good linearity for the range studied. The detection limits were 0.07 μg L^?1 for diflufenican, 0.03 μg L^?1 for mepanipyrim, 0.08 μg L^?1 for pretilachlor, and 1.39 μg L^?1 for fipronil. The method was validated on river water samples, showing the absence of matrix effect and recoveries ranged from 90.1 to 107.8 %. The results show that the method developed is accurate, sensitive, rapid, simple, and low cost, so it is recommended for application in the analysis of these different classes of pesticides in water samples.     

Application of cold-induced aggregation microextraction as a fast,simple, and organic solvent-free method for the separation and preconcentration of Se(IV) in rice and various water samples

The developed method is based on cold-induced aggregation microextraction of Se(IV) using the 1-butyl-3-methylimidazolium hexafluorophosphate ionic liquid as an extractant followed by spectrophotometry determination. The extraction of Se(IV) was performed in the presence of dithizone as the complexing agent. In this method, a very small amount of 1-butyl-3-methylimidazolium hexafluorophosphate was added to the sample solution containing Se-dithizone complex. Then, the solution was kept in a thermostated bath at 50 °C for 4 min. Subsequently, the solution was cooled in an ice bath and a cloudy solution was formed. After centrifuging, the extractant phase was analyzed using a spectrophotometric detection method. Some important parameters that might affect the extraction efficiency were optimized (HCl, 0.6 mol L^?1; dithizone, 4.0?×?10^?6 mol L^?1; ionic liquid, 100 μL). Under the optimum conditions, good linear relationship, sensitivity, and reproducibility were obtained. The limit of detection (LOD) (3S_b/m) was 1.5 μg L^?1, and the relative standard deviation (RSD) was 1.2 % for 30 μg L^?1 of Se(IV). The linear range was obtained in the range of 5–60 μg L^?1. It was satisfactory to analyze rice and various water samples.     

Coupling of solvent-based de-emulsification dispersive liquid–liquid microextraction with high performance liquid chromatography for simultaneous simple and rapid trace monitoring of 2,4-dichlorophenoxyacetic acid and 2-methyl-4-chlorophenoxyacetic acid

A simple, rapid, and efficient sample pretreatment technique, based on solvent-based de-emulsification dispersive liquid–liquid microextraction (SD-DLLME), followed by high performance liquid chromatography (HPLC) has been developed for simultaneous preconcentration and trace detection of 2,4-dichlorophenoxyacetic acid (2,4-D) and 2-methyl-4-chlorophenoxyacetic acid (MCPA) in water and urine samples. Some parameters such as acidity of solution, the amount of salt, type, and volume of extraction solvents, type of disperser/de-emulsifier solvent, and its volume were investigated and optimized. Under optimum extraction conditions, the limits of detections (LODs) of this method for MCPA and 2,4-D were 0.2 and 0.6 μg L^?1 (based on 3S_b/m) in water and 0.4 and 1.6 μg L^?1 in urine, respectively. Furthermore, dynamic linear range of this method for MCPA and 2,4-D was 1–300 and 2–400 μg L^?1, repectively. Finally, the applicability of the proposed method was evaluated by extraction and determination of the herbicides in urine and different water samples.     

A simple extraction procedure for determination of total mercury in crude oil

The determination of mercury in crude oil and petroleum products is particularly difficult due to the volatile nature of both mercury and the matrix, which may lead to significant loss of the analyte. A simple extraction method for total mercury has been developed to determine total mercury in crude oil using cold vapor atomic fluorescence spectrometry. The homogenized crude oil sample was diluted to 5, 10, and 20 % (w/w) in toluene. The diluted crude oil samples were spiked with 10 and 40 μg/kg (w/w). The samples were extracted using an oxidant/acid solution, BrCl/HCl. The mercury was extracted into the aqueous phase; the ionic mercury was then reduced to volatile elemental mercury (Hg⁰) by stannous chloride (SnCl₂). The mercury vapor was detected by Merlin cold vapor atomic fluorescence spectrometry at a 253.7-nm wavelength. The average recoveries for mercury in spiked diluted crude oil (10 and 40 μg/kg, w/w) were between 96 and 103 %, respectively, in 5 and 10 % spiked diluted crude oil. Whereas, low recoveries (<50 %) were recorded in 20 % diluted spiked crude oil. The method detection limit was calculated as t _{(0.01)(n ? 1)}?×?SD where t is the student's value for 99 % confidence level and standard deviation estimate with n???1 degrees of freedom. The method detection limit was found to be 0.38 μg/kg based on 5 g of diluted crude oil sample. The method is sensitive enough to determine low levels of mercury in crude oil.     

