Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash

Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.     

Experimental and Modeling Studies for the Removal of Crystal Violet Dye from Aqueous Solutions using Eco-friendly <Emphasis Type="Italic">Gracilaria corticata</Emphasis> Seaweed Activated Carbon/Zn/Alginate Polymeric Composite Beads

This research article describes, an eco-friendly activated carbon prepared from the Gracilaria corticata seaweeds which was employed for the preparation of biodegradable polymeric beads for the efficient removal of crystal violet dye in an aqueous solution. The presence of chemical functional groups in the adsorbent material was detected using FTIR spectroscopy. The morphology and physical phases of the adsorbent materials were analyzed using SEM and XRD studies respectively. Batch mode dye adsorption behavior of the activated carbon/Zn/alginate polymeric beads was investigated as a function of dosage, solution pH, contact time, initial dye concentration and temperature. Maximum dye removal was observed at a pH of 5.0, 1 g of adsorbent dosage with 60 mg/L dye concentration, 50 min of contact time and at 30 °C. The equilibrium modeling studies were analyzed with Freundlich and Langmuir adsorption isotherms and the adsorption dynamics was predicted with Lagergren’s pseudo-first order, pseudo-second order equations and intra particle diffusion models. The process of dye removal followed a pseudo second-order kinetics rather than pseudo first order. The thermodynamic parameters like standard Gibbs free energy change (ΔG°), enthalpy change (ΔH°) and entropy change (ΔS°) were determined and the results imply that the adsorption process was spontaneous, endothermic and increases the randomness between the adsorbent and adsorbate. The results from the experimental and correlation data reveal that the Gracilaria corticata activated carbon/Zn/alginate polymeric beads have proved to be an excellent adsorbent material for the removal of CV dye.     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.     

Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Adsorptive Removal of Diuron Herbicide on Carbon Nanotubes Synthesized from Plastic Waste

In this study, carbon nanotubes (CNTs) were synthesized from waste polyethylene bottles and their use as an adsorbent for the removal of diuron herbicide from aqueous solution was evaluated. Batch adsorption was performed by varying adsorbent dosage, initial concentration, contact time, and temperature. Kinetic models applied to experimental data indicated that the pseudo-second-order model had the best fit. The equilibrium data were analyzed using different isotherm models. The adsorption capacity of CNTs for diuron removal, determined using the Hill isotherm, was approximately 40.37 mg/g at 303 K. From thermodynamic studies, the values of ΔH° (kJ/mol) and ΔS° [kJ/(mol K)] were calculated as ?17.307 and ?0.0528, respectively, which suggested that the adsorption process was exothermic. The negative values of ΔG° at three different temperatures indicated that adsorption of diuron on CNTs was favorable.     

Assessment of Potential Capability of Water Bamboo Leaves on the Adsorption Removal Efficiency of Cationic Dye from Aqueous Solutions

Removal of toxic pollutants from water and wastewater is becoming an important process with the increase of industrial activities. The present study focused on assessing the suitability and efficiency of water bamboo leaves (WBL) for the removal of cationic dye from aqueous solutions. The effect of different variables in the batch method including solution pH (2–12), initial dye concentration (50–250 mg L^?1), adsorbent dose (0.05–0.30 g), contact time (5–180 min) and temperature (283–333 K) on the dye removal was investigated. The adsorption kinetics was discussed in view of four kinetics models. The results showed that the pseudo-second-order kinetics model described dye adsorption on WBL very well. The experimental equilibrium data were also tested by four isotherm models. It was found that adsorption of dye on WBL fitted well with the Langmuir isotherm model, implying the binding energy on the whole surface of the adsorbent was uniform and the dye molecules onto the surface of the adsorbent were monolayer coverage. Calculation of various thermodynamic parameters of the adsorption process indicated feasibility and exothermic nature of dye adsorption.     

