Greenhouse gases emission from municipal waste management: The role of separate collection

The municipal solid waste management significantly contributes to the emission in the atmosphere of greenhouse gases (e.g. CO₂, CH₄, N₂O) and therefore the management process from collection to treatment and disposal has to be optimized in order to reduce these emissions. In this paper, starting from the average composition of undifferentiated municipal solid waste in Italy, the effect of separate collection on greenhouse gases emissions from municipal waste management has been assessed. Different combinations of separate collection scenarios and disposal options (i.e. landfilling and incineration) have been considered. The effect of energy recovery from waste both in landfills and incinerators has also been addressed. The results outline how a separate collection approach can have a significant effect on the emission of greenhouse gases and how wise municipal solid waste management, implying the adoption of Best Available Technologies (i.e. biogas recovery and exploitation system in landfills and energy recovery system in Waste to Energy plants), can not only significantly reduce greenhouse gases emissions but, in certain cases, can also make the overall process a carbon sink. Moreover it has been shown that separate collection of plastic is a major issue when dealing with global warming relevant emissions from municipal solid waste management.     

Using liquid waste streams as the moisture source during the hydrothermal carbonization of municipal solid wastes

Hydrothermal carbonization (HTC) is a thermal conversion process that can be an environmentally beneficial approach for the conversion of municipal solid wastes to value-added products. The influence of using activated sludge and landfill leachate as initial moisture sources during the carbonization of paper, food waste and yard waste over time at 250 °C was evaluated. Results from batch experiments indicate that the use of activated sludge and landfill leachate are acceptable alternative supplemental liquid sources, ultimately imparting minimal impact on carbonization product characteristics and yields. Regression results indicate that the initial carbon content of the feedstock is more influential than any of the characteristics of the initial liquid source and is statistically significant when describing the relationship associated with all evaluated carbonization products. Initial liquid-phase characteristics are only statistically significant when describing the solids energy content and the mass of carbon in the gas-phase. The use of these alternative liquid sources has the potential to greatly increase the sustainability of the carbonization process. A life cycle assessment is required to quantify the benefits associated with using these alternative liquid sources.     

Evaluation of carbonization as a thermal pretreatment method for landfilling by column leaching tests

To evaluate carbonization as a thermal pretreatment method for landfilling, the releasing characteristics of organic and inorganic constituents from carbonization residue derived from shredded residue of bulky waste was investigated by means of batch and column leaching tests. Shredded residue of bulky waste itself and its incineration ash were tested together to compare pretreatment methods. In batch leaching tests at a liquid/solid ratio of 10, the release of organic carbon from carbonization residue was at a remarkably low level. Besides, carbonization contributed to immobilize heavy metals such as chromium, cadmium, and lead within its residue. In column tests, the discharges of organic constituents were lowest from carbonization residue under aerobic conditions due to microbial activity. The leaching of Cd, Cr, Pb, and Cu from carbonization residue was suppressed under anaerobic conditions; however, this suppression effect tended to be weaker under aerobic conditions. From the results showing that the total releasing amounts of organic and inorganic constituents from carbonization residue are so low as to be comparable to that of incineration ash, carbonization can be considered as one of the thermal pretreatment methods of organic wastes.     

Survey of carbonization facilities for municipal solid waste treatment in Japan

The operations of carbonization facilities for municipal solid waste treatment in Japan were examined. Input waste, system processes, material flows, quality of char and its utilization, fuel and chemical consumption, control of facility emissions, and trouble areas in facility operation were investigated and analyzed. Although carbonization is a technically available thermochemical conversion method for municipal solid waste treatment, problems of energy efficiency and char utilization must be solved for carbonization to be competitive. Possible solutions include (1) optimizing the composition of input waste, treatment scale, organization of unit processes, operational methods, and quality and yield of char on the basis of analysis and feedback of long-term operating data of present operating facilities and (2) securing stable char demands by linking with local industries such as thermal electric power companies, iron manufacturing plants, and cement production plants.     

