Recovery of methyl orange and Congo red from aqueous solutions using tri-octyl amine (TOA) in benzene as carrier

The recovery of anionic azo dyes namely Congo red (CR), methyl orange (MO) from acidic aqueous solutions using tri-octyl amine (TOA) as an extractant has been investigated. The percentage of extraction of MO and CR increases with an increasing TOA concentration. The anionic dyes were extracted from aqueous solution at pH 2.0 ± 0.1. The extracted dye has been back extracted into aqueous solutions using sodium hydroxide, sodium carbonate and sodium bicarbonate. The organic phase obtained after the stripping of dyes was washed with dilute sodium hydroxide solution to neutralize any sulphuric acid trapped or adhered to the solvent and then with distilled water. This solvent was reused in succeeding extraction of dyes. The influencing parameters were; the effect of diluents, effect of extractant concentration, effect of pH, effect of interference study, effect of equilibrium time, various stripping reagents and stripping phase ratio. The characterization studies such as UV and IR spectra of extracted and stripped MO and CR was also studied.     

Evaluation of Abelmoschus esculentus (lady's finger) seed as a novel biosorbent for the removal of Acid Blue 113 dye from aqueous solutions

The use of a new biosorbent derived from Abelmoschus esculentus (A. esculentus) seed for the removal of Acid Blue 113 (AB113) in aqueous solutions was investigated in batch mode. Biosorption studies were carried out under varying operational parameters including initial pH, biosorbent dosage, contact time, initial dye concentration and temperature. The results indicated that the biosorption properties were strongly dependent on initial pH. Fourier transform infrared spectroscopy analysis revealed that hydroxyl, carboxylic and amide functional groups present on the biosorbent surface were involved in the dye removal process. Equilibrium data were best fitted by the Langmuir model. The maximum biosorption capacity was 169.9 ± 3.1 mg g⁻¹ at 25 °C and initial pH 5.5. The kinetic data were in good agreement with the pseudo-second-order kinetic model. The process was controlled by diffusion through boundary layer at the initial stage followed by intra-particle diffusion at the later stage. Thermodynamic evaluation showed that the process was endothermic and spontaneous. The present study suggests that A. esculentus seed with maximum biosorption capacity which compared well with values reported in the literature can be a potential biosorbent for AB113 dye removal.     

Evaluating the efficacy of alumina/carbon nanotube hybrid adsorbents in removing Azo Reactive Red 198 and Blue 19 dyes from aqueous solutions

Concerning the high volume of wastewater containing dye in Iran and its adverse effects, it is necessary to develop scientific solutions for treating these wastewaters. The aim of this study was to evaluate the efficiency of the alumina-coated multi-walled carbon nanotubes in removing the Reactive Red 198 (RR 198) and Blue 19 (RB 19) dyes. Synthetic samples including dye with different concentrations were prepared. These samples were put in contact with different contents of alumina/multi-walled carbon nanotubes, in different pH values, in different contact times, different temperatures and the presence of sodium sulfate or sodium carbonate. The optimum pH, dye concentration and temperature for removal of the two dyes was 3, 50 mg l⁻¹ and 25 °C, respectively. The optimum adsorbent dose for removal the RR 198 dye was 0.5 g l⁻¹ and for Blue 19 was 0.4 g l⁻¹. The optimum contact time for RR 198 was 150 min and RB 19 was 180 min. In this condition, maximum removal efficiency for RR 198 and RB 19 was 91.54% and 93.51%, respectively. The adsorption study was analyzed kinetically, and the results revealed that the adsorption fitted a pseudo-second order kinetic model. According to these results alumina/multi-walled carbon nanotubes can effectively remove RR 198 and RB 19 from aqueous solutions.     

