Comparison of the Effect of Plasticizers on PHBV—and Organoclay—Based Biodegradable Polymer Nanocomposites

The aim of this work was to evaluate the effect of different plasticizers on the morphology, crystallization, and mechanical properties of poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)/organomodified montmorillonite (OMt) nanocomposites. We investigated three different plasticizers: dioctyl phthalate (DOP), a commonly used additive in the polymer industry, and two natural and biodegradable plasticizers: epoxidized soybean oil (ESO) and triethyl citrate (TEC). The nanocomposites with 3 wt% OMt were obtained by melt processing in an internal mixer. The plasticizers were used alone or in combination with clay in a concentration of 10 wt%. X-ray diffraction and scanning electron microscopy results revealed a partially intercalated structure. The degree of crystallinity was higher for all of the samples compared to neat PHBV, although the melting temperature decreased with the use of plasticizers combined with OMt. The impact strength results were dependent on the interaction between the components of the system. Triethyl citrate was the most effective plasticizer due to its more pronounced interaction with the PHBV matrix, which yielded improvements in processing conditions and PHBV’s flexibility and impact properties.     

Organically Modified Nanoclay and Aluminum Hydroxide Incorporated Bionanocomposites towards Enhancement of Physico-mechanical and Thermal Properties of Lignocellulosic Structural Reinforcement

A range of bio-nanocomposites were prepared by incorporation of organo modified montmorillonite nanoclay (OMMT) with or without use of aluminum hydroxide (Al(OH)₃) within polylactic acid (PLA) solution. Furthermore, the solution was employed for modification of ligno-cellulosic (jute) fabric structural reinforcements. The successful incorporation of nanofillers within the host polymer, polylactic acid (PLA) was confirmed by Fourier-transform infrared spectroscopy (FT-IR). Water uptake and swelling behaviour studies revealed that the water uptake and swelling ratio of bio-composites reduced significantly as compared to pristine jute fabric, whereas upon incorporation of OMMT and Al(OH)₃, the water barrier properties reduced even further in the developed bio-nanocomposites. The flexural strength of the bio-nanocomposites also showed improved mechanical and dimensional stability. Synergistic effects of OMMT and Al(OH)₃ were observed in enhancing the aforementioned physico-mechanical properties. Scanning electron microscopy (SEM) studies revealed microstructural details of developed samples. Similarly, the thermo-gravimetric analysis and linear burning rate studies of Al(OH)₃ treated bio-nanocomposite materials revealed enhanced thermal resistance and reduced flammability respectively compared to both pristine woven jute fabric and fabrics treated with PLA alone or those without Al(OH)₃. From the above results it can safely be said that the bio-nanocomposite material can be a prospective candidate for development of flame retardant biopackaging.     

Fabrication and Characterization of PLA/PHBV-Chitin Nanocomposites and Their Foams

This paper examines the effect of biobased chitin nanowhisker fillers on the thermal, rheological, physical, mechanical and morphological properties of biobased polylactic acid (PLA) and PLA/polyhydroxybutyrate-co-valerate (PHBV) blended nanocomposites as well as the physical, mechanical and morphological properties of porous PLA and PLA/PHBV nanocomposite foams. Solid nanocomposites of PLA, PLA/PHBV and chitin nanowhiskers were manufactured through melt blending while porous nanocomposites foams were fabricated through a batch foaming process with the aid of CO₂ as blowing agent. It was found that by incorporating small quantities of chitin nanowhiskers (<2 wt%) the mechanical properties of solid specimens are improved while strength and expandability of the foam can be significantly improved, yielding a homogenously distributed cell morphology with average cell size of 1.5 μm.     

Degradation Study of Biobased Polyester–Polyurethane and its Nanocomposite Under Natural Soil Burial,UV Radiation and Hydrolytic-Salt Water Circumstances

The current study focuses on the development of a formulation of polyester polyurethane (PEPU) samples using castor oil (CO) modified polyester polyol and partially biobased aliphatic isocyanate. The CO modified polyester polyol was synthesized employing transesterification reaction between CO and diethylene glycol in the presence litharge (PbO) catalyst. Subsequently, the modification of CO was confirmed using proton nuclear magnetic resonance (¹HNMR) spectra analysis. In the next stage, the biobased polyester polyurethane nanocomposites (PEPUNC) were prepared by incorporating 3 wt% OMMT nanoclay within PEPU through in situ polymerization technique. The produced PEPU was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹HNMR spectra analysis. Further, the degradation properties of developed PEPU subjected to soil-burial, UV exposure and hydrolytic-salt water medium were noted by FTIR spectroscopy. Corresponding weight loss, mechanical measurements and morphological studies through scanning electron microscopy (SEM) analysis were studied. The results showed that the addition of OMMT nanoclay within the PEPU matrix produces significant improvement in the degradation rate which indicated the susceptibility of OMMT nanoclay to humidity upon exposure to soil burial. The produced microorganisms from the soil resulted in significant chemical and morphological changes in the entire structure of the PEPU. Additionally, the highest degradation and percentage of weight loss was observed under soil burial as compared to UV exposure and hydrolytic-salt water medium.     

