环境样品稀释方法的探讨

环境样品，特别是污染源样品，在监测分析中经常要对污染物含量较高的样品进行稀释，使稀释后详品中污染物的浓度量分析方法测定浓度范围内。采取科学的稀释方法，确定适当的稀释份数，不仅可减轻分析工作量，节约分析成本，而且可降低样品中干扰物质的浓度，降低稀释误差，提高监测结果的可靠性。1样品稀释方法及其选择样品的稀释方法很多，本文便讨论根据样品稀释时使用的样品预处理程度分类。如原始样品稀释法，中同样品稀释法，分析后样品稀释法等．1．1原始样品稀释法需要稀释的环境样品中，均可采用原始样品稀释法。原始样品稀释法根…     

紫外分光光度法测定地表水中矿物油样品稀释方法的探讨

对含矿物油的地表水样，采用原始样品稀释法和分析后样品稀释法进行实验比较，结果表明，2种不同稀释方法对测定结果无显著性差异，符合监测规范要求，操作简便易行。     

盲样考核浓度预判及稀释方法——以原子荧光法测定水中砷为例

以原子荧光法测定水中砷为例,探讨了实验室盲样考核浓度预判及稀释方法.分析了3个砷盲样考核实例,归纳了“直接稀释法”“系列稀释法”“最大稀释法”3种方法,分别适用于盲样浓度范围窄、适中、宽3种情况,检测人员可根据考核机构给定的浓度范围合理选用.     

ICP-AES法和分光光度法测定工业废水中总磷的方法比较

用ICP-AES法和分光光度法同时测定4种不同工业废水中的总磷含量,将2种方法的测定结果作比对。试验表明,ICP-AES法对国家标准样品的测定结果具有较高的准确度和精密度,4种废水样品测定结果的加标回收率为94.0%~110%,RSD在0.9%~3.2%之间。分光光度法适用于低浓度、低干扰样品的测定,对于高浓度含磷废水,取样体积和样品稀释倍数均会对其测定结果产生显著影响。消解样品经浊度-色度补偿后,分光光度法的测定结果精密度较低。     

动态稀释法在汽车涂装行业固定污染源挥发性有机物测定中的应用

介绍了固定污染源中挥发性有机物(VOCs)的主要采样方法,并重点介绍了动态稀释法在固定污染源中采样的应用。采用动态稀释法取样,对某汽车企业涂装车间的排放废气进行了定性分析,并对其中主要的10种VOCs进行了定量分析。研究了方法测定的稳定性,10种化合物相对标准偏差为9%~32%,符合工况变动范围。将不同采样时间及不同吸附材料的测定结果与在线监控数据进行比较,结果显示动态稀释法的测定结果均在实际工况波动范围内,说明该方法能够较好地满足汽车涂装行业VOCs的采样要求。     

环境样品稀释方法的探讨

环境样品分析中，特别是污染源样品分析经常遇到样品浓度高于方法的检出范围。为此，根据不同分析项目的分析方法和质量控制的要求，研究和探讨了样品稀释可采用原始样品、中间样品和分析后样品进行稀释。稀释倍数可根据日常积累的基础资料推算、肉眼观察和简单试验的方法确定。探讨了稀释误差的来源及降低稀释误差的方法。     

消除水中硫酸盐测定干扰的方法

铬酸钡间接原子吸收法测定水中硫酸盐时,样品的稀释倍数、盐度、酸度对测定结果影响较大.通过试验得出消除干扰的方法,使得测定结果准确、可信.     

