Evaluation of Abelmoschus esculentus (lady's finger) seed as a novel biosorbent for the removal of Acid Blue 113 dye from aqueous solutions

The use of a new biosorbent derived from Abelmoschus esculentus (A. esculentus) seed for the removal of Acid Blue 113 (AB113) in aqueous solutions was investigated in batch mode. Biosorption studies were carried out under varying operational parameters including initial pH, biosorbent dosage, contact time, initial dye concentration and temperature. The results indicated that the biosorption properties were strongly dependent on initial pH. Fourier transform infrared spectroscopy analysis revealed that hydroxyl, carboxylic and amide functional groups present on the biosorbent surface were involved in the dye removal process. Equilibrium data were best fitted by the Langmuir model. The maximum biosorption capacity was 169.9 ± 3.1 mg g⁻¹ at 25 °C and initial pH 5.5. The kinetic data were in good agreement with the pseudo-second-order kinetic model. The process was controlled by diffusion through boundary layer at the initial stage followed by intra-particle diffusion at the later stage. Thermodynamic evaluation showed that the process was endothermic and spontaneous. The present study suggests that A. esculentus seed with maximum biosorption capacity which compared well with values reported in the literature can be a potential biosorbent for AB113 dye removal.     

Investigation on removal of p-nitrophenol using a hybridized photo-thermal activated persulfate process: Central composite design modeling

The aim of this work is the study of p-nitrophenol (PNP) removal, as a nitroaromatic compound, using a hybridized photo-thermally activated potassium persulfate (KPS) in a fully recycled batch reactor. Response surface method was used for modeling the process. Reaction temperature, KPS initial dosage and initial pH of the solution were selected as variables, besides PNP degradation efficiency was selected as the response. ANOVA analysis reveals that a second order polynomial model with F-value of 41.7, p-value of 0.0001 and regression coefficient of 0.95 is able to predict the response. Based on the model, the process optimum conditions were introduced as initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 66 °C. Also experiments showed that using thermolysis and photolysis of the persulfate simultaneously, the role of thermolysis is not considerable. A pseudo first order kinetic model was established to describe the degradation reaction. Operational cost, as a vital industrial criterion, was estimated so that the condition of initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 25 °C showed the highest cost effective case. Under the preferred mild condition, the process will reach to 84% and 89% of degradation and mineralization efficiencies, after 60 and 120 min, respectively.     

Kinetic analysis of transesterification of waste pig fat in supercritical alcohols

The kinetic analysis method using non-isothermal technique was proposed to determine the kinetic parameters for the transesterification reaction of waste pig fat in supercritical alcohols. To investigate the transesterification of waste pig fat, the waste pig fat to alcohol ratio (w/w) was varied from 1:1.5 to 1:2.5 between the temperatures 220 and 290 °C at an interval of 10 °C in a 25 mL batch reactor. The products were analyzed by gas chromatography mass spectrometry. To verify the effectiveness of the proposed kinetic analysis method, the experimental values were compared with the values calculated using the kinetic parameters obtained from this work. It was found that the proposed kinetic analysis method gave reliable kinetic parameters for the transesterification of waste pig fat in supercritical alcohols. Further, it was found that the apparent activation energy for supercritical ethanol was lower than the value for supercritical methanol.     

Pb(II) adsorption from aqueous solutions by raw and treated biomass of maize stover – A comparative study

The potential to remove Pb(II) ion from wastewater treatment systems using raw and treated maize stover through adsorption was investigated in batch experiments. To achieve this, batch mode experiments were conducted choosing specific parameters such as pH (2–8), dosage concentration (2–30 g L⁻¹), contact time (5–180 min), temperature (20–45 °C) and metal ion concentrations (10–50 mg L⁻¹). Adsorption was pH-dependent showing a maximum at pH value 5. The equilibrium sorption capacities of raw and treated maize stover were 19.65 and 27.10 mg g⁻¹, respectively. The adsorption data fitted well to the Langmuir isotherm model. Kinetic studies revealed that the adsorption process followed pseudo-second-order model. The calculated thermodynamic parameters showed that the adsorption of Pb(II) was spontaneous and exothermic in nature. Consequently, this study demonstrated that both raw and treated maize stover could be used as adsorbents for the treatment of Pb(II) from industrial wastewaters.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Improving disintegration and acidification of waste activated sludge by combined alkaline and microwave pretreatment

The individual alkaline or microwave pretreatment has been proved to be effective in disintegration and acidification of waste activated sludge (WAS). In this study, the effects of combined alkaline and microwave pretreatment at different pH and specific energy input (Es) on WAS disintegration were investigated using response surface methodology (RSM). Combined pretreatment achieved disintegration degree (DD) of 65.87% at Es of 38,400 kJ/kg TS and pH 11.0. The ANOVA further demonstrated that pH showed more significant effect on DD than Es. Anaerobic batch experiment results showed that combined pretreatment not only significantly improved volatile fatty acids (VFAs) accumulation but also shortened the time for the highest VFAs accumulation. The maximal VFAs accumulation (1500 mg COD/L) obtained at Es of 28,800 kJ/kg TS and fermentation time of 72 h, which was about two times that of the treatment without microwave (850 mg COD/L) at 96 h. The analysis of VFAs composition showed that the VFAs mainly consisted of acetic and iso-valeric acids, accounting for 57.3–70.1% of total VFAs.     

