pH-conditioning for simultaneous removal of arsenic and iron ions from groundwater

The effects of some commonly used pH conditioners, viz., lime, banana ash, the carbonate and the bicarbonate of sodium and potassium and their binary mixture, on simultaneous removal of arsenic and iron ions from water have been studied. KHCO₃ has been found to be the most suitable pH conditioner for the purpose. About 80 mg/L KHCO₃ can remove both arsenate and iron ions from initial 250 μg/L and 20 mg/L to below their respective guideline values of the WHO for drinking water, retaining the final pH in the acceptable range for drinking. The simultaneous removal of arsenate and iron by the pH-conditioners decreases in the order: Lime > KHCO₃ > NaHCO₃ > K₂CO₃ > Na₂CO₃ > ash. However, lime requires post-treatment correction of highly alkaline pH. The arsenate ion is removed predominantly through goethite or ferrihydrite in the presence of the bicarbonates and through ferric hydroxide in the presence of the more alkaline pH-conditioners. KHCO₃ is more advantageous over the more basic substances including NaHCO₃, because with it, one not only needs the smallest dose but also can avoid careful adjustment of the dose for regulating the initial and the final pH. The paper clearly demonstrates the potential of KHCO₃ to substitute the currently used pH-conditioners, viz., ash, lime and NaHCO₃ for simultaneous removal of arsenate and iron ions.     

A novel pretreatment process of mature landfill leachate with ultrasonic activated persulfate: Optimization using integrated Taguchi method and response surface methodology

A novel advanced oxidation process (AOP) using ultrasonic activated persulfate oxidation was used to pretreat mature landfill leachate. The effects of different operating variables (e.g., the initial S₂O₈²⁻ concentration, pH, temperature, ultrasonic power and reaction time) on the oxidation performance were investigated regarding the total organic carbon (TOC) removal efficiency, and the variables were optimized using the integrated Taguchi method and response surface methodology (RSM). Based on the Taguchi method under L₁₆ (4⁵) arrays and a grey relational analysis, the most significant variables included the initial S₂O₈²⁻ concentration, temperature and reaction time. The concentrations of these variables were further optimized using RSM. Using the integrated optimization method, the optimal conditions included an initial S₂O₈²⁻ concentration of 8.5 mM, a reaction temperature of 70 °C and a reaction time of 2.46 h, which resulted in a TOC removal efficiency of 77.32%. The experimental results showed that the enhanced TOC removal from mature landfill leachate by sono-activated persulfate oxidation could be attributed to the combined effects of ultrasonic catalysis and sulfate radical-AOP. Overall, ultrasonic activated persulfate oxidation is a promising method for the pretreatment of landfill leachate.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Removal mechanism of trace oxytetracycline by aerobic sludge

To investigate the mechanism of removal of selected pharmaceuticals in activated sludge systems, laboratory-scale batch experiments were conducted to assess the adsorption and degradation behavior of trace oxytetracycline (OTC). The adsorption equilibrium of OTC was observed in 30 min and the adsorption process could be well described by a pseudo-second-order model with a rate of 0.362 L μg^?1 min^?1. The OTC adsorption rate decreased with increasing temperature and could be fitted by the Freundlich isotherm. The linear partition coefficients (K_d) were 1.19, 0.999, and 0.841 L g^?1 at temperatures of 15, 20, and 25 °C, respectively. Thermodynamic analysis revealed that the adsorption of OTC onto the inactivated sludge was spontaneous (ΔG = ?16.7 to ?17.0 kJ mol^?1), enthalpy-driven (ΔH = ?24.9 kJ mol^?1), entropy-retarded (ΔS = ?27.4 J (mol K)^?1), and predominantly a physical adsorption.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Pretreatment of municipal landfill leachate by a combined process

