Heavy metal concentration and speciation of seven representative municipal sludges from wastewater treatment plants in Northeast China

The analysis of heavy metals is very important for assessing the feasibility of the agricultural utilization for the municipal sludge. In this paper, a four-step sequential extraction method was applied to extract heavy metals (Cu, Zn, Mn, Cr, and Ni) in municipal sludges from seven individual wastewater treatment plants located in Jilin and Heilongjiang Province, China, for estimating the mobility and bioavailability of the metal ions in the agricultural application. The total concentrations of heavy metals and their chemical fractions after the sequential extraction were determined. Principal component analysis (PCA) was applied to analyze the relations of heavy metals fractions in the municipal sludges. Experimental results indicated that the total concentrations of Cu, Zn, Cr, and Ni in all sludge samples were below the threshold values set out by the Chinese legislation (GB18918-2002). Specially, Zn had a high bioavailability and mobility, Cu and Cr had potential bioavailability, while Mn mainly existed in the residual fraction of municipal sludge. On the other hand, Ni had different mobility in different municipal sludge. PCA results were confirmed by the environmental behavior of heavy metals.     

Spatial variation of acid-volatile sulfide and simultaneously extracted metals in Egyptian Mediterranean Sea lagoon sediments

In risk assessment of aquatic sediments, the immobilizing effect of acid-volatile sulfide (AVS) on trace metals is a principal control on availability and associated toxicity of metals to aquatic biota, which reduces metal bioavailability and toxicity by binding and immobilizing metals as insoluble sulfides. Spatial variation pattern of AVS, simultaneously extracted metals (SEM), and sediment characteristics were studied for the first time in surface sediment samples (0–20 cm) from 43 locations in Egyptian northern delta lagoons (Manzalah, Burullus, and Maryut) as predictors of the bioavailability of some divalent metals (Cu, Zn, Cd, Pb, and Ni) in sediments as well as indicators of metal toxicity in anaerobic sediments. The results indicated that the ∑SEM (Cu?+?Zn?+?Cd?+?Pb?+?Ni) values in sediments of lagoon Burullus had higher concentrations than those of Maryut and Manzalah. In contrast, AVS concentrations were considerably higher in lagoons Manzalah and Maryut and seemed to be consistent with the increase in organic matter than lagoon Burullus. Generally, the average concentrations of the SEM in all lagoons were in the order of Zn?>?Cu?>?Ni?>?Pb?>?Cd. The ratios of ∑SEM/AVS were less than 1 at all the sampling stations except at one station in lagoon Maryut as well as four stations located in lagoon Burullus (∑SEM/AVS?>?1), which suggests that the metals have toxicity potential in these sediments. Therefore, SEM concentrations probably are better indicators of the metal bioavailability in sediments than the conventional total metal concentrations.     

Levels and speciation of heavy metals in soils of industrial Southern Nigeria

A knowledge of the total content of trace metals is not enoughto fully assess the environmental impact of polluted soils. Forthis reason, the determination of metal species in solution isimportant to evaluate their behaviour in the environment andtheir mobilization capacity. Sequential extraction procedure wasused to speciate five heavy metals (Cd, Pb, Cu, Ni and Zn) fromfour contaminated soils of Southern Nigeria into sixoperationally defined geochemical species: water soluble,enchangeable, carbonates, Fe-Mn oxide, organic and residual.Metal recoveries were within ± 10% of the independentlydetermined total Cd, Pb, Cu, Ni and Zn concentrations. The highest amount of Cd (avg. 30%) in the nonresidual fractionswas found in the exchangeable fraction, while Cu and Zn weresignificantly associated with the organic fraction. Thecarbonate fraction contained on average 14, 18.6, 12.6, 13 and11% and the residual fraction contained on average 47, 18, 33,50 and 25% of Cd, Pb, Cu, Ni and Zn respectively. Assuming thatmobility and bioavailability of these metals are related to thesolubility of the geochemical form of the metals, and that theydecrease in the order of extraction sequence, the apparentmobility and potential bioavailability for these five metals inthe soil were: Pb > Zn > Cu > Ni > Cd. The mobility indexes ofcopper and nickel correlated positively and significantly withthe total content of metals, while mobility indexes of cadmiumand zinc correlated negatively and significantly with the totalcontent of metals.     

