Analysis of reduction stage of chemical looping packed bed reactor based on the reaction front distribution

Traditional combustion of syngas derived from biomass has incurred numerous environmental problems, and syngas chemical looping combustion is environmentally friendly for syngas energy conversion. As a key part of chemical looping combustion, reactor configuration is noticeable. The dynamically operated packed bed reactor is an emerging conception applied to chemical looping combustion. Our attention is paid to the conversion of the oxygen carrier in the packed bed as the limited maximum conversion of the oxygen carrier in a packed bed is unclear. In this paper, the reaction front distribution during iron oxide reduced by CO is firstly proposed on the basis of chemical equilibrium and then validated by the effluent gas profile. Based on the reaction front distribution, the detail of the reduction stage in iron-based chemical looping combustion is analyzed to obtain the characteristics of reaction fronts. The reaction rates of reduction from Fe₂O₃ to Fe₃O₄, Fe₃O₄ to Fe_0.947O and Fe_0.947O to Fe are 5.280, 3.329 and 4.379 mol m^?3 s^?1, respectively. And the velocities of reaction front I, II, III are 0.605, 0.326, 0.044 cm min^?1, respectively, which demonstrate the reaction front distribution. The methodology established in this paper can be used to study multiple reaction front system in the packed bed reactor.     

化学循环燃烧载氧体的研究进展

化学循环燃烧是集分离捕集CO2和去除NOx为一体的新型燃烧技术。介绍了化学循环燃烧的发展背景、工艺原理及特点；综述了化学循环燃烧载氧体的选材、载氧体的性能要求，对各系载氧体（如NiO系、Fe2O3系、CuO系、CoO系和Mn2O3系载氧体）的性能进行了对比分析；提出了Fe2O3、Fe2O3／Al2O3（质量分数为60％的Fe2O3＋质量分数为40％的Al2O3）、NiO／NiAl2O3（质量分数为50％的活性NiO＋质量分数为50％的NiAl2O3）是当前的优势载氧体，并对载氧体的发展做了展望。     

Mathematical modeling of MSW combustion and SNCR in a full-scale municipal incinerator and effects of grate speed and oxygen-enriched atmospheres on operating conditions

The rising popularity of incineration of municipal solid waste (MSW) calls for detailed mathematical modeling and accurate prediction of pollutant emissions. In this paper, mathematical modeling methods for both solid and gaseous phases were employed to simulate the operation of a 450 t/d MSW-burning incinerator to obtain detailed information on the flow and combustion characteristics in the furnace and to predict the amount of pollutant emissions. The predicted data were compared to on-site measurements of gas temperature, gas composition and SNCR de-NO_X system. The major operating conditions considered in this paper were grate speed and oxygen concentration. A suitable grate speed ensures complete waste combustion. The predictions are as follows: volatile release increases with increasing grate speed, and the maximal value is within the range of 700–800 kg/m² h; slow grate speeds result in incomplete combustion of fixed carbon; the gas temperature at slow grate speeds is higher due to adequate oxygenation for fixed carbon combustion, and the deviation reaches 200 K; NO_X emission decreases, but CO emission and O₂ concentrations increase, and the deviation is 63%, 34% and 35%, respectively. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressure and temperature. The furnace temperature, NO production and CO emission increase as the oxygen concentration increases, and the deviation of furnace exit temperature, NO and CO concentration is 38.26%, 58.43% and 86.67%, respectively. Finally, oxygen concentration is limited to below 35% to prevent excessive CO and NO_X emission without compromising plant performance. The current work greatly helps to understand the operating characteristics of large-scale MSW-burning plants.     

Oxidation catalyst of iron oxide suppressing dioxin formation in polyethylene combustion

A new iron oxide catalyst, which has a superior oxidation activity in carbon monoxide and polyethylene (PE) combustion, was synthesized by an aqueous solution reaction. Catalytic oxidation of carbon monoxide over six kinds of hematite obtained from the goethite was done using a microcatalytic pulse reactor, and the composition of the hematite with the highest oxidation activity was determined. With the aim of suppressing dioxin formation on combustion, incineration tests of solid wastes in PE refuse bags with and without the goethite were carried out using a commercial semibatch-type incinerator with a combustion chamber of 6.2 m³. The result confirmed that the concentration of dioxins in the flue gas decreased considerably when the refuse was incinerated in PE bags manufactured with goethite. Received: July 24, 2000 / Accepted: October 18, 2000     

Combustion and inorganic bromine emission of waste printed circuit boards in a high temperature furnace

