Furniture wood wastes: Experimental property characterisation and burning tests

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected “raw” and primarily “engineered” (“composite”) wood wastes.The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in “engineered” wood wastes as compared with “raw” wood wastes; and relatively high energy content values of “engineered” wood wastes (ranging on the whole from 3675 to 5105 kcal kg⁻¹ for HHV, and from 3304 to 4634 kcal kg⁻¹ for LHV).The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in “engineered” wood burning tests of pyrroles and amines, as well as the additional presence (as compared with “raw” wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon.Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in “engineered” wood burning tests as compared with “raw” wood burning test; and considerable generation of the respirable PM₁ fraction during incomplete industrial wood burning.     

Removal of copper,chromium, and arsenic from CCA-C treated wood by EDTA extraction

Ethylenediaminetetracetic acid (EDTA) is one of the most common chelators used to bind the metal ions in extremely stable complexes in heavy metal contaminated soils and thus to remediate such substrates. EDTA forms water soluble complexes with many metal ions and it is used to release the various metals. In this study, EDTA extraction of copper, chromium, and arsenic from chromated copper arsenate (CCA-C) treated wood was evaluated using batch leaching experiments. CCA-treated wood samples were extracted with eight different concentrations of EDTA for 4, 8, 18, and 24 h at room temperature. Exposing CCA-treated chips and sawdust to EDTA extraction enhanced removal of CCA components compared with extraction by deionized water. Grinding CCA-treated wood chips into 40-mesh sawdust provided greater access to and removal of CCA components. Extraction with 1% EDTA solution for 24 h removed 60% copper, 13% chromium, and 25% arsenic from treated chips. EDTA extraction of treated sawdust samples resulted in 93% copper, 36% chromium, and 38% arsenic removal. CCA leaching from treated wood blocks was also evaluated according to modified AWPA E11-99 standard test method of determining the leachability of wood preservatives. Leaching of CCA components from treated wood blocks with 1% EDTA solution for 14 days caused more copper leaching compared to leaching with deionized water. Leaching with 1% EDTA for 14 days removed 53% copper from the blocks whereas 14% copper was leached from the blocks with deionized water. The results suggest that EDTA extraction removes significant quantities of copper from CCA-treated wood. Thus, EDTA could be important in the remediation of wood waste treated with the newest formulations of organometalic copper compounds and other water-borne wood preservatives containing copper.     

Online sorting of recovered wood waste by automated XRF-technology. Part I: detection of preservative-treated wood waste

Waste wood is frequently contaminated with wood treatment preservatives including chromated copper arsenate (CCA) and alkaline copper quat (ACQ), both of which contain metals which contaminate recycled wood products. The objective of this research was to propose a design for online automated identification of As-based and Cu-based treated wood within the recovered wood waste stream utilizing an X-ray fluorescence (XRF) system, and to evaluate the detection parameters of such system. A full-scale detection unit was used for experimentation. Two main parameters (operational threshold (OT) and measurement time) were evaluated to optimize detection efficiencies. OTs of targeted metals, As and Cu, in wood were reduced to 0.02 and 0.05, respectively. The optimum minimum measurement time of 500 ms resulted in 98%, 91%, and 97% diversion of the As, Cu and Cr mass originally contained in wood, respectively. Comparisons with other detection methods show that XRF technology can potentially fulfill the need for cost-effective processing at large facilities (>30 tons per day) which require the removal of As-based preservatives from their wood waste stream.     

Fungicidal value of wood tar from pyrolysis of treated wood

The objective of the paper was to estimate the fungicidal value of wood tar extracted as a product of pyrolysis of wood previously treated with either creosote oil or CCB-type salt preservative. The effectiveness of wood treated with one of these two wood tar residuals was compared to the effectiveness of wood treated with virgin creosote oil (type WEI-B) and an untreated control. Wood was impregnated with alcohol solutions of the two extracted preservatives or virgin creosote oil and then subjected to the Coniophora puteana, Poria placenta and Coriolus versicolor fungi. The fungicidal values of the investigated preservatives were determined with the use of the short agar-block method and the aging test according to the standard EN 84. It was found that wood tar extracted by pyrolysis of old creosote-treated wood and then used to treat wood may have potential as a preservative for wood protection or as a component of preservatives.     