Distribution and Fractionation of Heavy Metals in Solid Waste from Selected Sites in the Industrial Belt of Delhi, India

Solid waste samples were collected from five small-scale industrial sites in the National Capital Territory (NCT) of Delhi. These industrial sites represent the regional spread of the industrial belt in the NCT of Delhi. Solid waste samples were digested using aqua-regia and HF in air tight teflon bombs for the quantitative analysis of heavy metals (Hg, Pb, Cd, Mn, Fe, Ni, Cu and Zn) by GBC model 902 atomic absorption spectrophotometer. Hg was analysed using hydrid generator attachment. Beside this sequential extraction was used to fractionate five heavy metals (Pb, Ni, Cd, Cu and Zn) into six operationally defined phases, viz. water soluble, exchangeable, carbonate-bound, Fe-Mn oxides, organic-bound and residual fractions to ascertain the relative mobility of these metals. The result obtained showed metal concentration to be in the range of Hg 0.42-2.3; Pb 23-530; Cd 014-224; Mn 494-19 964; Fe 35 684-233 119; Ni 192-1534; Cu 3065-10 144 and Zn 116-23 321 (all units in mg kg(-1)) in all the industrial areas studied. The fractionated toxic metals like Pb, Ni and Cd were observed to be in the range of 25-35, 15-50 and 40-50%, respectively, in mobile or bio-available fractions of solid waste. As this waste is often disposed-off by the roadsides, low lying areas, abandoned quarries or in landfill sites which are often not properly planned, thus posing potential risk to ground and surface water quality to millions of people living downstream.     

Speciation and ecological risk of heavy metals in intertidal sediments of Quanzhou Bay, China

The chemical speciation of nine heavy metals in intertidal sediments from Quanzhou Bay was determined using a modified sequential extraction procedure, proposed by the Commission of the European Community Bureau of Reference. The results show that Mn presents the highest percentage in the acid-soluble fraction, and Pb and Cu present the highest percentages in the reducible fraction. The highest percentages of Fe, V, Cr, Ni, Zn, and Co were found in the residual fraction. The mobility order of the heavy metals studied on the basis of the nonresidual content of the elements is Mn > Pb > Cu > Co > Zn > Ni > Cr > V > Fe. The assessment on potential ecological risk indices of some heavy metals indicates that Zn, Ni, and Cr show moderate contamination, while Cu and Pb show slighter contamination. On the whole, the comprehensive potential ecological risk index of Cu, Zn, Ni, Cr, and Pb in the sediments presents moderate degree.     

Total concentrations, fractionation and mobility of heavy metals in soils of urban area of Guwahati, India

This work describes the results of assessment of the heavy metals, Cd, Co, Cr, Cu, Mn, Ni, Pb, and Zn in urban soil of Guwahati City, India from 31 sites of five different land use types covering residential, commercial, industrial, public utilities, and roadside. Sequential extraction procedure was used to evaluate the relative distribution of the eight metals in exchangeable, carbonate, reducible (Fe?CMn oxide), organic and sulfide, and residual fractions. Of the eight metals, Cd and Co occur in lower concentrations (Cd <?< Co) in all types of land, and concentration variation from one type of land use to another is not much significant for both the metals. Ni presence is more than Co, and the concentrations show some variation depending on land use status. Average Cr and Cu concentrations are ??100?mg/kg, but Cr has a significantly higher presence in industrial land use. The results are similar in case of Pb. The two metals, Mn and Zn have domination over the other metals, and the values are ??300?mg/kg. Industrial and roadside soil contains much more Mn, while commercial soil is most enriched with Zn. Of the metals, Ni has the largest proportion (~42%) bound to the exchangeable fraction and Co, Cr, and Pb also have appreciable proportion bound to the same fraction. A significant amount of Co is associated with carbonates. The reducible fraction has bound considerable quantity of Mn and Zn, while most of Cu is associated with the organic and sulfide fraction. Both Cd and Pb are dominantly associated with the residual fraction. Computation of the mobility factor of the metals indicates Mn to be the most mobile metal present in the soil samples.     