Magnetophoretic separation of Chlorella sp.: Role of cationic polymer binder

Cationic polyelectrolyte promoted effective attachment of iron oxide nanoparticles (IONPs) onto microalgal cells through electrostatic attraction. Poly(diallyldimethylammonium chloride) (PDDA) and chitosan (ChiL), both are cationic polymer, are feasible to act as binding agent to promote rapid magnetophoretic separation of Chlorella sp. through low gradient magnetic separation (LGMS) with field gradient ▿B less than 80 T/m in real time. Cell separation efficiency up to 98% for the case of PDDA and 99% for the case of ChiL can be achieved in 6 min when 3 × 10⁷ cells/mL Chlorella sp. are exposed to 300 mg/L surface functionalized-IONPs (SF-IONPs). Different polyelectrolytes do not give significant effect on cell separation efficiency as long as the particle attachment occurred. However, the PDDA is more preferable as the binder for all type of microalgae medium than the chitosan (ChiL) since it is not pH dependent. SF-IONPs coated with PDDA guarantee the cell separation performance for all pH range of cell medium, with 98.21 ± 0.40% at pH 8.84. On the other hand, the ChiL performance will be affected by the cell medium pH, with only 22.93 ± 31.03% biomass recovery at pH 9.25.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Achieving stable partial nitritation using endpoint pH control in an SBR treating landfill leachate

The feasibility of using endpoint pH control to achieve stable partial nitritation (PN) in an SBR for landfill leachate treatment was investigated. By imposing a fixed-time anoxia followed by variable-time aeration in an SBR cycle, successful partial nitritation was maintained for 182 days at a nitrogen loading rate of 0.30–0.89 kg/m³/day. The effluent NO₂⁻-N/NH₄⁺-N ratio and the effluent NO₃⁻-N concentration were 1.30 ± 0.22 and 16 ± 9 mg/L, respectively. High free ammonia (FA) and low dissolved oxygen (DO) concentrations were inhibition factors of nitrate formation. The termination of aeration at a suitable endpoint pH was the key to achieve an effluent NO₂⁻-N/NH₄⁺-N ratio close to the stoichiometric value. This endpoint pH control strategy represents practical potentials in the engineered application of combined PN–ANAMMOX processes.     

Partial nitritation of landfill leachate with varying influent composition under intermittent aeration conditions

The start-up and operation of a partial nitritation sequencing batch reactor for the treatment of landfill leachate were carried out on intermittent aeration mode. Partial nitrite accumulation was established in 15 days after the mode was changed from continuous aeration to intermittent aeration. Despite the varying influent composition, partial nitritation could be maintained by adjusting the hydraulic retention time (HRT) and the air flow rate. An increase in the air flow rate together with a decrease in air off duration can improve the partial nitritation capacity and eventually result in the development of granular sludge with fine diameters. A nitrogen loading rate of 0.71 ± 0.14 kg/m³/d and a COD removal rate of 2.21 ± 0.13 kg/m³/d were achieved under the conditions of an air flow rate of 19.36 ± 1.71 m³ air/m³/h and an air on/off duration of 1.5 min/0.7 min. When the ratio of total air flux (TAF) to the influent loading rate (ILR) was controlled at the range of 163–256 m³ air/kg COD, a stable effluent NO₃^?–N/NO_x^?–N (NO₂^?–N plus NO₃^?–N) ratio below 13% was achieved. Interestingly, the effluent pH was found to be a good indicator of the effluent NO₂^?–N/NH₄⁺–N ratio, which is an essential parameter for a subsequent anaerobic ammonium oxidation (Anammox) reactor.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Synthesis of hydroxyapatite/clay and hydroxyapatite/pumice composites for tetracycline removal from aqueous solutions

Synthesized hydroxyapatite/clay (HA-C) and hydroxyapatite/pumice (HA-P) composites were used for tetracycline (TC) uptake studies from aqueous solution and their uptake capacities were compared. HA-C and HA-P composites were synthesized by precipitation method and the structures of the synthesized composites were characterized by XRD, SEM and BET analyses. Cation exchange capacities of HA-C and HA-P were found to be 84 meq/100 g and 33 meq/100 g, respectively. The TC adsorption using HA-C and HA-P was studied on batch mode. Various parameters such as contact time, solution pH, initial TC concentration, composite dosage, salinity and temperature were optimized. Langmuir, Freundlich and Dubinin–Radushkevich (D–R) isotherm models were applied to the equilibrium data. The maximum adsorption capacity onto HA-C was found to be 76.02 mg/g and about four times larger than the adsorption capacity of the HA-P (17.87 mg/g). The results indicated that the TC uptake onto HA-C and HA-P composites is mainly by a surface complexation and ion-exchange mechanism which depend on the solution pH. The calculated values of thermodynamic parameters indicated that the TC adsorption is favorable, physicochemical in nature. The sorption process follows pseudo-second-order and intraparticle diffusion kinetic models. The TC adsorption mechanism by HA-C and HA-P has been proposed.     