The environmental comparison of landfilling vs. incineration of MSW accounting for waste diversion

This study evaluates the environmental performance and discounted costs of the incineration and landfilling of municipal solid waste that is ready for the final disposal while accounting for existing waste diversion initiatives, using the life cycle assessment (LCA) methodology. Parameters such as changing waste generation quantities, diversion rates and waste composition were also considered. Two scenarios were assessed in this study on how to treat the waste that remains after diversion. The first scenario is the status quo, where the entire residual waste was landfilled whereas in the second scenario approximately 50% of the residual waste was incinerated while the remainder is landfilled. Electricity was produced in each scenario. Data from the City of Toronto was used to undertake this study. Results showed that the waste diversion initiatives were more effective in reducing the organic portion of the waste, in turn, reducing the net electricity production of the landfill while increasing the net electricity production of the incinerator. Therefore, the scenario that incorporated incineration performed better environmentally and contributed overall to a significant reduction in greenhouse gas emissions because of the displacement of power plant emissions; however, at a noticeably higher cost. Although landfilling proves to be the better financial option, it is for the shorter term. The landfill option would require the need of a replacement landfill much sooner. The financial and environmental effects of this expenditure have yet to be considered.     

Life-cycle greenhouse gas emissions and economic analysis of alternative treatments of solid waste from city markets in Vietnam

We utilize life cycle assessment to trace conversion of degradable organic carbon (DOC) contained in organic waste from city markets in Da Nang, Vietnam. Our methodology makes explicit the process of conversion of DOC under aerobic and anaerobic conditions, as well as the balance of nutrients. Greenhouse gas emissions were calculated for six alternative scenarios: (i) anaerobic landfilling (current situation); (ii) semi-aerobic landfilling; (iii) landfill gas capture; (iv) composting; (v) pre-composting before landfill; and (vi) biogas production. We calculate that 1 t of waste in anaerobic landfilling emits 1.70 t CO₂-eq. with life-cycle perspective. Lowest emission occurs in biogas scenario with 0.26 t CO₂-eq./t. Composting occupies an intermediate position with 0.39 t CO₂-eq./t. Likewise, we estimate that cost of emission reduction in solid waste sector of Vietnam is 15.13 US$/t CO₂-eq., given by alternative of composting and taking anaerobic landfilling as reference. On the other hand, if social cost of carbon (SCC) is incorporated lowest cost to treat 1 t of waste is given by composting and semi-aerobic landfilling at discount rate of 5 %. However, using lower discount rates, and consequently higher values of SCC, composting and biogas production become the alternatives with lowest treatment costs.     

A holistic life cycle analysis of waste management scenarios at increasing source segregation intensity: The case of an Italian urban area

Life cycle analysis of several waste management scenarios for an Italian urban area was performed on the basis of different source segregation collection (SS) intensities from 0% up to 52%. Source segregated waste was recycled and or/recovered by composting. Residual waste management options were by landfilling, incineration with energy recovery or solid recovered fuel (SRF) production to substitute for coal. The increase in fuel and materials consumption due to increase in SS had negligible influence on the environmental impact of the system. Recycling operations such as incineration and SRF were always advantageous for impact reduction. There was lower impact for an SS of 52% even though the difference with the SS intensity of 35% was quite limited, about 15%. In all the configurations analyzed, the best environmental performance was achieved for the management system producing SRF by the biodrying process.     

Gasification applicability study of polyurethane solid refuse fuel fabricated from electric waste by measuring syngas and nitrogenous pollutant gases

To recycle polyurethane foam waste generated from electric appliance recycling centers for use as fuel in a gasification process, polyurethane solid refuse fuel fabricated as pellets was analyzed for the characteristics of elemental composition, proximate analysis, heating value, and thermo-gravimetric testing. It has a high heating value of 29.06 MJ/kg with a high content of combustibles, which could be feasibly used in any thermal process. However, the nitrogen content, of up to 7 %, was comparably higher than for other fuels such as coal, biomass, and refuse-derived fuel, and may result in the emission of nitrogenous pollutant gases of HCN and NH₃. By conducting gasification experiments on polyurethane solid refuse fuel in a fixed-bed reactor, a syngas with a heating value of 9.76 kJ/m³ and high content of both H₂ and CO were produced with good gasification efficiency; carbon conversion 54 %, and cold gas efficiency 60 %. The nitrogenous pollutant gases in syngas were measured at the concentrations of 160 ppm hydrogen cyanide and 40 ppm ammonia, which may have to be reduced using proper cleaning technologies prior to the commercialization of gasification technology for polyurethane waste.     

