Explosibility of hydrogen–graphite dust hybrid mixtures

To evaluate the hazard of combined hydrogen/dust explosions under severe accident conditions in International Thermonuclear Experimental Reactor (ITER), standard method of 20-L-sphere was used to measure the explosion indices of 4-μm fine graphite dust in lean hydrogen/air mixtures. The mixtures were ignited by a weak electric spark. The tested fuel concentrations were 8–18 vol% H₂ and 25–250 g/m³ dust. If the hydrogen content is higher than 10 vol%, the dust constituent can be induced to explode by the hydrogen explosion initiated by a weak electric spark. Depending on the fuel component concentrations, the explosions proceed in either one or two stages. In two-stage explosions occurring at low hydrogen and dust concentrations, the mixture ignition initiates first a fast hydrogen explosion followed by a slower phase of the dust explosion. With increasing dust concentration, the dust explodes faster and can overlap the hydrogen-explosion stage. At higher hydrogen concentrations, the hybrid mixtures explode in one stage, with hydrogen and dust reacting at the same time scale. Maximum overpressures of hybrid explosions are higher than those observed with hydrogen alone; maximum rates of pressure rise are lower in two-phase explosions and, generally, higher in one-stage explosions, than those characteristic of the corresponding H₂/air mixtures.     

Experimental investigation of the complex deflagration phenomena of hybrid mixtures of activated carbon dust/hydrogen/air

This paper aims to develop quantitative insights based on measured deflagration parameters of hybrid mixtures of activated carbon (AC) dust and hydrogen (H₂) gas in air. The generated experimental evidence is used to reject the claim of the null hypothesis (H₀) that severity of deflagrations of H₂/air mixtures always bound the severity of deflagrations of heterogenous combustible mixtures of AC dust/H₂/air containing the same H₂ concentrations as in the H₂/air binaries. The core insights of this investigation show that the maximum deflagration pressure rise (ΔP_MAX) and maximum rate of pressure rise ((dP/dt)_MAX) of this hybrid mixture are greater than those corresponding to deflagrations of H₂/air mixtures for all the dust and H₂ concentrations being examined. The deflagration severity indices (K_St and ES) of the hybrid mixture containing 29 mol% H₂ are found to be greater than those of the H₂/air mixture containing 29 mol% H₂. Also, the minimum explosible concentration (MEC) of the hybrid mixture is lower than that of the AC dust in air only. The insights gained should lead to better realization of the severity of a postulated safety-significant accident scenario associated with on-board cryoadsorption H₂ storage systems for fuel-cell (FC) powered light-duty vehicles. The identified insights could also be relevant to other industrial processes where combustible dusts are generated in the vicinity of solvent vapors. Moreover, these insights should be useful for supporting quantitative risk assessment (QRA) of on-board H₂ storage systems, designing improved safety measures for cryoadsorption H₂ storage tanks, and guiding H₂ safety standards and transportation regulations.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

工业粉尘“二次爆炸”过程研究

开展了工业粉尘“二次爆炸”过程实验室研究工作。对玉米淀粉、小麦粉等粮食粉尘进行了研究，得到了“二次爆炸”发展过程以及最后形成的爆轰波特性，还进一步研究了粉尘层冲击波卷扬过程和分析讨论了粉尘“二次爆炸”过程的影响因素。     

EVA树脂粉尘/甲烷/空气杂混物爆炸特性

在20 L爆炸实验装置中,开展了3种不同中值粒径的EVA树脂粉尘/甲烷/空气所组成的杂混物爆炸特性研究,探究了甲烷浓度对粉尘爆炸下限、最大爆炸压力的影响。结果表明,尽管添加的甲烷气体浓度低于爆炸下限,仍使得粉尘爆炸下限得以降低,粒径较大的EVA III粉尘,当甲烷体积分数为1%时,爆炸下限降低约25%;粒径较小的EVA I粉尘,当混入甲烷体积分数为4%时,爆炸下限则降低80%;甲烷体积分数每增加1%,可燃粉尘最大爆炸压力上升约10%,但对于粒径较小的EVA I粉尘,当甲烷体积分数为4%时,最大爆炸压力的上升呈现突变趋势,上升近50%。     