长江下游沉积物中重金属污染现状与特征

对长江下游沉积物中的重金属Co、Cr、Cu、Ni、Pb、Zn、Mn、Hg和As进行全量和醋酸提取态(包括水溶态、可交换态和碳酸盐结合态)分析.结果表明,大部分重金属主要来源于地壳元素的自然释放,但Cu、Zn、Hg和As在最近十几年因受到人为排放的影响质量比有所增加.长江江苏段的重金属质量比普遍高于入海口上海段;位于悬浮物易沉降地区的靖江重金属质量比明显偏高.Cu和Zn总体质量比较高,且醋酸提取态所占比例较大,对长江下游存在潜在的生态风险.     

Pollution in the urban soils of Lianyungang,China, evaluated using a pollution index,mobility of heavy metals,and enzymatic activities

Soil samples from 16 urban sites in Lianyungang, China were collected and analyzed. A pollution index was used to assess the potential ecological risk of heavy metals and a sequential extraction procedure was used to evaluate the relative distribution of Cu, Zn, Pb, Cd, Cr, and As in exchangeable, carbonate, Fe/Mn oxide, organic/sulfide, and residual fractions. The mobility of heavy metals and urease (URE) activity, alkaline phosphatase (ALP) activity, and invertase (INV) activity of soils was determined. The results showed that the average concentrations of Cu, Zn, Pb, Cd, Cr, and As in Lianyungang soils were much higher than those in the coastal city soil background values of Jiangsu and China. Among the five studied regions (utilities, commercial, industrial, tourism, and roadside), the industrial region had the highest metal concentrations demonstrating that land use had a significant impact on the accumulation of heavy metals in Lianyungang soils. Compared to the other metals, Cd showed the highest ecological risk. According to chemical partitioning, Cu was associated with the organic/sulfides and Pb and Zn were mainly in the carbonate and the Fe/Mn oxide phase. The greatest amounts of Cd were found in exchangeable and carbonate fractions, while Cr and As were mainly in the residual fraction. Cd had the highest mobility of all metals, and the order of mobility (highest to lowest) of heavy metals in Lianyungang soils was Cd > Zn > Pb > Cu > As > Cr. Soil urease activity, alkaline phosphatase activity, and invertase activity varied considerably in different pollution degree sites. Soil enzyme activities had the lowest levels in roadside and industrial regions. Across all the soil data in the five regions, the total Cu, Zn, Pb, Cd, Cr, and As level was negatively correlated with urease activity, alkaline phosphatase activity, and invertase activity, but the relationship was not significant. In the industrial region, alkaline phosphatase activity had significant negative correlations with total Cu, Pb, Cr, Zn, Cd, and heavy metal fractions. This showed that alkaline phosphatase activity was sensitive to heavy metals in heavily contaminated regions, whereas urease and invertase were less affected. The combination of the various methods may offer a powerful analytical technique in the study of heavy metal pollution in street soil.     

Distribution and speciation of selected metals in surface sediments, from the tropical Zuari estuary, central west coast of India

Estuarine sediments are major reservoirs for the metals. Distribution and mobility of metals within estuaries depends strongly on their specific chemical form. In the present study, surface sediments from Zuari estuary, Goa were analysed by a sequential procedure for Fe, Mn, Cu, Zn, Cr and Co to determine their distribution in five geochemical phases (Exchangeable, carbonate, Fe-Mn oxide (reducible) organic bound (oxidisable) and residual). The total metal content, sand, silt, clay and organic carbon were also determined of the surface sediments. The total metal contents were found to be greater than the background concentrations of average shale values as well as to that of earlier studies indicating enrichment probably due to the anthropogenic origin of metals. The results obtained from sequential procedure showed that among the studied elements, Mn and Co are potentially available in the bioavailable fractions (exchangeable, carbonate and Fe-Mn oxide bound fractions) indicating their importance in toxicity whereas rest of the metals viz. Fe, Cu, Zn and to some extent Cr are largely available in residual phase although they are available in other fractions. The main source of metals to the estuary is mining and its associated activities in the study area. Chemical speciation by sequential extraction procedure has helped in assessing the mobility, bioavailability, diagenesis and toxicity of metals and hence giving a better insight into the ultimate fate of pollutants, which are introduced into the estuarine environment. To understand the risk of the metals to the sediment dwelling organisms the data were compared with the Sediment Quality Values (SQV) using SQUIRT. Also, correlation and Factor analysis were carried out to understand the associations of metals in the different fractions with sand, silt, clay, organic carbon and with other metals.     