Hydrothermal carbonization of food waste and associated packaging materials for energy source generation

Hydrothermal carbonization (HTC) is a thermal conversion technique that converts food wastes and associated packaging materials to a valuable, energy-rich resource. Food waste collected from local restaurants was carbonized over time at different temperatures (225, 250 and 275 °C) and solids concentrations to determine how process conditions influence carbonization product properties and composition. Experiments were also conducted to determine the influence of packaging material on food waste carbonization. Results indicate the majority of initial carbon remains integrated within the solid-phase at the solids concentrations and reaction temperatures evaluated. Initial solids concentration influences carbon distribution because of increased compound solubilization, while changes in reaction temperature imparted little change on carbon distribution. The presence of packaging materials significantly influences the energy content of the recovered solids. As the proportion of packaging materials increase, the energy content of recovered solids decreases because of the low energetic retention associated with the packaging materials. HTC results in net positive energy balances at all conditions, except at a 5% (dry wt.) solids concentration. Carbonization of food waste and associated packaging materials also results in net positive balances, but energy needs for solids post-processing are significant. Advantages associated with carbonization are not fully realized when only evaluating process energetics. A more detailed life cycle assessment is needed for a more complete comparison of processes.     

Life cycle assessment of the waste hierarchy--a Danish case study on waste paper

The waste hierarchy is being widely discussed these days, not only by cost-benefit analysts, but a growing number of life cycle assessments (LCA) have also begun to question it. In this article, we investigate the handling of waste paper in Denmark and compare the present situation with scenarios of more waste being recycled, incinerated or consigned to landfill. The investigations are made in accordance with ISO 14040-43 and based on the newly launched methodology of consequential LCA and following the recent guidelines of the European Centre on Waste and Material Flows. The LCA concerns the Danish consumption of paper in 1999, totalling 1.2 million tons. The results of the investigation indicate that the waste hierarchy is reliable; from an environmental point of view recycling of paper is better than incineration and landfilling. For incineration, the reason for the advantage of landfilling mainly comes from the substitution of fossil fuels, when incinerators provide heat and electricity. For recycling, the advantage is related to the saved wood resources, which can be used for generating energy from wood, i.e., from renewable fuel which does not contribute to global warming.     

The use of chemical composition data in waste management planning--a case study

As the waste industry continues to move from a disposal-based system to one based on a combination of recovery options, the need for information on the composition of waste increases and this is reflected by the amount of information on the physical composition of municipal solid wastes that is now available. However, there is far less information on the chemical composition of municipal solid waste. The results from a number of chemical surveys from Europe are compared and show a reasonable degree of agreement, but several problems were identified with the data. Chemical and physical compositional data are combined in a case study example to investigate the flow of key potential pollutants in an integrated solid waste management system that uses materials recycling, composting, incineration and landfilling. This case study has shown that an integrated waste management strategy diverts lead and cadmium away from composting and recycling to incineration, which effectively isolates these elements from the environment through efficient capture of the pollutants followed by secure landfilling or recycling of the residues. However, further work is needed to determine the distribution of mercury in incineration residues and its fate when the residues are landfilled.     