Study on Biodegradable Starch/OMMT Nanocomposites for Packaging Applications

The thermoplastic starch (TPS) and nanocomposite(TPS/OMMT) was prepared with 15% carbamide, 15% ethanolamine and different contents of organic activated montmorillonite (OMMT) by twin-screw extruder with a 130 °C barrel temperature. Fourier transforms infrared spectroscopy and wide angle X-ray diffraction shown that the alkylamine in dodecyl benzyl dimethyl ammonium bromide could react with MMT via cation exchange reaction. After treated, the d(001)space distance of MMT increased from 1.5 to 1.7 nm. Scanning electron microscope revealed that the lower contents of OMMT could disperse well in the matrixes of TPS. The carbamide, ethanolamine and the OMMT could destroy the crystallization behavior of starch, but only the OMMT restrained this behavior for long-term storing. Mechanical properties investigation indicated that the tensile strength and modulus of TPS/OMMT nanocomposites were better than those of TPS, while the elongation at break was descended with the increasing of OMMT contents. When the content of OMMT was 4%, the tensile strength and modulus of TPS was improved from 4.2 and 42 MPa to 6.0 and 76 MPa, respectively.     

Assessment of Ball Milling as a Compounding Technique to Develop Nanocomposites of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate) and Bacterial Cellulose Nanowhiskers

The aim of this study was the assessment of high energy ball milling technique to develop poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) nanocomposites containing bacterial cellulose nanowhiskers (BCNW). Crystallization behaviour of PHBV/BCNW nanocomposites was studied under non-isothermal and isothermal conditions using differential scanning calorimetry. The changes in PHBV crystalline structure were also studied using X-ray diffraction. The results confirmed that BCNW acted as nucleating agents and, hence, favored the crystallization of the PHBV. The oxygen permeability of the nanocomposites was reduced by ~22 % when compared to that of the neat PHBV. This work provides a new insight into the development of polyhydroxyalkanoate composites by means of the high energy ball milling technique.     

Melt Compounded Blends of Short and Medium Chain-Length Poly-3-hydroxyalkanoates

Blends of poly-3-hydroxybutyrate with an elastomeric medium-chain-length poly-3-hydroxyalkanoate (MCL-PHA), containing 98 mol% 3-hydroxyoctanoate and 2 mol% 3-hydroxyhexanoate (referred to as PHO), were prepared by melt compounding. Coarsening of the droplet-matrix morphology of the blends was noted as the PHO content increased beyond 5 wt%; this was attributed to the significant viscosity mismatch between the components. Addition of PHO improved the thermal stability of the blends, reduced their crystallinity and resulted in shifts in their melting and crystallization temperatures. The blends had improved tensile strain at break. The unnotched impact strength showed a threefold increase at 30 wt% PHO content. Cross-linking of PHO using a peroxide initiator increased its viscosity, thus improving the morphology and mechanical properties of the blends.     

Improvement of Synthesis and Dielectric Properties of Polyurethane/Mt-QASs<Superscript>+</Superscript> (Novel Synthesis)

Polyurethane-based nanocomposites were prepared and their dielectric properties were characterized. Polyurethane (PU) composites were prepared with different organoclay content (1, 3, 5, and 10 wt% for all cases). The composites included quaternary ammonium salts such as 1-methyl-di-octyl-1 phenyl ammonium iodide (QAS-1), 1-methyl-di-nonyl-1 phenyl ammonium iodide (QAS-2), and 1-methyl-di-dodecyl-1 phenyl ammonium iodide (QAS-3) which were newly synthesized for modification of Na⁺-montmorillonite. Addition of aluminum silicate enhanced the dielectric properties at a constant concentration. Dielectric constants of nanocomposites compounded with 3 %- and 5 %-organoclay were close in value. The characterization of PU/organoclay composites was carried out using Fourier transform infrared and X-ray diffraction.     