Mobility and ecological risk assessment of trace metals in polluted estuarine sediments using a sequential extraction scheme

The three-stage sequential extraction procedure for the fractionation of Cd, Cr, Cu, Ni, Pb, and Zn, proposed by the Commission of the European Communities Bureau of Reference, was applied to sediment five samples collected from the Sal estuary, Sergipe State, northeast Brazil, in September 2009. The method showed satisfactory recoveries, detection limits, and standard deviations for determinations of trace metals in the sediments. Cd and Pb were the metals most prevalent in the bioavailable fractions (carbonates, Fe and Mn oxides, organic matter, and sulfides), while Ni, Zn, Cu, and Cr showed higher percentages in the inert fraction. The order of mobility of the metals was Cd (66 %) > Pb (65 %) > Zn (59 %) > Ni (57 %) = Cr (57 %) > Cu (56 %). Possible toxicity related to these metals was examined using the risk assessment code, and by comparing the chemical data with sediment quality guideline ERL-ERM values. Results obtained using the two methods were in agreement, and showed low to medium risk for all metals, indicating that adverse effects on aquatic biota should rarely occur.     

Heavy metal binding fractions in the sediments of the Godavari estuary,East Coast of India

Sequential chemical extraction was used to study the operationally determined chemical forms of five heavy metals (Pb, Cu, Zn, Co and Ni) and their spatial distribution in the sediments. The binding behaviour of heavy metals associating with Fe–Mn oxides showed a good correlation towards Cu, Zn and Co, but moderate linear dependence with Ni and Pb. Among the five metals, correlation between Fe–Mn oxide bound Cu and Fe–Mn oxides (r = 0.95) is highest. The coefficient of determination (r ²) in organically bound heavy metals versus organic matter (OM) ranges from 0.772 to 0.952, which indicates a good linear dependence. The OM fraction in the sediments is more accessible to heavy metals and is the major ligand available for complexation. In particular, Zn and Cu are preferentially bound to OM. In general, Zn co-precipitation with carbonates is the dominant chemical form when Fe–Mn oxide and OM are less abundant. In this study, however, carbonates were less abundant, hence Zn bound to carbonates was less pronounced. Based on the results, even if the excessive binding sites are contained in the sediments, competition of various complexation reactions between sediment phases and heavy metals could dominate metal association.     

Spatial distribution and potential ecologic risk assessment of heavy metals in the sediments of the Nansi Lake in China

The contamination levels and ecological risks of heavy metals in the sediments of the Nansi Lake were investigated. The contents of Cd, Cr, Cu, Pb, Zn, Ni, and Co in the surface sediments collected at 20 sites ranged from 0.08 to 1.12, 58.92 to 135.62, 38.09 to 78.65, 24.51 to 53.95, 110.51 to 235.36, 11.30 to 65.40, and 4.12 to 20.14 mg/kg, respectively. The results of partitioning analysis revealed that the proportions of soluble and exchangeable fraction were less than 1 %, the proportions of carbonate, amorphous oxides, organic matter, and crystalline oxides fraction were less than 10 %, and 10.52 % of Cd was associated with carbonate. The average proportions in the residual fraction ranged from 48.62 % for Cu to 73.76 % for Ni, indicating low mobility and bioavailability. The geoaccumulation index (I _geo), relative enrichment factor (REF), sediment pollution index (SPI), and potential effect concentration quotient (PECQ) values of the heavy metals in the sediments were not in agreement with each another. The average REF values of Cd and Zn were higher than those of other metals. However, the average PECQ values were higher for Cr and Ni than those of other metals, indicating that these two metals would cause higher adverse biological effects. Therefore, it is suggested that future management and pollution control might focus on Cd, Zn, Cr, and Ni in the sediments of the Nansi Lake.     