生化需氧量测定中稀释比的选择

1987年我国参照国际标准ISO5815-1983,采用稀释与接种方法作为测定水中生化需氧量(BOD_5)的标准方法,又称为标准稀释法.本法适用于BOD_5大于或等于2mg/L并且不超过6000mg/L的水样.当BOD_5大于6000mg/L时水样仍可采用本法测定,但由于稀释会造成误差,所以选择适当的稀释比(稀释倍数)是BOD_5测定的首要问题.标准稀释法对于测定生活污水和某些可降解的纯有机物来说,其方法稳定、重现性较好,但对于测定有机成分复杂、高浓度的各种工业废水,则存在多种因素的影响.此外,5日生化需氧量的曲线表明,只有耗氧     

水系沉积物重金属分析前处理方法

建立了水系沉积物中6种重金属分析的前处理方法,研究了样品粒径、消解前处理对测定结果的影响,对方法适用性作出评价,并对实际样品进行测定。结果表明:通过Hg元素含量的测定,粒径为0.147 mm的沉积物粒径可满足分析要求;采用微波-硝酸-盐酸-氢氟酸消解、ICP-MS法,对5种不同类型沉积物标准样品的6种重金属的测定结果显示,该方法精密度好、准确度高。利用建立的方法测定广西某河流湖库沉积物样品,6种元素测定结果 RSD为1.57%~11.1%,加标回收率大于74.4%。     

便携式GC-MS法快速测定固定污染源废气中的VOCs

采用便携式GC-MS法快速测定固定污染源废气中VOCs,32种VOCs在2×10~(-7)~1×10~(-6)范围内线性良好,方法检出限为2×10~(-9)~1×10~(-8),标准气体样品6次测定结果的RSD为1.9%~19.1%,环境空气样品的加标回收率为66.2%~116%。在实际现场监测固定污染源中VOCs时,使用速查(Survey)功能可初步判断样品浓度,确定稀释倍数。比对试验结果表明,气袋和玻璃注射器采样法对VOCs测定结果无显著性差异。     

基于智能手机比色测定水环境中的六价铬

在酸性条件下,水样中的六价铬能够和显色剂二苯碳酰二肼反应生成紫红色络合物,该络合物溶液用自制的数字图像比色装置测定颜色值实现六价铬的现场快速检测。该方法在0.05 mg/L~1.00 mg/L范围内线性良好,方法检出限为0.02 mg/L,标准溶液10次测定结果的RSD为1.6%~7.9%,实际水样加标回收率为94.7%~102%。用该方法与国标法同时测定实际水样,结果无显著差异。     

五日生化需氧量测定中稀释倍数的估算

假定样品经过培养后耗氧率达５５％；推导出ＢＯＤ５稀释倍数Ｋ＝ＢＯＤ５／４．４，由稀释程度规定推导出ＢＯＤ５稀释倍数Ｋ＝（ＢＯＤ５－１）／４．０两种方法Ｋ基本相同，标准样品，工业废水经上述方法稀释后，测定结果比较满意，尤其对工业废水测定，既缩短了分析时间，又降低了测定误差。     

分光光度法测定水中十六烷基三甲基溴化铵

基于甲基橙(MO)在水体中和阳离子表面活性剂发生的褪色反应,采用分光光度法测定十六烷基三甲基溴化铵(CTAB),优化了试验条件,讨论了干扰物质的影响。MO与CTAB在10%乙醇-水溶液中反应形成淡黄色离子缔合物,以MO的最大吸收波长470 nm为测定波长,CTAB质量浓度在0 mg/L～13.1 mg/L范围内遵守朗伯-比尔定律,吸光系数为17.48 L/(g.cm),方法检出限为0.364 mg/L,标准溶液平行测定的RSD为2.3%,样品加标回收率为91.8%～107%。     

Mapping giant salvinia with satellite imagery and image analysis

QuickBird multispectral satellite imagery was evaluated for distinguishing giant salvinia (Salvinia molesta Mitchell) in a large reservoir in east Texas. The imagery had four bands (blue, green, red, and near-infrared) and contained 11-bit data. Color-infrared (green, red, and near-infrared bands), normal color (blue, green and red bands), and four-band composite (blue, green, red, and near-infrared bands) images were studied. Unsupervised image analysis was used to classify the imagery. Accuracy assessments performed on the classification maps of the three composite images had producer’s and user’s accuracies for giant salvinia ranging from 87.8 to 93.5%. Color-infrared, normal color, and four-band satellite imagery were excellent for distinguishing giant salvinia in a complex field habitat.     

