Optimization of novel pyrazolium ionic liquid catalysts for transesterification of bitter apple oil

In the present study, 4 different functionalized pyrazoliums based on sulfoalkyl-pyrazolium hydrogensulfate and alkylsulfo-alakylpyrazolium hydrogensulfate were explored to catalyze biodiesel production from bitter apple oil (BAO). The results demonstrated that a longer chains catalyst of 2-(4-sulfobutyl) pyrazolium hydrogensulfate (SBPHSO₄) exhibited the highest catalytic activity, which is attributed to its strong acidity. The highest yield of esters was up to 89.5% when the reaction was carried out under the conditions of 5.2 wt% of SBPHSO₄, molar ratio of methanol to BAO of 15:1, 170 °C, and 800 rpm for 6 h. These results demonstrated that ionic liquids offer a promising new type of pyrazolium catalyst for biodiesel production. The use of clean ionic liquids in preparing clean biodiesel could solve the drawbacks associated with using the old conventional catalysts and might be employed as an efficient catalyst for such relevance.     

Synthesis of Bio-Diesel and Bio-Lubricant by Transesterification of Vegetable Oil with Lower and Higher Alcohols Over Heteropolyacids Supported by Clay (K-10)

The use of different lower and higher alcohols viz; methanol, ethanol, n-propanol and n-octanol, for the synthesis of methyl, ethyl, propyl and octyl fatty acid esters by transesterification of vegetable oil (triglycerides) with respective alcohols also known as ‘Bio-diesel’ and ‘Bio-lubricants’ was studied in detail. The reactions were carried out in a batch process. The activity with different supports like clay (K-10), activated carbon, ZSM-5, H-beta and TS-1 were compared. The superacids (heteropolyacids, HPA) viz; Dodeca-Tungstophosphoric acid [H₃PO₄·12 WO₃·xH₂O] (TPA) and Dodeca-Molybdo phosphoric acid ammonium salt hydrate [H₁₂Mo₁₂N_3-O₄₀P + aq] (DMAA) was used to increase the acidity and so the activity by loading on the most active support viz; clay (K-10). These HPA loaded on clay as a catalyst was used for the following study: effect of percent HPA loading on clay, effect of different vegetable oils, effect of different alcohols on the triglyceride conversion based on glycerol formation and selectivity based on alkyl esters formation. The data is compared at the best-optimized identical set of operating reaction conditions: 170 °C, 170 rpm, catalyst loading: 5% (w/w of reaction mixture), molar ratio (oil: alcohol): 1:15 and time on stream of 8 h. The generated data is also evaluated based on the reported one.     

Refinery wastewater degradation with titanium dioxide,zinc oxide,and hydrogen peroxide in a photocatalytic reactor

This paper presents the photo-catalytic degradation of real refinery wastewater from National Refinery Limited (NRL) in Karachi, Pakistan, using TiO₂, ZnO, and H₂O₂. The pretreatment of the refinery effluent was carried out on site and pretreated samples were tested at 32–37 °C in a stirrer bath reactor by using ultra-violet photo oxidation process. The degradation of wastewater was measured as a change in initial chemical oxygen demand (COD) and with time. Optimal conditions were obtained for catalyst type, and pH. The titanium dioxide proved to be very effective catalysts in photo-catalytic degradation of real refinery wastewater. The maximum degradation achieved was 40.68% by using TiO₂ at 37 °C and pH of 4, within 120 min of irradiations. When TiO₂ was combined with H₂O₂ the degradation decreased to 25.35%. A higher reaction rate was found for titanium dioxide. The results indicate that for real refinery wastewater, TiO₂ is comparatively more effective than ZnO and H₂O₂. The experiments indicated that first-order kinetics can successfully describe the photo-catalytic reaction. The ANOVA results for the model showed satisfactory and reasonable adjustment of the second-order regression model with the experimental data. The ANOVA results also showed that pH is significant than reaction time and catalyst dosage of TiO₂; and in case of ZnO, reaction time is significant than pH and catalyst dosage. This study proves that real refinery wastewater reacts differently than synthetic refinery wastewater, oil field produced water or oil water industrial effluent.     