Chemical fractionation of heavy metals in urban soils of Guangzhou, China

Knowledge of the total concentration of heavy metals is not enough to fully assess the environmental impact of urban soils. For this reason, the determination of metal speciation is important to evaluate their environment and the mobilization capacity. Sequential extraction technique proposed by the former European Community Bureau of Reference (BCR) was used to speciate Cd, Cu, Fe, Mn, Ni, Pb, and Zn in urban soils from Guangzhou into four operationally defined fractions: HOAc extractable, reducible, oxidizable, and residual. The Cu, Fe, Ni, and Zn were predominately located in the residual fraction, Pb in the reducible fraction, and Cd and Mn within the HOAc extractable fraction. The order of Cd in each fraction was generally HOAc extractable > reducible > residual > oxidizable; Cu and Fe were residual > reducible > oxidizable > HOAc extractable; Mn was HOAc extractable > residual > reducible > oxidizable; Ni and Zn were residual > reducible > HOAc extractable > oxidizable; and Pb was reducible > residual > oxidizable > HOAc extractable. Cadmium was identified as being the most mobile of the elements, followed by Mn, Zn, Ni, Cu, Pb and Fe. Iron–Mn oxides can play an important role in binding Cd, Cu, Ni, Pb, and Zn and in decreasing their proportion associated with the residual fraction in the soils. With total concentrations of Cd, Cu, Ni, Pb, Zn, and Mn increase, these metals more easily release and may produce more negative effects on the urban environment.     

Monitoring of total and bioavailable heavy metals concentration in agricultural soils

The aim of this paper is to evaluate total and bioavailable concentration of heavy metals in agricultural soils in order to estimate their distribution, to identify the possible correlations among toxic elements and the pollution sources, to distinguish the samples in relation to sampling site or to sampling depth, and to evaluate the available fraction providing information about the risky for plants. In particular, we reinvestigated total concentrations of As, Be, Cd, Cr, Cu, Fe, Hg, Mn, Ni, Pb, Sb, V, and Zn and available concentrations of As, Be, Cd, Cr, Cu, Hg, Ni, Pb, Sb, and Zn in soil from Apulia (Southern Italy). Analytical results showed that total concentrations, for all soils, are in the range permitted by regulations in force in Italy, but some soils evidence slight enrichment of Cd, Cr, Cu, Pb, and Zn. All the heavy metals in the available fraction were below the detection limits of the analytical techniques used except Cu, Ni, Pb, and Zn.     

养猪粪污厌氧消化重金属变化特征及影响

对太湖流域某典型养猪区域粪污收集后集中厌氧消化处理,分析猪饲料、猪粪和沼肥中重金属总量和形态变化特征,探讨厌氧消化过程重金属形态变化及其影响因素。结果表明,不同养殖阶段中猪饲料重金属含量差异较大,仔猪饲料和猪粪中Cu、Zn和Cd含量较高,而Cr和Ni在生长肥育猪后期饲料和猪粪中含量最高。猪粪中Cu主要以有机结合态、Zn主要以Fe-Mn氧化物结合态、Pb和Cr主要以残渣态、Ni主要以Fe-Mn氧化物态和碳酸盐结合态赋存,沼液中Cu和Zn平均值为猪粪液中含量的1. 59和1. 40倍,沼渣中Cu和Zn平均值为调节池猪粪的1. 58和1. 37倍,厌氧消化后重金属存在"相对浓缩效应",pH值、DOC和OM为厌氧消化过程影响重金属变化的主要因素。     

Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

Speciative distribution and bioavailability of metals in agricultural soils receiving industrial wastewater

In order to assess the metal pollution status of agricultural lands of Mandi Bahauuddin receiving industrial wastewater, 35 top soil samples were investigated for the determination of selected metal levels, i.e., Fe, Cu, Cd, Cr, Ca, Ni, and Pb by flame atomic absorption spectroscopy under optimum analytical conditions. The distribution of these metals in different operationally defined chemical fractions was also determined by using the sequential extraction technique. The highest mean total concentration was found for Fe while the least one was observed for Pb. All the studied metals were found to be present at levels much enhanced than national and international standards. Moreover, most of the metals were distributed principally in residual fraction with the exception of Ni which was found to be associated mainly with oxidizable fraction. The significant correlations were observed between Fe-Mn oxide-bound and residual fractions and exchangeable and oxidizable fractions for most of the metals. The highest mobility was exhibited by Ni that evidenced its enhanced bioavailability in the soil. The multivariate statistical analyses in terms of principal component analysis (PCA) and cluster analysis (CA) revealed multiple sources for various geochemical fractions of different metals. CA also revealed that the nonresidual fractions of most of the metals were very closely associated while PCA presented a distinctive behavior of Ca in the soil. It was therefore suggested that in order to avoid the metal contamination arising from industrial wastewater, appropriate remediation strategies must be adopted.     

