二氧化氯,亚氯酸根及氯酸根含量在水处理中的分析方法

二氧化氟是一种具有广阔应用前景的饮用水消毒剂，制备和使用时可能产生一系列氯的不同氧化态物质，其中最主要的是ＣｌＯ２、ＣｌＯ２和ＣｌＯ３，本研究用紫外分光光度法分别测定了ＣｌＯ２和ＣｌＯ２的含量，同时用改进的碘量法分别测定溶液中同时存在的ＣｌＯ２、ＣｌＯ２和ＣｌＯ３，并讨论了有关的反应机理，测定的精密度和准确度均满足一般饮用水质分析的需要。     

过氧化氢对COD干扰的测定

过氧化氢对ＣＯＤ干扰的测定苏惠波（黑龙江省齐齐哈尔市环境保护科学研究所，齐齐哈尔１６１００５）Ｈ２Ｏ２干扰ＣＯＤ测定，但建议不用试剂掩蔽Ｈ２Ｏ２而是允许它的存在，因为①掩蔽剂对ＣＯＤ测定会产生新的干扰；②用碘量法、硫酸铈（Ⅳ）和锰量的方法很容易测出Ｈ...     

废水COD分析的取样误差和最小重复测定次数的确定

废水ＣＯＤ分析的取样误差和最小重复测定次数的确定谢美云（福建三明市环境监测站，３６５０００）在日常监测中，发现水中悬浮物对ＣＯＤ值有一定的影响，特别是测定锅炉除尘废水，由于废水中含有大量的未燃烧完的粉煤灰，直接影响着ＯＣＤ值，当粉煤灰含量高时，ＣＯＤ...     

用膜电极法测定生化需氧量（BOD_5）

本文讨论了角膜电极测定生化需氧量（ＢＯＤ５）方法与传统碘量法的比较。两家实验室的验证结果表明，对于地表水和废水的测定，两种方法测得结果没有明显差异，用膜电极法测定ＢＯＤ５方法的精密度和准确度可以满足实际样品的测定。     

膜电极法测定BOD5

讨论了用膜电极测定生化需氧量（ＢＯＤ５）的方法，并作传统的碘量法进行了比较。数据表明，对于地表水的测定，２种方法测得结果无明显差异，用膜电极法测定ＢＯＤ５方法的精密度和准确度可以满足地表水监测的要求。     

用TOC值估算炼油废水BOD5的稀释倍数

根据ＴＯＣ与ＢＯＤ５之间的相关关系，来估算ＢＯＤ５稀释倍数，应用于炼油废水ＢＯＤ５的测定计算模型简单，操作快捷，准确。     

五日生化需氧量测定中稀释倍数的估算

假定样品经过培养后耗氧率达５５％；推导出ＢＯＤ５稀释倍数Ｋ＝ＢＯＤ５／４．４，由稀释程度规定推导出ＢＯＤ５稀释倍数Ｋ＝（ＢＯＤ５－１）／４．０两种方法Ｋ基本相同，标准样品，工业废水经上述方法稀释后，测定结果比较满意，尤其对工业废水测定，既缩短了分析时间，又降低了测定误差。     

发生氢气分离离子色谱法间接测定水中硫化物

利用ＫＢＨ４在酸性条件下分解产生的氢气为载气分离水中硫化物，用ＮａＯＨ—Ｈ２Ｏ２溶液吸收Ｈ２Ｓ，并将其氧化为ＳＯ２－４，用离子色谱法测定ＳＯ２－４。方法用于各种水样中硫化物的测定，相对标准偏差为１．５８％，回收率在９０．５％到９８．２％之间。方法适用于水中硫化物的测定     

电导返滴定法测定苯酚含量

向苯酚试液中加入定量过量的ＮａＯＨ标准溶液，用Ｈ３ＢＯ３标准溶液滴定过量的ＮａＯＨ，通过计算求得苯酚含量，测定下限为１０－５ｍｏｌ／Ｌ。并成功地测定了某化工厂废液中苯酚含量。     