Recycling of valuable chemicals through the catalytic decomposition of phenol tar in cumene process

The base catalyst LZ-2, which was the mixture of CaO and Na–NaOH/Al₂O₃·3H₂O, was chosen for the decomposition of phenol tar to generate valuable chemicals. The selectivity of LZ-2 for dimethyl phenyl carbinol, α-methyl styrene dimer and cumenyl phenol was 100%, 100% and 98%, respectively. Under the optimum operating conditions of catalyst 2.5 wt%, operating temperature 603.15 K and decomposition time 3.5 h, decomposition ratios of cumenyl phenol and dimethyl phenyl carbinol were 98.7% and 99.97%, respectively. In addition, the experimental repeatability demonstrated that the total yield of valuable chemicals still reached 90.1% after the catalyst being used five times. Mass and energy balance indicated that the catalytic decomposition was a high potential for the recycling of chemicals from phenol tar.     

Experimental study of the characteristics of solid fuel from fry-dried swine excreta

Swine excreta were dried by boiling via immersion in hot oil. In this method, moisture in the excreta is replaced with oil or evaporated by turbulent heat transfer in high-temperature oil. The dried excreta can be used in an incinerator like low-rank coal or solid fuel. Refined waste oil and B–C heavy oil were used for drying. Drying for 8 min at 150 °C reduced the water content of raw excreta from 78.90 wt.% to 1.56 wt.% (refined waste oil) or 1.62 wt.% (B–C heavy oil) and that of digested excreta from 79.58 wt.% to 3.40 wt.% (refined waste oil) or 3.48 wt.% (B–C heavy oil). The low heating values of the raw and digested excreta were 422 kJ/kg and ?2,713 kJ/kg, respectively, before drying and 27,842–28,169 kJ/kg and 14,394–14,905 kJ/kg, respectively, after drying. A heavy metal analysis did not detect Hg, Pb, Cd, As, and Cr in the dried excreta, but Al, Cu, and Zn, which occur in the feed formula, were detected. Thermogravimetric analysis before and after drying revealed that emission of volatiles and combustion of volatiles and fixed carbon occurred at temperatures of 250–500 °C when air was used as the transfer gas.     

The effects of activated Al2O3 on the recycling of light oil from the catalytic pyrolysis of waste printed circuit boards

The effects of employing activated Al₂O₃ during the catalytic pyrolysis of waste printed circuit boards (WPCBs) are investigated, focusing on the recycling of light oil. Variations in the pyrolysis process are studied through analysis of the phase distribution, water content and boiling point fractions of the resulting products. Product composition and carbon number distribution are analyzed using gas chromatography techniques. The use of activated Al₂O₃ increases the light oil fraction and also reduces the quantity of brominated products formed. It was determined that the best yield of light oil and most efficient debromination resulted from catalytic pyrolysis at 600 °C. Applying catalyst-to-feed ratios in the range of 1.0–1.5 also maximizes the yield of light oil. The major oil fraction resulting from catalytic pyrolysis has a boiling point range of 0–250 °C and carbon number range of C6–C9, showing for use as a potential fuel after suitable treatment such as hydrogenation. At a higher catalyst-to-feed ratio of 2.0, activated Al₂O₃ generates a high proportion of light oil fractions containing a significant quantity of chemicals such as phenol (52.67% at 600 °C), although an overall lower yield of oil is obtained. The oil produced in this manner may also be used as a raw material feedstock for the production of various other useful chemicals.     