European Union waste management strategy and the importance of biogenic waste

In the European Union (EU), waste management is almost totally regulated by EU directives, which supply a framework for national regulations. The main target in view of sustainability is the prevention of direct disposal of reactive waste in landfills. The tools to comply with these principles are recycling and material recovery as well as waste incineration with energy recovery for final inertization. The adaptation of the principles laid down in EU directives is an ongoing process. A number of countries have already enacted respective national regulations and their realization shows that recycling and incineration are not in competition but are both essential parts of integrated waste management systems. In the EU, the amount of residual waste available for energy recovery can supply approximately 1% of the primary energy demand. About 50% of the energy inventory of municipal solid waste (MSW) in most EU countries is of biogenic origin, and MSW is to the same extent to be looked upon as regenerative fuel. Hence part of the CO₂ released from waste incineration is climate neutral. In the EU, this share could produce savings of the order of 1% of annual CO₂ emissions if energy from MSW replaced that derived from fossil fuel.     

The estimation of N2O emissions from municipal solid waste incineration facilities: The Korea case

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO₂), methane (CH₄), and nitrous oxide (N₂O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions.This study is designed to estimate the N₂O emission factors from MSW incineration plants, and calculate the N₂O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N₂O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment.The average of the N₂O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153 g-N₂O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N₂O emissions from MSW incineration comprised 19% of the total N₂O emissions.     

Economic assessment and energy model scenarios of municipal solid waste incineration and gas turbine hybrid dual-fueled cycles in Thailand

Finding environmentally benign methods related to sound municipal solid waste (MSW) management is of highest priority in Southeast Asia. It is very important to study new approaches which can reduce waste generation and simultaneously enhance energy recovery. One concrete example of particular significance is the concept of hybrid dual-fuel power plants featuring MSW and another high-quality fuel like natural gas. The hybrid dual-fuel cycles provide significantly higher electrical efficiencies than a composite of separate single-fuel power plant (standalone gas turbine combined cycle and MSW incineration). Although hybrid versions are of great importance for energy conversion from MSW, an economic assessment of these systems must be addressed for a realistic appraisal of these technologies. This paper aims to further examine an economic assessment and energy model analysis of different conversion technologies. Energy models are developed to further refine the expected potential of MSW incineration with regards to energy recovery and environmental issues. Results show that MSW incineration can play role for greenhouse gas reduction, energy recovery and waste management. In Bangkok, the electric power production via conventional incineration and hybrid power plants can cover 2.5% and 8% of total electricity consumption, respectively. The hybrid power plants have a relative short payback period (5 years) and can further reduce the CO₂ levels by 3% in comparison with current thermal power plants.     

The impact of municipal solid waste treatment methods on greenhouse gas emissions in Lahore, Pakistan

The contribution of existing municipal solid waste management to emission of greenhouse gases and the alternative scenarios to reduce emissions were analyzed for Data Ganj Bukhsh Town (DGBT) in Lahore, Pakistan using the life cycle assessment methodology. DGBT has a population of 1,624,169 people living in 232,024 dwellings. Total waste generated is 500,000 tons per year with an average per capita rate of 0.84kg per day. Alternative scenarios were developed and evaluated according to the environmental, economic, and social atmosphere of the study area. Solid waste management options considered include the collection and transportation of waste, collection of recyclables with single and mixed material bank container systems (SMBCS, MMBCS), material recovery facilities (MRF), composting, biogasification and landfilling. A life cycle inventory (LCI) of the six scenarios along with the baseline scenario was completed; this helped to quantify the CO2 equivalents, emitted and avoided, for energy consumption, production, fuel consumption, and methane (CH4) emissions. LCI results showed that the contribution of the baseline scenario to the global warming potential as CO2 equivalents was a maximum of 838,116 tons. The sixth scenario had a maximum reduction of GHG emissions in terms of CO2 equivalents of -33,773 tons, but the most workable scenario for the current situation in the study area is scenario 5. It saves 25% in CO2 equivalents compared to the baseline scenario.     

Process control in municipal solid waste incinerators: survey and assessment.

