Improving disintegration and acidification of waste activated sludge by combined alkaline and microwave pretreatment

The individual alkaline or microwave pretreatment has been proved to be effective in disintegration and acidification of waste activated sludge (WAS). In this study, the effects of combined alkaline and microwave pretreatment at different pH and specific energy input (Es) on WAS disintegration were investigated using response surface methodology (RSM). Combined pretreatment achieved disintegration degree (DD) of 65.87% at Es of 38,400 kJ/kg TS and pH 11.0. The ANOVA further demonstrated that pH showed more significant effect on DD than Es. Anaerobic batch experiment results showed that combined pretreatment not only significantly improved volatile fatty acids (VFAs) accumulation but also shortened the time for the highest VFAs accumulation. The maximal VFAs accumulation (1500 mg COD/L) obtained at Es of 28,800 kJ/kg TS and fermentation time of 72 h, which was about two times that of the treatment without microwave (850 mg COD/L) at 96 h. The analysis of VFAs composition showed that the VFAs mainly consisted of acetic and iso-valeric acids, accounting for 57.3–70.1% of total VFAs.     

Effect of ultrasound irradiation and Ni-loading on properties and performance of CeO2-doped Ni/clinoptilolite nanocatalyst used in polluted air treatment

In this research nanocatalysts containing 5, 10 and 15 wt.% of Ni, dispersed by sonication over CeO₂–clinoptilolite composite support were compared toward total oxidation of toluene. Their catalytic performance at different temperatures between 150 and 350 °C was studied based on the oxidative destruction of toluene. The results indicated that the activity of Ni/CeO₂–clinoptilolite nanocatalyst for toluene oxidation increased from 33 to 44% at 250 °C by employing sonochemical method in synthesis of catalyst. Meanwhile, the catalytic activity was also improved when Ni content was increased from 5 to 10 and 15 wt.%. With the aid of several characterization techniques like XRD, FESEM, PSD, EDX, BET and FTIR, the correlation between nanocatalyst structure and its activity was addressed. It is indicated that sonochemical method can lift the catalytic activity due to the better dispersion of catalyst active components and also higher surface area. Among sonicated samples, 15 wt.% Ni nanocatalyst showed the highest toluene oxidation due to the better dispersion of catalyst active components and hence to more effective catalytic sites.     

The effects of activated Al2O3 on the recycling of light oil from the catalytic pyrolysis of waste printed circuit boards

The effects of employing activated Al₂O₃ during the catalytic pyrolysis of waste printed circuit boards (WPCBs) are investigated, focusing on the recycling of light oil. Variations in the pyrolysis process are studied through analysis of the phase distribution, water content and boiling point fractions of the resulting products. Product composition and carbon number distribution are analyzed using gas chromatography techniques. The use of activated Al₂O₃ increases the light oil fraction and also reduces the quantity of brominated products formed. It was determined that the best yield of light oil and most efficient debromination resulted from catalytic pyrolysis at 600 °C. Applying catalyst-to-feed ratios in the range of 1.0–1.5 also maximizes the yield of light oil. The major oil fraction resulting from catalytic pyrolysis has a boiling point range of 0–250 °C and carbon number range of C6–C9, showing for use as a potential fuel after suitable treatment such as hydrogenation. At a higher catalyst-to-feed ratio of 2.0, activated Al₂O₃ generates a high proportion of light oil fractions containing a significant quantity of chemicals such as phenol (52.67% at 600 °C), although an overall lower yield of oil is obtained. The oil produced in this manner may also be used as a raw material feedstock for the production of various other useful chemicals.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

Liquefaction of sawdust in hot compressed ethanol for the production of bio-oils

Direct liquefaction of lignocellulosic waste (sawdust) has been conducted in hot-compressed ethanol at temperatures from 150 to 250 °C. It was found that polyols such as glycerol, glycol and polyethylene glycol (PEG) promoted liquefaction process assisted with hot ethanol treatments seemed promising for production of bio-oils from lignocellulosic materials. Effects of different solvents and catalysts on liquefaction of sawdust were investigated. The results showed that the optimum operating condition for catalytic liquefaction is at 250 °C, 1 h of reaction time using glycerol and ethanol as solvent where operating at this condition realized the highest conversion of sawdust which is 97.8%. After reaction, the liquified product was separated by vacuum distillation. Two fractions were obtained, namely light oil and heavy oil. The properties and compositions of these two fractions were characterized in terms of Fourier transform infrared spectroscopy (FT-IR), gas chromatography–mass spectrometry (GC–MS), size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR).     

