Inerting characteristics of ultrafine Mg(OH)2 on starch dust explosion flame propagation

Experiments on the flame propagation of starch dust explosion with the participation of ultrafine Mg(OH)₂ in a vertical duct were conducted to reveal the inerting evolution of explosion processes. Combining the dynamic behaviors of flame propagation, the formation law of gaseous combustion products, and the heat dissipation features of solid inert particles, the inerting mechanism of explosion flame propagation is discussed. Results indicate that the ultrafine of Mg(OH)₂ powders can cause the agglomeration of suspended dust clouds, which makes the flame combustion reaction zone fragmented and forms multiple small flame regions. The flame reaction zone presents non-homogeneous insufficient combustion, which leads to the obstruction of the explosion flame propagation process and the obvious pulsation propagation phenomenon. As the proportion of ultrafine Mg(OH)₂ increases, flame speed, flame luminescence intensity, flame temperature and deflagration pressure all show different degrees of inerting behavior. The addition of ultrafine Mg(OH)₂ not only causes partial inerting on the explosion flame, but also the heat dissipation of solid inert particles affects the acceleration of its propagation. The explosion flame propagation is inhibited by the synergistic effect of inert gas-solid phase, which attenuates the risk of starch explosion. The gas-solid synergistic inerting mechanism of starch explosion flame propagation by ultrafine Mg(OH)₂ is further revealed.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

PAN dust explosion inhibition mechanisms of NaHCO3 and Al(OH)3

We investigate the PAN dust explosion inhibition behaviors of NaHCO₃ and Al(OH)₃ in a 20 L spherical explosion system and a transparent pipe explosion propagation test system. The results show that, in the standard 20 L spherical explosion system, the highest PAN dust explosion concentration is 500 g/m³, the maximum explosion pressure is 0.661 MPa, and the maximum explosion pressure increase rate is 31.64 MPa/s; adding 50% NaHCO₃ and 60% Al(OH)₃ can totally inhibit PAN dust explosion. In the DN0.15 m transparent pipe explosion propagation test system, for 500 g/m³ PAN dust, the initial explosion flame velocity is 102 m/s, the initial pressure is 0.46 MPa, and the initial temperature is 967 °C; adding 60% NaHCO₃ and 70% Al(OH)₃ can totally inhibit PAN dust explosion flames. Through FTIR and TG analyses, we obtain the explosion products and pyrolysis patterns of the explosion products of PAN dust, NaHCO₃, and Al(OH)₃. On this basis, we also summarize the PAN dust explosion inhibition mechanisms of NaHCO₃ and Al(OH)₃.     

Preparation and performance of novel APP/NaY–Fe suppressant for coal dust explosion

Coal dust explosion occurs easily in the coal chemical industry. To ensure safety in industrial production, NaY zeolite was used as carrier modified with Fe ions and combined with ammonium polyphosphate (APP) to prepare a novel composite suppressant for coal dust explosion. The explosion suppression performance of novel APP/NaY–Fe suppressant was investigated by flame propagation inhibition experiments. The results show that Fe ion modification can effectively improve the explosion suppression performance. By increasing content, the explosion suppression performance of the explosion suppressant increases. The maximum explosion pressure P_max of coal dust drops to 0.13 MPa when 50 wt% explosion suppressants were added, and the coal dust explosion cannot continue to expand. Complete suppression of explosion could be achieved by adding 66 wt% explosion suppressants. Combined with XRD, SEM and TG results, the explosion suppression mechanism was proposed. The novel explosion suppressant has high thermal stability, good dispersity and its explosion suppression components distribute uniformly. It shows good explosion suppression performance by the synergistic effect among explosion-suppression components.     

High efficiency of the NH4H2PO4/Mg(OH)2 composite for guaranteeing safety of wood production