Distribution and solid-phase speciation of toxic heavy metals of bed sediments of Bharali tributary of Brahmaputra River

Heavy metal (Fe, Mn, Zn, Cu, Ni, Pb, and Cd) concentrations and their chemical speciations were investigated for the first time in bed sediments of Bharali River, a major tributary of the Brahmaputra River of the Eastern Himalayas. Levels of Fe, Mn, Pb, and Cd in the bed sediments were much below the average Indian rivers; however, Cu and Zn exhibit levels on the higher side. Enrichment factors (EF) of all metals was greater than 1 and a higher trend of EF was seen in the abandoned channel for most metals. Pb showed maximum EF of 32 at site near an urban center. The geoaccumulation indices indicate that Bharali river is moderately polluted. The metals speciations, done by a sequential extraction regime, show that Cd, Cu, and Pb exhibit considerable presence in the exchangeable and carbonate fraction, thereby showing higher mobility and bioavailability. On the other hand, Ni, Mn, and Fe exhibit greater presence in the residual fraction and Zn was dominant in the Fe?CMn oxide phase. Inter-species correlations at three sites did not show similar trends for metal pairs indicating potential variations in the contributing sources.     

Heavy Metals Monitoring using Bivalves from Mediterranean Sea and Red Sea

The concentrations of heavy metals (Cd, Co, Cu, Fe, Mn, Ni, Pd and Zn) were measured in the Bivalves (Modiolus auriculatus and Donax trunculus) collected from the Egyptian coasts of Mediterranean Sea and Brachiodonates sp. from the Egyptian coasts of Red Sea. The average concentrations of the heavy metals analyzed exhibited the following decreasing order: Fe > Zn > Cu > Mn > Ni > Co > Pb > Cd for both Mediterranean Sea and Red Sea. The analyses of Cd, Co, Ni, Pb, and Zn showed higher average concentrations for samples collected from Red Sea than that collected from Mediterranean Sea, while Fe, Cu and Mn showed the reverse results. Fe was used as a normalizing agent for all studied metals and exhibited presence of two locations from each of Mediterranean Sea and Red Sea have anthropogenic inputs of heavy metals. These results suggest that the coastal area in both Mediterranean Sea and Red Sea of Egypt might be considered relatively unpolluted with heavy metal.     

Assessment of heavy metals in sediments from a typical catchment of the Yangtze River, China

An intensive investigation was conducted to study the accumulation, speciation, and distribution of various heavy metals (As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn) in sediments from the Yangtze River catchment of Wuhan, China. The potential ecological risks posed by these heavy metals also were estimated. The median concentrations of most heavy metals (As, Cd, Cr, Cu, Ni, Pb, and Zn) were higher than the background values of soils in Wuhan and were beyond the threshold effect level (TEL), implying heavy metal contamination of the sediments. Carbonate-bound Cd and exchangeable Cd, both of which had high bioavailability, were 40.2% and 30.5% of the total for Cd, respectively, demonstrating that Cd poses a high ecological risk in the sediments. The coefficients of the relationship among Pb, Hg, and Cu were greater than 0.797 using correlation analysis, indicating the highly positive correlation among these three elements. Besides, total organic carbon content played an important role in determining the behaviors of heavy metals in sediments. Principal component analysis was used to study the distribution and potential origin of heavy metals. The result suggested three principal components controlling their variability in sediments, which accounted for 36.72% (factor 1: Hg, Cu, and Pb), 28.69% (factor 2: Cr, Zn, and Ni), and 19.45% (factor 3: As and Cd) of the total variance. Overall, 75% of the studied sediment samples afforded relatively low potential ecological risk despite the fact that generally higher concentrations of heavy metals relative to TEL were detected in the sediments.