Effect of composting on the Cd,Zn and Mn content and fractionation in feedstock mixtures with wood chips from a short-rotation coppice and bark

Micronutrient content and availability in composts may be affected by the addition of wood chips or tree bark as a bulking agent in the compost feedstock. In the first part of this study, micronutrient levels were assessed in bark and wood of poplar and willow clones in a short-rotation coppice. Large differences between species were observed in bark concentrations for Cd, Zn and Mn. In the second part of the study, we aimed to determine the effect of feedstock composition and composting on Cd, Zn and Mn concentrations and availability. By means of three composting experiments we examined the effect of (a) bark of different tree species, (b) the amount of bark, and (c) the use of bark versus wood chips. In general, compost characteristics such as pH, organic matter and nutrient content varied due to differences in feedstock mixture and composting process. During the composting process, the availability of Cd, Zn and Mn decreased, although the use of willow and poplar bark or wood chips resulted in elevated total Cd, Zn or Mn concentrations in the compost. Cd concentrations in some composts even exceeded legal criteria. Cd and Zn were mainly bound in the reducible fraction extracted with 0.5 M NH₂OH?HCl. A higher acid-extractable fraction for Mn than for Cd and Zn was found. Higher Cd concentrations in the compost due to the use of bark or wood chips did not result in higher risk of Cd leaching. The results of the pH-stat experiment with gradual acidification of composts illustrated that only a strong pH decline in the compost results in higher availability of Cd, Zn and Mn.     

Synthesis and identification of graft copolymers of wood pulp and styrene

Based on the graft copolymerization reactions of lignin and vinyl monomers, a series of graft copolymers of wood pulp and styrene (1-phenylethene) has been synthesized. The wood pulps used in this research are unbleached products produced by chemical, thermal, and mechanical pulping. All of them contain a high content of lignin (25–29 wt%). The grafting reaction is a free radical polymerization coinitiated by calcium chloride, hydrogen peroxide, and wood pulp in dimethylsulfoxide at 30°C. The effect of reaction temperature, reaction time, and the amount of the reactants on the conversion of monomer, yield of product, weight increase of pulp, and grafting efficiency of monomer has been studied. The grafted wood pulp was separated from homopolystyrene formed during the reaction by extraction of the reaction product with benzene in a Soxhlet apparatus for at least 48 h. The results show that after the reaction, the weight of all wood pulps was significantly increased and the weight increase of very high yield sodium bisulfite pulp (VHYS) was 333%. This proves that a part of the polymerized styrene was chemically bound to the wood pulp. The Fourier transform infrared (FTIR) spectra of the extracted products show absorbance peaks characteristic of both wood and polystyrene and, thus, provide strong proof of grafting. Grafting has completely changed the surface properties of the starting wood pulp from hydrophilic to hydrophobic, and under ordinary thermal compression conditions, thermoplastic composite objects of good uniformity can be made directly from reaction products which contain up to 52 wt% wood pulp.     