Explosibility of fine graphite and tungsten dusts and their mixtures

To evaluate the explosion hazard of ITER-relevant dusts, a standard method of 20-l-sphere was used to measure the explosion indices of fine graphite and tungsten dusts and their mixtures. The effect of dust particle size was studied on the maximum overpressures, maximum rates of pressure rise, and lower explosive concentrations of graphite dusts in the range 4 μm to 45 μm. The explosion indices of 1 μm tungsten dust and its mixtures with 4 μm graphite dust were measured. The explosibility of these dusts and mixtures were evaluated. The dusts tested were ranked as St1 class. Dust particle size was shown to be very important for explosion properties. The finest graphite dust appeared to have the lowest minimum explosion concentration and be able to explode with 2 kJ ignition energy.     

PAN dust explosion inhibition mechanisms of NaHCO3 and Al(OH)3

We investigate the PAN dust explosion inhibition behaviors of NaHCO₃ and Al(OH)₃ in a 20 L spherical explosion system and a transparent pipe explosion propagation test system. The results show that, in the standard 20 L spherical explosion system, the highest PAN dust explosion concentration is 500 g/m³, the maximum explosion pressure is 0.661 MPa, and the maximum explosion pressure increase rate is 31.64 MPa/s; adding 50% NaHCO₃ and 60% Al(OH)₃ can totally inhibit PAN dust explosion. In the DN0.15 m transparent pipe explosion propagation test system, for 500 g/m³ PAN dust, the initial explosion flame velocity is 102 m/s, the initial pressure is 0.46 MPa, and the initial temperature is 967 °C; adding 60% NaHCO₃ and 70% Al(OH)₃ can totally inhibit PAN dust explosion flames. Through FTIR and TG analyses, we obtain the explosion products and pyrolysis patterns of the explosion products of PAN dust, NaHCO₃, and Al(OH)₃. On this basis, we also summarize the PAN dust explosion inhibition mechanisms of NaHCO₃ and Al(OH)₃.     

Scaling of dust explosion violence from laboratory scale to full industrial scale – A challenging case history from the past

The standardized K_St parameter still seems to be widely used as a universal criterion for ranking explosion violence to be expected from various dusts in given industrial situations. However, this may not be a generally valid approach. In the case of dust explosion venting, the maximum pressure P_max generated in a given vented industrial enclosure is not only influenced by inherent dust parameters (dust chemistry including moisture, and sizes and shapes of individual dust particles). Process-related parameters (degree of dust dispersion, cloud turbulence, and dust concentration) also play key roles. This view seems to be confirmed by some results from a series of large scale vented dust explosion experiments in a 500 m³ silo conducted in Norway by CMI, (now GexCon AS) during 1980–1982. Therefore, these results have been brought forward again in the present paper. The original purpose of the 500 m³ silo experiments was to obtain correlations between P_max in the vented silo and the vent area in the silo top surface, for two different dusts, viz. a wheat grain dust collected in a Norwegian grain import silo facility, and a soya meal used for production of fish farming food. Both dusts were tested in the standard 20-L-sphere in two independent laboratories, and also in the Hartmann bomb in two independent laboratories. P_max and (dP/dt)_max were significantly lower for the soya meal than for the wheat grain dust in all laboratory tests. Because the available amount of wheat grain dust was much larger than the quite limited amount of available soya meal, a complete series of 16 vented silo experiments was first performed with the wheat grain dust, starting with the largest vent area and ending with the smallest one. Then, to avoid unnecessary laborious changes of vent areas, the first experiment with soya dust was performed with the smallest area. The dust cloud in the silo was produced in exactly the same way as with the wheat grain dust. However, contrary to expectations based on the laboratory-scale tests, the soya meal exploded more violently in the large silo than the wheat grain dust, and the silo was blown apart in the very first experiment with this material. The probable reason is that the two dusts responded differently to the dust cloud formation process in the silo on the one hand and in the laboratory-scale apparatuses on the other. This re-confirms that a differentiated philosophy for design of dust explosion vents is indeed needed. Appropriate attention must be paid to the influence of the actual dust cloud generation process on the required vent area. The location and type of the ignition source also play important roles. It may seem that tailored design has to become the future solution for tackling this complex reality, not least for large storage silos. It is the view of the present author that the ongoing development of CFD-based computer codes offers the most promising line of attack. This also applies to design of systems for dust explosion isolation and suppression.     

Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

Explosion of lycopodium-nicotinic acid–methane complex hybrid mixtures

With the terms “complex hybrid mixtures”, we mean mixtures made of two or more combustible dusts mixed with flammable gas or vapors in air (or another comburent).In this work, the flammability and explosion behavior of selected complex hybrid mixtures was studied. In particular, we investigated mixtures of nicotinic acid, lycopodium and methane. We performed explosion tests in the 20-L explosion vessel at different overall (nicotinic plus lycopodium) dust concentrations, nicotinic acid/lycopodium ratios, and methane concentrations.An exceptional behavior (in terms of unexpected values of rate of pressure rise and pressure) was found for the complex hybrid mixtures containing lycopodium and nicotinic acid in equal amounts. This mixture was found to be much more reactive than all the other dust mixtures, whatever the dust concentration and the methane content.     

Effects of ignition energy on fire and explosion characteristics of dilute hybrid fuel in ventilation air methane

Deflagration explosions of coal dust clouds and flammable gases are a major safety concern in coal mining industry. Accidental fire and explosion caused by coal dust cloud can impose substantial losses and damages to people and properties in underground coal mines. Hybrid mixtures of methane and coal dust have the potential to reduce the minimum activation energy of a combustion reaction. In this study the Minimum Explosion Concentration (MEC), Over Pressure Rise (OPR), deflagration index for gas and dust hybrid mixtures (K_st) and explosive region of hybrid fuel mixtures present in Ventilation Air Methane (VAM) were investigated. Experiments were carried out according to the ASTM E1226-12 guideline utilising a 20 L spherical shape apparatus specifically designed for this purpose.Resultsobtained from this study have shown that the presence of methane significantly affects explosion characteristics of coal dust clouds. Dilute concentrations of methane, 0.75–1.25%, resulted in coal dust clouds OPR increasing from 0.3 bar to 2.2 bar and boosting the K_st value from 10 bar m s⁻¹ to 25 bar m s⁻¹. The explosion characteristics were also affected by the ignitors’ energy; for instance, for a coal dust cloud concentration of 50 g m⁻³ the OPR recorded was 0.09 bar when a 1 kJ chemical ignitor was used, while, 0.75 bar (OPR) was recorded when a 10 kJ chemical ignitor was used.For the first time, new explosion regions were identified for diluted methane-coal dust cloud mixtures when using 1, 5 and 10 kJ ignitors. Finally, the Le-Chatelier mixing rule was modified to predict the lower explosion limit of methane-coal dust cloud hybrid mixtures considering the energy of the ignitors.     

Effect of ignition delay on explosion parameters of corn dust/air in confined chamber

This paper presents the explosion parameters of corn dust/air mixtures in confined chamber. The measurements were conducted in a setup which comprises a 5 L explosion chamber, a dust dispersion sub-system, and a transient pressure measurement sub-system. The influences of the ignition delay on the pressure and the rate of pressure rise for the dust/air explosion have been discussed based on the experimental data. It is found that at the lower concentrations, the explosion pressure and the rate of pressure rise of corn dust/air mixtures decrease as the ignition delay increases from 60 ms; But at the higher concentrations, the explosion pressure and the rate of pressure rise increase slightly as the ignition delay increases from 60 ms to 80 ms, and decrease beyond 80 ms. The maximum explosion pressure of corn dust/air mixtures reaches its highest value equal to 0.79 MPa at the concentration of 1000 gm⁻³.     

