Environmental evaluation of municipal waste prevention

Waste prevention has been addressed in the literature in terms of the social and behavioural aspects, but very little quantitative assessment exists of the environmental benefits. Our study evaluates the environmental consequences of waste prevention on waste management systems and on the wider society, using life-cycle thinking. The partial prevention of unsolicited mail, beverage packaging and food waste is tested for a "High-tech" waste management system relying on high energy and material recovery and for a "Low-tech" waste management system with less recycling and relying on landfilling. Prevention of 13% of the waste mass entering the waste management system generates a reduction of loads and savings in the waste management system for the different impacts categories; 45% net reduction for nutrient enrichment and 12% reduction for global warming potential. When expanding our system and including avoided production incurred by the prevention measures, large savings are observed (15-fold improvement for nutrient enrichment and 2-fold for global warming potential). Prevention of food waste has the highest environmental impact saving. Prevention generates relatively higher overall relative benefit for "Low-tech" systems depending on landfilling. The paper provides clear evidence of the environmental benefits of waste prevention and has specific relevance in climate change mitigation.     

燃煤电厂砷排放控制技术研究进展

对煤中砷的赋存状态及煤在燃烧后砷的转化行为进行了分析,并分别从煤的物理洗选、抑制煤中砷元素的挥发、气态砷吸附剂和污控设备协同脱砷等方面,重点论述了国内外对燃煤电厂砷排放控制的最新研究进展。同时提出了控制砷排放的新思路,为今后脱砷技术的进一步研究指明了方向。     

Investigating the Uncertainties in the Simple Mass Balance Equation for Acidity Critical Loads for Terrestrial Ecosystems in the United Kingdom

The Simple Mass Balance (SMB)equation has been developed and used as one ofthe principal methods for calculating criticalloads of acidity for forest ecosystems. Criticalloads have formed the basis for informing policyrelated to the control and abatement of emissionsof acidifying pollutants. The SMB equationrelies on a variety of assumptions and dataderived from a variety of sources. Each of thesecomponent constituents has a potential source oferror depending on the method(s) used for theirderivation and the value(s) assigned. The resultis the possibility of generating a range ofcritical load values for a single ecosystem. This paper summarises the SMB equation, examinesthe uncertainties in deriving input values andreviews other works on the key assumptions.     

Integration of the Pesticide Impact Rating Index with a Geographic Information System for the Assessment of Pesticide Impact on Water Quality

The pesticide impact rating index (PIRI) has been integrated with a Geographic Information System (GIS) to enable regional assessment of pesticide impact on groundwater and surface water resources. The GIS version of PIRI (PIRI-GIS) was used to assess the impact of pre-planting atrazine use in the pine plantations on the Gnangara Mound, Western Australia. The impact on groundwater was found to be spatially variable, mainly dependent on soil type and depth to groundwater, because land use variables were spatially constant. Areas with the greatest impact on groundwater were those where the soil had a low sorption capacity for atrazine. Knowledge of the spatial distribution of the sorption coefficient based on organic carbon (K _oc) for atrazine was found to significantly improve the results from PIRI-GIS. Average values for K _oc (i.e. based on overseas data) were too low for most of the local soil types, resulting in a general overestimation of pesticide impact on groundwater resources, but an underestimation of impact in areas that should be of greatest concern (i.e. where the soil has a low sorption capacity for atrazine).     

Uncertainties in Large Scale Assessments of Critical Load Exceedances

In the 1999 Gothenburg protocol to the UN/ECE LRTAP Convention andin the negotiations for an EU acidification strategy the area withexceedances of critical loads has been the preferred measure forenvironmental impacts. The aim of this study has been to assessthe influence of the uncertainty and spatial variation of both thecritical loads and deposition values on the calculated area withexceedances of critical loads. This has been done on a nationalscale for Denmark and on the European scale based on the dataincluded in the RAINS model. It is demonstrated that includinguncertainty and spatial variation in exceedance calculations, ingeneral gives larger exceeded area for the critical load ofacidity, CL(A). The picture for the critical load of nutrientnitrogen, CL_nut(N), is more mixed because of the higherproportion of exceeded areas. A further point of interest is thepossibility of validating relationships between critical loadexceedances and observable damage based on large scale monitoringand model data. It is demonstrated that it will probably not bepossible to use exceedance calculations on European scale as basisfor validation exercises, linking exceedances to observable damage.     