Evaluation of optimal conditions for determination of low selenium content in shellfish samples collected at Todos os Santos Bay,Bahia, Brazil using HG-AFS

This work proposes a procedure for the determination of total selenium content in shellfish after digestion of samples in block using cold finger system and detection using atomic fluorescent spectrometry coupled hydride generation (HG AFS). The optimal conditions for HG such as effect and volume of prereduction KBr 10 % (m/v) (1.0 and 2.0 ml) and concentration of hydrochloric acid (3.0 and 6.0 mol L^?1) were evaluated. The best results were obtained using 3 mL of HCl (6 mol L^?1) and 1 mL of KBr 10 % (m/v), followed by 30 min of prereduction for the volume of 1 mL of the digested sample. The precision and accuracy were assessed by the analysis of the Certified Reference Material NIST 1566b. Under the optimized conditions, the detection and quantification limits were 6.06 and 21.21 μg kg^?1, respectively. The developed method was applied to samples of shellfish (oysters, clams, and mussels) collected at Todos os Santos Bay, Bahia, Brazil. Selenium concentrations ranged from 0.23?±?0.02 to 3.70?±?0.27 mg kg^?1 for Mytella guyanensis and Anomalocardia brasiliana, respectively. The developed method proved to be accurate, precise, cheap, fast, and could be used for monitoring Se in shellfish samples.     

Solid-phase extraction and separation procedure for trace aluminum in water samples and its determination by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS)

In the present study, a separation/preconcentration procedure for determination of aluminum in water samples has been developed by using a new atomic absorption spectrometer concept with a high-intensity xenon short-arc lamp as continuum radiation source, a high-resolution double-echelle monochromator, and a charge-coupled device array detector. Sample solution pH, sample volume, flow rate of sample solution, volume, and concentration of eluent for solid-phase extraction of Al chelates with 4-[(dicyanomethyl)diazenyl] benzoic acid on polymeric resin (Duolite XAD-761) have been investigated. The adsorbed aluminum on resin was eluted with 5 mL of 2 mol L^-1 HNO₃ and its concentration was determined by high-resolution continuum source flame atomic absorption spectrometry (HR-CS FAAS). Under the optimal conditions, limit of detection obtained with HR-CS FAAS and Line Source FAAS (LS-FAAS) were 0.49 μg L^?1 and 3.91 μg L^?1, respectively. The accuracy of the procedure was confirmed by analyzing certified materials (NIST SRM 1643e, Trace elements in water) and spiked real samples. The developed procedure was successfully applied to water samples.     

Flow injection online spectrophotometric determination of uranium after preconcentration on XAD-4 resin impregnated with nalidixic acid

In this work, spectrophotometer was used as a detector for the determination of uranium from water, biological, and ore samples with a flow injection system coupled with solid phase extraction. In order to promote the online preconcentration of uranium, a minicolumn packed with XAD-4 resin impregnated with nalidixic acid was utilized. The system operation was based on U(VI) ion retention at pH 6 in the minicolumn at flow rate of 15.2 mL min^?1. The uranium complex was removed from the resin by 0.1 mol dm^?3 HCl at flow rate of 3.2 mL min^?1 and was mixed with arsenazo III solution (0.05 % solution in 0.1 mol dm^?3 HCl, 3.2 mL min^?1) and driven to flow through cell of spectrophotometer where its absorbance was measured at 651 nm. The influence of chemical (pH and HCl (as eluent and reagent medium) concentration) and flow (sample and eluent flow rate and preconcentration time) parameters that could affect the performance of the system as well as the possible interferents was investigated. At the optimum conditions for 60 s preconcentration time (15.2 mL of sample volume), the method presented a detection limit of 1.1 μg L^?1, a relative standard deviation (RSD) of 0.8 % at 100 μg L^?1, enrichment factor of 30, and a sample throughput of 42 h^?1, whereas for 300 s of the preconcentration time (76 mL of sample volume), a detection limit of 0.22 μg L^?1, a RSD of 1.32 % at 10 μg L^?1, enrichment factor of 150, and a sampling frequency of 11 h^?1 were reported.     