Currently, China's timber industry is in high demand with the development of real estate. However, there is a certain fire hazard in the production process of wood manufacturing. Once a fire occurs, the fire is violent and the spread is rapid. Therefore, to improve the safety of its production process, ammonium dihydrogen phosphate and magnesium hydroxide were selected to prepare a new composite superfine dry powder, which was denoted as the NH₄H₂PO₄/Mg(OH)₂ composite. Furthermore, to figure out dry powders' extinction effect on Class A fire, the wood-crib fire suppression effect of the NH₄H₂PO₄/Mg(OH)₂ composite was test, and then compared with that of ultrafine dry powder (UDP) and commercial ABC dry powder (C-ABC) in a 1 m³ chamber. Three parameters of the fire extinguishing process, namely flame extinction time, powder consumption and temperature drop were adopted to measure the fire suppression performance. The results demonstrated that UDP and C-ABC both had a larger flame extinction time and powder consumption than the NH₄H₂PO₄/Mg(OH)₂ composite. Besides, a fire (wood cribs) can be extinguished by the NH₄H₂PO₄/Mg(OH)₂ composite with the fastest temperature drop and a much-improved toxic gas suppression ability. In short, the NH₄H₂PO₄/Mg(OH)₂ composite can better guarantee the safety of the wood processing production process. Moreover, the reasons for performance advantages of the NH₄H₂PO₄/Mg(OH)₂ composite were discussed.     

Suppression of metal dust deflagrations

Dust explosions continue to pose a serious threat to the process industries handling combustible powders. According to a review carried out by the Chemical Safety Board (CSB) in 2006, 281 dust explosions were reported between 1980 and 2005 in the USA, killing 119 workers and injuring 718. Metal dusts were involved in 20% of these incidents. Metal dust deflagrations have also been regularly reported in Europe, China and Japan.The term “metal dusts” encompasses a large family of materials with diverse ignitability and explosibility properties. Compared to organic fuels, metal dusts such as aluminum or magnesium exhibit higher flame temperature (T_f), maximum explosion pressure (P_max), deflagration index (K_St), and flame speed (S_f), making mitigation more challenging. However, technological advances have increased the efficiency of active explosion protection systems drastically, so the mitigation of metal dust deflagrations has now become possible.This paper provides an overview of metal dust deflagration suppression tests. Recent experiments performed in a 4.4 m³ vessel have shown that aluminum dust deflagrations can be effectively suppressed at a large scale. It further demonstrates that metal dust deflagrations can be managed safely if the hazard is well understood.     

超细CaCO3惰化剂对铝合金抛光伴生粉尘爆炸的防控效果*

为探究超细粉体惰化剂对铝合金抛光伴生粉尘爆炸特性的影响规律,利用标准化实验装置及自行搭建的实验平台,在对爆炸基本参数进行测试的基础上,分别研究超细CaCO3粉体对抛光废弃物粉尘点燃敏感度的钝化作用以及对爆炸火焰传播进程的惰化效果,并在相同条件下与同等粒径高纯度铝粉的实验效果进行比对。研究结果表明:铝合金抛光废弃物粉尘最小点火能量为280 mJ,而同等粒径高纯度铝粉最小点火能量为35 mJ;在铝合金抛光废弃物粉尘质量浓度为300 g/m3条件下,发生爆炸的火焰传播速度峰值为7.4 m/s,约为高纯度铝粉的57%,铝合金抛光废弃物粉尘的爆炸敏感度及猛烈度均低于高纯度铝粉;当超细CaCO3粉体的惰化比为30%时,可将铝合金抛光废弃物粉尘的最小点火能量钝化至约1 J,爆炸火焰失去持续传播能力,惰化作用效果充分显现。     

Experimental study on CO2/CF3I suppression of methane-air explosion and flame propagation

To explore the inhibitory effects of CF₃I and CO₂ gas on the explosion pressure and flame propagation characteristics of 9.5% methane, a spherical 20 L experimental explosion device was used to study the effect of the gas explosion suppressants on the maximum explosion pressure, maximum explosion pressure rise rate and flame propagation speed of methane. The results indicated that with a gradual increase in the volume fraction of the gas explosion suppressant, the maximum explosion pressure of methane and maximum explosion pressure rise rate gradually decreased, and the time taken to reach the maximum explosion pressure and maximum explosion pressure rise rate was gradually delayed. At the same time, the flame propagation speed gradually decreased. Additionally, the time taken for the flame to reach the edge of the window and the time taken for a crack as well as a cellular structure to appear on the flame surface was gradually delayed. The fluid dynamics uncertainty was suppressed. The explosion pressure and flame propagation processes were markedly suppressed, but the flame buoyancy instability was gradually enhanced. By comparing the effects of the two gas explosion suppressants on the pressure and flame propagation characteristics, it was found that at the same volume fraction, trifluoroiodomethane was significantly better than carbon dioxide in suppressing the explosion of methane. By comparing the reduction rates of the characteristic methane explosion parameters at a volume fraction of 9.5%, it was observed that the inhibitory effect of 4% trifluoroiodomethane on the maximum explosion pressure was approximately 4.6 times that of the same amount of carbon dioxide, and the inhibitory effect of 4% trifluoroiodomethane on the maximum explosion pressure rise rate and flame propagation speed was approximately 2.7 times that of the same amount of carbon dioxide. The addition of 0.5%–1.5% trifluoromethane to 4% and 8% carbon dioxide can improve the explosion suppression efficiency of carbon dioxide. This enhancing phenomenon is a comprehensive manifestation of the oxygen-decreasing effect of carbon dioxide and the trifluoroiodomethane-related endothermic effect and reduction in key free radicals.     

