含氟改性聚丙烯酰胺絮凝剂的合成及其絮凝性能

以全氟辛基乙基丙烯酸十二氟庚酯(PFMA)为疏水单体,与丙烯酰胺(AM)、二烯丙基二甲基氯化铵(DMDAAC)通过自由基胶束共聚法制得含氟改性聚丙烯酰胺(FPAD)絮凝剂。最佳聚合反应工艺条件:PFMA质量分数为0.3%,引发剂质量分数为0.3%,DMDAAC质量分数为15%,共聚反应温度为50℃。用FPAD处理初始透光率为20%、初始COD为282mg/L的废水,当FPAD加入量为15mg/L、絮凝体系pH为6时,废水透光率最高,可达98.7%;pH为6～9时,废水透光率和COD去除率均较高。     

有机硅改性破乳-絮凝剂在含油污水处理中的应用

采用破乳-絮凝法结合有机硅表面活性剂处理塔里木油田含油污水,以水样的油含量、Zeta电位、显微照片、界面张力为考察参数,得到一种新型水处理剂NP-22。NP-22为有机硅改性破乳-絮凝剂,其配方为破乳-絮凝剂YL-7和有机硅表面活性剂321的质量比95∶15。在NP-22加入量90 mg/L、反应温度45℃、沉降时间90min的优化条件下处理含油污水,水样的油含量由728.8 mg/L降至34.3 mg/L,除油率达95.3%。有机硅表面活性剂321可有效降低油水界面张力,与YL-7复合使用,可取得更好的除油效果。     

生物絮凝法与化学絮凝法处理洗毛废水的比较

分别采用生物絮凝法和化学絮凝法处理300 mL COD为20 000 mg/L、SS为4 000 mg/L的洗毛废水,最佳生物絮凝条件:生物絮凝剂加入量为5 mL,反应温度为30℃,先以120 r/min搅拌5 min、再以60 r/min搅拌35 min,洗毛废水pH为9.0.COD去除率达92%.最佳化学絮凝条件:化学絮凝剂加入量为30 mL,反应温度为40℃,先以120 r/min搅拌5 min、再以60 r/min搅拌25 min,洗毛废水pH为5.0.COD去除率达93%.生物絮凝剂和化学絮凝剂对洗毛废水的絮凝效果接近,但生物絮凝剂的加入量比化学絮凝剂少很多.     

改性高分子絮凝剂去除水中悬浮物和Hg~(2+)

采用自制改性高分子絮凝剂巯基乙酰聚乙烯亚胺处理含Hg2+废水。实验结果表明:当Hg2+的质量浓度100 mg/L、絮凝剂的加入量3.7 mg/L、废水pH=5.0、浊度为0时,Hg2+的去除率达到88%;Hg2+和悬浮物在废水中共存时,当Hg2+的质量浓度100 mg/L、浊度127 NTU时,Hg2+和悬浮物可相互促进彼此的去除,浊度的去除率由40%左右增至95%以上;用该絮凝剂处理实际废水(Hg2+的质量浓度20~25 mg/L、浊度126 NTU、pH=3.5),当絮凝剂加入量为4.2 mg/L时,Hg2+的去除率为84%,浊度的去除率为97%,且处理效果明显优于相同条件下的传统絮凝剂。     

电絮凝技术处理煤气化灰水

采用电絮凝技术处理粉煤加压气化航天炉装置产生的灰水。中试结果显示：灰水经电絮凝一体化装置处理后,出水中总钙和总镁的平均值分别降至180 mg/L和11.1 mg/L,有效抑制了结垢的发生;相对于单一氢氧化钠,碳酸钠和氢氧化钠共同作用的处理效果更好。工业化应用结果表明,电絮凝一体化装置对灰水的总硬度、浊度和悬浮物均有较好的去除效果,其平均去除率分别为32.5%、66.7%和73.0%。采用该技术处理煤气化灰水具有较强的经济性。     