Evaluation of membrane bioreactor for hypersaline oily wastewater treatment

Produced water is a significant waste stream generated in association with oil and gas production. It contains high concentrations of hydrocarbon constituents and different salts. In this study, a membrane sequencing batch reactor (MSBR) was used to treat synthetic and real produced water. The MSBR was evaluated in terms of biodegradation of hydrocarbons in the synthetic produced water with various organic loading rates (OLR) (0.281, 0.563, 1.124, 2.248, and 3.372 kg COD/(m³ day)), cycle time (12, 24, and 48 h), and membrane performance. The effects of salt concentrations at different total dissolved solids (TDS) (35,000, 50,000, 100,000, 150,000, 200,000, and 250,000 mg/L) on biological treatment of the pollutants in the synthetic and real wastewater were studied. At an OLR of 1.124 kg COD/(m³ day), an HRT of 48 h and TDS of 35,000 mg/L, removal efficiencies of 97.5%, 97.2%, and 98.9% of COD, total organic carbon (TOC), and oil and grease (O&G), respectively were achieved. For the real produced water, removal rates of 86.2%, 90.8%, and 90% were obtained for the same conditions. However, with increasing salt content, the COD-removal efficiencies of the synthetic and real produced water were reduced to 90.4% and 17.7%, respectively at the highest TDS.     

Thermal characterization of fly ash from one municipal solid waste incinerator (MSWI) in Shanghai

This study aims to develop a methodology for the thermal characterization of MSWI fly ash. We performed TGA–DTA and component variation analysis, microstructure transfer of sintered fly ash, as well as leaching toxicity, volatilization ratio and specification transformation of heavy metals as a function of temperature. It is found that content of crystal phases first increases between room temperature and 800 °C and then decreases between 800 °C and 1200 °C, while that of glass phases registers a reverse trend. Fly ash registers a SiO₂–Al₂O₃–metal oxides system and its content of glass phases is around 57%. Increase of sintering temperature between 600 °C and 1200 °C is conducive to the reduction of soluble As, Cd, Cu, Hg, Pb, Ni and Zn, while content of soluble Cr increases as temperature rises from 800 °C to 1200 °C.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Characterization of heavy metals in fly ash from municipal solid waste incinerators in Shanghai

This study aims to develop a methodology for analysis of characteristics of heavy metals in MSWI fly ash. It performed analysis of composition of heavy metals, leaching toxicity, leaching behavior as a function of pH, specification distribution and corresponding mineral components of residue derived from each step of the sequential extraction. It is found that content of heavy metals follows the sequence of Zn > Pb > Cu > Cr > As > Ni > Cd approximately Hg in both plants, and that total heavy metals account for less than 1% by mass of fly ash. Major hazardous heavy metals in fly ash are As, Cd, Hg, Pb and Zn, whose leaching ratios exceed the limit value described in hazardous waste identification standard. Measured leaching results of Cu, Pb and Zn are essentially consistent with the simulated results at pH between 0 and 13. Content of calcium-silicates, alumino-silicates and glass phases in residue derived from sequential extraction procedure increases steadily from the first step to the fifth step of the sequential extraction procedure. Cu, As, Cr, Hg, Cd, and Ni, relatively stable under strong basic conditions, can be leached out under strong acidic conditions, while Zn and Pb tend to be leached out under both strong acidic and basic conditions.     

The electrocoagulation/flotation study: The removal of heavy metals from the waste fountain solution