High temperature combustion experiments of waste printed circuit boards (PCBs) were conducted using a lab-scale system featuring a continuously-fed drop tube furnace. Combustion efficiency and the occurrence of inorganic bromine (HBr and Br₂) were systematically studied by monitoring the main combustion products continuously. The influence of furnace temperature (T) was studied from 800 to 1400 °C, the excess air factor (EAF) was varied from 1.2 to 1.9 and the residence time in the high temperature zone (RT_HT) was set at 0.25, 0.5, or 0.75 s.Combustion efficiency depends on temperature, EAF and RT_HT; temperature has the most significant effect. Conversion of organic bromine from flame retardants into HBr and Br₂ depends on temperature and EAF. Temperature has crucial influence over the ratio of HBr to Br₂, whereas oxygen partial pressure plays a minor role. The two forms of inorganic bromine seem substantially to reach thermodynamic equilibrium within 0.25 s. High temperature is required to improve the combustion performance: at 1200 °C or higher, an EAF of 1.3 or more, and a RT_HT exceeding 0.75 s, combustion is quite complete, the CO concentration in flue gas and remained carbon in ash are sufficiently low, and organobrominated compounds are successfully decomposed (more than 99.9%).According to these results, incineration of waste PCBs without preliminary separation and without additives would perform very well under certain conditions; the potential precursors for brominated dioxins formation could be destroyed efficiently. Increasing temperature could decrease the volume percentage ratio of Br₂/HBr in flue gas greatly.     

Dioxin emissions from municipal solid waste incinerators (MSWIs) in France

The objective of this study was to determine whether the fear of dioxin/furan emissions from waste-to-energy plants was justified by the 2007 status of emissions of French municipal solid waste incinerators (MSWIs). All emissions were examined, plant by plant, but this paper focuses on the incinerator emission that is most frequently mentioned in the French media, toxic dioxins and furans. The study showed that there are 85 large MSWI that generate electricity or heat, i.e., waste-to-energy (WTE) plants, and 39 smaller MSW incinerators. The results showed that all French MSWI are operated well below the EU and French standard of 0.1 ng TEQ Nm^?3 (toxic equivalent nanograms per standard cubic meter) and that their total dioxin/furan emissions decreased from 435 g TEQ in 1997 to only 1.2 g in 2008. All other industrial emissions of dioxins have also decreased and the major source is residential combustion of wood (320 g TEQ). It was extremely difficult to obtain MSWI emission data. This unwarranted lack of transparency has resulted in the public perception that MSWI plants are major contributors to dioxin emissions while in fact they have ceased to be so.     

Simple removal of dioxins by injecting combustion gas into water

A simple, low-cost method for suppression of dioxins/furans (hereinafter referred to as dioxins) is required because many middle- and, especially, small-scale incinerators have fallen into disuse or have been dismantled because of the high running and system costs of measures for the suppression of dioxins. Therefore, the purpose of the present study was to develop a simple removal method for dioxins from combustion gas and to evaluate the basic removal rate of dioxins. The removal method for suspended matter in a gas mixture (cold model) and dioxins in exhaust gases (hot model) has been investigated by means of gas injection into water, the mechanism of which is that the suspended matter in the gas gathers at the gas–liquid interface. In the cold model, the removal ratio of fine particles (R_P) by gas injection into water was reproduced well by the following equation: R_P (%) = 100 × {1−exp(−0.8 · S_S · t_C)}, where S_S (cm²/cm³) is the specific surface area of bubbles and t_C (s) is the residence time of bubbles in water. The removal ratio of fine particles increased as the product S_s · t_C increased. In a hot model using the exhaust gas from combustion experiments of polyvinyl chloride, the removal ratio of dioxins (R_D) by injecting the exhaust gas into water was estimated by the following equation: R_D (%) = 100 × {1−exp(−0.8 · S_S · t_C · C_D0 ^0.07)}, where C_D0 [ng/cm³ (at standard temperature and pressure)] is the dioxins concentration in the exhaust gas before injection into water. R_D depends greatly on the specific surface area of bubbles and the residence time of the bubbles in water, and only weakly on the dioxins concentration in the exhaust gas. Injection of the exhaust gas into water has been shown to be effective and was evaluated as a simple method for the removal of dioxins from exhaust gas.     