A Novel Environmental Quality Criterion for Acidification in Swedish Lakes – An Application of Studies on the Relationship Between Biota and Water Chemistry

The recovery from acidification has led to the demand for more precise criteria for classification of acidification. The Swedish Environmental Protection Agency has revised Sweden’s Ecological Quality Criteria for acidification to improve the correlation between the chemical acidification criteria and biological effects. This paper summarises the most relevant findings from several of the studies commissioned for this revision. The studies included data on water chemistry in 74 reference lakes in southern Sweden with data on fish in 61 of the lakes, as well as data on littoral fauna in 48 lakes. We found that the acidity variable most strongly correlated to the biota was the median pH from the current year. Our results probably do not reflect the mechanisms behind the negative effects of acidity on the biota, but are fully relevant for evaluation of monitoring data. The biogeochemical models used for predicting acidification reference conditions generate a pre-industrial buffering capacity. In order to get an ecologically more relevant criteria for acidification based on pH, we transferred the estimated change in buffering capacity into a corresponding change in pH. A change of 0.4 units was defined as the threshold for acidification. With this criterion a considerably lower number of Swedish lakes were classified as acidified when compared with the present Ecological Quality Criteria.     

Non-reactive solute diffusion in unconfined and confined specimens of a compacted soil

The effect of specimen confinement on the determination of the effective diffusion coefficients, D*, for chloride, a non-reactive (non-adsorbing) solute, diffusing in a compacted soil was evaluated. The diffusion tests were performed by placing an acetic acid/sodium acetate buffer solution containing ZnCl2 (pH approximately 4.8) in a reservoir in contact with unconfined and confined specimens of a compacted sand-clay mixture for test durations of 7 or 14 d. The concentrations of chloride in the reservoir were measured as a function of time during the test, as well as a function of depth within the specimen at the end of the test. The resulting concentration distributions were analyzed using two models to Fick's second law for non-reactive solute diffusion in porous media, viz., (1) an analytical model assuming the porosity distribution could be represented by a single, weighted mean porosity and (2) a commercially available model, POLLUTE, that directly accounted for the measured porosity distribution. The D* for unconfined specimens based on the analytical model tended to be overestimated by a factor ranging from 1.13 to 1.59 relative to the D* using POLLUTE, whereas the D* values based on both methods for confined specimens typically were more consistent. In addition, the D* for unconfined specimens was greater than the D* for confined specimens when soil concentrations were used for the analysis, presumably due to the higher porosity for the unconfined specimens relative to the confined specimens. Analyses based on reservoir concentrations were inconsistent and contradictory in some cases, suggesting that the D* values based on soil concentrations were more reliable.     

WFGD添加剂研究进展与应用探讨

从增效机理和应用两方面总结了国内外WFGD添加剂的研究成果,为实际应用中添加剂的选择提供了借鉴,指出WFGD添加剂的研究发展方向是复合添加剂以及发展化工产业副产品或废料用作添加剂的技术。     

阻尼降噪材料的研究进展

阻尼降噪材料作为一类功能环保材料，因其优越的减振、抗冲击、隔噪声性能而获得广泛应用，介绍了阻尼降噪材料的作用机理，综述了聚合物基阻尼降噪材料、金属类阻尼降噪材料、阻尼降噪复合材料及其他阻尼降噪材料的研充进展，分析了阻尼降噪材料住未来的发展趋势。     

火电厂脱硫设施迎检工作分析及建议

为了管理和运行好脱硫设施，并顺利通过国家有关检查、验收，同时反映电力企业的困难和问题，漳泽电力河津发电分公司在2010年上半年接受数十次检查的基础上，针对最严的一次检查，结合理论分析，提出了脱硫设施迎检工作的前期资料准备，阐述了机组启、停及运行期间各种数据间的关联性，并从7个方面重点分析了现场工作的主要环节；同时，提出了确定合理脱硫电价、启动煤电联动等建议。     

欧盟含氟温室气体管控政策及对我国相关进出口管理的启示

《关于消耗臭氧层物质的蒙特利尔议定书》(简称《议定书》)的《基加利修正案》(简称《修正案》)是继气候变化《巴黎协定》后又一里程碑式的重要文件。本文总结了《修正案》的核心要素,介绍了欧盟利用新修订的《含氟温室气体法规》对氢氟碳化物(HFCs)类物质开展管理的主要措施和制度,分析了该法规执行以来的效果和过程中存在的问题,提出了欧盟HFCs管控政策对我国进出口管理的政策法规、进出口禁令和配额管理等的管控启示。     

Research on the recycling industry development model for typical exterior plastic components of end-of-life passenger vehicle based on the SWOT method

In-depth studies on the recycling of typical automotive exterior plastic parts are significant and beneficial for environmental protection, energy conservation, and sustainable development of China. In the current study, several methods were used to analyze the recycling industry model for typical exterior parts of passenger vehicles in China. The strengths, weaknesses, opportunities, and challenges of the current recycling industry for typical exterior parts of passenger vehicles were analyzed comprehensively based on the SWOT method. The internal factor evaluation matrix and external factor evaluation matrix were used to evaluate the internal and external factors of the recycling industry. The recycling industry was found to respond well to all the factors and it was found to face good developing opportunities. Then, the cross-link strategies analysis for the typical exterior parts of the passenger car industry of China was conducted based on the SWOT analysis strategies and established SWOT matrix. Finally, based on the aforementioned research, the recycling industry model led by automobile manufacturers was promoted.     