The objective of this study was to investigate the possibility of heavy metals (copper, zinc and nickel) removal from the waste fountain solution by the electrocoagulation/flotation (ECF) treatment. After the printing process, the fountain solution changes its composition due to direct contact with different printing materials (plates, inks, etc.) and becomes enriched with metals. The effect of operational parameters, such as electrode materials and combinations, current density, interelectrode distance and operating time, was studied. Also, response surface methodology (RSM) was applied to evaluate the effect of main operational variables and to get a balanced removal efficiency of metals from waste fountain solution by ECF treatment. The iron/iron electrode combination yields a higher percentage of copper and zinc removal efficiency (>95% and >80%, respectively), while for nickel the aluminum/iron and iron/aluminum electrode combinations (>95 and >85%, respectively) proved to be more successful. The optimum interelectrode distance was 1.0 cm (for copper) and 1.5 cm (for zinc and nickel) for all current densities. Heavy metal removal efficiency increases with the increase of electrolysis time for all electrode combinations. Also, the increase of current density improves the ECF removal efficiency. Based on the results obtained through RSM, the optimized parameters for the ECF waste fountain solution treatment for metal removal were identified as: Fe(−)/Al(+) electrode with interelectrode distance of 1.5 cm, operating time of 60 min and current density of 8 mA cm⁻². Overall, the ECF treatment was proven very efficient in the removal of heavy metals from the waste fountain solution under optimum conditions.     

Optimization of biodiesel production from the waste cooking oil using response surface methodology

In this research, transesterification of the waste cooking oil has been studied. Response surface methodology (RSM) based on Box–Behnken design was used to investigate the effects of the main operating parameters, including the methanol to oil molar ratio, catalyst concentration, and reaction temperature, on the biodiesel yield. The results revealed that the catalyst concentration is the most important parameter. The maximum biodiesel yield under the optimized conditions was 99.38 wt.%. Thermogravimetric analysis (TGA) was used for the determination of biodiesel conversion and the results were compared with that of gas chromatography (GC) analysis, showing a very small difference. Furthermore, an empirical quadratic equation has been presented to show the relation between biodiesel conversion and product viscosity.     

Prevalence of work-site injuries and relationship between obesity and injury among U.S. workers: NHIS 2004–2012

Introduction: Studies have reported associations between obesity and injury in a single occupation or industry. Our study estimated the prevalence of work-site injuries and investigated the association between obesity and work-site injury in a nationally representative sample of U.S. workers. Methods: Self-reported weight, height, and injuries within the previous three months were collected annually for U.S. workers in the National Health Interview Survey (NHIS) from 2004–2012. Participants were categorized as normal weight (BMI: 18.5–24.9 kg/m²), overweight (BMI: 25.0–29.9), obese I (BMI: 30.0–34.9), and obese II (BMI: 35 +). The prevalence of injury and prevalence ratios from fitted logistic regression models was used to assess relationships between obesity and injury after adjusting for covariates. Sampling weights were incorporated using SUDAAN software. Results: During the 9-year study period from 2004 to 2012, 1120 workers (78 workers per 10,000) experienced a work-related injury during the previous three months. The anatomical sites with the highest prevalence of injury were the back (14.3/10,000 ± 1.2), fingers (11.5 ± 1.3), and knees (7.1 ± 0.8). The most common types of injuries were sprains/strains/twists (41.5% of all injuries), cuts (20.0%), and fractures (11.8%). Compared to normal weight workers, overweight and obese workers were more likely to experience work-site injuries [overweight: PR = 1.25 (95% CI = 1.04–1.52); obese I: 1.41 (1.14–1.74); obese II: 1.68 (1.32–2.14)]. These injuries were more likely to affect the lower extremities [overweight: PR = 1.48, (95% CI = 1.03–2.13); obese I: 1.70 (1.13–2.55); obese II: 2.91 (1.91–4.41)] and were more likely to be due to sprains/strains/twists [overweight: PR = 1.73 (95% CI = 1.29–2.31); obese I: PR = 2.24 (1.64–3.06); obese II: PR = 2.95 (2.04–4.26)]. Conclusions: Among NHIS participants, overweight and obese workers were 25% to 68% more likely to experience injuries than normal weight workers. Practical applications: Weight reduction policies and management programs may be effectively targeted towards overweight and obese groups to prevent or reduce work-site injuries.     

Biohydrogen production using waste activated sludge as a substrate from fructose-processing wastewater treatment