医院污水中BOD测定稀释倍数的探讨

探讨了一种简便的医院污水ＢＯＤ测定中样品稀释倍数的推算方法。首先测定ＣＯＤＣｒ值，由ＣＯＤＣｒ值除以系数８，即获得稀释倍数Ｃ＝ＣＯＤＣｒ／８。结果表明，该法仅需配制一个稀释比，省时省力，并具有可靠性好，准确度高，适应性强等优点。适用于各种医院污水中ＢＯＤ的分析监测。     

Field measurement of lead in workplace air and paint chip samples by ultrasonic extraction and portable anodic stripping voltammetry

On-site measurement of lead in workplace air filter samples and paint chip samples by ultrasonic extraction and anodic stripping voltammetry (UE-ASV) was evaluated in the field during renovation and remodeling activities in residences having leaded paint. Aerosol and paint samples were collected using standard techniques, and the samples were analyzed on-site for lead content by portable UE-ASV. Lead in sample extracts was subsequently determined by atomic absorption (AA) spectrometry in a fixed-site laboratory. The remaining sample extracts plus undissolved material (air filters or paint particles) were then subjected to hot plate digestion in concentrated nitric acid-30% hydrogen peroxide prior to AA analysis for lead. Field UE-ASV lead data were thereby compared to UE-AA and hot plate digestion-AA results from fixed-site laboratory lead measurement. Determination of lead in air filter samples by UE-ASV (over the range of 5 microg to approximately 800 microg Pb per sample) was extremely well correlated with lead measurement by UE-AA and hot plate digestion-AA procedures. However, a significant negative bias associated with ASV measurement was observed, and this was attributed to a matrix effect. Lead measurement in paint chip samples by UE-ASV (over the range of approximately 10 to approximately 550 microg Pb g(-1)) was well correlated with lead measurement by UE-AA and hot plate digestion-AA procedures. However, correlation and precision were lower for lead measurement in paint samples as compared to aerosol samples, and a negative bias was also observed. Lead measurements by UE-AA were compared to lead determinations by hot plate digestion-AA; these data were highly correlated and demonstrated no significant bias. Thus it was concluded that the ultrasonic extraction procedure performed equivalently to hot plate digestion. It was reasoned that matrix effects due to the preparation and analysis of paint chip particles resulted in greater imprecision as well as negative bias by ASV measurement. Despite significant negative bias in this sample set, UE-ASV offers promise for on-site measurement of lead in samples of interest in occupational and environmental health.     

城市环境铅污染及其对人体健康的影响

综述了城市土壤和大气环境中铅的污染特征及食品和饮水中的铅污染水平,探讨了人体铅暴露的途径及城市环境铅污染对儿童健康的危害.提出应加强城市环境铅污染的调查研究,开展人体铅暴露的潜在风险评价,为保证城市居民健康安全提供科学依据.     

Ultrasonic extraction and portable anodic stripping voltammetric measurement of lead in paint, dust wipes, soil, and air: an interlaboratory evaluation