絮凝-微滤组合工艺处理炼油厂“三泥”水相的研究

采用絮凝剂絮凝和陶瓷膜微滤的组合工艺处理炼油厂“三泥”水相。研究结果表明：絮凝处理可明显降低水相的石油类浓度和COD,将絮凝处理与0．2μm氧化锆膜过滤处理相结合,渗透液的石油类浓度和COD可达到国家排放标准。以絮凝处理后出水的石油类浓度为基准,确定了合适的絮凝剂为3530S,并通过正交试验确定了合适的絮凝处理工艺条件：絮凝剂加入量为70mg／L,絮凝温度为40℃,搅拌时间为90min,静置时间为1．5h。同时,絮凝处理能减轻膜污染,增大膜的渗透通量。考察了操作压力和错流速率对渗透液质量和膜渗透通量的影响,确定了合适的操作条件：操作压力为0．11MPa,错流速率应保证在完全湍流区。     

负压蒸发技术处理废弃钻井液

采用负压蒸发技术处理3种不同组分的废弃钻井液。实验结果表明:最佳蒸发温度为79℃;当蒸发温度低于95℃时,相15~#原液的出水氨氮质量浓度、悬浮物质量浓度、色度分别低于3.40 mg/L、0.093 mg/L、11倍,达到GB 8978—1996《污水综合排放标准》中的一级排放标准;当蒸发温度低于79℃时,钻井液1和钻井液2的出水氨氮质量浓度均低于37.00 mg/L,悬浮物质量浓度均低于0.080 mg/L,色度低于13倍,COD低于114.0 mg/L,达到GB 8978—1996《污水综合排放标准》中的二级排放标准。通过后续过滤除油工艺可降低钻井液中的石油类质量浓度,使最终出水达标排放。     

改性高分子絮凝剂去除水中悬浮物和Hg2+

采用自制改性高分子絮凝剂巯基乙酰聚乙烯亚胺处理含Hg²⁺废水。实验结果表明：当Hg²⁺的质量浓度100 mg/L、絮凝剂的加入量3.7 mg/L、废水pH=5.0、浊度为0时，Hg²⁺的去除率达到88%；Hg²⁺和悬浮物在废水中共存时，当Hg²⁺的质量浓度100 mg/L、浊度127 NTU时，Hg²⁺和悬浮物可相互促进彼此的去除，浊度的去除率由40%左右增至95%以上；用该絮凝剂处理实际废水（Hg²⁺的质量浓度 20~25 mg/L、浊度126 NTU、pH=3.5），当絮凝剂加入量为4.2 mg/L时，Hg²⁺的去除率为84%，浊度的去除率为97%，且处理效果明显优于相同条件下的传统絮凝剂。     

阳离子淀粉-丙烯酰胺接枝共聚物絮凝剂的制备及其絮凝性能

研究了阳离子淀粉与丙烯酰胺接枝共聚反应制备阳离子型絮凝剂的工艺，并用硅藻土悬浊液及实际水样对产物的絮凝性能进行了考察。其最佳合成条件：阳离子淀粉与丙烯酰胺的质量比为1：4，引发剂加入量为丙烯酰胺质量的0．1％，反应温度50℃，反应时间3h。絮凝效果实验中，接枝共聚物絮凝剂的最佳加入量为4mg／L。与阳离子淀粉和阳离子聚丙烯酰胺絮凝剂相比，接枝共聚物絮凝剂对渭河水及造纸网下白水的絮凝效果更好。     

催化臭氧氧化—好氧生化—膜分离组合工艺处理砷化镓生产废水的工程应用

为了解决砷化镓生产废水含有磷酸盐、氟化物、砷化物以及难沉降亚微米级悬浮物的处理难点,首先采用催化臭氧氧化—好氧生化深度预处理废水,再采用RO膜分离工艺进行处理。结果表明：催化臭氧氧化法使废水中亚微米级悬浮物脱稳,有利于悬浮物的混凝沉降,并优化了膜分离阶段的分离环境,可延长膜使用寿命,降低运行成本;经过膜分离后,出水砷质量浓度为0.01 mg/L,氟质量浓度为1.0 mg/L,COD、TP、TN和ρ（NH₃-N）为10,0.01,0.50,0.50 mg/L,均达到《地表水环境质量标准》（GB3838—2002）Ⅲ类水质标准。     