Removal of fluoride from water using aluminum-modified activated carbon prepared from khat (Catha edulis) stems

This study investigated the fluoride removal efficiency and adsorption of a low-cost adsorbent prepared using aluminum-modified activated carbon from khat (Catha edulis) in a batch-mode reactor. The operating factors, including pH, adsorbent dose, and fluoride initial concentration, were optimized using the Box Behnken design of response surface methodology. The correlation coefficient (R²) for the removal of fluoride was found to be 0.93, showing the validity of the developed quadratic model. The results showed that, under optimized conditions of an adsorbent dose of 2.47 g/L, an initial fluoride concentration of 2.1 mg/L, an initial pH 6.08, and 60 min, 90% fluoride reduction was achieved. Meanwhile, the adsorption isotherm and kinetics followed the Langmuir adsorption model and the Pseudo second model, respectively, with a monolayer adsorption capacity of 0.3065 mg/g. On the other hand, Fourier transform infrared spectroscopy and scanning electron microscopy analyses revealed the formation of major peaks of components such as hydroxyl and carboxylic acids. The same optimum treatment conditions (adsorbent dose of 2.47 g/L, initial pH 6.08, and treatment time of 60 min) managed to remove low initial fluoride concentrations of 3.67 and 4.33 mg/L from real groundwater by 72.84% and 70.37%, respectively. The modified adsorbent prepared in this study successfully treat the low fluoride concentration to a level recommended by WHO for drinking water.     

Adsorptive Separation of Lysozyme from Aqueous Solutions Using Sulphonyl and Carboxyl Functionalized Stearyl Alcohol Grafted Epichlorohydrin

In the present work ability of the two novel adsorbents, sulphonyl and carboxyl functionalized stearyl alcohol-grafted epichlorohydrin, SA-g-E-SO₃H, SA-g-E-COOH; to remove lysozyme (LYZ) from aqueous solution was assessed. The adsorbent characterization was done using FTIR, XRD, SEM and TGA analyses. The adsorption efficiency was influenced by solution pH and the optimum operating pH was found to be 4.0 for SA-g-E-SO₃H and 5.0 for SA-g-E-COOH and their adsorption efficiency was evaluated using the various isotherm and kinetics models. The Sips isotherm model and pseudo-second-order kinetic model were found to be the best for describing the equilibrium and kinetic behaviors of the adsorption process. Batch adsorption/desorption studies in acidic medium, for over six cycles showed excellent regeneration capability of the adsorbents and could lead to the development of viable and promising technology for the adsorptive recovery of LYZ from aqueous solutions. The efficiency of the adsorbents for the LYZ adsorption was verified using egg white. The result obtained from this study revealed that adsorption ability of 25 mg of SA-g-E-COOH is 98.4 % which is more than that of SA-g-E-SO₃H (96.2 %). The efficiency of SA-g-E-SO₃H to remove LYZ from aqueous solution was found to be higher compared to SA-g-E-COOH.     

粉煤灰基吸附剂对模拟废水中Cd2+的吸附性能

以粉煤灰为原料、Na2CO3为助熔剂,采用盐熔融—水浴结晶法制备粉煤灰基吸附剂。探讨了吸附剂的最佳制备条件及其对模拟废水中Cd2+的最佳吸附条件、吸附动力学和吸附机理。实验结果表明:制备吸附剂的最佳工艺条件为m(粉煤灰)∶m(Na2CO3)为1∶2,焙烧温度为450℃;采用最佳制备工艺条件下制备的吸附剂(记作2-450℃-FA吸附剂),在初始Cd2+质量浓度为300 mg/L、初始溶液pH为7.7、振荡时间为120 min的条件下,对模拟废水中Cd2+的去除率为98.0%。2-450℃-FA吸附剂对Cd2+的吸附主要受颗粒内扩散控制,吸附过程可用准二级吸附动力学方程很好地描述。Ea为77.22 kJ/mol,吸附过程主要为化学吸附。     