Biohydrogen production by dark fermentation in a series of batch tests under different environmental control conditions was evaluated to determine the optimal initial cultivation pH and temperature for a continuous-flow kinetic test to validate the kinetic model system. The waste activated sludge (WAS) from fructose-processing manufacturing was used as the model substrate for biohydrogen production. The batch experiments for biohydrogen production were conducted in a 6 l bioreactor. Fifteen batch kinetic tests were investigated when pH was controlled at 6, 7, 8 and 9 as well as the temperature was controlled at 37 °C, 45 °C and 55 °C, respectively. The experimental results indicated that the optimal operational condition for hydrogen production occurred while pH was 7 and temperature was 55 °C with the highest hydrogen production of 7.8 mmol. The optimal recovery time for hydrogen was 25 h in the batch experiments. Furthermore, the kinetic test of biohydrogen production was performed by anaerobic mixed microbial culture in the continuous-flow experiment when pH and temperature was maintained at 7 and 55 °C. Approximately 60% and 7% of substrate solution was converted into acetate and hydrogen, respectively, at the steady state. Roughly only 0.77% and 2.7% of substrate solution was converted into propionate and butyrate, respectively, at a steady-state condition. The experimental and modeling approaches presented in this study could be employed for the design of pilot-scale and full-scale anaerobic biohydrogen fermentors using food-processing waste activated sludge (WAS) as a substrate solution.     

Partial nitritation of landfill leachate with varying influent composition under intermittent aeration conditions

The start-up and operation of a partial nitritation sequencing batch reactor for the treatment of landfill leachate were carried out on intermittent aeration mode. Partial nitrite accumulation was established in 15 days after the mode was changed from continuous aeration to intermittent aeration. Despite the varying influent composition, partial nitritation could be maintained by adjusting the hydraulic retention time (HRT) and the air flow rate. An increase in the air flow rate together with a decrease in air off duration can improve the partial nitritation capacity and eventually result in the development of granular sludge with fine diameters. A nitrogen loading rate of 0.71 ± 0.14 kg/m³/d and a COD removal rate of 2.21 ± 0.13 kg/m³/d were achieved under the conditions of an air flow rate of 19.36 ± 1.71 m³ air/m³/h and an air on/off duration of 1.5 min/0.7 min. When the ratio of total air flux (TAF) to the influent loading rate (ILR) was controlled at the range of 163–256 m³ air/kg COD, a stable effluent NO₃^?–N/NO_x^?–N (NO₂^?–N plus NO₃^?–N) ratio below 13% was achieved. Interestingly, the effluent pH was found to be a good indicator of the effluent NO₂^?–N/NH₄⁺–N ratio, which is an essential parameter for a subsequent anaerobic ammonium oxidation (Anammox) reactor.     

Biosorption of zinc(II) on rapeseed waste: Equilibrium studies and thermogravimetric investigations

The removal of heavy metals from aqueous effluents so as to avoid their toxic, bioaccumulation and biomagnification effects to humans and environment is usually realized by means of physical, chemical treatment, and biological processes. The aim of this study is to evaluate the potential of rapeseed waste from biodiesel production as a biosorbent for Zn(II) ions.The ability of the rapeseed waste for Zn(II) biosorption exhibited a maximum at pH 4.5–5. The removal efficiency of Zn(II) from solution with an initial concentration of 72 mg L⁻¹ varied from 39% to 89% for an increase of the rapeseed waste dose from 2 to 30 g L⁻¹. The amount of Zn(II) retained on the tested rapeseed increased with increasing metal ion concentration, but the Zn(II) sorption percentage decreased. The equilibrium data are fitted to the Langmuir isotherm better than to the Freundlich isotherm. The kinetics of Zn(II) biosorption process follows a pseudo-second order model. The thermal stability of the rapeseed before and after Zn(II) biosorption was studied by thermogravimetric analysis. It was found that the zinc loaded rapeseed exhibits a better initial thermal stability than the original rapeseed, presumably due to the cross linking generated by the intermolecular complexation of Zn(II) ions. In both cases, the thermal decomposition takes place according to some reassembling kinetic models, in two phases with order n reactions. The results of this study strongly suggest the possibility to use rapeseed as an effective biosorbent for Zn(II) ions removal from aqueous effluents (municipal/industrial wastewaters).     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

Kinetic analysis of transesterification of waste pig fat in supercritical alcohols

The kinetic analysis method using non-isothermal technique was proposed to determine the kinetic parameters for the transesterification reaction of waste pig fat in supercritical alcohols. To investigate the transesterification of waste pig fat, the waste pig fat to alcohol ratio (w/w) was varied from 1:1.5 to 1:2.5 between the temperatures 220 and 290 °C at an interval of 10 °C in a 25 mL batch reactor. The products were analyzed by gas chromatography mass spectrometry. To verify the effectiveness of the proposed kinetic analysis method, the experimental values were compared with the values calculated using the kinetic parameters obtained from this work. It was found that the proposed kinetic analysis method gave reliable kinetic parameters for the transesterification of waste pig fat in supercritical alcohols. Further, it was found that the apparent activation energy for supercritical ethanol was lower than the value for supercritical methanol.     