Law of variation for low density polyethylene dust explosion with different inert gases

To reveal the effects of different inert gases on explosion characteristics during low density polyethylene (LDPE) dust explosion and optimize the explosion-proof process, eight N₂ (CO₂)/air mixed inerting conditions were experimentally studied. Typical inerting conditions with 12 L cylindrical explosive tank were used to study the characteristics on the flame propagation. The thermogravimetric analysis with related theories were used to further explain the mechanism and quantities in low density polyethylene (LDPE) dust explosion with different inert gases. The results showed that the reduction of O₂ concentration could effectively delay the progress of flame growth process and weaken the effect of dust combustion reaction. The flame growth process of condition (N₂/air (18% O₂)) was 2.05 times slower than that of the non-inert condition. The explosion strength was obviously reduced, and the characteristic parameters such as explosion pressure and flame propagation speed were also affected by the decrease of O₂ concentration. For LDPE powder, the smaller the median diameter, the greater the explosion intensity and the lower the limiting oxygen content (LOC). The LOC with CO₂ was usually higher than that with N₂ and the effect of CO₂ was significantly better than N₂ in inerting.     

Suppression effects of ammonium dihydrogen phosphate dry powder and melamine pyrophosphate powder on an aluminium dust cloud explosion

Selecting a suitable flame-retardant powder is essential for preventing or reducing the risk of aluminium dust cloud explosions. Two types of retardant materials were studied, namely ABC powder (a flame-retardant powder mainly composed of ammonium dihydrogen phosphate dry powder) and melamine pyrophosphate powder (MPP). A specially designed rectangular pipe was used to examine the influences and mass fractions of the aforementioned flame retardants and the effects of compounds on maximum explosion pressure and maximum explosion pressure rate of increase. The results showed that the explosion-suppression effects of MPP powder were superior to those of ABC powder. Furthermore, the suppression effects of combining ABC and MPP to form compounds in various ratios were explored. The explosion-suppression effects of the single flame-retardant powders and flame-retardant powder compound were compared, which revealed that the effects of the flame-retardant compound were intermediate to those of ABC and MPP used separately. No synergistic effect was observed in the compound retardant. However, component mass fractions influenced the retardant properties of the compound. The suppression mechanism was investigated through thermal analysis, which revealed that the decomposition of the two flame-retardant powders was an endothermic process that generated inert gas. The addition of flame-retardant powder delayed the time required by aluminium to break through its oxide film. However, the thermal analysis curve of the compound overlapped those of the two single powders, and no new chemical reaction occurred. Thus, no change was observed in the efficacy of the flame-retardant properties.     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

Inerting effect of N2 on explosion of LDPE dust/ethylene hybrid mixtures

Explosion flame propagation characteristics and overpressure distribution of low density polyethylene (LDPE) dust and ethylene hybrid mixture were investigated under N₂ inerting conditions using a custom-designed 12 L cylindrical explosion tank. The results showed that a small amount of ethylene could promote the explosion characteristics of LDPE dust. N₂ inerting had different inhibitory effects on the explosion flame of LDPE dust and its mixture with ethylene. The explosion overpressure strength of the LDPE dust/ethylene hybrid mixture decreased with increasing N₂ concentration. The overall suppression effect of N₂ on the explosion overpressure of the LDPE dust was better than that of the LDPE dust/ethylene hybrid mixture explosion. As the ethylene concentration increased from 0% to 2.5%, the limiting oxygen concentration decreased by 13% oxygen. This small amount of ethylene restricted the traditional inerting process. The study conclusions can provide further scientific basis for the inerting and explosion proofing design of production process equipment involving LDPE dust.     