Biodegradability enhancement of landfill leachate using air stripping followed by coagulation/ultrafiltration (UF) processes was introduced. The air stripping process obtained a removal efficiency of 88.6% for ammonia nitrogen (NH₄–N) at air-to-liquid ratio of 3500 (pH 11) for stripping 18 h. The single coagulation process increased BOD/COD ratio by 0.089 with the FeCl₃ dosage of 570 mg l^?1 at pH 7.0, and the single UF process increased the BOD/COD ratio to 0.311 from 0.049. However, the combined process of coagulation/UF increased the BOD/COD ratio from 0.049 to 0.43, and the final biological oxygen demand (BOD), chemical oxygen demand (COD), NH₄–N and colour of leachate were 1223.6 mg l^?1, 2845.5 mg l^?1, 145.1 mg l^?1 and 2056.8, respectively, when 3 kDa molecular weight cut-off (MWCO) membrane was used at the operating pressure 0.7 MPa. In ultrafiltration process, the average solution flux (J_V), concentration multiple (M_C) and retention rate (R) for COD was 107.3 l m^?2 h^?1, 6.3% and 84.2%, respectively.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Optimizing the preparation parameters of mesoporous nanocrystalline titania and its photocatalytic activity in water: Physical properties and growth mechanisms

Titania nanomaterial with an anatase structure and 5.6 nm crystallite size and 280.7 m² g⁻¹ specific surface areas had been successfully prepared by sol–gel/hydrothermal route. The effect of pH as a type of autoclave and calcination was studied. Crystallite size and phase composition of the prepared samples were identified. X-ray diffraction analyses showed the presence of anatase with little or no rutile phases. The crystallite size of the prepared TiO₂ with acidic catalyst was both smaller than that prepared with basic catalyst, and was increasing after acidic calcinations by a factor 4–5. Basic calcinations produced a specific increase of 1.5. Rutile ratio and the particle size were increased after calcination at 500 °C. However, TiO₂ powder synthesized using a basic catalyst persisted the anatase phase and a loosely aggregation of particles. Anatase TiO₂ as prepared with acidic catalyst in Teflon lined stainless steel autoclave demonstrated the highest photocatalytic activity for degradation of 2,6-dichlorophenol-indophenol under ultraviolet irradiation with t_½ 0.8 min.     

Refinery wastewater degradation with titanium dioxide,zinc oxide,and hydrogen peroxide in a photocatalytic reactor

This paper presents the photo-catalytic degradation of real refinery wastewater from National Refinery Limited (NRL) in Karachi, Pakistan, using TiO₂, ZnO, and H₂O₂. The pretreatment of the refinery effluent was carried out on site and pretreated samples were tested at 32–37 °C in a stirrer bath reactor by using ultra-violet photo oxidation process. The degradation of wastewater was measured as a change in initial chemical oxygen demand (COD) and with time. Optimal conditions were obtained for catalyst type, and pH. The titanium dioxide proved to be very effective catalysts in photo-catalytic degradation of real refinery wastewater. The maximum degradation achieved was 40.68% by using TiO₂ at 37 °C and pH of 4, within 120 min of irradiations. When TiO₂ was combined with H₂O₂ the degradation decreased to 25.35%. A higher reaction rate was found for titanium dioxide. The results indicate that for real refinery wastewater, TiO₂ is comparatively more effective than ZnO and H₂O₂. The experiments indicated that first-order kinetics can successfully describe the photo-catalytic reaction. The ANOVA results for the model showed satisfactory and reasonable adjustment of the second-order regression model with the experimental data. The ANOVA results also showed that pH is significant than reaction time and catalyst dosage of TiO₂; and in case of ZnO, reaction time is significant than pH and catalyst dosage. This study proves that real refinery wastewater reacts differently than synthetic refinery wastewater, oil field produced water or oil water industrial effluent.     

Optimization and evaluation of an air-recirculated stripping for ammonia removal from the anaerobic digestate of pig manure

An air-recirculated stripping involved two processes and did not require any pretreatment. First, stripping CO₂ decreased the buffer capacity of the anaerobic digestate, thereby reducing the amount of lime used to achieve a high pH. Second, lime was added to increase pH and remove ammonia from the anaerobic digestate of pig manure. pH increased from 8.03 to 8.86 by stripping CO₂ in the first process (gas-to-liquid ratio = 180) and further reached 12.38 in the second process (gas-to-liquid ratio = 300). During process optimization, the maximum ammonia removal efficiency reached 96.78% with a lime dose of 22.13 g. The value was close to 98.25%, which was the optimal result predicted by response surface methodology using the software Design-Expert 8.05b. All these results indicated that air-recirculated stripping coupled with absorption was a promising technology for the removal and recovery of nitrogen in the anaerobic digestate of pig manure.     

