Characterization of municipal solid waste combustion in a grate furnace

The objective of this paper is to evaluate the combustion process of municipal solid waste combustion in a grate furnace both experimentally and numerically by using data of a reference experiment with over-stoichiometric primary air supply. Measurements were carried out inside the combustion chamber of a pilot plant by monitoring temperatures and sampling gaseous combustion products along the bed surface. The data were assessed using elemental and energy balances. Experimental data of the axial temperature profiles of the flue gas, the fuel bed and the grate bars, as well as local gas flows and the flue gas composition measured above the fuel bed along the grate were used to describe the conversion process, including drying and carbon burnout. These data served as input to model the thermo- and fluid dynamic processes of the gas phase above the bed inside the combustion chamber. For this purpose the commercial code FLUENT was employed to carry out the simulations. Thus, the turbulent temperature, flow and species distributions in the combustion chamber of the pilot waste incinerator TAMARA were predicted. The results of the FLUENT modeling showed that under the prevailing conditions the flue gas burnout is almost completed before entering the first flue due to high temperatures, effective mixing and sufficient residence times of the flue gas inside the combustion chamber. This agrees well with the experimental results inside the first flue. On the basis of the above mentioned results, design and parametric studies can be carried out in a more efficient way by saving cost and time.     

Pyrolysis of tyres. Influence of the final temperature of the process on emissions and the calorific value of the products recovered

A study was made of the pyrolysis of tyre particles, with the aim of determining the possibilities of using the products resulting from the process as fuel. Three final temperatures were used, determined from thermogravimetric data. The design of the experiment was a horizontal oven containing a reactor into which particles of the original tyre were placed. After the process, a solid fraction (char) remained in the reactor, while the gases generated went through a set of scrubbers where most of the condensable fraction (oils) was retained. Finally, once free of this fraction, the gases were collected in glass ampoules. Solid and liquids fractions were subjected to thermogravimetric analyses in order to study their combustibility. The gas fraction was analysed by means of gas chromatography to establish the content of CO, CO2, H2 and hydrocarbons present in the samples (mainly components of gases produced in the pyrolysis process). A special study was made of the sulphur and chlorine content of all the fractions, as the presence of these elements could be problematic if the products are used as fuel. Tyre pyrolysis engenders a solid carbon residue that concentrates sulphur and chorine, with a relatively high calorific value, although not so high as that of the original tyre. The liquid fraction produced by the process has a high calorific value, which rises with the final temperature, up to 40 MJ/kg. The chlorine content of this fraction is negligible. Over 95% of the gas fraction, regardless of the final temperature, is composed of hydrocarbons of a low molecular weight and hydrogen, this fraction also appearing to be free of chlorine.     

Gasification applicability study of polyurethane solid refuse fuel fabricated from electric waste by measuring syngas and nitrogenous pollutant gases

To recycle polyurethane foam waste generated from electric appliance recycling centers for use as fuel in a gasification process, polyurethane solid refuse fuel fabricated as pellets was analyzed for the characteristics of elemental composition, proximate analysis, heating value, and thermo-gravimetric testing. It has a high heating value of 29.06 MJ/kg with a high content of combustibles, which could be feasibly used in any thermal process. However, the nitrogen content, of up to 7 %, was comparably higher than for other fuels such as coal, biomass, and refuse-derived fuel, and may result in the emission of nitrogenous pollutant gases of HCN and NH₃. By conducting gasification experiments on polyurethane solid refuse fuel in a fixed-bed reactor, a syngas with a heating value of 9.76 kJ/m³ and high content of both H₂ and CO were produced with good gasification efficiency; carbon conversion 54 %, and cold gas efficiency 60 %. The nitrogenous pollutant gases in syngas were measured at the concentrations of 160 ppm hydrogen cyanide and 40 ppm ammonia, which may have to be reduced using proper cleaning technologies prior to the commercialization of gasification technology for polyurethane waste.     