Preparation of Co–MgO mixed oxide nanocatalysts for low temperature CO oxidation: Optimization of preparation conditions

In this study, a series of Co–MgO mixed oxides (30 wt.% Co) were prepared by co-precipitation method and employed as catalyst in low temperature CO oxidation reaction. The preparation conditions were optimized by the Taguchi method of experimental design to synthesize a sample with high catalytic performance toward CO oxidation reaction. The effects of four variables, pH of solution, aging temperature, aging time and molarity of precursor solution at three levels were investigated. The optimized sample was characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), temperature programmed desorption of oxygen (O₂-TPD), N₂ adsorption/desorption, thermal gravimetric and differential thermal analysis (TGA/DTA), and transmission electron microscopy (TEM) techniques. The results revealed that the optimized sample showed a mesoporous structure with a narrow pore size distribution centered in the range of 7–17 nm and particle size about 5.5 nm. It was found that the molarity of solution and aging time had the most influence on the CO conversion, respectively. The catalytic results showed that the highest CO conversion obtained from samples synthesized by Taguchi orthogonal array was about 90% at 200 °C, while the CO conversion for optimized sample was 95%. In addition, the effect of operational conditions was studied over optimized sample.     

Effect of ultrasound irradiation and Ni-loading on properties and performance of CeO2-doped Ni/clinoptilolite nanocatalyst used in polluted air treatment

In this research nanocatalysts containing 5, 10 and 15 wt.% of Ni, dispersed by sonication over CeO₂–clinoptilolite composite support were compared toward total oxidation of toluene. Their catalytic performance at different temperatures between 150 and 350 °C was studied based on the oxidative destruction of toluene. The results indicated that the activity of Ni/CeO₂–clinoptilolite nanocatalyst for toluene oxidation increased from 33 to 44% at 250 °C by employing sonochemical method in synthesis of catalyst. Meanwhile, the catalytic activity was also improved when Ni content was increased from 5 to 10 and 15 wt.%. With the aid of several characterization techniques like XRD, FESEM, PSD, EDX, BET and FTIR, the correlation between nanocatalyst structure and its activity was addressed. It is indicated that sonochemical method can lift the catalytic activity due to the better dispersion of catalyst active components and also higher surface area. Among sonicated samples, 15 wt.% Ni nanocatalyst showed the highest toluene oxidation due to the better dispersion of catalyst active components and hence to more effective catalytic sites.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Optimizing the preparation parameters of mesoporous nanocrystalline titania and its photocatalytic activity in water: Physical properties and growth mechanisms

Titania nanomaterial with an anatase structure and 5.6 nm crystallite size and 280.7 m² g⁻¹ specific surface areas had been successfully prepared by sol–gel/hydrothermal route. The effect of pH as a type of autoclave and calcination was studied. Crystallite size and phase composition of the prepared samples were identified. X-ray diffraction analyses showed the presence of anatase with little or no rutile phases. The crystallite size of the prepared TiO₂ with acidic catalyst was both smaller than that prepared with basic catalyst, and was increasing after acidic calcinations by a factor 4–5. Basic calcinations produced a specific increase of 1.5. Rutile ratio and the particle size were increased after calcination at 500 °C. However, TiO₂ powder synthesized using a basic catalyst persisted the anatase phase and a loosely aggregation of particles. Anatase TiO₂ as prepared with acidic catalyst in Teflon lined stainless steel autoclave demonstrated the highest photocatalytic activity for degradation of 2,6-dichlorophenol-indophenol under ultraviolet irradiation with t_½ 0.8 min.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Evaluation of beech for production of bio-char,bio-oil and gaseous materials

Evaluation of Oriental beech (Fagus orientalis L.) was investigated with aspect of thermo-chemical conversion to obtain bio-char, bio-oil and gaseous. When the pyrolysis temperature increased, the bio-char yield decreased. A high temperature and smaller particles increase the heating rate resulting in a decreased bio-char yield. The bio-char obtained are carbon rich, with high heating value and relatively pollution-free potential solid biofuel. The liquefaction yield sharply increased with increasing the temperature near critical temperature and after that. In the pyrolysis, increases of liquid yields are considerably sharply for all of the samples with increasing of pyrolysis temperature from 690 K to 720 K. The beechnut oil was converted to biodiesel in supercritical methanol without using the catalyst. Experiments have been carried out in an autoclave at 493, 523 and 593 K, and with molar ratios of 1:6–1:40 of the oil to methanol. The yield of alkyl ester increased with increasing the molar ratio of oil to alcohol.     