Total recycling of CCA treated wood waste by low-temperature pyrolysis

A system to turn a potentially harmful stream of solid waste into a set of substreams with either commercial value or highly concentrated residual streams is presented. The waste which is considered is metal impregnated (in particular Chromated Copper Arsenate (CCA) treated) wood waste and timber, such as telephone poles, railway sleepers, timber from landscape and cooling towers, wooden silos, hop-poles, cable drums and wooden playground equipment. These waste streams sum up to several 100,000 tons of material per year currently to be dumped in every major country of the European Community (EC). Technologies need to be developed to reduce this CCA treated wood waste, such that all of the metals are contained in a marketable product stream, and the pyrolysis gases and/or pyrolysis liquid are used to their maximum potential with respect to energy recuperation. Pyrolysing the CCA treated wood waste may be a good solution to the growing disposal problem since low temperatures and no oxidising agents are used, which result in lower loss of metals compared to combustion. An experimental labscale pyrolysis system has been developed to study the influence of the pyrolysis temperature and the duration of the pyrolysis process on the release of metals and the mass reduction. The macrodistribution and microdistribution of the metals in the solid pyrolysis residue is studied using Inductively Coupled Plasma Mass Spectrometry (ICP–MS) and Scanning Electron Microscopy coupled with Energy Dispersive X-ray Analysis (SEM–EDXA). Furthermore, a complete mass balance is calculated over the pyrolysis system. Based on these results a semi-industrial pyrolysis system (pilot plant scale) has been developed consisting of three stages: grinding, packed bed pyrolysis and metal separation. Special types of equipment have been developed to carry out the three stages. A new grinding system has been developed, based on a crushing mechanism rather than a cutting mechanism. The crushed wood is introduced by means of a screw feeding system into a reaction column. In this pyrolysis reactor the wood is heated by subjecting it to a flow of hot gases. This causes an adiabatic pyrolysis, which results in volatilisation of the volatile compounds whereas the mineral compounds (containing the metals) remain entrapped in a coal-type residue which is very rich in carbon. The condensable compounds in the pyrolysis gas condense while leaving the reaction zone due to the inverse temperature gradient. The pyrolysis gas leaving the reactor is used as fuel for the hot gas generator. The charcoal which is extracted at the bottom of the reactor, is cooled, compressed, removed and stored, ready to feed the subsequent stage. A specially developed grinder is used to remove the metal particles from the charcoal and the separation between metal and charcoal particles is accomplished in a pneumatic centrifuge as a result of the difference in density. Using this system the ultimate waste is less than 3% of the initial wood mass. Results obtained with a semi-industrial scale prototype confirm the effectiveness of the process.     

Nitrous oxide emission from some English and Welsh rivers and estuaries

Nutrient and N₂O concentrations in the water columns were measured seasonally over a full salinity range in the nutrified rivers Colne, Stour, Orwell, Deben, Trent, Ouse and Humber and their estuaries on the east coast of England between August 2001 and May 2002, and in the oligotrophic rivers Conwy, Dovey and Mawddach in North and West Wales between August 2002 and May 2003. Nutrient and N₂O concentrations in the nutrified English rivers and estuaries were much higher than those in the Welsh rivers. N₂O concentrations and % saturation in the estuaries were significantly correlated with nitrate, nitrite and ammonium concentrations in the water. The strongest correlation was with nitrite (r² = 0.56, p < 0.01), suggesting that nitrite was the most significant factor among the different nutrients in regulating N₂O concentration in the estuaries. N₂O concentrations in the English rivers and estuaries were supersaturated throughout the year with annual averages from 186.9 to 992.9%, indicating that these rivers and estuaries were sources of atmospheric N₂O, whereas in the Welsh rivers N₂O concentrations were much lower with annual averages from 113.6 to 137.4% saturation. Although the estuarine area in the Colne was almost the same as that in the Conwy, the annual N₂O emission from the Colne was much higher (937498 mol N yr^–1) than in the Conwy (23020 mol N yr^–1). On the east coast, riverine emissions of N₂O were only 0.5–12.5% of the total emission from rivers and estuaries. Thus rivers were negligible, but estuaries were significant contributors to the UK N₂O inventory.     

Influence of corn steep liquor and glucose on colonization of control and CCB (Cu/Cr/B)-treated wood by brown rot fungi

There are increasing problems with regard to the disposal of treated wood waste. Due to heavy metals or arsenic in impregnated wood waste, burning and landfill disposal options are not considered to be environmentally friendly solutions for dealing with this problem. Extraction of the heavy metals and recycling of the preservatives from the wood waste is a much more promising and environmentally friendly solution. In order to study the scale up of this process, copper/chromium/boron-treated wood specimens were exposed to copper tolerant (Antrodia vaillantii and Leucogyrophana pinastri) and copper sensitive wood decay fungi (Gloeophyllum trabeum and Poria monticola). Afterwards, the ability of fungal hyphae to penetrate and overgrow the wood specimens was investigated. The fungal growths were stimulated by immersing the specimens into aqueous solution of glucose or corn steep liquor prior to exposure to the fungi. The fastest colonization of the impregnated wood was by the copper tolerant A. vaillantii. Addition of glucose onto the surface of the wood specimens increased the fungi colonization of the specimens; however, immersion of the specimens into the solution of corn steep liquor did not have the same positive influence. These results are important in elucidating copper toxicity in wood decay fungi and for using these fungi for bioremediation of treated wood wastes.     