Energy recovery from solid waste fuels using advanced gasification technology

Since the mid-1980s, TPS Termiska Processer AB has been working on the development of an atmospheric-pressure gasification process. A major aim at the start of this work was the generation of fuel gas from indigenous fuels to Sweden (i.e. biomass). As the economic climate changed and awareness of the damage to the environment caused by the use of fossil fuels in power generation equipment increased, the aim of the development work at TPS was changed to applying the process to heat and power generation from feedstocks such as biomass and solid wastes. Compared with modern waste incineration with heat recovery, the gasification process will permit an increase in electricity output of up to 50%. The gasification process being developed is based on an atmospheric-pressure circulating fluidised bed gasifier coupled to a tar-cracking vessel. The gas produced from this process is then cooled and cleaned in conventional equipment. The energy-rich gas produced is clean enough to be fired in a gas boiler (and, in the longer term, in an engine or gas turbine) without requiring extensive flue gas cleaning, as is normally required in conventional waste incineration plants. Producing clean fuel gas in this manner, which facilitates the use of efficient gas-fired boilers, means that overall plant electrical efficiencies of close to 30% can be achieved. TPS has performed a considerable amount of pilot plant testing on waste fuels in their gasification/gas cleaning pilot plant in Sweden. Two gasifiers of TPS design have been in operation in Grève-in-Chianti, Italy since 1992. This plant processes 200 tonnes of RDF (refuse-derived fuel) per day. It is planned that the complete TPS gasification process (including the complete fuel gas cleaning system) be demonstrated in several gas turbine-based biomass-fuelled power generating plants in different parts of the world. It is the aim of TPS to prove, at commercial scale, the technical feasibility and economic advantages of the gasification process when it is applied to solid waste fuels. This aim shall be achieved, in the short-term, by employing the cold clean product gas in a gas boiler and, in the longer-term, by firing the gas in engines and gas turbines. A study for a 90 MWth waste-fuelled co-generation plant in Sweden has shown that, already today, gasification of solid waste can compete economically with conventional incineration technologies.     

Energy from Waste – Clean,efficient, renewable: Transitions in combustion efficiency and NOx control

Traditionally EfW (Energy from Waste) plants apply a reciprocating grate to combust waste fuel. An integrated steam generator recovers the heat of combustion and converts it to steam for use in a steam turbine/generator set. This is followed by an array of flue gas cleaning technologies to meet regulatory limitations.Modern combustion applies a two-step method using primary air to fuel the combustion process on the grate. This generates a complex mixture of pyrolysis gases, combustion gases and unused combustion air. The post-combustion step in the first pass of the boiler above the grate is intended to “clean up” this mixture by oxidizing unburned gases with secondary air.This paper describes modifications to the combustion process to minimize exhaust gas volumes and the generation of noxious gases and thus improving the overall thermal efficiency of the EfW plant. The resulting process can be coupled with an innovative SNCR (Selective Non-Catalytic Reduction) technology to form a clean and efficient solid waste combustion system.Measurements immediately above the grate show that gas compositions along the grate vary from 10% CO, 5% H₂ and 0% O₂ to essentially unused “pure” air, in good agreement with results from a mathematical model. Introducing these diverse gas compositions to the post combustion process will overwhelm its ability to process all these gas fractions in an optimal manner. Inserting an intermediate step aimed at homogenizing the mixture above the grate has shown to significantly improve the quality of combustion, allowing for optimized process parameters. These measures also resulted in reduced formation of NO_x (nitrogenous oxides) due to a lower oxygen level at which the combustion process was run (2.6 vol% O_2, wet instead of 6.0 vol% O_2, wet).This reduction establishes optimal conditions for the DyNOR? (Dynamic NO_x Reduction) NO_x reduction process. This innovative SNCR technology is adapted to situations typically encountered in solid fuel combustion. DyNOR? measures temperature in small furnace segments and delivers the reducing reagent to the exact location where it is most effective. The DyNOR? distributor reacts precisely and dynamically to rapid changes in combustion conditions, resulting in very low NO_x emissions from the stack.     