Medium-scale experiments on vented hydrogen deflagration

A series of medium-scale experiments on vented hydrogen deflagration was carried out at the KIT test side in a chamber of 1 × 1 × 1 m³ size with different vent areas. The experimental program was divided in three series: (1) uniform hydrogen–air mixtures; (2) stratified hydrogen–air mixtures within the enclosure; (3) a layer deflagration of uniform mixture. Different uniform hydrogen–air mixtures from 7 to 18% hydrogen were tested with variable vent areas 0.01–1.0 m². One test was done for rich mixture with 50% H₂. To vary a gradient of concentration, all the experiments with a stratified hydrogen–air mixtures had about 4%H₂ at the bottom and 10 to 25% H₂ at the top of the enclosure. Measurement system consisted of a set of pressure sensors and thermocouples inside and outside the enclosure. Four cameras combined with a schlieren system (BOS) for visual observation of combustion process through transparent sidewalls were used. Four experiments were selected as benchmark experiments to compare them with four times larger scale FM Global tests (Bauwens et al., 2011) and to provide experimental data for further CFD modelling. The nature of external explosion leading to the multiple pressure peak structure was investigated in details. Current work addresses knowledge gaps regarding indoor hydrogen accumulations and vented deflagrations. The experiments carried out within this work attend to contribute the data for improved criteria for hydrogen–air mixture and enclosure parameters to avoid unacceptable explosion overpressure. Based on theoretical analysis and current experimental data a further vent sizing technology for hydrogen deflagrations in confined spaces should be developed, taking into account the peculiarities of hydrogen–air mixture deflagrations in presence of obstacles, concentration gradients of hydrogen–air mixtures, dimensions of a layer of flammable cloud, vent inertia, etc.     

锌粉燃爆事故分析与预防

本文以一起锌粉爆炸事故为例,叙述锌粉爆炸事故的发生过程,探究爆炸事故发生的直接原因和间接原因,应用Semenov热自燃理论揭示了本次事故发生规律。结合事故原因分析,考虑防止除尘器积尘及控制二次扬爆,研究设计了新型除尘器,经计算管道中最低风速要求16.3m/s,喷锌间内的风速0.25~0.5m/s,可有效减少粉尘积聚,风管设计中拆除原除尘器中采用的挡板,减少弯管的使用,可避免风管积尘。新型除尘器自动化性能高,可降低由于积尘、超温引发粉尘爆炸事故的概率,对减少人员伤亡和降低经济损失有重要意义,现已投入生产运行,具有一定的工程应用价值和推广价值。     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

Explosion parameters of wood chip-derived syngas in air

The wood gasification process poses serious concerns about the risk of explosion. The design of prevention and mitigation measures requires the knowledge of safety parameters, such as the maximum explosion pressure, the maximum rate of pressure rise and the gas deflagration index, K_G, at standard ambient temperature (25 °C) and pressure (1 bar) conditions. However, the analysis at specific process conditions is strongly recommended, as the explosion behavior of gas mixtures may be completely different.In the work presented in this paper, the explosion behavior of mixtures with composition representative of wood chip-derived syngas (CO/H₂/CH₄/CO₂/N₂ mixtures with and without H₂O) was experimentally studied in a closed combustion chamber. Experiments were run at two temperatures, 300 °C and 10 °C, and at atmospheric pressure. Test conditions were requested by the safety engineering designer of an existing industrial-scale wood gasification plant. In order to identify the specific fuel–air ratios to be analyzed, thus reducing the number of experimental tests, a preliminary thermo-kinetic study was performed.Results have shown that the mixtures investigated can be classified as low-reactivity mixtures, the higher value of K_G found (∼36 bar m/s) being much lower than the K_G value of methane (55 bar m/s @ 25 °C).     

Study on the preparation of novel NiB/Hβ-Al2O3 micro-mesoporous suppressant and its inhibition mechanism of coal dust explosion flame

Coal dust explosion is one of the serious accidents in the coal industry. It is of great significance to study the flame suppression of coal dust explosions. In this paper, a novel active component NiB with amorphous structure for explosion suppression was synthesized by the chemical reduction method. Furthermore, the novel explosion suppressant NiB/Hβ-Al₂O₃ was prepared through the kneading method by loading novel amorphous NiB nanoparticles on Hβ-Al₂O₃ with the micro-mesoporous structure as the carrier. The morphology and structure of NiB/Hβ-Al₂O₃ were characterized by XRD, BET, SEM, and FTIR, which showed that the NiB/Hβ-Al₂O₃ has proper pore structure and NiB nanoparticles are uniformly distributed as active components for explosion suppression in suppressant. Hartmann tube was used to evaluate the inhibition of coal dust deflagration. The results showed that the flame propagation distance and velocity decreased with the increase of the explosion suppressant. When the addition of explosion suppressant was 30 wt%, the explosion of coal dust was suppressed effectively. Furthermore, combing with the analysis results of the products after coal dust deflagration, the physical and chemical inhibition mechanism of the novel NiB/Hβ-Al₂O₃ explosion suppressant on coal dust deflagration was put forward.     