Thermal characterization of fly ash from one municipal solid waste incinerator (MSWI) in Shanghai

This study aims to develop a methodology for the thermal characterization of MSWI fly ash. We performed TGA–DTA and component variation analysis, microstructure transfer of sintered fly ash, as well as leaching toxicity, volatilization ratio and specification transformation of heavy metals as a function of temperature. It is found that content of crystal phases first increases between room temperature and 800 °C and then decreases between 800 °C and 1200 °C, while that of glass phases registers a reverse trend. Fly ash registers a SiO₂–Al₂O₃–metal oxides system and its content of glass phases is around 57%. Increase of sintering temperature between 600 °C and 1200 °C is conducive to the reduction of soluble As, Cd, Cu, Hg, Pb, Ni and Zn, while content of soluble Cr increases as temperature rises from 800 °C to 1200 °C.     

Synthesis of CuO nanoparticles through green route using Citrus limon juice and its application as nanosorbent for Cr(VI) remediation: Process optimization with RSM and ANN-GA based model

In present investigation, an attempt has been made for the synthesis of cupric oxide nanoparticles (CuONPs) through a green route by utilizing lemon juice extract as a bioreductant. The synthesized CuONPs were characterized through UV–visible spectroscopy, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The CuONPs were utilized for Cr(VI) removal from water through adsorption method in batch mode at different initial Cr(VI) concentration, pH, temperature and CuONPs dosage. The maximum uptake capacity of CuONPs was found to be 16.63 mg of Cr(VI)/g at pH 4.0. Implementation of response surface methodology (RSM) followed by artificial neural network hybridized with genetic algorithm (ANN-GA) approach has resulted maximum Cr(VI) adsorption of 98.8% under the optimized conditions of initial metal concentration 22.5 mg/L, pH 3.81, CuONPs dose 1.28 g/L and temperature 37.1 °C. Under optimum conditions, adsorption isotherm study was conducted, which showed that the fitness of experimental data was well achieved with Langmuir isotherm model illustrating monolayer pattern of adsorption. Thermodynamic study revealed that the process was spontaneous and endothermic in nature, while adsorption kinetics was best explained by pseudo-second order kinetic model.     

Autoignition temperature data and scaling for amide solvents

Autoignition temperature tests using the ASTM E659 test method have been conducted for N,N-dimethylacetamide (DMAC) and N,N-dimethylformamide (DMF) in test vessels with volumes of 0.5 l, 5 l, and 12 l. Tests were conducted at three different laboratories yielded good agreement (standard deviation with 5 °C) in all cases except for DMAC in the 0.5 l test vessel (standard deviation of 23 °C). Scaling correlations have been developed for the decrease of autoignition temperature with increasing volume and for increasing values of the vessel volume to surface area ratio. The variations for DMAC are steeper than the literature values for almost all other combustible liquids. Cool flames were observed for DMAC at temperatures as much as 44 °C below the autoignition temperature and for DMF at temperatures as much as 171 °C below its autoignition temperature. The DMF cool flame temperatures in the 5-l and 12-l test vessels are approximately equal to the DMF autoignition temperature in a closed 12-l test vessel. Gas samples taken after the cool flame and hot flame tests reveal the presence of high concentrations of diamines and dimethylamino acetonitrile, and small concentrations of many other partial decomposition/oxidation components.     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

Evaluating the efficacy of alumina/carbon nanotube hybrid adsorbents in removing Azo Reactive Red 198 and Blue 19 dyes from aqueous solutions

Concerning the high volume of wastewater containing dye in Iran and its adverse effects, it is necessary to develop scientific solutions for treating these wastewaters. The aim of this study was to evaluate the efficiency of the alumina-coated multi-walled carbon nanotubes in removing the Reactive Red 198 (RR 198) and Blue 19 (RB 19) dyes. Synthetic samples including dye with different concentrations were prepared. These samples were put in contact with different contents of alumina/multi-walled carbon nanotubes, in different pH values, in different contact times, different temperatures and the presence of sodium sulfate or sodium carbonate. The optimum pH, dye concentration and temperature for removal of the two dyes was 3, 50 mg l⁻¹ and 25 °C, respectively. The optimum adsorbent dose for removal the RR 198 dye was 0.5 g l⁻¹ and for Blue 19 was 0.4 g l⁻¹. The optimum contact time for RR 198 was 150 min and RB 19 was 180 min. In this condition, maximum removal efficiency for RR 198 and RB 19 was 91.54% and 93.51%, respectively. The adsorption study was analyzed kinetically, and the results revealed that the adsorption fitted a pseudo-second order kinetic model. According to these results alumina/multi-walled carbon nanotubes can effectively remove RR 198 and RB 19 from aqueous solutions.     