粉煤灰及其制备沸石对高浓度氨氮的去除比较

以粉煤灰为原料,采用改进的水热合成法制备了粉煤灰沸石,并将粉煤灰和粉煤灰沸石用于高浓度氨氮的吸附去除。实验结果表明:在粉煤灰和粉煤灰沸石的投加量分别为0.10 g/m L和0.04 g/m L、反应体系p H为5~7、初始氨氮质量浓度为500 mg/L的条件下,分别吸附660 min和60 min,粉煤灰和粉煤灰沸石对氨氮的去除率分别约为20.1%和50.7%左右,粉煤灰沸石对高浓度氨氮的去除效果明显优于粉煤灰;粉煤灰和粉煤灰沸石对氨氮的吸附动力学行为符合准二级动力学方程;Langmuir和Freundlich等温吸附模型能较好地描述粉煤灰对氨氮的等温吸附过程,而粉煤灰沸石对氨氮的等温吸附过程则更适宜用线性模型和Freundlich模型描述。     

Optimized Removal of Acid Blue 62 from Textile Waste Water by SBA-15/PAMAM Dendrimer Hybrid Using Response Surface Methodology

SBA-15/PAMAM Nano adsorbent was synthesized by the proficiency of SBA-15 as an original compound, 3-chloropropyltrimethoxysilane as a bridge chemical compound and polyamidoamine dendrimer (PAMAM) in the role of a multifunctional amine end group for adsorption of acid blue 62 (AB62) from aqueous media. The synthesized adsorbent was characterized by transmission electron microscope, field emission scanning electron microscope and Fourier-transform infrared spectroscope. A response surface methodology was employed to evaluate the simple and amalgamated factors of the operating variables subtending initial pH (2–12), adsorbent dosage(0.01–0.03 g), contact time (5–120 min), initial dye concentration (40–600 ppm) and temperature (25–45?°C) to optimize the operating statues of the treatment method. These parameters were altered at five levels pursuant to the central composite design to appraise their effects on AB62 removal through analysis of variance. Analysis of variance represented a high coefficient of definition amount (R²?=?0.9999) and acceptable prediction quadratic polynomial model was concluded which ascertain the suitability of the model and a high correlation among the predicted and empirical amounts. Utmost color removal efficiency was auspicated and empirically accredited. The optimum conditions relied on acquired results for AB62 removal were at an initial pH of 2, adsorbent dosage of 0.03 g SBA-15/PAMAM, dye concentration of 40 mg l^?1, time contact of 60 min and temperature of 25?°C.     

改性粉煤灰的制备及其对分散蓝的吸附

以聚二甲基二烯丙基氯化铵(PDMDAAC)为改性剂,制备PDMDAAC改性粉煤灰。采用正交实验考察了制备条件对PDMDAAC在粉煤灰上的负载量的影响。实验结果表明:在反应温度为70℃、反应时间为3 h、PDMDAAC质量浓度为50 g/L、溶液pH为10的最佳条件下,PDMDAAC在粉煤灰上的负载量为0.98 mg/g;在吸附温度为30℃、初始分散蓝质量浓度为50 mg/L、PDMDAAC改性粉煤灰加入量为4 g/L的条件下,PDMDAAC改性粉煤灰对分散蓝的去除率可达98%。PDMDAAC改性粉煤灰对分散蓝的吸附符合Langmuir吸附模型。     

Thorium(IV) Recovery from Water and Sea Water Using Surface Modified Nanocellulose/Nanobentonite Composite: Process Design