Lower explosion limit of hybrid mixtures of burnable gas and dust

Hybrid mixtures – mixtures of burnable dusts and burnable gases – pose special problems to industries, as their combined Lower Explosion Limit (LEL) can lie below the LEL of the single substances. Different mathematical relations have been proposed by various authors in literature to predict the Lower Explosion Limit of hybrid mixtures (LEL_hybrid). The aim of this work is to prove the validity or limitations of these formulas for various combinations of dusts and gases. The experiments were executed in a standard 20 L vessel apparatus used for dust explosion testing. Permanent spark with an ignition energy of 10 J was used as ignition source. The results obtained so far show that, there are some combinations of dust and gas where the proposed mathematical formulas to predict the lower explosible limits of hybrid mixtures are not safe enough.     

Experimental determination of dust cloud combustion parameters of α-AlH3 powder in its charged and fully discharged states for H2 storage applications

This study discusses results of an experimental program for determination of dust cloud combustion parameters of charged and fully discharged states of metastable alane (aluminum hydride, α-AlH₃ polymorph) powder in air. The measured characterization parameters include: maximum deflagration pressure rise (ΔP_MAX), maximum rate of pressure rise (dP/dt)_MAX, minimum ignition temperature (T_C), minimum explosible concentration (MEC), and minimum ignition energy (MIE). These measured values are used for calculating the associated explosion severity (ES) index, and volume-normalized maximum rate of pressure rise (K_St). The experimental results show values of MEC and T_C of fully discharged alane to be greater than those of the charged alane but measured MIE values are about the same. Moreover, the results show higher reactivity of fully discharged alane dust cloud in air compared to its charged state. For example, ES and K_St of discharged alane dust cloud in air are about 300% and 35% greater, respectively, than ES and K_St of charged alane dust. The higher air reactivity of fully-discharged (primarily Al powder) dust cloud compared to its charged state can be attributed to the higher surface energy (J/m²) of Al compared to that of α-AlH₃. These experimental insights have safety implications in postulated risk scenarios involving light-duty vehicles powered by PEM fuel cells. The core insights and critical data provided by this contribution are useful for supporting development and promulgation of hydrogen safety standards and augmenting property databases of hydrogen storage materials.     

Comparative study of explosion processes controlled by homogeneous and heterogeneous combustion mechanisms

The dust explosion behaviors induced by two different combustion mechanisms (homogeneous and heterogeneous mechanisms) were comparatively investigated, based on the experiments under different dust concentrations, particle sizes and initial pressures in Siwek 20-L chamber. Based on the thermo-gravimetric analysis (TGA), sweet potato dust and magnesium dust were selected as the representative dusts with homogeneous and heterogeneous combustion mechanisms, respectively. Experiments find that these two dusts have different behaviors in the explosion kinetics due to different combustion mechanisms. For sweet potato dust, the explosion pressure p_max, the pressure rise rate (dp/dt)_max and the combustion fraction η exhibit similar variation trends as dust concentration increases and they all reach to the maximum values at the worst-case concentration; while for magnesium dust, the variation of (dp/dt)_max is somewhat different from that of p_max, that is, the (dp/dt)_max will achieve the maximum at the concentration higher than the worst-case and keep stabilized with further increase of dust concentration. As the particle size decreases, the (dp/dt)_max for sweet potato dust will increasingly rise and gradually approach to a stabilized value, but for magnesium dust, the increase of (dp/dt)_max becomes pronounced only in the range of smaller particle sizes. To account the effect of initial pressure on p_max under different combustion mechanisms, a dimensionless pressure P_R was introduced to denote the relative intensity of explosion. It is found that, for sweet potato dust, the increased initial pressure will promote the explosion process (or with high P_R) for the dust cloud with high concentration due to the augmented oxygen concentration, but for the dust cloud with low concentration, the increased initial pressure will suppress the explosion process due to the increased resistance in devolatilization. For magnesium dust, the rise of initial pressure will generally promote the explosion process even for the dust cloud with low concentration; however, in the case of small particle size, the promotion of increased initial pressure to the explosion process is not so pronounced.