The use of silica gel modified with allyl 6-methyl-4-phenyl-2-thioxo-1,2,3,4-tetrahydropyrimidine-5-carboxylate for selective separation and preconcentration of lead in environmental samples

The aim of the present work is the assessment of a new sorbent, prepared using silica gel coated with a pyrimidine derivative (allyl 6-methyl-4-phenyl-2-thioxo-1,2,3,4-tetrahydropyrimidine-5-carboxylate), for extraction and preconcentration trace amount of lead from different samples prior to determination by flame atomic absorption spectrometry. Common coexisting ions did not interfere with the separation and determination of lead at pH?6, so that lead ion completely adsorbed on the column. The limit of detection based on three times the standard deviation of the blank was found to be 0.53 ng?mL^?1 in original solution. Obtained sorption capacity for 1 g sorbent was 5.0 mg Pb. The linearity was maintained in the concentration range of 0.1–30.0 ng?mL^?1 for the concentrated solution. Eight replicate determinations of 2.0 μg?mL^?1 of lead in the final solution gave relative standard deviation of ±2.6 %. The proposed method was successfully applied to the determination trace amounts of lead in the environmental samples such as carrot, rice, zardchoobe, and real water samples.     

Quantification of ultra-trace amounts of copper by using off-line solid phase extraction-flame atomic absorption spectrometric determination through the octadecyl silica-bonded phase membrane (OSPM) C18 disks impregnated with 2,2'-[ethane-1,2-diylbis(thio)]dianiline

This study reports a very selective, easy, and precise method for rapid separation of trace amounts of copper in aqueous samples using octadecyl silica-bonded phase membrane disks modified by 2,2'-[ethane-1,2-diylbis(thio)]dianiline (EDTD) combined with flame atomic absorption spectrometric determination. In addition, the synthesis and spectral characterization of EDTD have been described in detail. All the affecting experimental variables such as pH, amount of modifier, eluent type, sample and eluent flow rate, interfering ions, and disk capacity were also investigated. The target analyte (trace copper) was quantitatively retained at pH?=?4 and eluted with 6.0 mL of 0.5 M HNO₃ at flow rates of 40 and 10 mL min^?1 for analyte passage and elution steps, respectively, through the disks modified with 17.0 mg of EDTD. The proposed method also allows an enrichment factor of about 500 and has a detection limit of 0.005 ng mL^?1. The method has been successfully applied for isolation and determination of copper in different water samples, peppers, and standard alloys.     

Solid phase extraction of Cd,Pb, Ni,Cu, and Zn in environmental samples on multiwalled carbon nanotubes

A simple and sensitive solid phase extraction (SPE) method on multiwalled carbon nanotubes (MWCNTs) is presented for the determination of cadmium, lead, nickel, copper, and zinc at trace levels combined with flame atomic absorption spectrometry. The effects of parameters like pH, sample volume, sample and eluent flow rates, eluent concentration, and volume and type of eluent on the recovery of trace elements was examined. The metals retained on the nanotube at pH 6.5 as α-benzoin oxime complexes were eluted by 10 mL 2 M HNO₃ in acetone. The influence of matrix ions on the developed method was also evaluated. The preconcentration factor of the method was found to be 50. The detection limits for Cd(II), Pb(II), Ni(II), Cu(II), and Zn(II) were found as 1.7, 5.5, 6.0, 2.3, and 2.4 μg L^?1, respectively. To test the accuracy of the method, the method was applied to TMDA-70 fortified lake water and Spinach 1570A standard reference materials. Addition recovery studies were applied to tap water and cracked wheat samples, and determination of the analyte elements was carried out in some food samples with good results.     

Dissipation and residues of bispyribac-sodium in rice and environment

The dissipation and residues of bispyribac-sodium in rice cropping system were studied. Bispyribac-sodium residues were extracted by a simple analytical method based on QuEChERs and detected by LC-MS/MS. The limit of detection for bispyribac-sodium of this method was 0.375?×?10^?3 ng. The limit of quantification (LOQ) was 5.0 μg/kg for rice plant samples, 2.0 μg/kg for rice hull, 0.2 μg/kg for water, and 0.1 μg/kg for soil and husked rice samples. The average recoveries of bispyribac-sodium ranged from 74.7 to 108 %, with relative standard deviations less than 13 %. The half-lives of bispyribac-sodium in rice plant, water, and soil were in the range of 1.4–5.6 days. More than 90 % of bispyribac-sodium residue dissipated within 5 days. The final residues of bispyribac-sodium in rice were all below LOQ at harvest time.     