Comparison of the Chemical Composition of Mineral Particles Collected in Dunhuang,China and those Collected in the Free Troposphere over Japan: Possible Chemical Modification during Long-Range Transport

The Asian continent is recognized as one of the most important sources of mineral (or soil) particles. These particles have a large potential to effect global changes through the biogeochemical cycle of particulates and through radiative balance (IPCC Third Assessment Report, 2001). Therefore, comparison of particle compositions near the source region and those after long-range transport is important in understanding the long-range particle transport phenomenon. Individual aerosolparticles were collected in Dunhuang (40°09N; 94°41E), China. Particles were collected at the campus of the Meteorological Bureau of Dunhuang City (17 August 2001) and near the Mogao Grots, located approximately 30 km from Dunhuang (18 August 2001, 18 October 2001 and 13 January 2002) using a two-stage low-volume impactor. The morphology of individual aerosol particles and their elemental compositions were examined via a scanning electron microscope (Hitachi, S-3000N) equipped with an energy dispersive X-ray (EDX) analyzer (Horiba, EMAX-500). The particles collected at these locations were comprised primarily of minerals, with the exception of sulphateparticles in the submicron range that were contained in thesample collected on 18 October 2001 (likely, ammonium sulphate). The most abundant elements were found to be Si and Al. Approximately 46–77% of the collected particles were Si-richparticles (composed primarily of quartz and aluminosilicate),and 13–41% of the collected particles were Ca-rich particles,such as calcite (CaCO₃), dolomite (CaMg(CO₃)₂),and gypsum (CaSO₄2H₂O). The fractions of Fe-rich, Mg-rich, Ti-rich, K-rich, and Cl-rich were 3–10, 0–7, 0–3, 0–1, and 0–1%, respectively. Similar types of mineral particles were found in the free troposphere over Japan(Trochkine et al., 2002). A number of differences were found to exist between the particles collected in China and thosecollected in Japan, and these differences can be explained bychemical modification of the particles during transport fromChina to Japan.     

Wood Modification Effects on Weathering of HDPE-Based Wood Plastic Composites

The effects of weathering on the constituents of wood and polymer matrix behavior in wood plastic composites (WPCs) were investigated. WPCs were produced from pine, extractives-free pine, and pine holocellulose fibers (60%) together with HDPE (40%). These composites were subjected to xenon-arc accelerated and outside weathering for a total of 1200 h and 120 days, respectively. The color and chemical changes that occurred on the surface of the WPCs were analyzed using a set of analytical techniques. For pine and extractive-free pine filled composites, the results showed that the total color change, lightness, and oxidation increased, while the lignin content decreased. In addition, the weight average molecular weight (Mw) and number average molecular weight (Mn) of extracted HDPE decreased with an increase in exposure time of the composites. However, HDPE crystallinity increased with longer exposure time. Lightness of holocellulose-based WPC changed the least while the change in its HDPE crystallinity was not significant compared to the other composite types. Therefore, holocellulose-based WPC may be preferred for applications where color stability is of high priority.     

Potential utilization of burned wood in manufacture of medium density fiberboard

The potential utilization of burned wood in the manufacture of medium density fiberboard (MDF) was investigated. For this aim, the MDF panels were made of various mixtures of burned pine wood (Pinus sylvestris L.), unburned beech (Fagus orientalis L.) and oak (Ouercus robur L.) woods under commercial conditions in an MDF company. The mixture ratio of the unburned beech and oak woods to the burned pine wood were 50/50 wt%. The mixing ratios of burned wood chips with unburned wood chips were 0:100, 25:75, 50:50, 75:25 and 100:0, %, respectively. A commercial urea–formaldehyde resin was used as a binder. The physical properties measured in the investigation included density and thickness swelling, while the mechanical properties examined were bending strength, modulus elasticity, internal bond, screw holding ability perpendicular to the plane of panel, and janka hardness perpendicular to the plane of the panel. Surface roughness and color of the panels were also measured. The results indicated that all the panels met the mechanical properties of general-purpose MDF requirements of EN 622-5. The surface roughness of the MDF panels containing burned wood decreased with increasing burned wood content but remained higher than the control panels. The dimensional stability of the MDF panels decreased with the incorporation of burned wood fibers as compared with the control MDF panels.     