As there is only rare and scattered published information about the process control in industrial incineration facilities for municipal solid waste (MSW), a survey of the literature has been supplemented by a number of waste incineration site visits in Belgium and The Netherlands, in order to make a realistic assessment of the current status of technology in the area. Owing to the commercial character, and therefore, the confidentiality restrictions imposed by plant builders and many of the operators, much of the information collected has either to be presented in a generalized manner, and in any case anonymously. The survey was focused on four major issues: process control strategy, process control systems, monitors used for process control and finally the correlation between the 850 degrees C/2 s rule in the European waste incineration directive and integrated process control. The process control strategies range from reaching good and stable emissions at the stack to stabilizing and maximizing the energy output from the process. The main indicator to be monitored, in cases in which the focus is controlling emissions, is the oxygen content in the stack. Keeping the oxygen concentration in a determined range (usually between 8 and 12 vol.%) ensures stable and tolerated concentrations of the gaseous emissions. In the case for which stabilization of energy production is the principal aim, the main controlled parameter is the steam temperature and flow-rate, which is usually related to the fuel energetic input. A lot of other parameters are used as alarm criteria, the most common of which is the carbon monoxide concentration. The process control systems used most commonly feature partially automated classical proportional integral derivative (PID) controllers. New and innovative process control systems, such as fuzzy-logic control systems, are still unknown to most plant managers while their performance is reported to be unsatisfactory in plants in which such systems have been tested or are in use. Monitoring components used in process control are still based on classical tools such as thermocouples. The use of modern and more reliable sensors is very limited due to the high initial investment cost or simply the fear of using non-standard technologies. Complying with the 850 degrees C/2 s rule in the European waste incineration directive generally is seen to be a handicap for the process control, either in terms of cost, or flexibility of reaction, or both, particularly in old incineration facilities where such restrictions were not planned in the design.     

Mitigation of global greenhouse gas emissions from waste: conclusions and strategies from the Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report. Working Group III (Mitigation).

Greenhouse gas (GHG) emissions from post-consumer waste and wastewater are a small contributor (about 3%) to total global anthropogenic GHG emissions. Emissions for 2004-2005 totalled 1.4 Gt CO2-eq year(-1) relative to total emissions from all sectors of 49 Gt CO2-eq year(-1) [including carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), and F-gases normalized according to their 100-year global warming potentials (GWP)]. The CH4 from landfills and wastewater collectively accounted for about 90% of waste sector emissions, or about 18% of global anthropogenic methane emissions (which were about 14% of the global total in 2004). Wastewater N2O and CO2 from the incineration of waste containing fossil carbon (plastics; synthetic textiles) are minor sources. Due to the wide range of mature technologies that can mitigate GHG emissions from waste and provide public health, environmental protection, and sustainable development co-benefits, existing waste management practices can provide effective mitigation of GHG emissions from this sector. Current mitigation technologies include landfill gas recovery, improved landfill practices, and engineered wastewater management. In addition, significant GHG generation is avoided through controlled composting, state-of-the-art incineration, and expanded sanitation coverage. Reduced waste generation and the exploitation of energy from waste (landfill gas, incineration, anaerobic digester biogas) produce an indirect reduction of GHG emissions through the conservation of raw materials, improved energy and resource efficiency, and fossil fuel avoidance. Flexible strategies and financial incentives can expand waste management options to achieve GHG mitigation goals; local technology decisions are influenced by a variety of factors such as waste quantity and characteristics, cost and financing issues, infrastructure requirements including available land area, collection and transport considerations, and regulatory constraints. Existing studies on mitigation potentials and costs for the waste sector tend to focus on landfill CH4 as the baseline. The commercial recovery of landfill CH4 as a source of renewable energy has been practised at full scale since 1975 and currently exceeds 105 Mt CO2-eq year(-1). Although landfill CH4 emissions from developed countries have been largely stabilized, emissions from developing countries are increasing as more controlled (anaerobic) landfilling practices are implemented; these emissions could be reduced by accelerating the introduction of engineered gas recovery, increasing rates of waste minimization and recycling, and implementing alternative waste management strategies provided they are affordable, effective, and sustainable. Aided by Kyoto mechanisms such as the Clean Development Mechanism (CDM) and Joint Implementation (JI), the total global economic mitigation potential for reducing waste sector emissions in 2030 is estimated to be > 1000 Mt CO2-eq (or 70% of estimated emissions) at costs below 100 US$ t(-1) CO2-eq year(-1). An estimated 20-30% of projected emissions for 2030 can be reduced at negative cost and 30-50% at costs < 20 US$ t(-) CO2-eq year(-1). As landfills produce CH4 for several decades, incineration and composting are complementary mitigation measures to landfill gas recovery in the short- to medium-term--at the present time, there are > 130 Mt waste year(-1) incinerated at more than 600 plants. Current uncertainties with respect to emissions and mitigation potentials could be reduced by more consistent national definitions, coordinated international data collection, standardized data analysis, field validation of models, and consistent application of life-cycle assessment tools inclusive of fossil fuel offsets.     