Study of Thermo-Mechanical and Morphological Behaviour of Biodegradable PLA/PBAT/Layered Silicate Blend Nanocomposites

Poly (lactic acid) (PLA) and poly (butylene adipate-co-terephthalate) (PBAT) blend nanocomposites were prepared using melt blending technique followed by compression moulding. The blend nanocomposites were prepared with a variation of PBAT loading along with maleic anhydride and benzoyl peroxide ranging from 5 to 20 wt% along with two different commercially available nanoclays cloisite 93A and cloisite 30B (C30B) at 3 wt% loading. The maleic anhydride and benzoyl peroxide were used during the melt blending of the blend nanocomposites as a compatibilizer and as an accelerator respectively. Maleic anhydride used to enhance the compatibility of the PLA/PBAT blend and as well as the uniform adhesion of the nanoclays with them. The properties and characterizations of PLA matrix and the PLA/PBAT blend nanocomposites have been studied. The tensile strength, % elongation and impact strength increased with the preparation of PLA/PBAT blend nanocomposites as compared with PLA matrix. PLA/PBAT/C30B blend nanocomposites exhibited optimum tensile strength at 15 wt% of PBAT loading. Differential scanning calorimetry and thermogravimetric analysis also showed improved thermal properties as compared with virgin PLA. The wide angle X-ray diffraction studies indicated an increase in d-spacing in PLA/PBAT/C30B blend nanocomposite thus revealing intercalated morphology.     

Effect of Hexadecyl Lactate as Plasticizer on the Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide) Films for Food Packaging Applications

In this study, poly(l-lactide) (PLA) films were fabricated by melt processing and the plasticizing effect of hexadecyl lactate (HL) (0, 5, 7.5, 10, and 12.5 wt% on PLA were investigated by scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis, tensile, transparency, and water vapor permeability tests. The SEM analysis revealed that PLA with 10 wt% HL appeared uniform with extra small bumps, confirmed the interaction between PLA and HL. The thermal analysis revealed a glass transition temperature of 57.4 °C for neat PLA film, but the addition of HL elicited a decrease in the temperature of the peak (43.8 °C). The incorporation of plasticizer into PLA resulted in the increase of elongation at break, as well as the decrease of tensile strength and tensile modulus. Even though a decrease in transparency was recorded, the PLA/HL blend films appeared transparent by visually observation. The water vapor permeability of PLA/HL blend films increased with the increase of HL. The PLA/HL blend films could effectively extend the shelf-life of fresh-cut pears as the commercial low density polyethylene films. The results indicated that the properties of PLA films can be modified with the addition of HL and PLA/HL blend films could serve as an alternative as food packaging materials to reduce environmental problems associated with synthetic packaging films.     

Elaboration and Characterization of Nano-Biocomposites Based on Plasticized Poly(Hydroxybutyrate-Co-Hydroxyvalerate) with Organo-Modified Montmorillonite

Nano-biocomposites based on a biodegradable bacterial copolyester, poly(hydroxybutyrate-co-hydroxyvalerate), have been elaborated with an organo-modified montmorillonite (OMMT) clay as nanofiller, and acetyl tributyl citrate as plasticizer. The corresponding (nano)structures, thermal and mechanical properties, permeability, and biodegradability have been determined. Polyhydroxyalkanoates are very thermal sensitive then to follow the degradation the corresponding matrices have been analyzed by size exclusion chromatography. The results indicate that the addition of the plasticizer decreases the thermo-mechanical degradation, during the extrusion. These nano-biocomposites show an intercalated/exfoliated structure with good mechanical and barrier properties, and an appropriated biodegradation kinetic. Intending to understand the changes in the thermal properties, the nano-biocomposites were characterized by thermal gravimetric analysis and differential scanning calorimetry. The presence of the OMMT clay did not influence significantly the transition temperatures. However, the filler not only acted as a nucleating agent which enhanced the crystallization, but also as a thermal barrier, improving the thermal stability of the biopolymer. The results indicated that the addition of the plasticizer reduces the glass transition temperature and the crystalline melting temperature. The plasticizer acts as a processing aid and increases the processing temperature range (lower melting temperature).     