阳离子聚丙烯酰胺复配钠基膨润土处理模拟苯酚废水

将阳离子聚丙烯酰胺与钠基膨润土进行复配,制备出复合吸附剂,并将其用于模拟苯酚废水的处理。采用XRD和FTIR技术对复配前后的钠基膨润土进行了表征。表征结果显示:阳离子聚丙烯酰胺附着在钠基膨润土的表面,对钠基膨润土的表面具有改性作用,使其由亲水性变为疏水性。实验结果表明:在阳离子聚丙烯酰胺与钠基膨润土的复配比例为200 mg/g、反应时间为40 min、复合吸附剂投加量为6 g/L、废水p H为11的最佳条件下,于25℃处理苯酚质量浓度为50 mg/L的模拟苯酚废水,苯酚去除率达89.5%。     

The use of alum, ferric chloride and ferrous sulphate as coagulants in removing suspended solids, colour and COD from semi-aerobic landfill leachate at controlled pH.

Suspended solids, colour and chemical oxygen demand (COD) are among the main pollutants in landfill leachate. Application of physical or biological processes alone is normally not sufficient to remove these constituents, especially for leachate with a lower biochemical oxygen demand (BOD)/ COD ratio. The main objective of this research was to investigate the efficiency of coagulation and flocculation processes for removing suspended solids, colour and COD from leachate produced in a semi-aerobic landfill in Penang, Malaysia. A 12-month characterization study of the leachate indicated that it had a mean annual BOD/COD ratio of 0.15 and was partially stabilized, with little further biological degradation likely to occur. Particle size analysis of the raw leachate indicated that its 50th percentile (d50) was 11.68 microm. Three types of coagulants were examined in bench scale jar test studies: aluminium sulphate (alum), ferric chloride (FeCl3) and ferrous sulphate (FeSO4). The effects of agitation speed, settling time, pH, coagulant dosages and temperature were examined. At 300 rpm of rapid mixing, 50 rpm of slow mixing, and 60 min settling time, higher removals of suspended solids (over 95%), colour (90%) and COD (43%) were achieved at pH 4 and 12. FeCl3 was found to be superior to other coagulants tested. At pH 4 and 12, fair removal of suspended solids was observed at a reasonably low coagulant dose, i.e., 600 mg L(-1); hHowever, about 2500 mg L(-1) of coagulant was required to achieve good removals at pH 6. Better removals were achieved at higher temperature. The d50 of sludge after coagulation at pH 4 with a 2500 mg L(-1) FeCl3 dose was 60.16 microm, which indicated that the particles had been removed effectively from the leachate. The results indicate that coagulation and flocculation processes can be used effectively in integrated semi-aerobic leachate treatment systems, especially for removing suspended solids, colour and COD.     

不同类型清水剂处理油田含聚污水的效果对比

考察了阳离子型CWC-14、非离子型NQS-01和阴离子型AQS-08 3类清水剂对油田含聚污水的处理效果,对比了它们的作用特点和絮体性能。实验结果表明:在清水剂加入量350 mg/L、处理温度65℃、搅拌转速300 r/min、搅拌时间5 min的条件下,CWC-14、NQS-01和AQS-08对含聚污水的除油率分别为98.8%、98.0%和99.4%;NQS-01受处理温度、搅拌条件影响较大;CWC-14受污水中聚合物质量浓度影响最大。清水剂的絮体特点与其作用机理有关,CWC-14的絮凝速率最快,起效时间最短,絮体呈黏性大块状;NQS-01的絮凝速率最慢,起效时间最长,絮体呈浮油状;AQS-08的絮凝速率和起效时间适中,絮体呈松散状、流动性好。对比结果表明,非阳离子型清水剂可有效避免油田含聚污水处理过程中的黏性油泥问题。     