Adsorptive removal of basic dyes from aqueous solutions by surfactant modified bentonite clay (organoclay): Kinetic and competitive adsorption isotherm

Cationic surfactant (Hexadecyltrimenthylammonium chloride) modified bentonite clay was prepared and systematically studied for its adsorption behavior as an efficient adsorbent for the removal of basic dyes such as methylene blue (MB), crystal violet (CV) and Rhodamine B (RB) from aqueous phase. Organo modified clay shows better capacity for the removal of three dyes. The adsorption process was found to be dependent on pH and initial dye concentration. The maximum dye sorption was found to be at a pH of 9.0 (99.99% for MB, 95.0% for CV and 83.0% for RB). The adsorption capacity for the dyes was found to be 399.74, 365.11 and 324.36 μmol/g for MB, CV and RB, respectively at 30 °C. The equilibrium uptake was attained within 240 min. The kinetic studies were revealed that sorption follows a pseudo-second-order kinetic model which indicates chemisorption between adsorbent and adsorbate molecules. Adsorption isotherm indicates non-energetically adsorption sites which fit with Freundlich isotherm model. The fitness of kinetics and isotherm models was evaluated by using HYBRID error analysis function. Competitive adsorptions of dyes were studied by using binary component systems.     

Prevalence of work-site injuries and relationship between obesity and injury among U.S. workers: NHIS 2004–2012

Introduction: Studies have reported associations between obesity and injury in a single occupation or industry. Our study estimated the prevalence of work-site injuries and investigated the association between obesity and work-site injury in a nationally representative sample of U.S. workers. Methods: Self-reported weight, height, and injuries within the previous three months were collected annually for U.S. workers in the National Health Interview Survey (NHIS) from 2004–2012. Participants were categorized as normal weight (BMI: 18.5–24.9 kg/m²), overweight (BMI: 25.0–29.9), obese I (BMI: 30.0–34.9), and obese II (BMI: 35 +). The prevalence of injury and prevalence ratios from fitted logistic regression models was used to assess relationships between obesity and injury after adjusting for covariates. Sampling weights were incorporated using SUDAAN software. Results: During the 9-year study period from 2004 to 2012, 1120 workers (78 workers per 10,000) experienced a work-related injury during the previous three months. The anatomical sites with the highest prevalence of injury were the back (14.3/10,000 ± 1.2), fingers (11.5 ± 1.3), and knees (7.1 ± 0.8). The most common types of injuries were sprains/strains/twists (41.5% of all injuries), cuts (20.0%), and fractures (11.8%). Compared to normal weight workers, overweight and obese workers were more likely to experience work-site injuries [overweight: PR = 1.25 (95% CI = 1.04–1.52); obese I: 1.41 (1.14–1.74); obese II: 1.68 (1.32–2.14)]. These injuries were more likely to affect the lower extremities [overweight: PR = 1.48, (95% CI = 1.03–2.13); obese I: 1.70 (1.13–2.55); obese II: 2.91 (1.91–4.41)] and were more likely to be due to sprains/strains/twists [overweight: PR = 1.73 (95% CI = 1.29–2.31); obese I: PR = 2.24 (1.64–3.06); obese II: PR = 2.95 (2.04–4.26)]. Conclusions: Among NHIS participants, overweight and obese workers were 25% to 68% more likely to experience injuries than normal weight workers. Practical applications: Weight reduction policies and management programs may be effectively targeted towards overweight and obese groups to prevent or reduce work-site injuries.     

Investigation on removal of p-nitrophenol using a hybridized photo-thermal activated persulfate process: Central composite design modeling

The aim of this work is the study of p-nitrophenol (PNP) removal, as a nitroaromatic compound, using a hybridized photo-thermally activated potassium persulfate (KPS) in a fully recycled batch reactor. Response surface method was used for modeling the process. Reaction temperature, KPS initial dosage and initial pH of the solution were selected as variables, besides PNP degradation efficiency was selected as the response. ANOVA analysis reveals that a second order polynomial model with F-value of 41.7, p-value of 0.0001 and regression coefficient of 0.95 is able to predict the response. Based on the model, the process optimum conditions were introduced as initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 66 °C. Also experiments showed that using thermolysis and photolysis of the persulfate simultaneously, the role of thermolysis is not considerable. A pseudo first order kinetic model was established to describe the degradation reaction. Operational cost, as a vital industrial criterion, was estimated so that the condition of initial pH of 4.5, [KPS]₀ = 1452 mg/L and T = 25 °C showed the highest cost effective case. Under the preferred mild condition, the process will reach to 84% and 89% of degradation and mineralization efficiencies, after 60 and 120 min, respectively.     