Effect of Nano-SiO<Subscript>2</Subscript> and Bark Flour Content on the Physical and Mechanical Properties of Wood–Plastic Composites

The aim of this study is to evaluate the impact of nano-SiO₂ and bark flour (BF) on the natural fiber–plastic composites engineering properties made from high density polyethylene (HDPE) and beech wood flour (WF). For this purpose, WF and BF in 60 mesh size and weight ratio of (50, 0 %), (30, 20 %), (10, 40 %) and (0, 50 %) respectively were mixed with HDPE. In order to increase the interfacial adhesion between the filler and the matrix, the maleic anhydride grafted polyethylene was constantly used at 3 wt% for all formulations as a coupling agent. The nano-SiO₂ particles with weight ratio of 0, 1, 2, and 4 % were also utilized to enhance the composites properties. The materials were mixed in an internal mixer (HAAKE) and then the bark and/or wood–plastic composite samples were made utilizing an injection molding machine. The physical tests including water absorption and thickness swelling, and mechanical tests including bending characteristics and un-notched impact strength were carried out on the samples based on ASTM standard. The results indicated that as the BF content increased in the composite, mechanical and physical properties were reduced, but the given properties were increased with the addition of nano-SiO₂. The addition of nano-SiO₂ had a negative impact on the physical properties, but when it was up to 2 %, it increased the impact strength.     

Thermocatalytic Degradation of High Density Polyethylene into Liquid Product

Thermocatalytic degradation of high density polyethylene (HDPE) was carried out using acid activated fire clay catalyst in a semi batch reactor. Thermal pyrolysis was performed in the temperature range of 420–500 °C. The liquid and gaseous yields were increased with increase in temperature. The liquid yield was obtained 30.1 wt% with thermal pyrolysis at temperature of 450 °C, which increased to 41.4 wt% with catalytic pyrolysis using acid activated fire clay catalyst at 10 wt% of catalyst loading. The composition of liquid products obtained by thermal and catalytic pyrolysis was analyzed by gas chromatography-mass spectrometry and compounds identified for catalytic pyrolysis were mainly paraffins and olefins with carbon number range of C₆–C₁₈. The boiling point was found in the range of commercial fuels (gasoline, diesel) and the calorific value was calculated to be 42 MJ/kg.     

Tensile and Combustion Properties of PP/IFR/POE/nano-CaCO<Subscript>3</Subscript> Composites

The tensile and combustion properties of polypropylene/polyolyaltha olefin composites filled with intumescent flame retardant (IFR) and nanometer calcium carbonate (nano-CaCO₃) were measured. It was found that the values of the Young’s modulus of the composites increased almost linearly, while the values of the tensile yield strength and tensile fracture strength of the composites decreased with increasing the IFR weight fraction; the values of the elongation at break of the composites decreased quickly when the IFR weight fraction was lower than 10 wt%, and then varied slightly when the IFR weight fraction was higher than 10 wt%. Moreover, the morphology of the specimens after combustion was observed and the frame retardant mechanisms of the composites were discussed.     

Characterization of Extruded Thermoplastic Starch Reinforced by Montmorillonite Nanoclay

The purpose of this study was to understand how the montmorillonite (MMT) nanoclay influences physical and mechanical properties of thermoplastic starch (TPS), which was produced by a conventional extrusion procedure. MMT nanoclay was added at 0, 4, and 8 % (w/w) concentrations. Transmission electron microscopy (TEM) showed most MMT platelets existed in tactoid structure in the starch matrix. In addition, FTIR spectra indicated TPS/MMT nanocomposites kept chemically stable after the extrusion. Tensile strength (TS) was about 7.0 MPa, while elongation-at-break (E) and elastic modulus (EM) were about 52 % and 32–41 MPa, respectively. Moisture sorption behaviour of the samples was well described by GAB and BET models. Thermal property tests exhibited the glass transition temperature (T _g ) of the nanocomposites decreased with increasing MMT from 0 to 8 %, indicating MMT nanoclay had a plasticization effect.     

Absorption characteristics of potassium carbonate-based solutions with rate promoters and corrosion inhibitors

In this research, absorbents for CO₂ capture were prepared by blending 30 wt% potassium carbonate, 3 wt% of a rate promoter, and 1 wt% of a corrosion inhibitor. Pipecolic acid, sarcosine, and diethanolamine were chosen as rate promoter candidates. Based on a rate promoter screening test for CO₂ loading capacity and absorption rate, pipecolic acid and sarcosine were selected to be used as rate promoters. 1,2,3-benzotriazole and ammonium thiocyanate were chosen as corrosion inhibitors, and they were mixed with a 30 wt% potassium carbonate-based absorbent mixture containing one of the rate promoters. The absorption rates for four absorbent solutions (30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% 1,2,3-benzotriazole, 30 wt% potassium carbonate?+?3 wt% pipecolic acid?+?1 wt% ammonium thiocyanate, 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% 1,2,3-benzotriazole, and 30 wt% potassium carbonate?+?3 wt% sarcosine?+?1 wt% ammonium thiocyanate) were measured, tabulated, and graphically displayed. These types of absorbents can be used for capturing CO₂ under high temperature and pressure conditions, such as those found in coal-fired power plants.     