Storage stability of biocrude oils from fast pyrolysis of poultry litter

The unstable nature of biocrude oils produced from conventional pyrolysis of biomass is one of the properties that limits its application. In the disposal of poultry litter via pyrolysis technology, the biocrude oil produced as a value-added product can be used for on farm applications. In this study, we investigated the influence of bedding material (wood shavings) on the storage stability of biocrude oils produced from the fast pyrolysis of poultry litter. The biocrude oils produced from manure, wood (pine and oak), and mixtures of manure and wood in proportions (75:25 50:50, and 25:75 w/w%) were stored under ambient conditions in sealed glass vials for a period of 6 months and their stability were monitored by measuring the changes in viscosity over time. The manure oil had the lowest rate of viscosity change and thus was relatively the most stable and the oils from the 50:50 w/w% litter mixtures were the least stable. The rate of viscosity change of the manure biocrude oil was 1.33 cP/day and that of the 50/50 litter mixture was 7.6 cP/day for pine and 4.17 cP/day for oak.The spectrometric analyses of the biocrude oils showed that the presence of highly reactive oxygenated functionalities in the oil were responsible for the instability characteristic of the litter biocrude oils. The poor stability of the biocrude oil from the 50:50 w/w% litter mixtures was attributed to reactions between nitrogenous compounds (amides) from protein degradation and oxygenated compounds from the decomposition of polysaccharides and lignin. The addition of 10% methanol and 10% ethanol to the oil from 50% manure and 50% pine reduced the initial viscosity of the oil and was also beneficial in slowing down the rate of viscosity change during storage.     

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition,chlorine content and temperature

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature.Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature.     

Improvement of Waste Recycling in PET Fiber Production

Production of polyethylene teraphtalate (PET) fiber in the world is increasing every year and reached to an amount of about 20 million tons a year in 2001. The wastes occur in the production of PET fiber in the amount of about 3–5% of total production. The PET does not degrade for a long time in nature. Since PET is a derivative of petroleum, the wastes of PET are valuable and must be recycled. One of the recycling method of PET wastes is re-melting. Thus, various properties of the PET wastes were improved using the re-melting method by employing an extruder manufactured for the work. Degradation during re-melting decreases the properties of the final product. The results indicate that the properties of recycled PET wastes can be monitored by designing the parameters of the extruder. Also, the further degradation of the material can be prevented and the recycling costs are minimized.     

Influence of pine wood shavings on the pyrolysis of poultry litter

Poultry litter from broilers and turkeys are a mixture of manure, feathers, feed and wood shavings, thus pyrolysis oils produced from this material are influenced by the individual components. In order to determine the influence of wood shavings that are used as bedding material, we investigated the pyrolysis of pine wood shavings and poultry manure. Because manure from layer chickens are usually not contaminated with wood shavings, we made mixtures of layer manure and pine wood shavings in the following manure to wood ratios, 100:0, 75:25, 50:50, 25:75, and 0:100 w/w and pyrolyzed them in a fluidized bed reactor at 450 °C. The total liquid yield ranged from 43.3 to 62.7 wt.%. The layer manure oil had a HHV of 29.7 MJ/kg and pH of 5.89 compared to pine wood oil which had HHV of 25.6 MJ/kg and pH of 3.04. The addition of wood shavings to manure clearly influenced the physical properties of the oil, resulting in a decrease in pH and HHV and an increase in density. The oils had relatively high nitrogen content ranging from 1.36 to 5.88 wt.%. The ash (<0.07 wt.%) and sulfur (<0.28 wt.%) contents were very low. FTIR, ¹³C NMR and ¹H NMR spectrometric analysis of the oils showed that manure oil was rich in hydrocarbons and nitrogenous compounds such as primary, secondary amides, aromatic amines and N-heterocyclic. The properties of the oils were strongly influenced by the amount of wood in the mixture.     