微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水

采用微电解—Fenton氧化—絮凝组合工艺处理油田压裂废水,优化了工艺条件。实验结果表明：最佳工艺条件为初始废水pH 3.0、铁屑加入量1.5 g/L（铁屑与活性炭的质量比1∶1）、微电解时间80 min、Fenton氧化时间120 min、H₂O₂加入量940 mg/L,阳离子聚丙烯酰胺加入量120 mg/L;在最佳工艺条件下处理废水后,COD由3 116.0 mg/L降至681.3 mg/L,总COD去除率达78.1%,3个工段的COD去除率依次为33.1%,37.9%,7.1%,出水水质满足现场回注标准（SY/T 5329—2012《碎屑岩油藏注水水质推荐指标及分析方法》）;该组合工艺对废水的处理效果远优于单独微电解、Fenton氧化或絮凝工艺,且方法简单易行、药剂利用率高。     

水性油墨废水絮凝污泥制备吸附剂及阳离子染料的吸附

以水性油墨废水絮凝污泥为原料、采用一步炭化活化法制备了吸附剂,并将其用于阳离子蓝X-GRRL溶液(300 mg/L)的吸附处理。考察了吸附剂投加量、吸附时间、吸附温度和吸附pH对吸附效果的影响,并对吸附动力学进行了探讨。结果表明:所制得吸附剂的总孔体积为0.5 cm~3/g,平均孔径为7.12 nm;在吸附剂投加量0.6g/L、吸附时间420 min、吸附温度25℃、吸附pH 5.4的条件下,吸附量高达486.21 mg/g,脱色率达97.24%;该吸附剂对于阳离子蓝X-GRRL的吸附过程可用准二级动力学模型和颗粒内扩散效应模型很好地描述。     

Treatment of Stormwater using Fibre Filter Media

In this study, a high-rate fibre filter was used as a pre-treatment to stormwater in conjunction with in-line flocculation. The effect of operating the fibre filter with different packing densities (105, 115 and 125 kg/m³) and filtration velocities (20, 40, 60 m/h) with and without in-line flocculation was investigated. In-line flocculation was provided using 5, 10 and 15 mg/L of ferric chloride (FeCl₃·6H₂O). The filter performance was studied in terms of pressure drop (ΔP), solids removal efficiency, heavy metals (total) removal efficiency and total organic carbon (TOC) removal efficiency. It is found that the use of in-line flocculation at a dose of 15 mg/L improved the performance of fibre filter as measured by turbidity removal (95%), total suspended solids reduction (98%), colour removal efficiency (99%), TOC removal (reduced by 30–40 %) and total coliform removal (93%). The modified fouling index reduced from 750–950 to 12 s/L² proving that fibre filter can be an excellent pre-treatment to membrane filtration that may be consider as post-treatment. The removal efficiency of heavy metal was variable as their concentration in raw water was small. Even though the concentration of some of these metals such as iron, aluminium, copper and zinc were reduced, others like nickel, chromium and cadmium showed lower removal rates.     

用新型絮凝剂处理制浆漂白废水

采用一种新型的有机无机复合型高分子絮凝剂(F-1)处理制浆漂白废水，进行了絮凝条件的优选试验和对比试验，结果表明：F-1絮凝剂的絮凝沉降效果与絮凝剂的用量、废水的pH有很大的关系。当废水的pH为6．0、絮凝剂用量为100mg／L时，漂白废水的色度、SS和COD的去除率分别为98．2％、93．6％和78．6％。而且，其絮凝性能明显优于阳离子聚丙烯酰胺(PAMC)、聚合氯化铝(PAC)以及聚合硫酸铁(PFS)等絮凝剂。