Degradation of Rhodamine B by an electrochemical ozone generating system consist of a Ti anode coated with nanocomposite of Sn–Sb–Ni oxide

An ozonation process was performed using a recycled electrochemical ozone generator system. A titanium based electrode, coated with nanocomposite of Sn–Sb–Ni was applied as anode in a laboratory-made electrochemical reactor. A constant flow rate of 192 mg/h of generated ozone was entered to an ozonation reactor to contact with a typical target pollutant, i.e., Rhodamine B (Rh.B) molecules in aqueous solution. Four operational parameters such as: initial dye concentration, pH, temperature and the contact time were evaluated for the ozonation process. Experimental findings revealed that for a solution of 8 mg/L of the dye, the degradation efficiency could reach to 99.5% after 30 min at pH 3.7 and temperature of 45 °C as the optimum conditions. Kinetic studies showed that a second order equation can describe the ozonation adequately well under different temperatures. Also, considering to the importance of process simulation, a three-layered feed forward back propagation artificial neural network model was developed. Sensitivity analysis indicated order of the operational parameter's relative importance on the model output as: time ≫ pH > Rh . B initial concentration > temperature.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Sensitivity analysis and optimization for gasoline vapor condensation recovery

Volatile organic compounds (VOCs) are easily evaporated and discharged from everywhere into the atmosphere, especially in various operations of gasoline. The emission of VOCs is always a significant environmental problem, and the control of VOCs pollution has been a hot topic in the field of air purification. In this paper, the condensation separation method for gasoline vapor recovery was investigated and four gasoline vapors of S1–S4 were selected for the sensitivity analysis and optimization of the condensation process, using the Model Analysis Tools from Aspen Plus. Generally, to control VOCs pollution efficiently, both the vapor recovery efficiency and the outlet vapor concentration of the condensation recovery system should be simultaneously considered. Then an optimized three-stage condensation process was proposed, whose condensation temperatures were optimized and designed at 1 °C, −40 °C and −110 °C, respectively. Further, based on the comprehensive consideration of both meeting the more strict VOCs emission standard and ensuring the condensation recovery system work stably and economically, it was recommended that the maximum total vapor recovery efficiencies for S1–S4 should be 99.73%, 99.79%, 99.82% and 99.19%, and the minimum outlet vapor concentrations be 2.87 g/m³, 2.75 g/m³, 3.04 g/m³ and 16.98 g/m³, respectively. Accordingly, the condensation temperature of the copious cooling stage should be set at −130 °C. Moreover, the total cooling duties for the single-stage and three-stage condensation processes were investigated and compared when the condensation temperature of the recovery system ranged from 20 °C to −110 °C. The total cooling duties of the three-stage condensation process for S1–S4 would be saved by 12.23%, 15.68%, 13.96% and 15.65%, respectively. Finally, a three-stage condensation system was developed for the industrial gasoline vapor recovery, which has performed well since its installation.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Inherently safer reactors: Improved efficiency of 3-picoline N-oxidation in the temperature range 110–125 °C

Alkylpyridine N-oxides are important intermediates in the pharmaceutical and agrochemicals industries. The N-oxides are produced via the homogeneously catalyzed oxidation of the respective alkylpyridines using a 50% excess of hydrogen peroxide. The competitive hydrogen peroxide decomposition produces oxygen in the flammable environment of alkylpyridines and thus forms a key hazard for this reaction. In this work, the N-oxidation was performed under pressure in the temperature range of 110–125 °C with different catalyst concentrations. It was shown that temperature had an undisputable positive effect on the N-oxidation efficiency. The accurate measurement of the pressure rise due to decomposition was difficult. However, only 5% of the added H₂O₂ decomposed when stoichiometric quantities were employed, even in the temperature of 110 °C. The N-oxidation was very efficient, even when the lowest concentration of catalyst employed in this study was used.     