Time-series analysis of excess mercury in China

In October 2013, China signed the Minamata Convention on Mercury as the 30th signatory state, and its implementation will have a significant impact on the development, use, and management of mercury. Therefore, estimating excess mercury has become extremely important for providing fundamental information for strategic mercury management, such as planning the necessary storage capacity and the timeline for taking appropriate actions. In this study, quantitative information on past and current domestic supply and demand and on excess mercury over a 55-year period (1996–2050) in China was assessed through maximum and minimum scenario analyses. The total mercury supply increased markedly between 1996 and 2016, particularly during the 3 most recent years. The total demand for mercury during the same period increased gradually compared to the total supply. The amount of annual excess mercury has grown rapidly since 2014, from 636?–756 tons in 2013 to 2725–2845 tons in 2016. The minimum excess mercury scenario shows that cumulative excess mercury will continue to decline from 2017 on, and will reach one-third of 2016 levels in 2050. The cumulative amount in 2050 in the maximum scenario will be 3.5 times higher than that in the minimum scenario. The method applied would be useful for policymakers in other countries that are facing similar problems.     

The use of LCA in selecting the best MSW management system

This paper focuses on the study of eleven environmental impact categories produced by several municipal solid waste management systems (scenarios) operating on a provincial scale in Southern Italy. In particular, the analysis takes into account 12 management scenarios with 16 management phases for each one. The only difference among ten of the scenarios (separated kerbside collection of all recyclables, glass excepted, composting of putrescibles, RDF pressed bales production and incineration, final landfilling) is the percentage of separated collection varying in the range of 35–80%, while the other two scenarios, for 80% of separate collection, consider different alternatives in the disposal of treatment residues (dry residue sorting and final landfilling or direct disposal in landfill). The potential impacts induced on the environmental components were analysed using the life cycle assessment (LCA) procedure called “WISARD” (Waste Integrated System Assessment for Recovery and Disposal). Paper recycling was the phase with the greatest influence on avoided impacts, while the collection logistics of dry residue was the phase with the greatest influence on produced impacts. For six impact categories (renewable and total energy use, water, suspended solids and oxydable matters index, eutrophication and hazardous waste production), for high percentages of separate collection a management system based on recovery and recycling but without incineration would be preferable.     

脱硫石膏综合利用的现状与展望

介绍了国内外脱硫石膏在农业、水泥行业、建材行业和其他方面的综合利用情况,以及脱硫石膏分解技术的研究现状,探讨了分解温度、反应气氛和催化成分等因素对脱硫石膏分解效果的影响,展望了脱硫石膏的应用前景。指出:寻找脱硫石膏综合利用的新途径、找出适合脱硫石膏还原分解的气氛及其分解规律、探索有利于脱硫石膏还原分解的条件,是我国脱硫石膏实现循环利用的必经之路。     

Caesium sorption by hydrated cement as a function of degradation state: experiments and modelling

To provide reliable K(d) data for Cs required for the performance assessment of cement-based radioactive waste repositories, two complementary approaches were followed. First, Cs sorption was determined on a range of hydrated cement paste (HCP) and mortar samples of CEM I and CEM V for different degradation states and solution compositions, as well as on some single mineral phases. Second, a surface complexation-diffuse layer model previously developed by Pointeau et al. [Pointeau, I., Marmier, N., Fromage, F., Fedoroff, M., Giffaut, E., 2001. Cs and Pb uptake by CSH phases of hydrated cement. Material Research Society Symposium Proceedings, 663, 105-113] for Cs sorption on synthetic CSH phases was simplified to facilitate its application to whole HCP and mortars or concrete, following re-assessment of the model parameters. All measurements were compared with model predictions. The sorption data obtained on the different solid phases as a function of conditions corroborate that CSH minerals are the main sorbing phase for Cs in HCP. The data also clearly show the important influence of pH and the dissolved concentration of Na, K and Ca on K(d). It is further suggested that a decrease of pH is concomitant with a decrease of the Ca/Si ratio and a corresponding increase in surface sites with high affinity for Cs and, thus, K(d). Elevated concentrations of cations able to compete with Cs for these sites lead to a decrease of K(d), on the other hand. The simplified model was applied to the sorption measurements performed within this study as well as to a variety of literature data, mainly K(d) values for a variety of fresh HCP and mortar or concrete samples based on different samples of Ordinary Portland Cement as well as blended cements. The results show that the model can be applied reasonably well to a very large variety of conditions in terms of solid and solution compositions that cover a range of K(d) values from 10(-4) to ca. 3.2m(3)/kg. The large scatter typically observed for Cs sorption, especially on fresh HCP samples prepared from different formulations, can be explained quantitatively by the variable concentrations of Na and K in the respective solutions, which compete with Cs for fixation sites. On the other hand, the comparatively uniform conditions in degraded HCP typically render the prediction of K(d) values less uncertain than in case of fresh HCP.     