Thorium(Th) contamination in the ground water an emerging environmental issue and Th recovery from sea water and nuclear wastewater is of high significance, as it is a major player in the energy sector. For the adsorption and recovery of Th, polymer grafted bio materials are reported as most efficient materials. P(IA/MAA)-g-NC/NB was prepared and all the steps in the synthetic routes were monitored using FTIR, SEM–EDS, and XRD, TG. Efficiency in removal of Th(IV) by P(IA/MAA)-g-NC/NB was tested by batch adsorption technique. The pH dependent Th(IV) adsorption process, was optimized at 4.5 and adsorption equilibrium was achieved within 120 min. Experimental kinetic data correlates well with pseudo-second-order equation, indicates adsorption was chemical process via ion exchange followed by complexation reaction, also could explain the film diffusion process of adsorption. Sips isotherm proved to best fit for the adsorption of Th(IV) onto P(IA/MAA)-g-NC/NB with maximum adsorption capacity of 95.19 mg/g. Thermodynamic studies revealed the endothermic nature, feasibility and spontaneity of the adsorption process. ΔHx and ΔSx were decreased to a small extent from ?5.567 to ?3.439 kJ/mol and increased from 11.18 to 18.39 J/mol, respectively, with increase in surface loading from 50 to 70 mg/g, indicating that the surface of the onto P(IA/MAA)-g-NC/NB is having energetically heterogeneous surface and there may be some lateral interactions between the adsorbed Th(IV) ions Repeated adsorption–desorption study over six cycles, adsorption percentage decreases from 99.0 to 94.6 %, proved the efficiency of P(IA/MAA)-g-NC/NB as an effective adsorbent for the removal and recovery of Th(IV) from aqueous solutions. Complete removal of Th(IV) ions from seawater containing 10 mg/L with a dose of 0.25 g/L P(IA/MAA)-g-NC/NB achieved. Batch adsorption system as double stage reactor designed from the adsorption isotherm data of Th(IV) by constructing operational lines. From these could be concluded that P(IA/MAA)-g-NC/NB is a promising candidate for the effective removal and removal of Th(IV) from industrial effluents phase and sea water. The maximum adsorption capacity Qs for Ceralite IRC-50 calculated which was found to be 179.67 mg/g which are considerably lower than those for P(IA/MAA)-g-NC/NB.     

Agricultural solid waste for the removal of organics: adsorption of phenol from water and wastewater by palm seed coat activated carbon

Adsorption studies for phenol removal from aqueous solution on activated palm seed coat carbon (PSCC) were carried out under varying experimental conditions of contact time, phenol concentration, adsorbent dose and pH. Adsorption equilibrium was reached within 3 h for phenolic concentrations 10-60 mg l(-1). Kinetics of adsorption obeyed a first order rate equation. The percent removal remained constant over the pH range 4-9 for a phenolic concentration of 25 mg (l-1). The equilibrium data could be described well by the Freundlich isotherm equation. The adsorption of phenol on PSCC follows the film diffusion process. A comparative study with a commercial activated carbon showed that PSCC is two times more effective than commercial activated carbon. The studies showed that the palm seed coat carbon can be used as an efficient adsorbent material for the removal of phenolics from water and wastewater.     

Orange peel as an adsorbent in the removal of acid violet 17 (acid dye) from aqueous solutions

The effectiveness of orange peel in adsorbing Acid violet 17 from aqueous solutions has been studied as a function of agitation time, adsorbent dosage, initial dye concentration and pH. The adsorption follows both Langmuir and Freundlich isotherms. The adsorption capacity Q0 was 19.88 mg/g at initial pH 6.3. The equilibrium time was found to be 80 min for 10, 20, 30 and 40 mg/L, dye concentration respectively. A maximum removal of 87% was obtained at pH 2.0 for an adsorbent dose of 600 mg/50 ml of 10 mg/L dye concentration. Adsorption increases with increase in pH. Maximum desorption of 60% was achieved in water medium at pH 10.0.     

Facile Preparation of Chitosan Films for High Performance Removal of Reactive Blue 19 Dye from Aqueous Solution

This study aimed at finding effective strategies for high-performance removal of reactive blue 19 (RB19) dye from aqueous solution. Chitosan (CS) films had been prepared by using solvent casting with mild drying for this purpose. The CS films were characterized by X-ray diffraction, field-emission scanning electron microscopy, and Fourier transform infrared (FTIR) spectroscopy. The performance of RB19 removal using CS were evaluated by varying contact time, solution pH, initial dye concentration, and adsorbent dosage. Adsorption isotherms, kinetics, and desorption were investigated by batch experiments. Results showed that CS films exhibited the optimal adsorption performance for RB19 removal and high maximum adsorption capacities of RB19, which were 799 and 822.4 mg g^?1 at 20 and 40 °C, respectively. Adsorption kinetic data were well described by the pseudo-second-order kinetic model. FTIR analyses further indicated that interactions between RB19 and the CS film occurred during adsorption. The CS films also exhibited satisfactory desorption of RB19 at about 80 % after 30 min of desorption at pH 11. Our study demonstrated that the CS films can be easily prepared and applied for effective removal of RB19 in treatment of wastewater.     