Recent studies have demonstrated the utility of ultrasonic extraction (UE), followed by portable anodic stripping voltammetry (ASV), for the on-site determination of lead in environmental and industrial hygiene samples. The aim of this work was to conduct an interlaboratory evaluation of the UE-ASV procedure, with a goal of establishing estimates of method performance based on results from collaborative interlaboratory analysis. In this investigation, performance evaluation materials (PEMs) with characterized lead concentrations were used for interlaboratory testing of the UE-ASV procedure. The UE-ASV protocol examined has been promulgated in the form of two separate national voluntary consensus standards (one for UE and another for electroanalysis, which includes ASV). The PEMs consisted of characterized and homogenized paints, soils, and dusts (the last of which were spiked onto wipes meeting national voluntary consensus standard specifications), and air filter samples (mixed cellulose ester membrane) generated using characterized paints within an aerosol chamber. The lead concentrations within the PEMs were chosen so as to bracket pertinent action levels for lead in the various sample matrices. The interlaboratory evaluation was conducted so as to comply with an applicable national voluntary consensus standard that can be used to estimate the interlaboratory precision of a given analytical test method. Based on the analytical results reported by the participating laboratories, relative standard deviations (RSDs) for repeatability and reproducibility were computed for three different lead contents of the four PEMs. RSDs for repeatability were 0.019-0.100 for paints; 0.030-0.151 for soils; 0.085-0.134 for dust wipes; and 0.095-0.137 for air filters. RSDs for reproducibility were 0.127-0.213 for paints; 0.062-0.162 for soils; 0.085-0.134 for dust wipes; and 0.114-0.220 for air filters. With the exception of one of the air filter samples and one of the paint samples, the precision estimates were within the +/- 20% precision requirement specified in the US Environmental Protection Agency National Lead Laboratory Accreditation Program (NLLAP). The results of this investigation illustrate that the UE-ASV procedure is an effective method for the quantitative measurement of lead in the matrices evaluated in this study.     

Filtration of fullerene and copper oxide nanoparticles using surface-modified microfilters

This study evaluated the filtration of engineered nanoparticles of fullerene and copper oxide (CuO) from water by using surface-modified microsized filters. The surfaces of microsized filters of cellulose acetate and glass fibers were coated with cationic and anionic surfactants to give them positively and negatively charged surfaces, respectively. Uncoated microfilters removed 30 % of a fullerene suspension, while no nanosized CuO suspension was removed. Cationic surfactant-coated filters enhanced the removal efficiency up to 70 % for the fullerene suspension, while the anionic surfactant-coated filters could not remove fullerene at all. The positively charged filters with cationic surfactant coating could easily adsorb negatively charged fullerenes on their surfaces. However, none of the surfactant-coated filters removed the CuO nanoparticles because the nanoparticles were not affected by the electrical charge of the filtration medium. The Hamaker constants of nanoparticles interacting with the filter materials in water were calculated to study these interactions. The Hamaker constant of fullerene interacting with cellulose acetate in water, 4.68E???21 J, was higher than that of interacting with quartz in water, 2.59E???21 J. However, the Hamaker constants of CuO interacting with quartz and cellulose acetate in water were both negative values, implying repulsive van der Waals interactions. The curves of potential energy of interaction between nanoparticles and the various filter media implied that the nanoparticles were very stable in water, and so, natural deposition of nanoparticles on the filters would not occur. Therefore, electrical bonding and hydrophobic interactions were the forces dominating fullerene removal by positively charged filters.     

The development of point-of-use water filters as sampling devices in bioforensics: extent of microbial sorption and elution

The foundational idea for this project is that household faucet-mounted water filters may be used as bioforensic sampling devices to detect the extent of a potential bioagent release in domestic water supplies. An optimized eluent solution was determined experimentally by quantifying recoveries of microorganisms from point-of-use (POU) drinking water filters. The optimized extraction protocol was then used in mock bioagent release experiments to determine the feasibility of POU filters as bioforensic sampling devices. Bacillus atrophaeus spores, Escherichia coli and PP7 virus were exposed to filters and the number of attached organisms was determined by enumerating the unattached organisms on selective agar media. Subsequently, the filters were eluted and the percent of extracted organisms was determined based on the number of attached organisms. Two popular brands of carbon block filters retained 92%-99% of representative virus, spore and vegetative bacteria. In back-flush elutions of single filters, the most efficient eluent was identified as a combination of 1% peptone and 1% Tween-80, and extraction recovered 25.4% (+/-17.5%) of attached E. coli, 20.4% (+/-3.6%) of B. atrophaeus spores, and 9.4% (+/-5.2%) of PP7 virions (+/- standard deviations). In bioagent release studies in which filters were challenged with 100 agents mL(-1), greater than 99% of the spores were retained by the filters, and the percent of attached spores that were recovered ranged from 10.4% at day 0 to 4.3% five days after the release event (averaged from five separate experiments). In contrast, E. coli, Salmonella typhimurium and PP7 virus were rapidly inactivated in the chlorinated tap water, indicating their improbable survival in chlorinated water supplies. It is therefore concluded that household water filters can be used as microbial sampling devices for bioforensic applications in the event of a bioagent release in domestic drinking water supplies.     