Evaluation of membrane bioreactor for hypersaline oily wastewater treatment

Produced water is a significant waste stream generated in association with oil and gas production. It contains high concentrations of hydrocarbon constituents and different salts. In this study, a membrane sequencing batch reactor (MSBR) was used to treat synthetic and real produced water. The MSBR was evaluated in terms of biodegradation of hydrocarbons in the synthetic produced water with various organic loading rates (OLR) (0.281, 0.563, 1.124, 2.248, and 3.372 kg COD/(m³ day)), cycle time (12, 24, and 48 h), and membrane performance. The effects of salt concentrations at different total dissolved solids (TDS) (35,000, 50,000, 100,000, 150,000, 200,000, and 250,000 mg/L) on biological treatment of the pollutants in the synthetic and real wastewater were studied. At an OLR of 1.124 kg COD/(m³ day), an HRT of 48 h and TDS of 35,000 mg/L, removal efficiencies of 97.5%, 97.2%, and 98.9% of COD, total organic carbon (TOC), and oil and grease (O&G), respectively were achieved. For the real produced water, removal rates of 86.2%, 90.8%, and 90% were obtained for the same conditions. However, with increasing salt content, the COD-removal efficiencies of the synthetic and real produced water were reduced to 90.4% and 17.7%, respectively at the highest TDS.     

Dilute Acid Hydrolysis of Cellulose and Cellulosic Bio-Waste Using a Microwave Reactor System

The dilute acid hydrolysis of grass and cellulose with phosphoric acid was undertaken in a microwave reactor system. The experimental data and reaction kinetic analysis indicate that this is a potential process for cellulose and hemi-cellulose hydrolysis, due to a rapid hydrolysis reaction at moderate temperatures. The optimum conditions for grass hydrolysis were found to be 2.5% phosphoric acid at a temperature of 175°C. It was found that sugar degradation occurred at acid concentrations greater than 2.5% (v/v) and temperatures greater than 175°C. In a further series of experiments, the kinetics of dilute acid hydrolysis of cellulose was investigated varying phosphoric acid concentration and reaction temperatures. The experimental data indicate that the use of microwave technology can successfully facilitate dilute acid hydrolysis of cellulose allowing high yields of glucose in short reaction times. The optimum conditions gave a yield of 90% glucose. A pseudo-homogeneous consecutive first order reaction was assumed and the reaction rate constants were calculated as: k₁ = 0.0813 s⁻¹; k₂ = 0.0075 s⁻¹, which compare favourably with reaction rate constants found in conventional non-microwave reaction systems. The kinetic analysis would indicate that the primary advantages of employing microwave heating were to: achieve a high rate constant at moderate temperatures: and to prevent ‘hot spot’ formation within the reactor, which would have cause localised degradation of glucose.     

Optimization of biodiesel production by alkali-catalyzed transesterification of used frying oil

Biodiesel as an alternative fuel for fossil diesel has many benefits such as reducing regulated air pollutants emissions, reducing greenhouse gases emissions, being renewable, biodegradable and non-toxic. In this study, used frying oil was applied as a low cost feedstock for biodiesel production by alkali-catalyzed transesterification. The design of experiments was performed using a double 5-level-4-factor central composite design coupled with response surface methodology in order to study the effect of factors on the yield of biodiesel and optimizing the reaction conditions. The factors studied were: reaction temperature, molar ratio of methanol to oil, catalyst concentration, reaction time and catalyst type (NaOH and KOH). A quadratic model was suggested for the prediction of the ester yield. The p-value for the model fell below 0.01 (F-value of 27.55). Also, the R² value of the model was 0.8831 which indicates the acceptable accuracy of the model. The optimum conditions were obtained as follows: reaction temperature of 65 °C, methanol to oil molar ratio of 9, NaOH concentration of 0.72% w/w, reaction time of 45 min and NaOH as the more effective catalyst. In these conditions the predicted and observed ester yields were 93.56% and 92.05%, respectively, which experimentally verified the accuracy of the model. The fuel properties of the biodiesel produced under optimum conditions, including density, kinetic viscosity, flash point, cloud and pour points were measured according to ASTM standard methods and found to be within specifications of EN 14214 and ASTM 6751 biodiesel standards.     