Comparative response of two organic biofilters treating ethylbenzene and toluene after prolonged exposure

The response of two biofilters filled with an organic waste material for treating ethylbenzene and toluene was studied for 415 and 472 operating days, respectively. The peak elimination capacities (EC_MAX) recorded were 170 g m^?3 h^?1 for ethylbenzene (EC_MAX) and 138 g m^?3 h^?1 for toluene. Regarding the degradation profile through the biofilters, an increase in the inlet concentration displaced the degradation profile into the downstream section. A sudden decrease in the performance of both biofilters occurred when the moisture content (MC) of the packing material exceeded 37% for ethylbenzene and 30% for toluene. Thus, a recommended MC value was established in the 15–30% range. Given the bioreactor was operated at a low MC level, fungi prevailed over bacteria. Nevertheless, synergism was detected between both microorganism types for the mineralization of the aromatic hydrocarbons.     

Environmental and eco-costs life cycle assessment of an acrylonitrile process by capacity enlargement in Mexico

Life cycle assessment and marginal prevention costs (eco-costs method) for an acrylonitrile plant were carried out estimating the environmental impact and the eco-costs, due to the increment in the production capacity. This study compares the old plant's operative performance (old design) at 50,000 ton/year where the by-products were incinerated, with the current operation at 60,000 ton/year where those by-products in the waste stream will be treated to take advantage of its substance content, to generate profitable products. In addition, the effect of a wastewater flow rate with cyanide was evaluated on the biological wastewater treatment process.The redesign showed a high reduction percentage in eleven of eighteen midpoint impact categories. The reduction of 36% in the global impacts in the redesign was obtained when these ones were calculated based on the impacts of the year of 2005. The CO₂ emissions equivalents (CO₂eq) had a reduction of 46% (from 6.55 to 3.50 kg CO₂eq/kg of acrylonitrile). The total of marginal prevention costs (eco-costs) are 1.28 USD/kg for acrylonitrile old design and the 0.735 USD/kg for acrylonitrile redesign, i.e. 42.5% lower than the old design. This means that 94.5% are costs for pollution and the use of energy and 5.4% by depletions of material resources.This study proved that the redesign is environmentally most favorable and economically affordable method.Eco-costs method should be incorporated as part of the financial indicators of a project, but with the respective adaptation to the environmental and economic conditions of a region.     

Sensitivity analysis and optimization for gasoline vapor condensation recovery

Volatile organic compounds (VOCs) are easily evaporated and discharged from everywhere into the atmosphere, especially in various operations of gasoline. The emission of VOCs is always a significant environmental problem, and the control of VOCs pollution has been a hot topic in the field of air purification. In this paper, the condensation separation method for gasoline vapor recovery was investigated and four gasoline vapors of S1–S4 were selected for the sensitivity analysis and optimization of the condensation process, using the Model Analysis Tools from Aspen Plus. Generally, to control VOCs pollution efficiently, both the vapor recovery efficiency and the outlet vapor concentration of the condensation recovery system should be simultaneously considered. Then an optimized three-stage condensation process was proposed, whose condensation temperatures were optimized and designed at 1 °C, −40 °C and −110 °C, respectively. Further, based on the comprehensive consideration of both meeting the more strict VOCs emission standard and ensuring the condensation recovery system work stably and economically, it was recommended that the maximum total vapor recovery efficiencies for S1–S4 should be 99.73%, 99.79%, 99.82% and 99.19%, and the minimum outlet vapor concentrations be 2.87 g/m³, 2.75 g/m³, 3.04 g/m³ and 16.98 g/m³, respectively. Accordingly, the condensation temperature of the copious cooling stage should be set at −130 °C. Moreover, the total cooling duties for the single-stage and three-stage condensation processes were investigated and compared when the condensation temperature of the recovery system ranged from 20 °C to −110 °C. The total cooling duties of the three-stage condensation process for S1–S4 would be saved by 12.23%, 15.68%, 13.96% and 15.65%, respectively. Finally, a three-stage condensation system was developed for the industrial gasoline vapor recovery, which has performed well since its installation.