Washing of waste prior to landfilling

The main impact produced by landfills is represented by the release of leachate emissions. Waste washing treatment has been investigated to evaluate its efficiency in reducing the waste leaching fraction prior to landfilling. The results of laboratory-scale washing tests applied to several significant residues from integrated management of solid waste are presented in this study, specifically: non-recyclable plastics from source separation, mechanical-biological treated municipal solid waste and a special waste, automotive shredded residues. Results obtained demonstrate that washing treatment contributes towards combating the environmental impacts of raw wastes. Accordingly, a leachate production model was applied, leading to the consideration that the concentrations of chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN), parameters of fundamental importance in the characterization of landfill leachate, from a landfill containing washed wastes, are comparable to those that would only be reached between 90 and 220years later in the presence of raw wastes. The findings obtained demonstrated that washing of waste may represent an effective means of reducing the leachable fraction resulting in a consequent decrease in landfill emissions. Further studies on pilot scale are needed to assess the potential for full-scale application of this treatment.     

Combustion characteristics of Malaysian municipal solid waste and predictions of air flow in a rotary kiln incinerator

Malaysia is in dire need of alternatives to landfilling for solid waste management. Recently, landfills have faced the problems of overfilling, overflowing of leachates leading to pollution of water resources, and uncontrolled dust emissions adversely affecting the local environment. With the rising cost of urbanization coupled with the high rate of waste generation, one possible method of waste treatment that is receiving particular attention by the government is incineration. Incineration of solid waste is rather new in Malaysia, with limited usage in handling small sources of waste generation such as the municipal solid waste (MSW) of resort islands; however, its potential in ameliorating the problems associated with solid waste treatment may make it an attractive alternative to landfill. This article presents the results of test runs conducted to investigate the performance of a locally designed and manufactured rotary kiln incinerator (RKI). The test runs were conducted using MSW collected from the Shah Alam municipality. The combustion efficiency was analyzed by looking at the temperature profiles and chemical species concentrations. To complement the combustion characteristics measurements, predictions of the air flow in the incinerator during the process were also investigated. The overall performance of the RKI suggests that it is suitable for treating MSW.     

Effect of mixing ratio of woody waste and food waste on the characteristics of carbonization residue

Biomass such as woody waste and food waste can be converted to a renewable energy source by means of carbonization processes. The basic characteristics of woody waste and food waste, such as proximate analysis and heating value, were evaluated before carrying out carbonization tests. Carbonization tests were carried out to obtain the basic characteristics of carbonization residue on changing the proportion of food waste from 0% to 30% in the mixture of woody waste and food waste. The effect of the food waste was estimated by basic characteristics of the residue such as the heating value, yield, and fuel ratio. As increased the food waste content, the bulk density, yield and chlorine content of the carbonization residue increased, but fuel ratio, the carbon content and heating value of the residue decreased. From the results of the basic characteristics of the residue, the optimum food waste content in carbonization tests was found to be 20%. Even if food waste is combined with woody waste at levels up to 30%, the sulfur and chlorine concentrations in the residue were much lower than the regulatory standard levels. From the results for the fuel ratio and heating value of the residue, the carbonization residue is suitable for use as a renewable energy source and can be categorized by the second grade level of solid fuel products.