Evaluation of Abelmoschus esculentus (lady's finger) seed as a novel biosorbent for the removal of Acid Blue 113 dye from aqueous solutions

The use of a new biosorbent derived from Abelmoschus esculentus (A. esculentus) seed for the removal of Acid Blue 113 (AB113) in aqueous solutions was investigated in batch mode. Biosorption studies were carried out under varying operational parameters including initial pH, biosorbent dosage, contact time, initial dye concentration and temperature. The results indicated that the biosorption properties were strongly dependent on initial pH. Fourier transform infrared spectroscopy analysis revealed that hydroxyl, carboxylic and amide functional groups present on the biosorbent surface were involved in the dye removal process. Equilibrium data were best fitted by the Langmuir model. The maximum biosorption capacity was 169.9 ± 3.1 mg g⁻¹ at 25 °C and initial pH 5.5. The kinetic data were in good agreement with the pseudo-second-order kinetic model. The process was controlled by diffusion through boundary layer at the initial stage followed by intra-particle diffusion at the later stage. Thermodynamic evaluation showed that the process was endothermic and spontaneous. The present study suggests that A. esculentus seed with maximum biosorption capacity which compared well with values reported in the literature can be a potential biosorbent for AB113 dye removal.     

Propagation of ethylene–air flames in closed cylindrical vessels with asymmetrical ignition

A study of explosions in several elongated cylindrical vessels with length to diameter L/D = 2.4–20.7 and ignition at vessel's bottom is reported. Ethylene–air mixtures with variable concentration between 3.0 and 10.0 vol% and pressures between 0.30 and 1.80 bara were experimentally investigated at ambient initial temperature. For the whole range of ethylene concentration, several characteristic stages of flame propagation were observed. The height and rate of pressure rise in these stages were found to depend on ethylene concentration, on volume and asymmetry ratio L/D of each vessel. High rates of pressure rise were found in the early stage; in later stages lower rates of pressure rise were observed due to the increase of heat losses. The peak explosion pressures and the maximum rates of pressure rise differ strongly from those measured in centrally ignited explosions, in all examined vessels. In elongated vessels, smooth p(t) records have been obtained for the explosions of lean C₂H₄–air mixtures. In stoichiometric and rich mixtures, pressure oscillations appear even at initial pressures below ambient, resulting in significant overpressures as compared to compact vessels. In the stoichiometric mixture, the frequency of the oscillations was close to the fundamental characteristic frequency of the tube.     

Nursing student evaluation of NIOSH workplace violence prevention for nurses online course

Introduction: As primary targets of workplace violence in health care settings, nurses may suffer negative physical and psychological consequences. NIOSH created an online course to educate nurses about violence prevention techniques. Method: A mixed-methods approach assessed workplace violence awareness and knowledge among nursing students. A pre/post/post-test survey and focus group discussions evaluated participant awareness and knowledge, assessed course design, and solicited recommendations for increasing participation and strategies for improving message retention. Results: The mean awareness scores differed significantly between pre-course and both post-course time points (Wilk's λ = 0.319, F(2, 46) = 49.01, p < 0.001). Post hoc tests using the Bonferroni correction revealed that course participation increased awareness of workplace violence from pre-course scores (M = 0.75, SD = 0.438) to immediate post-course (M = 2.13, SD = 0.789) and four-week post-course (M = 1.96, SD = 0.771) scores on a 3-item measure. Similarly, mean knowledge scores increased between pre-course and both post-course time points (Wilk's λ = 0.495, F(1.57, 73.66) = 37.26, p < 0.001). Post hoc tests using the Bonferroni correction revealed that course participation increased knowledge of workplace violence from pre-course scores (M = 6.65, SD = 1.45) to immediate post-course (M = 8.56, SD = 1.32) and four-week post-course (M = 8.19, SD = 1.42) scores on a 10-item measure. Qualitative data from the focus groups reinforced the quantitative findings. Participants citing benefits from the content strongly recommended including the course in nursing curriculums. Incorporating the course early in the nursing educational experience will better prepare students to deal with workplace violence when they enter health care professions. Conclusions: The results indicate that NIOSH and its partners created an effective online workplace violence awareness and prevention course. Practical applications: Nursing students and professionals can be effectively educated about workplace violence using an online format.     