Conversion of CCA-treated wood to ethanol: a method to reduce leaching of metals from disposed treated wood prior to disposal

The objective of this paper is to evaluate the feasibility of producing ethanol from CCA-treated wood that is highly leachable. Following the initial tests, CCA-treated wood was hydrolysed and fermented and the results showed not only that ethanol was produced during the fermentation process but that metals were taken up by the yeast. Toxicity characteristic leaching procedure tests of the hydrolysed wood leached less than 4 mg/L of As while minimal amounts of Cr and Cu remained in the hydrolysed wood which makes landfilling of hydrolysed wood acceptable and less hazardous. A slightly lower amount of ethanol from CCA-treated than untreated wood was produced (6 and 7 g/L, respectively). In general, it suggests that production of ethanol as a source of energy from a hazardous waste (CCA-treated wood) is feasible.     

Monitoring Studies of Precipitation and Cap Cloud Chemistry at Holme Moss in the Southern Pennines

Weekly collections of samples of precipitation and hill cloudwater have been made at Holme Moss (530 m.a.s.l.) in the southernPennines covering a six-year period (1994–1999). In addition continuous meteorological measurements have been conducted at thesite for a five year period (1995–1999). The concentrations of major ions in the samples have been determined by ion chromatography. Analysis of ion concentrations as a function ofwind direction reveals that the ions with anthropogenic sources (SO₄ ^–, NO₃ ^–, NH₄ ⁺, H⁺) exhibit higher concentrations during easterly wind directions whilst the ions with predominantly marine origins (Na⁺, Cl^–, Ca⁺⁺, Mg⁺⁺, K⁺) have concentrations thatare not significantly dependant on wind direction. Precipitation and cloud deposition are strongly correlated to south-westerly wind directions with a secondary peak occurring for north-easterly directions. Fifty nine per cent of ion deposition by rain was found to occur during wind from the SSW to W sector.The average concentrations of ions in cloud water were found tobe much higher than those in rain (by factors of between 2.5 and4.2). It is thought that the high precipitation and annual deposition of ions by precipitation at Holme Moss is due in partto the enrichment of ion concentrations in precipitation by thescavenging of more concentrated cap cloud droplets (the `seeder-feeder effect'). Comparison with data from a nearby lower level site shows encouraging agreement with the scheme currently used in the U.K. deposition mapping procedure to incorporate the influence of orography on deposition by precipitation.     

Management of hazardous waste in Thailand: present situation and future prospects

 This paper deals with the present scenario of hazardous waste management practices in Thailand, and gives some insights into future prospects. Industrialization in Thailand has systematically increased the generation of hazardous waste. The total hazardous waste generated in 2001 was 1.65 million tons. It is estimated that over 300 million kg/year of hazardous waste is generated from nonindustrial, community sources (e.g., batteries, fluorescent lamps, cleansing chemicals, pesticides). No special facilities are available for handling these wastes. There are neither well-established systems for separation, storage, collection, and transportation, nor the effective enforcement of regulations related to hazardous wastes management generated from industrial or nonindustrial sectors. Therefore, because of a lack of treatment and disposal facilities, these wastes find their way into municipal wastewaters, public landfills, nearby dump sites, or waterways, raising serious environmental concern. Furthermore, Thailand does not have an integrated regulatory framework regarding the monitoring and management of hazardous materials and wastes. In addition to the absence of a national definition of hazardous wastes, limited funding has caused significant impediments to the effective management of hazardous waste. Thus, current waste management practices in Thailand present significant potential hazards to humans and the environment. The challenging issues of hazardous waste management in Thailand are not only related to a scarcity of financial resources (required for treatment and disposal facilities), but also to the fact that there has been no development of appropriate technology following the principles of waste minimization and sustainable development. A holistic approach to achieving effective hazardous waste management that integrates the efforts of all sectors, government, private, and community, is needed for the betterment of human health and the environment. Received: February 26, 2001 / Accepted: October 11, 2002     

Factors affecting sodium hypochlorite extraction of CCA from treated wood

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 °C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.