Levels of lead in atmospheric deposition in a large urban agglomeration in Poland

Lead levels in wet and dry deposition were determined within this project. A network of 10 sampling stations was established. The stations were located in areas characterized by heavy traffic volumes, but away from industrial and/or municipal pollution sources. It was assumed, therefore, that lead in the samples collected was coming primarily from automobile emissions. Measurements were carried out over a period of one year. Both rain and snow samples were collected. Lead concentrations in the samples ranged from 0.6 to 141 microg dm(-3). They depended on street topography, traffic volume, average speed of the vehicles, frequency of traffic congestion and atmospheric conditions. The highest lead levels in deposition were observed during the cold season.     

Influence of paint chips on lead concentration in the soil of public playgrounds in Tokyo

Lead concentration in the surface soils from 31 playgrounds in a ward in Tokyo was measured to examine if paint chips, peeled off from playing equipment installed in the playgrounds, contribute to elevated Pb concentration in the soil of public playgrounds. Lead concentration in the paint chips sampled from playgrounds ranged from 0.003 to 8.9%. Lead concentration in the surface soil ranged from 15.2 to 237 mg kg(-1) (average, 55.5 mg kg(-1)) and higher Pb concentration was found in the soil near painted playing equipment indicating that paint chips from playing equipment contributed to increase soil Pb level of playgrounds in Tokyo. The degree of peeling-off of paint on the surface of playing equipment in the public playground (peeling-off index: POI) positively correlated with Pb concentration in the soil (Spearman rank-correlation coefficient, r = 0.366, p = 0.043). The stronger correlation between Pb concentration and isotope ratios (207Pb/206Pb and Pb conc., r = 0.536, p = 0.002, 208Pb/206Pb and Pb conc. r = 0.600, p < 0.001) than that between Pb and POI indicated that gasoline Pb contributed more to the playground-to-playground variation in soil Pb concentration. It was concluded that both gasoline Pb of the past and paint chips contributed to increased Pb concentration in the surface soil of playgrounds in Tokyo, though the contribution of paint chips is smaller than gasoline Pb.     

流动注射-氢化物发生-原子荧光光谱法测定土壤中铅

采用流动注射-氢化物发生-原子荧光光谱法测定土壤中的铅,工作曲线线性关系良好,检出限为0.25 mg/kg,相对标准偏差＜3.5%,加标回收率为93.0%～105%.该方法简便快速,测定结果准确可靠.     

大气颗粒物手工比对监测体系滤膜称量质控技术探讨

健全大气颗粒物手工比对监测体系是"十三五"环境空气自动监测质量管理的一项重点任务,其中颗粒物滤膜的称量直接影响手工监测数据质量。研究调研了国内各级环保部门所属环境监测机构颗粒物滤膜称量工作情况,结合国内外方法标准、技术规范等,重点探讨了称量实验室环境、称量设备、称量影响因素等滤膜称量质控要点,并针对环境管理与监测需求对大气颗粒物手工比对监测滤膜称量质控提出建议。     

Application of impregnated filters to determination of smoke and ammonia

Whatman No. 1 filters impregnated with a 3% solution of oxalic acid in ethanol which are used for elimination of ammonia from the air stream before entering the absorber for collecting SO₂, were tested for a possible application (a) in the spectrophotometric determination of ammonia with Nessler's reagent and (b) in the reflectometric determination of smoke. It was shown that impregnated filters were as suitable for the determination of ammonia as absorbing solution and as applicable for smoke measurement as untreated filters. Further, the advantage of using impregnated filters for sampling ammonia lies in avoiding the interference of organic vapours which may occur, if absorbing solution is used.