Biohydrogen production using waste activated sludge as a substrate from fructose-processing wastewater treatment

Biohydrogen production by dark fermentation in a series of batch tests under different environmental control conditions was evaluated to determine the optimal initial cultivation pH and temperature for a continuous-flow kinetic test to validate the kinetic model system. The waste activated sludge (WAS) from fructose-processing manufacturing was used as the model substrate for biohydrogen production. The batch experiments for biohydrogen production were conducted in a 6 l bioreactor. Fifteen batch kinetic tests were investigated when pH was controlled at 6, 7, 8 and 9 as well as the temperature was controlled at 37 °C, 45 °C and 55 °C, respectively. The experimental results indicated that the optimal operational condition for hydrogen production occurred while pH was 7 and temperature was 55 °C with the highest hydrogen production of 7.8 mmol. The optimal recovery time for hydrogen was 25 h in the batch experiments. Furthermore, the kinetic test of biohydrogen production was performed by anaerobic mixed microbial culture in the continuous-flow experiment when pH and temperature was maintained at 7 and 55 °C. Approximately 60% and 7% of substrate solution was converted into acetate and hydrogen, respectively, at the steady state. Roughly only 0.77% and 2.7% of substrate solution was converted into propionate and butyrate, respectively, at a steady-state condition. The experimental and modeling approaches presented in this study could be employed for the design of pilot-scale and full-scale anaerobic biohydrogen fermentors using food-processing waste activated sludge (WAS) as a substrate solution.     

Anaerobic digestion modeling of the main components of organic fraction of municipal solid waste

The organic fraction of municipal solid waste (OFMSW) is composed of several heterogeneous organic and inorganic wastes. The diversity of composition, the high volatile solid content and the biodegradable material that this waste offers make it quite an interesting option for anaerobic digestion (AD). Depending on the substrate composition, the biological degradation and kinetics of the AD could vary. Biochemical methane potential (BMP) tests are used as a tool to evaluate the methane production of several fractions of OFMSW, in order to study the influence of each fraction in the final mixture. The kinetic parameters of methane curves and the prediction of final productions are studied by different approaches to model equations using linear, exponential, logistic and Gaussian models. The analyses of the fractions indicate that organic substrates such as meat/fish which are in a small proportion in the final mixture, obtain major productivities (291 ± 3 mlCH₄/gVS), however others such as paper (217 ± 5 mlCH₄/gVS) could have their productivity enhanced due to their high VS present in the final mixture. Both the Gomperzt and the first order model fit reasonably with all the fractions, although substrates with lag phase adjust only to the Gompertz model explaining 99% of the experimental results.     

Pb(II) adsorption from aqueous solutions by raw and treated biomass of maize stover – A comparative study

The potential to remove Pb(II) ion from wastewater treatment systems using raw and treated maize stover through adsorption was investigated in batch experiments. To achieve this, batch mode experiments were conducted choosing specific parameters such as pH (2–8), dosage concentration (2–30 g L⁻¹), contact time (5–180 min), temperature (20–45 °C) and metal ion concentrations (10–50 mg L⁻¹). Adsorption was pH-dependent showing a maximum at pH value 5. The equilibrium sorption capacities of raw and treated maize stover were 19.65 and 27.10 mg g⁻¹, respectively. The adsorption data fitted well to the Langmuir isotherm model. Kinetic studies revealed that the adsorption process followed pseudo-second-order model. The calculated thermodynamic parameters showed that the adsorption of Pb(II) was spontaneous and exothermic in nature. Consequently, this study demonstrated that both raw and treated maize stover could be used as adsorbents for the treatment of Pb(II) from industrial wastewaters.     