Inhibiting effects of gas–particle mixtures containing CO2, Mg(OH)2 particles,and NH4H2PO4 particles on methane explosion in a 20-L closed vessel

The main risk factors from methane explosion are the associated shock waves, flames, and harmful gases. Inert gases and inhibiting powders are commonly used to prevent and mitigate the damage caused by an explosion. In this study, three inhibitors (inert gas with 8.0 vol% CO₂, 0.25 g/L Mg(OH)₂ particles, and 0.25 g/L NH₄H₂PO₄ particles) were prepared. Their inhibiting effects on methane explosions with various concentrations of methane were tested in a nearly spherical 20-L explosion vessel. Both single-component inhibitors and gas–particle mixtures can substantially suppress methane explosions with varying degrees of success. However, various inhibitors exhibited distinct reaction mechanisms for methane gas, which indicated that their inhibiting effects for methane explosion varied. To alleviate amplitude, the ranking of single-component inhibitors for both explosion pressure (P_ex) and the rate of explosion pressure rise [(dP/dt)_ex] was as follows: CO₂, NH₄H₂PO₄ particles, and Mg(OH)₂ particles. In order of decreasing amplitude, the ranking of gas‒particle mixtures for both P_ex and (dP/dt)_ex was as follows: CO₂–NH₄H₂PO₄ mixture, CO₂‒Mg(OH)₂ mixture, and pure CO₂. Overall, the optimal suppression effect was observed in the system with the CO₂–NH₄H₂PO₄ mixture, which exhibited an eminent synergistic effect on methane explosions. The amplitudes of P_ex with methane concentrations of 7.0, 9.5, and 11.0 vol% decreased by 37.1%, 42.5%, and 98.6%, respectively, when using the CO₂–NH₄H₂PO₄ mixture. In addition, an antagonistic effect was observed with CO₂‒Mg(OH)₂ mixtures because MgO, which was generated by the thermal decomposition of Mg(OH)₂, can chemically react with water vapor and CO₂ to produce basic magnesium carbonate (xMgCO₃·yMg(OH)₂·zH₂O), thereby reducing the CO₂ concentration in a reaction system. This research revealed the inhibiting effects of gas‒particle mixtures (including CO₂, Mg(OH)₂ particles, and NH₄H₂PO₄ particles) on methane explosions and provided primary experimental data.     

Synergistic suppression effects of flame retardant,porous minerals and nitrogen on premixed methane/air explosion

A novel composite inhibitor based on porous mineral materials and conventional flame retardant of ammonium polyphosphate (APP) is prepared to suppress the premixed methane/air explosion. Taking advantages of gas and powder inhibitor, N₂ and the prepared composite inhibitor are combined to use. The suppression performance of N₂-composite inhibitor on methane explosion is investigated on a 20-L spherical experimental explosion apparatus and the characteristic pressure data are obtained. The combined inhibition effects of N₂ and the prepared composite inhibitor are greater than either acting alone. Thermal decomposition behavior and gaseous products of composite inhibitor are analyzed with thermogravimetric analysis and thermogravimetric-mass spectrometry, respectively. Based on physical and chemical actions, the inhibition mechanisms of N₂-composite inhibitor system are proposed. This work provides a reference to prepare high-performance gas explosion inhibitor based on the synergism of binary or multiple components.     

Hybrid H2/Al dust explosions in Siwek sphere

Explosion indices and explosion behaviour of Al dust/H₂/air mixtures were studied using standard 20 l sphere. The study was motivated by an explosion hazard occurring at some accidental scenarios considered now in ITER design (International Thermonuclear Experimental Reactor). During Loss-of-Vacuum or Loss-of-Coolant Accidents (LOCA/LOVA) it is possible to form inside the ITER vacuum vessel an explosible atmosphere containing fine Be or W dusts and hydrogen. To approach the Be/H₂ explosion problem, Be dust is substituted in this study by aluminium, because of high toxicity of Be dusts. The tested dust concentrations were 100, 200, 400, 800, and 1200 g/m3; hydrogen concentrations varied from 8 to 20 vol. % with 2% step. The mixtures were ignited by a weak electric spark. Pressure evolutions were recorded during the mixture explosions. In addition, the gaseous compositions of the combustion products were measured by a quadruple mass-spectrometer. The dust was involved in the explosion process at all hydrogen and dust concentrations even at the combination ‘8%/100 g/m3’. In all the other tests the explosion overpressures and the pressure rise rates were noticeably higher than those relevant to pure H₂/air mixtures and pure Al dust/air mixtures. At lower hybrid fuel concentrations the mixture exploded in two steps: first hydrogen explosion followed by a clearly separated Al dust explosion. With rising concentrations, the two-phase explosion regime transits to a single-phase regime where the two fuel components exploded together as a single fuel. In this regime both the hybrid explosion pressures and pressure rise rates are higher than either H₂ or Al ones. The two fuels compete for the oxygen; the higher the dust concentration, the more part of O2 it consumes (and the more H₂ remains in the combustion products). The test results are used to support DUST3D CFD code developed at KIT to model LOCA or LOVA scenarios in ITER.     

Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

Combustion characteristics of pure aluminum and aluminum alloys powders

In this work, the explosion and combustion characteristics of aluminum and some aluminum alloys AlSi7Mg0.6, AlSi10Mg, AlMg5 under powders conditioning were studied. The idea was to compare the combustion of pure aluminum and aluminum alloys. The Minimum Ignition Energy (MIE) and explosion severity ΔP_max and (dP/dt)_max which represents the dust explosion parameters were measured for all powders using Hartman tube and 20 L spherical bomb. The particles temperature and flame temperature were determined by using IR pyrometer and spectroscopy respectively. The results showed that pure aluminum was more sensitive and severe than its alloys. MIE were: 4 mJ for pure aluminum, 13–23 mJ for aluminum alloys. For severity parameters, the overpressure ΔP_max were around 7–8 bars with maximum rate of pressure rise at 1170 bar/s for aluminum and 5–7 bars with 250–360 bar/s for alloys. However, it has been observed that flame temperatures were similar for aluminum and alloys and vary around 2800–3300 K as a function of concentration.     

Consequence prediction for dust explosions involving interconnected vessels using computational fluid dynamics modeling

Combustible dust explosions continue to present a significant threat toward operating personnel and pneumatic conveyance equipment in a wide variety of processing industries. Following ignition of suspended fuel within a primary enclosure volume, propagation of flame and pressure fronts toward upstream or downstream interconnected enclosures can result in devastating secondary explosions if not impeded through an appropriate isolation mechanism. In such occurrences, an accelerated flame front may result in flame jet ignition within the secondary vessel, greatly increasing the overall explosion severity. Unlike an isolated deflagration event with quantifiable reduced pressures (vent sizing according to NFPA 68 guidance), oscillation of pressure between primary and secondary process vessels leads to uncertain overpressure effects. Dependent on details of the application such as relative enclosure volumes, relief area, fuel type, suspended concentration, duct size, and duct length, the maximum system pressure in both interconnected vessels can be unpredictable. This study proposes the use of FLame ACceleration Simulator (FLACS) computational fluid dynamics (CFD) modeling to provide reliable consequence predictions for specific case scenarios of dust deflagrations involving interconnected equipment. Required minimum supplement to the originally calculated relief area (A_v) was determined through iterative simulation, allowing for reduced explosion pressures (P_red) to be maintained below theoretical enclosure design strengths (P_es).     

Study on the preparation of novel NiB/Hβ-Al2O3 micro-mesoporous suppressant and its inhibition mechanism of coal dust explosion flame

Coal dust explosion is one of the serious accidents in the coal industry. It is of great significance to study the flame suppression of coal dust explosions. In this paper, a novel active component NiB with amorphous structure for explosion suppression was synthesized by the chemical reduction method. Furthermore, the novel explosion suppressant NiB/Hβ-Al₂O₃ was prepared through the kneading method by loading novel amorphous NiB nanoparticles on Hβ-Al₂O₃ with the micro-mesoporous structure as the carrier. The morphology and structure of NiB/Hβ-Al₂O₃ were characterized by XRD, BET, SEM, and FTIR, which showed that the NiB/Hβ-Al₂O₃ has proper pore structure and NiB nanoparticles are uniformly distributed as active components for explosion suppression in suppressant. Hartmann tube was used to evaluate the inhibition of coal dust deflagration. The results showed that the flame propagation distance and velocity decreased with the increase of the explosion suppressant. When the addition of explosion suppressant was 30 wt%, the explosion of coal dust was suppressed effectively. Furthermore, combing with the analysis results of the products after coal dust deflagration, the physical and chemical inhibition mechanism of the novel NiB/Hβ-Al₂O₃ explosion suppressant on coal dust deflagration was put forward.