Experimental investigation of wood combustion in a fixed bed with hot air

Waste combustion on a grate with energy recovery is an important pillar of municipal solid waste (MSW) management in the Netherlands. In MSW incinerators fresh waste stacked on a grate enters the combustion chamber, heats up by radiation from the flame above the layer and ignition occurs. Typically, the reaction zone starts at the top of the waste layer and propagates downwards, producing heat for drying and devolatilization of the fresh waste below it until the ignition front reaches the grate. The control of this process is mainly based on empiricism.MSW is a highly inhomogeneous fuel with continuous fluctuating moisture content, heating value and chemical composition. The resulting process fluctuations may cause process control difficulties, fouling and corrosion issues, extra maintenance, and unplanned stops. In the new concept the fuel layer is ignited by means of preheated air (T > 220 °C) from below without any external ignition source. As a result a combustion front will be formed close to the grate and will propagate upwards. That is why this approach is denoted by upward combustion.Experimental research has been carried out in a batch reactor with height of 4.55 m, an inner diameter of 200 mm and a fuel layer height up to 1 m. Due to a high quality two-layer insulation adiabatic conditions can be assumed. The primary air can be preheated up to 350 °C, and the secondary air is distributed via nozzles above the waste layer. During the experiments, temperatures along the height of the reactor, gas composition and total weight decrease are continuously monitored. The influence of the primary air speed, fuel moisture and inert content on the combustion characteristics (ignition rate, combustion rate, ignition front speed and temperature of the reaction zone) is evaluated.The upward combustion concept decouples the drying, devolatilization and burnout phase. In this way the moisture and inert content of the waste have almost no influence on the combustion process. In this paper an experimental comparison between conventional and reversed combustion is presented.     

Energy from Waste – Clean,efficient, renewable: Transitions in combustion efficiency and NOx control

Traditionally EfW (Energy from Waste) plants apply a reciprocating grate to combust waste fuel. An integrated steam generator recovers the heat of combustion and converts it to steam for use in a steam turbine/generator set. This is followed by an array of flue gas cleaning technologies to meet regulatory limitations.Modern combustion applies a two-step method using primary air to fuel the combustion process on the grate. This generates a complex mixture of pyrolysis gases, combustion gases and unused combustion air. The post-combustion step in the first pass of the boiler above the grate is intended to “clean up” this mixture by oxidizing unburned gases with secondary air.This paper describes modifications to the combustion process to minimize exhaust gas volumes and the generation of noxious gases and thus improving the overall thermal efficiency of the EfW plant. The resulting process can be coupled with an innovative SNCR (Selective Non-Catalytic Reduction) technology to form a clean and efficient solid waste combustion system.Measurements immediately above the grate show that gas compositions along the grate vary from 10% CO, 5% H₂ and 0% O₂ to essentially unused “pure” air, in good agreement with results from a mathematical model. Introducing these diverse gas compositions to the post combustion process will overwhelm its ability to process all these gas fractions in an optimal manner. Inserting an intermediate step aimed at homogenizing the mixture above the grate has shown to significantly improve the quality of combustion, allowing for optimized process parameters. These measures also resulted in reduced formation of NO_x (nitrogenous oxides) due to a lower oxygen level at which the combustion process was run (2.6 vol% O_2, wet instead of 6.0 vol% O_2, wet).This reduction establishes optimal conditions for the DyNOR? (Dynamic NO_x Reduction) NO_x reduction process. This innovative SNCR technology is adapted to situations typically encountered in solid fuel combustion. DyNOR? measures temperature in small furnace segments and delivers the reducing reagent to the exact location where it is most effective. The DyNOR? distributor reacts precisely and dynamically to rapid changes in combustion conditions, resulting in very low NO_x emissions from the stack.     

Modeling and comparative assessment of municipal solid waste gasification for energy production

Gasification is the thermochemical conversion of organic feedstocks mainly into combustible syngas (CO and H₂) along with other constituents. It has been widely used to convert coal into gaseous energy carriers but only has been recently looked at as a process for producing energy from biomass. This study explores the potential of gasification for energy production and treatment of municipal solid waste (MSW). It relies on adapting the theory governing the chemistry and kinetics of the gasification process to the use of MSW as a feedstock to the process. It also relies on an equilibrium kinetics and thermodynamics solver tool (Gasify®) in the process of modeling gasification of MSW. The effect of process temperature variation on gasifying MSW was explored and the results were compared to incineration as an alternative to gasification of MSW. Also, the assessment was performed comparatively for gasification of MSW in the United Arab Emirates, USA, and Thailand, presenting a spectrum of socioeconomic settings with varying MSW compositions in order to explore the effect of MSW composition variance on the products of gasification. All in all, this study provides an insight into the potential of gasification for the treatment of MSW and as a waste to energy alternative to incineration.     