Adsorptive removal of basic dyes from aqueous solutions by surfactant modified bentonite clay (organoclay): Kinetic and competitive adsorption isotherm

Cationic surfactant (Hexadecyltrimenthylammonium chloride) modified bentonite clay was prepared and systematically studied for its adsorption behavior as an efficient adsorbent for the removal of basic dyes such as methylene blue (MB), crystal violet (CV) and Rhodamine B (RB) from aqueous phase. Organo modified clay shows better capacity for the removal of three dyes. The adsorption process was found to be dependent on pH and initial dye concentration. The maximum dye sorption was found to be at a pH of 9.0 (99.99% for MB, 95.0% for CV and 83.0% for RB). The adsorption capacity for the dyes was found to be 399.74, 365.11 and 324.36 μmol/g for MB, CV and RB, respectively at 30 °C. The equilibrium uptake was attained within 240 min. The kinetic studies were revealed that sorption follows a pseudo-second-order kinetic model which indicates chemisorption between adsorbent and adsorbate molecules. Adsorption isotherm indicates non-energetically adsorption sites which fit with Freundlich isotherm model. The fitness of kinetics and isotherm models was evaluated by using HYBRID error analysis function. Competitive adsorptions of dyes were studied by using binary component systems.     

Disintegration of municipal waste activated sludge by simultaneous combination of acid and ultrasonic pretreatment

The individual and simultaneous effects of acid and ultrasonic pretreatment on the disintegration of municipal waste activated sludge (WAS) were investigated based on chemical properties of WAS. In the combination of acid and ultrasonic pretreatment methods (ultrasonic-acid pretreatment), lowering pH accelerated and enhanced the disintegration of waste biological sludge. Therefore, the same disintegration efficiency (obtained by ultrasonic pretreatment alone) was achieved by the combined pretreatment in shorter sonication times. Optimum pretreatment conditions were ultrasonic power density of 1.0 W/mL and pretreatment time of 10 min for ultrasonic pretreatment alone, and ultrasonic power density of 1.0 W/mL, pretreatment time of 10 min and initial sludge pH of 2.0 for the combined pretreatment. Sludge disintegration degrees were about 30% and 40% under these optimized conditions, respectively. Optimum sludge concentration was found to be 1.0% total solid (TS) content for the combined pretreatment. As a result, ultrasonic-acid pretreatment has been determined as a new and effective combined sludge pretreatment method to improve the sludge disintegration.     

Synthesis of hydroxyapatite/clay and hydroxyapatite/pumice composites for tetracycline removal from aqueous solutions

Synthesized hydroxyapatite/clay (HA-C) and hydroxyapatite/pumice (HA-P) composites were used for tetracycline (TC) uptake studies from aqueous solution and their uptake capacities were compared. HA-C and HA-P composites were synthesized by precipitation method and the structures of the synthesized composites were characterized by XRD, SEM and BET analyses. Cation exchange capacities of HA-C and HA-P were found to be 84 meq/100 g and 33 meq/100 g, respectively. The TC adsorption using HA-C and HA-P was studied on batch mode. Various parameters such as contact time, solution pH, initial TC concentration, composite dosage, salinity and temperature were optimized. Langmuir, Freundlich and Dubinin–Radushkevich (D–R) isotherm models were applied to the equilibrium data. The maximum adsorption capacity onto HA-C was found to be 76.02 mg/g and about four times larger than the adsorption capacity of the HA-P (17.87 mg/g). The results indicated that the TC uptake onto HA-C and HA-P composites is mainly by a surface complexation and ion-exchange mechanism which depend on the solution pH. The calculated values of thermodynamic parameters indicated that the TC adsorption is favorable, physicochemical in nature. The sorption process follows pseudo-second-order and intraparticle diffusion kinetic models. The TC adsorption mechanism by HA-C and HA-P has been proposed.     

7 mT static magnetic exposure enhanced synthesis of poly-3-hydroxybutyrate by activated sludge at low temperature and high acetate concentration

The effect of 7 mT (milliTesla) SMF (static magnetic field) on poly-3-hydroxybutyrate (PHB) production was studied at an acetate concentration of 260 Cmmol l^?1 and temperature of 10 °C. The SMF decreased the specific acetate uptake rate by 29%, but increased the maximum PHB content and the yield of PHB on acetate by 32 and 28% respectively. The ratio q_P/(q_S ? q_P), which described specific PHB production rate over the difference between specific acetate uptake rate and specific PHB production rate, was introduced for evaluation of the ratio of carbon flux into PHB synthesis and into the TCA (tricarboxylic acid) cycle. This value reached 2.3 when activated sludge culture was exposed to magnetic field of 7 mT, which was 1.1 times higher than the q_P/(q_S ? q_P) value obtained without magnetic exposure. Therefore, the SMF promoted diversion of more acetyl-CoA towards PHB synthesis and could offset adverse effects of high acetate concentration and low temperature. These results provide evidence that SMF enhances PHB production by activated sludge.