Optimization of mixture ratio of electrolyte for reducing activation resistance of proton exchange membrane fuel cell

The purpose of this study is to find an optimal mixture ratio of the platinum-loaded carbon catalyst and the electrolyte in a membrane electrode assembly (MEA) of a proton exchange membrane fuel cell for reducing the activation resistance, which influences the electrochemical surface area, activation polarization, and maximum power density of the MEA. First, mixture ratios of 10, 20, 40, and 60 wt% platinum-loaded carbon catalysts and electrolyte were examined. The results indicated that the fuel cell performance improved for mixing weight ratios of 1.0:2.0 in 10 wt% Pt/C, 1.0:1.8 in 20 wt% Pt/C, 1.0:1.1 in 40 wt% Pt/C, and 1.0:0.5 in 60 wt% Pt/C. Next, we evaluated the activation resistances of the MEA from the AC impedance characteristics using the optimal mixing weight ratio of the platinum-loaded carbon catalyst and the electrolyte. It was found that the activation resistances of the anode and cathode decrease with an increase in the weight ratio of platinum-loaded carbon in the catalyst layer.     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Effects of applied voltage on hydrogen production rate of a single reactor BML with Clostridium sp.

This study aimed to explore the influences of single-chamber systems with different applied voltage on bio-hydrogen (H₂) production. The reactor used was the bio-electrochemically assisted microbial reactor (BEAMR) membrane-less (BEAMR-membrane-less, BML). The microbial dark fermentative H₂ production method was adopted. After the hot screening process and the DNA sequencing, the domesticated dominant microflora was Clostridium sp. This study discussed the influences of the cases with (continuous and intermittent) and without applied voltage separately. The results showed that, the H₂ production rate of the case with intermittent applied voltage (117 mL/h g VSS) of 0.24 V was increased of 1.7 folds higher than the without applied voltage (69 mL/h g VSS) and 1.3 folds higher than the case with continuous applied voltage (88.2 mL/h g VSS) of 0.24 V. The produced H₂ concentration with intermittent applied voltage was 18.9% (18.6–19.1%) higher than the without applied voltage, while there was no significant difference with continuous applied voltage.     

7 mT static magnetic exposure enhanced synthesis of poly-3-hydroxybutyrate by activated sludge at low temperature and high acetate concentration

The effect of 7 mT (milliTesla) SMF (static magnetic field) on poly-3-hydroxybutyrate (PHB) production was studied at an acetate concentration of 260 Cmmol l^?1 and temperature of 10 °C. The SMF decreased the specific acetate uptake rate by 29%, but increased the maximum PHB content and the yield of PHB on acetate by 32 and 28% respectively. The ratio q_P/(q_S ? q_P), which described specific PHB production rate over the difference between specific acetate uptake rate and specific PHB production rate, was introduced for evaluation of the ratio of carbon flux into PHB synthesis and into the TCA (tricarboxylic acid) cycle. This value reached 2.3 when activated sludge culture was exposed to magnetic field of 7 mT, which was 1.1 times higher than the q_P/(q_S ? q_P) value obtained without magnetic exposure. Therefore, the SMF promoted diversion of more acetyl-CoA towards PHB synthesis and could offset adverse effects of high acetate concentration and low temperature. These results provide evidence that SMF enhances PHB production by activated sludge.