Experimental and kinetic modeling of oxygen-enriched air combustion of municipal solid waste

The characteristics of oxygen-enriched air combustion of raw municipal solid waste (MSW) were studied by thermogravimetric analysis. Experiments on oxidative pyrolysis of MSW were carried out under different atmospheres (N(2), N(2):O(2)=7:3, N(2):O(2)=5:5, N(2):O(2)=4:6, and N(2):O(2)=2:8) at 30 degrees C/min. Two distinct peaks of weight loss were obtained according to the derivative thermogravimetric curves; one of them is centered on 305 degrees C with about 40% weight loss, and the second is centered on 420 degrees C with about 20% weight loss. Effects of oxygen concentration on the decomposition process and char combustion were analyzed, and then the process of oxygen-enriched air combustion of MSW was divided into four steps. Kinetic parameters were observed by direct non-linear regressions. According to the obtained data, the apparent activation energy and reaction order decreases along with the combustion process, while that of char combustion increases as oxygen concentration increases.     

Effect of the mixing ratio on the composting of OFMSW digestate: assessment of compost quality

This study presents the results obtained in compostability tests of organic fraction of municipal solid waste (OFMSW) digestate. The final aim was to obtain mature compost without phytotoxic effects. For the evaluation of the composting process, a novel parameter describing the performance of the composting process, the relative heat generation standardized with the initial volatile solid content (RHGVS₀), was defined and evaluated at laboratory-scale. From these laboratory-scale test, the optimum operational conditions were obtained, a mixing ratio (v/v) of 1:1:0 (bulking agent:digestate:co-substrate) and with 15% of mature compost as inoculum. Subsequently, these optimum operational conditions were applied in the active phase of the composting pilot-scale reactor. The active composting stage took 7 days, subsequently a curing phase of 60 days was carried out at ambient conditions. After 30 days of curing, the mature compost showed a specific oxygen uptake rate (SOUR) of 0.14 mg O₂/g VS·h, a germination index (GI) of 99.63% and a low volatile fatty acids (VFA) concentration (41.3 AcH mg/kg_dm), being indicative of the good compost stability and maturity of the compost. The very good quality of the final compost obtained indicated that the RHGVS₀ accurately describes the performance of the composting process.

     

Treatment of municipal landfill leachate by catalytic wet air oxidation: Assessment of the role of operating parameters by factorial design

The wet air oxidation (WAO) of municipal landfill leachate catalyzed by cupric ions and promoted by hydrogen peroxide was investigated. The effect of operating conditions such as WAO treatment time (15-30 min), temperature (160-200 °C), Cu²⁺ concentration (250-750 mg L⁻¹) and H₂O₂ concentration (0-1500 mg L⁻¹) on chemical oxygen demand (COD) removal was investigated by factorial design considering a two-stage, sequential process comprising the heating-up of the reactor and the actual WAO. The leachate, at an initial COD of 4920 mg L⁻¹, was acidified to pH 3 leading to 31% COD decrease presumably due to the coagulation/precipitation of colloidal and other organic matter. During the 45 min long heating-up period of the WAO reactor under an inert atmosphere, COD removal values up to 35% (based on the initial COD value) were recorded as a result of the catalytic decomposition of H₂O₂ to reactive hydroxyl radicals. WAO at 2.5 MPa oxygen partial pressure advanced treatment further; for example, 22 min of oxidation at 200 °C, 250 mg L⁻¹ Cu²⁺ and 0-1500 mg L⁻¹ H₂O₂ resulted in an overall (i.e. including acidification and heating-up) COD reduction of 78%. Amongst the operating variables in question, temperature had the strongest influence on both the heating-up and WAO stages, while H₂O₂ concentration strongly affected the former and reaction time the latter. Nonetheless, the effects of temperature and H₂O₂ concentration were found to depend on the concentration levels of catalyst as suggested by the significance of their 3rd order interaction term.     