Improving disintegration and acidification of waste activated sludge by combined alkaline and microwave pretreatment

The individual alkaline or microwave pretreatment has been proved to be effective in disintegration and acidification of waste activated sludge (WAS). In this study, the effects of combined alkaline and microwave pretreatment at different pH and specific energy input (Es) on WAS disintegration were investigated using response surface methodology (RSM). Combined pretreatment achieved disintegration degree (DD) of 65.87% at Es of 38,400 kJ/kg TS and pH 11.0. The ANOVA further demonstrated that pH showed more significant effect on DD than Es. Anaerobic batch experiment results showed that combined pretreatment not only significantly improved volatile fatty acids (VFAs) accumulation but also shortened the time for the highest VFAs accumulation. The maximal VFAs accumulation (1500 mg COD/L) obtained at Es of 28,800 kJ/kg TS and fermentation time of 72 h, which was about two times that of the treatment without microwave (850 mg COD/L) at 96 h. The analysis of VFAs composition showed that the VFAs mainly consisted of acetic and iso-valeric acids, accounting for 57.3–70.1% of total VFAs.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Boron removal from produced water using electrocoagulation

Produced water is the largest wastestream of oil and gas exploration but its chemical composition hinders its beneficial use. Effective treatment and reuse of produced water can mitigate scarcity of fresh water, especially in arid areas. Presence of inorganic compounds such as boron in produced water renders its beneficial use difficult. In this study, boron removal from produced water was investigated. Synthetic wastewater was prepared simulating the range of boron concentrations in produced water. Four operating parameters pH (3–11), charge loading (1200–3600 Ah/m³), contact time (15–90 min) and concentration (10–30 mg/L) were selected and their optimum conditions investigated. The obtained optimum conditions were applied to treat real produced water. Residual boron concentration of 0.3 mg/L was obtained from initial boron concentration of 15 mg/L in real produced water at optimum conditions of pH 7, charge loading 2400 Ah/m³ and contact time 90 min. Boron adsorption could be represented by Langmuir and Freundlich isotherm models. Electrocoagulation can be used for the effective removal of boron from produced water.     

Development and physicochemical characterization of a new magnetic nanocomposite as an economic antibiotic remover

Maghemite (ϒ-Fe₂O₃) nanoparticles were impregnated to nanoporous carbon obtained from tomato waste (TWNC). The prepared magnetic composite (MTWNC) was characterized and used to remove tetracycline (TC) from water and then easily be separated from the medium by a magnetic technique. The morphologies and surface chemistries of both magnetic and non-magnetic nanoporous carbons were studied by FTIR, XRD, SEM, SEM-EDX, VSM, BET surface area, proximate and elemental analysis determinations. Batch adsorption studies were carried out and the effects of pH, initial TC concentration, adsorbent dose, ionic strength and temperature were investigated. The adsorption kinetics of TC on MTWNC could be expressed well by the pseudo-second order model, and sorption isotherms were described by Langmuir equation with maximum adsorption capacity of 60.60 mg/g at pH 4 and 50 °C. Thermodynamic parameters showed that the adsorption of TC onto MTWNC was feasible, spontaneous and endothermic. Furthermore, the recyclability of the adsorbent was tested with 0.01 M NaOH solution, and the results show that the synthesized composite adsorbent could be employed repeatedly in wastewater treatment.     

Removal of toluene vapour from air stream using a biofilter packed with polyurethane foam

Biodegradation of toluene vapour was investigated for 168 days in a polyurethane packed biofilter inoculated with a mixed microbial population. Biofilter consisted of five square cross-section modular units each of size 0.16 m × 0.16 m × 0.20 m and filled with the polyurethane foam cubes up to a height of 0.15 m. Inlet concentration of toluene was varied from 0.04 to 2.5 g m^?3 and the volumetric flow rate of toluene loaded air from 0.06 to 0.90 m³ h^?1.Depending upon initial loading rates, removal efficiency ranging from 68.2 to 99.9% and elimination capacity ranging from 10.85 to 90.48 g h^?1 m^?3 were observed during steady state operations. More than 90% removal efficiency was observed up to an inlet loading rate of 76.3 g h^?1 m^?3. High carbon recovery (>90%) indicated effective biodegradation in the bed. Low variation of pH (7.2–8.8) and pressure drop (45.8–76.3 Pa) was observed. The stability of the biomass was evident from the fast response of the biofilter to shutdown and restartup.