Adsorption of Cotton Fabric Dyestuff Waste Water on Nigeria Agricultural Semi-Activated Carbon

The Kaduna river in Nigeria is in such great environmental stress that the self-purifying capacity of the river has been exceeded as a result of industrial discharges. The river water is blue-green and pollution build-up is evident on the river banks. Techniques were designed to rid the river of visible signs of pollution by incorporating the principles of adsorption and incineration.Semi-activated carbon from agricultural wastes were used to treat the waste water. Residual colors, amber, yellow and orange, were obtained and the solute removed ranged from 96-99.8% and the volatile residue removed by carbon treatment ranged from 3-3.8%. Incineration of 1 kg waste water yielded 40 g solid residue.Adsorption of dyestuff present in the waste water was linear and increased with concentrations of waste water per unit mass of guinea corn carbon. Replicate results yielded: y = 2.5 + 0.130x y = 2.306 + 0.017x where x =log10% concentration of dyestuff waste water (independent variable); y = log10 adsorption of dyestuff waste-weight gramme-1 carbon. Unit of weight = milligramme (dependent variable).For maize carbon, adsorption was linear but decreased with increasing concentrations. Replicate results were: y = 1.583 - 0.21x y = 0.52 - 0.32x x and y here are the same as above; with cane sugar carbon, adsorption was independent of concentrations. Student t-test showed no statistical difference between the replicates at the 99.5% level.     

水中色度测定的研究

针对目视比色法色度测定不足之处,利用分光光度法进行改进.(1)在天然水的测定中,研究了以往的380nm作最大吸收波长测吸光度方法的问题.寻找到最佳波长455nm,吸收池5cm测定天然水吸光度A.(2)在5～400℃测定温度对吸光度无影响,溶液浊度、pH值对吸光度测定的影响呈线性关系.(3)在工业废水的测定中,先扫描出其最大吸收波长,以仪器检测限吸光度0.010为稀释终点.改进废水稀释倍数法.     

采用商业混合菌种测定BOD5的可行性

通过实验,对比研究了采用商业混合菌种（Polyseed）改进传统方法测定BOD5的可行性。研究结果表明,相比于采用地表水作为接种水的传统方法,采用进口商业混合菌种配制接种稀释水BOD5（空白值）更稳定,可以改进传统BOD5测定方法,使得日常监测工作更为便捷。     

废水的BOD_5测定中根据BOD_5／COD_（cr）值确定稀释比的一种方法

废水的ＢＯＤ５测定中取稀释比是一个很重要的问题。本文根据数学推导得出ＢＯＤ５测定中取稀释比的一种方法。ＢＯＤ５／ＣＯＤｃｒ值在０．０５－０．１，０．１－０．３，０．３－０．６，０．６－１．０四个范围内其稀释比ｆ２可对应取５５／ＣＯＤｃｒ、２２／ＣＯＤｃｒ、９／ＣＯＤｃｒ、５／ＣＯＤｃｒ。     

Analysis of river water samples utilising a prototype industrial sensing system for phosphorus based on micro-system technology

The application of a phosphorus monitoring device based on microsystems technology (MST) to the analysis of river water is presented. An alternative to the standard molybdenum blue method known as the yellow vanadomolybdophosphoric acid method has been very effectively implemented. The method is simple, a reagent and sample are mixed in a 1:1 ratio forming a yellow complex that absorbs strongly below 400 nm in the UV spectrum. The kinetics of the reaction are rapid and sample turnaround is typically 3 min at room temperature. Therefore a very uncomplicated microfluidic design can be adopted. The working wavelength was chosen as 380 nm to coincide with the peak output of a UV-LED narrow bandwidth light source recently developed by Nichia. The limit of detection for the yellow method in the microfluidic system is 0.2 ppm with a dynamic linear range from 0-50 ppm. The method was applied to a measurement of phosphorus in a local river at specific sampling points along its course.