Use of fly ash for the removal of phenol and its analogues from contaminated water

This work attempts to elucidate the effects of different operational variables affecting the mechanistic function of fly ash for removal of some priority organic pollutants viz. phenol and its analogues. Thermodynamic parameters like free energy change, enthalpy and entropy of the process, as well as the sorption isotherms for phenols on fly ash, were measured and the most suitable isotherm was determined. Results of the study indicate that the extent of solute removal is determined by the initial solute concentration, molecular size and molecular arrangement of the solute. At the fixed set of experimental conditions, a model equation can be developed from which the percent removal corresponding to the load of the particular solute is determined. It is assumed that the mechanism of adsorption is governed by the surface characteristics of fly ash; pH has a vital role in influencing the solute removal as both the ionizing power (acidity, pKa) of the solutes and the zero point charge of fly ash (pH(ZPC)) depend on the solution pH. Isotherm pattern and the free energy change indicate that the process is favorable, as well as spontaneous. The information gathered from the study will serve as a predictive modeling procedure for the analysis and design of the removal of organic pollutants and decontamination of water. The leaching experiment indicates that the retained solutes do not release from fly ash. The retained solutes can be recovered and utilized as industrial raw material.     

复合改性粉煤灰对磷的吸附性能

将粉煤灰（FA）与Na₂CO₃混合焙烧后浸渍负载Fe²⁺,制备了复合改性粉煤灰（CMFA）。通过多种手段对CMFA进行了表征,并将其用于含磷废水的吸附处理。表征结果显示：改性后的粉煤灰表面疏松多孔,比表面积增大了21倍,产生了金属盐类熔出物及羟基氧化铁和羟基官能团。实验结果表明：当初始磷质量浓度为50 mg/L、吸附温度为20 ℃、溶液pH为4.3、CMFA投加量为5 g/L、吸附时间为30 min时,磷去除率可达98.01%,较FA的50.10%大幅提升;20 ℃时,CMFA对磷的饱和吸附量可达22.15 mg/g;用拟二级动力学模型可较准确地描述CMFA对磷的吸附过程,该过程为自发的吸热过程,符合Langmuir等温吸附模型,为以离子交换为主的化学吸附。     

Arsenic removal from aqueous solutions by adsorption on red mud

Use of red mud, which is a waste product from bauxite processing, has been explored as an alternate adsorbent for arsenic in this study. The tests showed that the alkaline aqueous medium (pH 9.5) favored the removal of As(III), whereas the pH range from 1.1 to 3.2 was effective for As(V) removal. The process of arsenic adsorption follows a first-order rate expression and obeys the Langmuir's model. It was found that the adsorption of As(III) was exothermic, whereas As(V) adsorption was endothermic. It would be advantageous to use this residue as an adsorbent replacing polyvalent metal salts.     

Removal of Oil from Water by Calcium Alginate Hydrogel Modified with Maleic Anhydride

Calcium alginate hydrogel was prepared and used as a biosorbent for the removal of oil from aqueous solutions. Calcium alginate hydrogel was further chemically modified by esterification with maleic anhydride. The changes in the physicochemical properties of maleic anhydride modified calcium alginate were investigated via multiple techniques (FTIR, SEM, BET and DSC/TGA). Adsorption batch experiments were carried out to compare the oil adsorption capacities of native and modified calcium alginates. Adsorption experiments were carried out as a function of solution pH, temperature and ionic strength to determine the optimal conditions for the adsorption of oil. Equilibrium and kinetic studies were conducted for the modified alginate. Results revealed that the maleic anhydride modification of calcium alginate improved its adsorption capacity towards oil. Higher adsorption capacities of modified alginate were attained at lower temperatures (20 °C), higher ionic strengths (1.0 M NaCl) and within the pH range of 5–9. The oil adsorption data obtained for modified alginate could be better described by the first order kinetic model (R²?=?0.981) and the BET equilibrium isotherm (R²?=?0.984). The maximum monolayer adsorption capacity predicted by the BET model for the modified calcium alginate was found to be 143.0 mg/g.