Recovery of Nd and Dy from rare earth magnetic waste sludge by hydrometallurgical process

This paper describes a hydrometallurgical process for recovering neodymium (Nd) and dysprosium (Dy) from a magnetic waste sludge generated from the Nd–Fe–B(–Dy) manufacturing process. Phase analysis by XRD study revealed Nd(OH)₃ and Fe₂O₃ as main mineral phases, and chemical analysis by ICP showed the contents of 35.1 wt% Nd, 29.5 wt% Fe, 1.1 wt% Dy and 0.5 wt% B. A solution of 1 M HNO₃ + 0.3 M H₂O₂ was used to dissolve up to 98 % Nd and 81 % Dy, while keeping Fe dissolution below 15 % within 10 min. Fe dissolved in solution was completely removed as Fe(OH)₃ at pH 3 followed by precipitation of Nd and Dy with oxalic acid (H₂C₂O₄) and recovered 91.5 % of Nd and 81.8 % of Dy from solution. The precipitate containing Nd and Dy was calcined at 800 °C to obtain Nd₂O₃ as final product with 68 % purity, and final recovery of 69.7 % Nd and 51 % of Dy was reported in this process.     

Polylactide (PLA)—Halloysite Nanocomposites: Production, Morphology and Key-Properties

To evaluate the potential of halloysite nanotubes (HNT) as nanofiller for polylactide (PLA), various nanocomposites have been successfully produced by melt-blending the polyester matrix with HNT (HNT(QM)). HNT were also surface treated by silanization reaction with 3-(Trimethoxysilyl) propyl methacrylate (TMSPM). The morphology, thermal, tensile and impact strength properties of the nanocomposites containing 3?C12?% HNT were evaluated and compared to those of pristine (unfilled) PLA. The nanocomposites were characterized by higher rigidity (with Young??s modulus increasing with HNT loading), higher tensile strength (about 70?MPa at 6?% HNT(QM)), whereas the elongation at break and impact strength did not decrease. As demonstrated under dynamic solicitation (DMA), melt-blending PLA with HNT led to enhancement of storage modulus (E??) and offers the possibility to use PLA in applications requiring higher temperatures of utilization. However, with few exceptions, TGA and DSC measurements did not reveal important changes of thermal parameters. The surface silanization treatment proved to improve the quality of the nanofiller dispersion even at higher loading. As a result, good thermal stability associated to high tensile strength, and noticeable increases in impact properties were recorded. Furthermore, enhanced nucleating ability and crystallization kinetics of the PLA matrix were revealed as specific characteristics.     

Polyhydroxybutyrate-Based Nanocomposites with Cellulose Nanocrystals and Bacterial Cellulose

Polyhydroxybutyrate (PHB) films nanoreinforced with hydrolyzed cellulose nanocrystals (CNC) and bacterial cellulose (BC) were prepared by solvent casting. The influence of different cellulose nanoparticles content (2, 4 and 6 wt% of CNC and 2 wt% of BC) on the PHB properties was studied. CNC nanocomposites presented good dispersion of the nanocrystals, improving transparency, mechanical and barrier properties of the PHB films. On the other hand, reduced thermal stability and mechanical properties were yielded by BC addition due to the intrinsic lower degradation temperature and higher length of the BC nanofibrils compared to CNC. Nanocomposites performance variation is mainly caused by the marked difference in nanoparticles structure. It was demonstrated that PHB–CNC films exhibited higher performance enhancement without detrimental effect of the pristine PHB properties.     

Green Composites of Poly (Lactic Acid) and Sugarcane Bagasse Residues from Bio-refinery Processes

Twin-screw extrusion was used to prepare the composites consisting of PLA and three types of sugarcane bagasse residues (up to 30 wt%) derived from different steps of a biorefinery process. Each residue had different composition, particle size and surface reactivity due to chemical and biological (enzyme, microbes) treatments that the biomass was subjected to. The effects of different residue characteristics on properties, crystallization behaviors and morphologies of PLA composites were investigated. Besides, a small amount (2 wt%) of coupling agent, Desmodur^® VKS 20 (DVKS), was used to improve the interfacial bonding between PLA and bagasse residues. The results indicated that in the presence of 2 % DVKS, PLA composite with pretreated residue exhibited the maximum strength properties (98.94 % tensile strength and 93.91 % flexural strength of neat PLA), while PLA composite with fermentation residue exhibited the minimum strength properties (88.98 % tensile strength and 81.91 % flexural strength of neat PLA).