PCDD/F in source-sorted waste fractions and emissions from their co-combustion with reed canary-grass

The dry combustible fraction of source-sorted household waste, including material that would otherwise be recycled, was mixed with the energy crop reed canary-grass (Phalaris arundinacea L.), and combusted as briquettes in 150 and 600 kW biofuel-boilers without advanced cleaning systems. The source-sorted waste was further sorted and characterized according to its material and chemical contents. The bulk of the waste's chlorine content came from the non-package plastic fraction, whereas 90-95% of summation operator PCDD/F (74-90% of WHO-TEQ) originated from the textile fraction. The sources of the dioxins in the waste fractions are discussed. The balance of dioxin levels was negative, i.e., the amounts of dioxins output in the flue gas were lower than those input in the fuel, except when there were operational disturbances in the combustion. In one of the combustion trials the total levels of dioxins in the flue-gas and ashes were also lower than the input levels. The use of additional cleaning equipment will be needed to ensure that emissions of dioxins and hydrochloric acid will be below legal limits.     

Characterization of char derived from various types of solid wastes from the standpoint of fuel recovery and pretreatment before landfilling

Carbonization is a kind of pyrolysis process to produce char from organic materials under an inert atmosphere. In this work, chars derived from various solid wastes were characterized from the standpoint of fuel recovery and pretreatment of waste before landfilling. Sixteen kinds of municipal and industrial solid wastes such as residential combustible wastes, non-combustible wastes, bulky wastes, construction and demolition wastes, auto shredder residue, and sludges were carbonized at 500 degrees C for 1h under nitrogen atmosphere. In order to evaluate the quality of char as fuel, proximate analysis and heating value were examined. The composition of raw waste had a significant influence on the quality of produced char. The higher the ratio of woody biomass in waste, the higher heating value of char produced. Moreover, an equation to estimate heating value of char was developed by using the weight fraction of fixed carbon and volatile matter in char. De-ashing and chlorine removal were performed to improve the quality of char. The pulverization and sieving method seems to be effective for separation of incombustibles such as metal rather than ash. Most char met a 0.5 wt% chlorine criterion for utilization as fuel in a shaft blast furnace after it was subjected to repeated water-washing. Carbonization could remove a considerable amount of organic matter from raw waste. In addition, the leaching of heavy metals such as chrome, cadmium, and lead appears to be significantly suppressed by carbonization regardless of the type of raw waste. From these results, carbonization could be considered as a pretreatment method for waste before landfilling, as well as for fuel recovery.     

Comparative analysis of hazardous household waste in two Mexican regions

Household hazardous waste (HHW) generation in two Mexican regions was examined, a northern region (bordering with the USA) and a central region. The aim of this work was to determine the dynamics of solid waste generation and to be able to compare the results of both regions, regarding consumption patterns and solid waste generation rates. In the northern region, household solid waste was analysed quantitatively. In order to perform this analysis, the population was categorized into three socioeconomic strata (lower, middle, upper). Waste characterization revealed the presence of products that give origin to household hazardous waste. In the northern region (Mexicali city), household hazardous waste comprised 3.7% of municipal solid waste, the largest categories in this fraction were home care products (29.2%), cleaning products (19.5%) and batteries and electronic equipment (15.7%). In the central region, HHW comprised 1.03% of municipal solid waste; the main categories in this fraction were represented by cleaning products (39%), self care products (27.3%), and insecticides (14.4%). In Mexicali, the socioeconomic study demonstrated that the production of HHW is independent of the income level. Furthermore, the composition of the solid waste stream in both regions suggested the influence of another set of variables such as local climate, migration patterns and marketing coverage. Further research is needed in order to establish the effect of low quantities of HHW upon the environment and public health.     

Comparison of coal/solid recovered fuel (SRF) with coal/refuse derived fuel (RDF) in a fluidized bed reactor

An experimental study was undertaken to compare the differences between municipal solid waste (MSW) derived solid recovered fuel (SRF) (complying with CEN standards) and refuse derived fuel (RDF). Both fuels were co-combusted with coal in a 50 kW fluidised bed combustor and the metal emissions were compared. Synthetic SRF was prepared in the laboratory by grinding major constituents of MSW such as paper, plastic, textile and wood. RDF was obtained from a local mechanical treatment plant. Heavy metal emissions in flue gas and ash samples from the (coal + 10% SRF) fuel mixture were found to be within the acceptable range and were generally lower than that obtained for coal + 10% RDF fuel mixture. The relative distribution of heavy metals in ash components and the flue gas stream shows the presence of a large fraction (up to 98%) of most of the metals in the ash (except Hg and As). Thermo-gravimetric (TG) analysis of SRF constituents was performed to understand the behaviour of fuel mixtures in the absence and presence of air. The results obtained from the experimental study will enhance the confidence of fuel users towards using MSW-derived SRF as an alternative fuel.     