Solid phase extraction and determination of Cr(III) by spectrophotometry using cefaclor as a complexing reagent and FAAS

The present study reports on the application of modified groundnut shell as a new, easily prepared, and stable sorbent for the extraction of trace amount of Cr(III) in aqueous solution. 2-Hydroxybenzaldiminoglycine was immobilized on groundnut shells in alkaline medium and then used as a solid phase for the column preconcentration of Cr(III). The elution was carried out with 3 mL of 2 mol?L^?1 HCl. The amount of eluted Cr(III) was determined by spectrophotometry using cefaclor as a complexing reagent and by flame atomic absorption spectrometry (FAAS). Different experimental variables such as pH, amount of solid sorbent, volume and concentration of eluent, sample and eluent flow rate, and interference of other metal ions on the retention of Cr(III) were studied. Under the optimized conditions, the calibration curves were found to be linear over the concentration range of 13–104 and 10–75 μg?L^?1 with a detection limit of 3.64 and 1.24 μg?L^?1 for spectrophotometric method and FAAS, respectively. An enrichment factor of 200 and RSD of ±1.19–1.49 % for five successive determinations of 25 μg?L^?1 were achieved. The column preconcentration was successfully applied to the analysis of tap water and underground water samples.     

Extraction of ultra traces of polychlorinated biphenyls in aqueous samples using suspended liquid-phase microextraction and gas chromatography-electron capture detection

This study reports the feasibility of applying directly suspended liquid-phase microextraction (DSLPME)-gas chromatography detection for the pre-concentration and determination of low levels of eight polychlorinated biphenyls (PCBs) in aqueous samples. The technique requires minimal sample preparation, analysis time and solvent consumption and represents significant advantages over conventional analytical methods. The experimental parameters such as salt content, sample temperature, stirring rate, extraction time, micro-drop volume and breakthrough volume were investigated and found to have significant influences on DSLPME. Under the optimal experimental conditions, the enrichment factor ranged from 578 to 729, and the recovery was above 93 %. Calibration curves possessed good linearity (R ²?>?0.99) over a wide concentration range of 0.1–10.0 μg L^?1 with limits of detection ranging from 0.01 to 0.07 μg L^?1. The relative standard deviations for 1.0 μg L^?1 of PCBs in water by using internal standard were in the range 2–14 % (n?=?3). The proposed simple, accurate and sensitive analytical method was applied successfully to the determination of trace amounts of PCBs in water samples.     

Occurrence of mycotoxins in feed samples in Burdur Province, Turkey

The aim of this study was to evaluate the incidence of total aflatoxin (AF), ochratoxin A, T-2 toxin, deoxynivalenol (DON), zearalenone (ZEA), and fumonisin (FB) in dairy cattle, beef cattle, and lamb–calf feeds. A total of 180 dairy cattle, beef cattle, and lamb–calf feeds (60 samples each) were randomly collected from farms, feed mills, and villages in Burdur province, between September 2006 and August 2007. All samples were analyzed by the competitive Enzyme Linked Immuno Sorbent Assay (ELISA). The most frequent mycotoxin detected was total AF, which was found in 108 samples (60 %) in concentrations ranging from 3.82 to 116.83 μg?kg^?1, followed by DON that was detected in 87 samples (48.3 %), in concentrations ranging from 18.50 to 500 μg?kg^?1. Ochratoxin A (OTA), T-2 toxin, ZEA, and FB were found in 84 (46.7 %), 85 (47.2 %), 57 (31.7 %), and 19 (10.6 %) samples, respectively, in concentrations of 1.01 to 15.85 μg?kg^?1 for OTA, 3.85 to 52.36 μg?kg^?1 for T-2 toxin, 2.10 to 29.30 μg?kg^?1 for ZEA, and 2.69 to 4.96 mg?kg^?1 for FB. It was concluded that feed samples in Burdur province were contaminated by mycotoxins, and the levels of total aflatoxin in the samples were considered a risk to animal health.