Conscientious personality and young drivers' crash risk

Introduction: Personality characteristics are associated with many risk behaviors. However, the relationship between personality traits, risky driving behavior, and crash risk is poorly understood. The purpose of this study was to examine the association between personality, risky driving behavior, and crashes and near-crashes, using naturalistic driving research methods. Method: Participants' driving exposure, kinematic risky driving (KRD), high-risk secondary task engagement, and the frequency of crashes and near-crashes (CNC) were assessed over the first 18 months of licensure using naturalistic driving methods. A personality survey (NEO-Five Factor Inventory) was administered at baseline. The association between personality characteristics, KRD rate, secondary task engagement rate, and CNC rate was estimated using a linear regression model. Mediation analysis was conducted to examine if participants' KRD rate or secondary task engagement rate mediated the relationship between personality and CNC. Data were collected as part of the Naturalistic Teen Driving Study. Results: Conscientiousness was marginally negatively associated with CNC (path c = − 0.034, p = .09) and both potential mediators KRD (path a = − 0.040, p = .09) and secondary task engagement while driving (path a = − 0.053, p = .03). KRD, but not secondary task engagement, was found to mediate (path b = 0.376, p = .02) the relationship between conscientiousness and CNC (path c′ = − 0.025, p = .20). Conclusions: Using objective measures of driving behavior and a widely used personality construct, these findings present a causal pathway through which personality and risky driving are associated with CNC. Specifically, more conscientious teenage drivers engaged in fewer risky driving maneuvers, and suffered fewer CNC. Practical Applications: Part of the variability in crash risk observed among newly licensed teenage drivers can be explained by personality. Parents and driving instructors may take teenage drivers' personality into account when providing guidance, and establishing norms and expectations about driving.     

The investigation of correlated factors of external explosion during the venting process

Experimental investigations were done in the paper for the process of venting explosion in a ϕ200 mm×400 mm cylindrical vessel. Compared with the normal venting process, the phenomenon of external explosion was observed and discussed first. Moreover, when CH₄–air mixture gases were used and the vent diameter was 55 mm, three kinds of condition were selected: ϕ=0.8, ϕ=1.0 and ϕ=1.3. And two ignition positions were selected: at the vessel center and at the bottom. Then the venting processes influenced by these factors were experimented and discussed, too.     

Ion exchange membrane-assisted electro-activation of aqueous solutions: Effect of the operating parameters on solutions properties and system electric resistance

The properties of electro-activated (EA) aqueous solutions as well as the dynamics of their changes were considered in the current study using aqueous solutions of NaCl and NaHCO₃. The concentrations of the salt solutions were 0.5, 0.25, 0.125 and 0.05 M. The tests were performed at the DC current densities of 25, 37.5, and 50 Å/m². The electro-activation reactor consisted of three individual cells assembled together and separated by anion-exchange (AEM) and cation-exchange (CEM) membranes. During the experiments, four configurations of the membrane placements and solutions concentrations were studied. The obtained results showed the dynamics of the electro-activation process that allows obtaining electro-activated solutions with targeted properties such as pH and oxydo-reduction potential (ORP). It was possible to obtain electro-activated solutions at the anodic side (acid anolyte) with pH of 3.0, 3.5, and 4.0 and ORP of +1100 ± 15 mV when NaCl solution was used as electrolyte. Furthermore, several types of electro-activated solutions with high redox potential (ORP = +921 ± 12 mV) and neutral pH (6.48 ± 0.05) were obtained on the anode side when sodium carbonate was used. At the same time, two types of solutions, one with acid pH (2.14 ± 0.14) and the other one with alkaline pH (10.46 ± 0.03) with ORP = +689 ± 10 and 110 ± 21 mV, respectively, were obtained in the central compartment which considered as electro-activated solutions obtained by means of noncontact electro-activation.     

The self-defensive attribution hypothesis in the work environment: Co-workers’ perspectives

The study explored the possible influences of situational, personal and non-relevant perception on causality attributions and responsibility assignment in Ghana’s work environment. Ghanaian industrial workers (co-workers) who were witnesses to industrial accidents (n = 117) assigned causality for the mishap and their responses were compared. Analyses were based on the co-workers’ responses to open-ended questions. Three categories of co-workers were identified and labelled as situationally relevant (n = 34), personally relevant (n = 43) and non-relevant co-workers (n = 40). The results showed that co-workers (witnesses) who had some perception of situational and or personal relevance with the accident victims attributed less responsibility to the accident victims than did their counterparts who had no perception of relevance. This observation, like other motivated attributional distortions, seems to reflect a tendency towards self-protection from the three categories of co-workers. It confirms the self-defensive attribution hypothesis in causal attributions about accidents in the work environment.