Comparative environmental assessment of natural and recycled aggregate concrete

Constant and rapid increase in construction and demolition (C&D) waste generation and consumption of natural aggregate for concrete production became one of the biggest environmental problems in the construction industry. Recycling of C&D waste represents one way to convert a waste product into a resource but the environment benefits through energy consumption, emissions and fallouts reductions are not certain. The main purpose of this study is to determine the potentials of recycled aggregate concrete (concrete made with recycled concrete aggregate) for structural applications and to compare the environmental impact of the production of two types of ready-mixed concrete: natural aggregate concrete (NAC) made entirely with river aggregate and recycled aggregate concrete (RAC) made with natural fine and recycled coarse aggregate. Based on the analysis of up-to-date experimental evidence, including own tests results, it is concluded that utilization of RAC for low-to-middle strength structural concrete and non-aggressive exposure conditions is technically feasible. The Life Cycle Assessment (LCA) is performed for raw material extraction and material production part of the concrete life cycle including transport. Assessment is based on local LCI data and on typical conditions in Serbia. Results of this specific case study show that impacts of aggregate and cement production phases are slightly larger for RAC than for NAC but the total environmental impacts depend on the natural and recycled aggregates transport distances and on transport types. Limit natural aggregate transport distances above which the environmental impacts of RAC can be equal or even lower than the impacts of NAC are calculated for the specific case study.     

Evaluation of leaching and extraction procedures for soil and waste

Laboratory leaching tests may be used for source term determination as a basis for risk assessment for soil-groundwater pathways on contaminated sites. In order to evaluate different leaching procedures, batch extraction tests and percolation tests were performed using three reference materials produced from contaminated soil, demolition waste and municipal solid waste incinerator bottom ash. Emphasis was placed on the investigation of the leachability of the heavy metals copper and chromium, polycyclic aromatic hydrocarbons (PAHs) and the anions chloride and sulfate. Significant discrepancies between column experiments and batch/extraction tests were found for the release of PAHs and to a lesser extent for the heavy metals Cu and Cr. Additionally interlaboratory comparisons were conducted based on different leaching tests with the reference materials and evaluated using the criteria of comparability and reproducibility. The best reproducibility was achieved for all investigated substances in column tests. The reproducibility of batch tests was acceptable except for PAHs. The results from the experimental work will help establish standardized and feasible laboratory procedures as fundamental for substance specific risk assessment of contaminated sites.     

Scaling and Mapping Regional Calculations of Soil Chemical Weathering Rates in Sweden

Weathering rates of base cations are crucial in critical load calculations and assessments of sustainable forestry. The weathering rate on a single site with detailed geological data can be modelled using the PROFILE model. For environmental assessments on a regional scale, the weathering rates for sites are scaled into regional maps. The step from sites to regional level requires focus on the spatial variation of weathering rates. In this paper, a method is presented by which weathering rates are calculated for 25589 Swedish sites with total elemental analysis for the soil. Based on a part of the results, a methodology for creating area covering maps by geostatistical analysis and kriging is described. A normative reconstruction model was used to transform total elemental analysis to mineralogy. Information from the Swedish Forest Inventory database and other databases were used to derive texture and other important information for the sites, e.g. climate, deposition and vegetation data. The calculated weathering rates show a regional pattern that indicates possibilities for interpolation of data in large parts of Sweden. Geostatistical analysis of an area in southern Sweden shows different properties for different base cations. Kriging was performed for potassium to demonstrate the method. It was concluded that different base cations and different regions have to be analysed separately, in order to optimise the kriging method.     

Use of recycled plastics in wood plastic composites – A review

The use of recycled and waste thermoplastics has been recently considered for producing wood plastic composites (WPCs). They have great potential for WPCs manufacturing according to results of some limited researches. This paper presents a detailed review about some essential properties of waste and recycled plastics, important for WPCs production, and of research published on the effect of recycled plastics on the physical and mechanical properties of WPCs.