Experimental investigation of wood combustion in a fixed bed with hot air

Waste combustion on a grate with energy recovery is an important pillar of municipal solid waste (MSW) management in the Netherlands. In MSW incinerators fresh waste stacked on a grate enters the combustion chamber, heats up by radiation from the flame above the layer and ignition occurs. Typically, the reaction zone starts at the top of the waste layer and propagates downwards, producing heat for drying and devolatilization of the fresh waste below it until the ignition front reaches the grate. The control of this process is mainly based on empiricism.MSW is a highly inhomogeneous fuel with continuous fluctuating moisture content, heating value and chemical composition. The resulting process fluctuations may cause process control difficulties, fouling and corrosion issues, extra maintenance, and unplanned stops. In the new concept the fuel layer is ignited by means of preheated air (T > 220 °C) from below without any external ignition source. As a result a combustion front will be formed close to the grate and will propagate upwards. That is why this approach is denoted by upward combustion.Experimental research has been carried out in a batch reactor with height of 4.55 m, an inner diameter of 200 mm and a fuel layer height up to 1 m. Due to a high quality two-layer insulation adiabatic conditions can be assumed. The primary air can be preheated up to 350 °C, and the secondary air is distributed via nozzles above the waste layer. During the experiments, temperatures along the height of the reactor, gas composition and total weight decrease are continuously monitored. The influence of the primary air speed, fuel moisture and inert content on the combustion characteristics (ignition rate, combustion rate, ignition front speed and temperature of the reaction zone) is evaluated.The upward combustion concept decouples the drying, devolatilization and burnout phase. In this way the moisture and inert content of the waste have almost no influence on the combustion process. In this paper an experimental comparison between conventional and reversed combustion is presented.     

Thermal valorization of footwear leather wastes in bubbling fluidized bed combustion

Transformation of hide (animal skins) into leather is a complicated process during which significant amounts of wastes are generated. Footwear is the sector that consumes the major part of leather (60%). Logically, this industry is producing the largest quantity of leather wastes. The objective of this work was to demonstrate the technical feasibility of fluidized bed technology to recover the energy from burning footwear leather wastes. Considering the characteristics of leather waste, especially the heating value (12.5-21 MJ/kg), it can be considered a fairly good fuel. Moreover, leather waste has suitable characteristics for combustion, e.g., high volatile matter (76.5%) and low ash content (5.2%). Two factors deserve special attention: N3O and NOx emissions as a consequence of its unusual high nitrogen content (14.1%) and the chromium speciation because chromium is the main element of ash (3.2%) due to its use in leather tanning. A series of experiments has been carried out in a 0.1 MWt bubbling fluidized bed pilot plant. The combustion efficiency, flue gas composition and chromium speciation were investigated. Despite having high nitrogen content, a low conversion rate of fuel-N to NOx and N2O was attained. Chromium was concentrated in the solid streams and it was consistently found as Cr(III+); no presence of Cr(VI+) was detected.     

Effects of flue gas composition on the catalytic destruction of chlorinated aromatic compounds with a V-oxide catalyst

When using catalytic flue gas cleaning, several flue gas compounds may influence oxidation reactions of hazardous volatile organic compounds, possibly leading to lower reaction rates and, thus, to an incomplete destruction. Experimental investigations were performed with regard to the influence of selected flue gas compounds, like hydrogen chloride, sulfur dioxide, oxygen, and water vapour, on the catalytic destruction behavior of chlorobenzenes under flue gas cleaning conditions of an incineration plant. For this purpose, a metal oxide catalyst was operated at different temperatures at a space velocity of 3600 h-1 in a laboratory-scale fixed bed reactor with model flue gases, and with real flue gases generated from the TAMARA waste incineration plant. The results obtained from the studies with model flue gas were analyzed with respect to reaction kinetics. These kinetics were applied for comparison with the experimental data gained in the real flue gas.     

Thermal conversion of municipal solid waste via hydrothermal carbonization: comparison of carbonization products to products from current waste management techniques

Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 °C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO(2)-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage).     

Steam gasification of tyre waste, poplar, and refuse-derived fuel: a comparative analysis

In the field of waste management, thermal disposal is a treatment option able to recover resources from "end of life" products. Pyrolysis and gasification are emerging thermal treatments that work under less drastic conditions in comparison with classic direct combustion, providing for reduced gaseous emissions of heavy metals. Moreover, they allow better recovery efficiency since the process by-products can be used as fuels (gas, oils), for both conventional (classic engines and heaters) and high efficiency apparatus (gas turbines and fuel cells), or alternatively as chemical sources or as raw materials for other processes. This paper presents a comparative study of a steam gasification process applied to three different waste types (refuse-derived fuel, poplar wood and scrap tyres), with the aim of comparing the corresponding yields and product compositions and exploring the most valuable uses of the by-products.     

Decreased PCDD/F formation when co-firing a waste fuel and biomass in a CFB boiler by addition of sulphates or municipal sewage sludge

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are formed during waste incineration and in waste-to-energy boilers. Incomplete combustion, too short residence times at low combustion temperatures (<700 °C), incineration of electronic waste and plastic waste containing chlorine are all factors influencing the formation of PCDD/Fs in boilers. The impact of chlorine and catalysing metals (such as copper and iron) in the fuel on PCDD/F formation was studied in a 12 MW_th circulating fluidised bed (CFB) boiler. The PCDD/F concentrations in the raw gas after the convection pass of the boiler and in the fly ashes were compared. The fuel types were a so-called clean biomass with low content of chlorine, biomass with enhanced content of chlorine from supply of PVC, and solid recovered fuel (SRF) which is a waste fuel containing higher concentrations of both chlorine, and catalysing metals. The PCDD/F formation increased for the biomass with enhanced chlorine content and it was significantly reduced in the raw gas as well as in the fly ashes by injection of ammonium sulphate. A link, the alkali chloride track, is demonstrated between the level of alkali chlorides in the gas phase, the chlorine content in the deposits in the convection pass and finally the PCDD/F formation. The formation of PCDD/Fs was also significantly reduced during co-combustion of SRF with municipal sewage sludge (MSS) compared to when SRF was fired without MSS as additional fuel.     

Combustion studies of high moisture content waste in a fluidised bed

The combustion of three high moisture content waste materials in a fluidised bed combustor has been investigated and a comparison with co-firing of these materials with coal in the same combustor has been made. Waste materials burnt were olive oil waste, municipal solid waste and potato, which is representative of vegetable waste. Mixtures of up to 20% mass concentration water in the waste were fed to the combustor. Above that value the moisture content was too high to sustain combustion without addition of coal. Measurements of CO, NOx, SO2 temperatures were made and the carbon combustion efficiency evaluated. Co-firing with coal resulted in markedly higher combustion efficiencies with an increase of approximately 10-80% when burning the simulated MSW. However, this was much lower than the value of 93% when coal was burnt on its own. It was also much lower than the value obtained, average 90%, when co-firing potato and olive oil waste with coal and there was little difference in the combustion efficiency between the two types of waste and with increasing moisture content. It was concluded that the high ash content of the simulated MSW 26%, compared with 5% in the other two waste materials resulted in slower burning and consequently the char particles were elutriated from the bed without being fully burnt. In term of gaseous emissions during co-combustion, CO emission is relatively insensitive to change in waste fraction. While emission of SO2 can be reduced as the waste fraction increases as a result of fuel-S dilution. But in terms of percent fuel-S converted, it is actually increased by increasing waste fraction. Emissions of NO and N2O increase slightly with MSW fraction.     

Pyrolysis of municipal plastic wastes II: Influence of raw material composition under catalytic conditions

In this work, the results obtained in catalytic pyrolysis of three plastic waste streams which are the rejects of an industrial packing wastes sorting plant are presented. The samples have been pyrolysed in a 3.5 dm(3) reactor under semi-batch conditions at 440 °C for 30 min in nitrogen atmosphere. Commercial ZSM-5 zeolite has been used as catalyst in liquid phase contact. In every case, high HHV gases and liquids which can be useful as fuels or source of chemicals are obtained. A solid fraction composed of the inorganic material contained in the raw materials and some char formed in the pyrolysis process is also obtained. The zeolite has shown to be very effective to produce liquids with great aromatics content and C3-C4 fraction rich gases, even though the raw material was mainly composed of polyolefins. The characteristics of the pyrolysis products as well as the effect of the catalyst vary depending on the composition of the raw material. When paper rich samples are pyrolysed, ZSM-5 zeolite increases water production and reduces CO and CO(2) generation. If stepwise pyrolysis is applied to such sample, the aqueous liquid phase can be separated from the organic liquid fraction in a first low temperature step.     

Evaluation of an organic soil amendment generated from municipal solid waste seeded with activated sewage sludge

This study investigated the feasibility of using fresh activated sewage sludge as inoculum for the microbial valorization of segregated municipal solid waste and evaluated the quality of organic soil amendment generated. Organic fraction of municipal solid waste, which consisted of vegetative (vegetable, fruit and flower) wastes was seeded with activated sewage sludge and processed by rapid aerobic microbial treatment. Efficacy of microbial valorization process and quality of final product were assessed by physico-chemical analysis. Suitability of final product was assessed with regard to heavy metal content, pesticide residues, microbiological quality and phytotoxicity. Quality of the soil amendment generated was compared with the control product generated with a commercial microbial inoculum. Phytotoxicity experiments indicated the stimulatory effect of sewage sludge seeded soil amendment on plant growth but inhibition was observed in closed growth test due to the evolution of gaseous phytotoxic agents. The study suggests that segregated municipal solid waste can be effectively valorized with activated non-dewatered sewage sludge as inoculum and the quality of soil amendment generated was comparable to compost intended for unrestricted applications.     

Laboratory scale studies on gaseous emissions generated by the incineration of an artificial automotive shredder residue presenting a critical composition

Car manufacturers must eliminate automotive shredder residues (ASR). Two ways of incineration are of interest: at 850°C in municipal waste incinerators or at higher temperatures, above 1100°C in cement plants. These processes reduce the mass and the volume of waste to be disposed of in landfills and energy recovery might be possible. Regulations govern the emission of gaseous effluents to control environmental risk. To determine gaseous effluents from a pilot sacle or an industrial incineration plant, an artificial ASR was made by mixing three representative organic polymers present in the real ASR, namely polyvinylchloride, polyurethane and rubber. This mixture was incinerated at 850 and 1100°C in laboratory experiments and the analyses of the principal gaseous effluents such as carbon oxides, nitrogen oxides, volatile organic compounds, hydrochloric and hydrocyanic acids and sulphur compounds are presented and discussed. Lastly, in order to simulate artificial ASR behaviour, the composition of the combustion gases at equilibrium was calculated using a Gibbs energy minimisation code.     

Comparing the greenhouse gas emissions from three alternative waste combustion concepts

Three alternative condensing mode power and combined heat and power (CHP) waste-to-energy concepts were compared in terms of their impacts on the greenhouse gas (GHG) emissions from a heat and power generation system. The concepts included (i) grate, (ii) bubbling fluidised bed (BFB) and (iii) circulating fluidised bed (CFB) combustion of waste. The BFB and CFB take advantage of advanced combustion technology which enabled them to reach electric efficiency up to 35% and 41% in condensing mode, respectively, whereas 28% (based on the lower heating value) was applied for the grate fired unit. A simple energy system model was applied in calculating the GHG emissions in different scenarios where coal or natural gas was substituted in power generation and mix of fuel oil and natural gas in heat generation by waste combustion. Landfilling and waste transportation were not considered in the model. GHG emissions were reduced significantly in all of the considered scenarios where the waste combustion concepts substituted coal based power generation. With the exception of condensing mode grate incinerator the different waste combustion scenarios resulted approximately in 1 Mton of fossil CO₂-eq. emission reduction per 1 Mton of municipal solid waste (MSW) incinerated. When natural gas based power generation was substituted by electricity from the waste combustion significant GHG emission reductions were not achieved.