Sodium Persulfate Oxidation for the Remediation of Chlorinated Solvents (USEPA Superfund Innovative Technology Evaluation Program)

This study has been conducted at the University of Connecticut (UCONN) in connection with the USEPA Superfund Innovative Technology Evaluation (SITE) program to evaluate a chemical oxidation technology (sodium persulfate) developed at UCONN. A protocol to assess the efficacy of oxidation technologies has been used. This protocol, which consists of obtaining data from a treatability study, tested two in-situ chemical oxidation technologies that can be used on soil and groundwater at a site in Vernon, Connecticut. Based on the treatability report results and additional field data collected at the site, the design for the field implementation of the chemical oxidation remediation was completed. The results indicate that both sodium persulfate and potassium permanganate were able to effectively degrade the target VOCs (i.e., PCE, TCE and cis-DCE) in groundwater and soil-groundwater matrices. In the sodium persulfate tests (120 hrs), the extent of destruction of target VOCs was 74% for PCE, 86% for TCE and 84% for cis-DCE by Na₂S₂O₈ alone and 68% for PCE, 76% for TCE, and 69% for cis-DCE by Fe(II)-catalyzed Na₂S₂O₈. The results demonstrate the sodium persulfate's ability to degrade PCE, TCE and cis-DCE. It is expected that given sufficient dose and treatment time, a higher destruction rate of the dissolved phase contamination can be achieved. The data also indicates that the catalytic effect of the iron chelate on persulfate chemistry was much less pronounced in the soil-groundwater matrix. This indicates an interaction between the iron chelate solution and the soil, which may have resulted in a lower availability of the chelated iron for catalysis. The study showed that the remediation of the VOCs-contaminated soil and groundwater by in-situ chemical oxidation using sodium persulfate is feasible at the Roosevelt Mills site. As a result, the USEPA SITE program will evaluate this technology at this site.     

Polycyclic aromatic hydrocarbon (PAH) emission from co-firing municipal solid waste (MSW) and coal in a fluidized bed incinerator

Polycyclic aromatic hydrocarbons (PAH) emissions from a commercial municipal solid waste incinerator (MSWI) were studied. A MSW–coal mixture and coal only were used as fuel for the fluidized bed incinerator. Seven sampling points were chosen according to the classified four PAH emission pathways: flue gas, residue, ash and water. The mixture of MSW and coal resulted in PAH emission more than that of coal only, and PAH emission increased with increasing MSW mass percentage. Calcium oxide (CaO) or calcium carbonate (CaCO₃) was added as a desulfurizer. PAH emission also changed with different desulfurizers because of their different influences on heat balance. The PAH toxic equivalent (TEQ) of all operating conditions was also examined, showing that total daily PAH emission from MSWI can be determined.     

Decomposition of dichloromethane and in situ alkali absorption of resulting halogenated products by a packed-bed non-thermal plasma reactor

For an effective decomposition and removal of organic halogenated compounds, a packed-bed non-thermal plasma reactor with in situ absorption of the resulting halogenated products by alkaline sorbent incorporated was proposed. In the plasma reactor, α-Al₂O₃ particles of 1 and 3 mm (mean particle diameter) were packed as solid dielectric medium to enhance the plasma power density in the reactor. Further, alkaline sorbent of Ca(OH)₂ was doped onto the surface of α-Al₂O₃ particles, in order to remove halogenated products by in situ absorption with Ca(OH)₂. A high-voltage and high-frequency pulsed power of −15 to 15 kV and 1 kHz was applied to the wire electrode of the plasma reactor by means of a DC power source. In the present study, as the sample of an organic halogenated compound that is most popularly used, we selected dichloromethane (CH₂Cl₂), and 500 ppm of the initial concentration of CH₂Cl₂ was fed into the reactor accompanied by air at a fixed flow rate of 500 × 10⁻⁶ m³ min⁻¹ at room temperature. As a result, it was recognized that the amount of CH₂Cl₂ decomposed by non-thermal plasma in an α-Al₂O₃ particle bed increased with an increase in plasma input power. The ratio of decomposition of CH₂Cl₂ was almost 100% at 13 kV of electric power and 1 kHz frequency, and CO₂, CH₃Cl, COCl₂, HCl, and Cl₂ were observed as the major reaction products. On the other hand, when CH₂Cl₂ was introduced into the plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ were packed, the ratio of decomposition of CH₂Cl₂ became higher, compared to the case that α-Al₂O₃ particles were not doped with Ca(OH)₂. Moreover, there were no halogenated by-product gases detected in the outlet gas from the reactor. As the solid reaction products, CaClOH and Ca(ClO)₂·4H₂O were detected on Ca(OH)₂ by X-ray diffraction. From these findings, it was recognized that CH₂Cl₂ was decomposed more effectively without producing unwanted harmful halogenated by-products in the proposed non-thermal plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ sorbent were packed.     

Long Term Trends in Concentration of Major Pollutants (SO<Subscript>2</Subscript>, CO,NO, NO<Subscript>2</Subscript>, O<Subscript>3</Subscript> and PM<Subscript>10</Subscript>) in Prague – Czech Republic (Analysis of Data Between 1992 and 2005)

To assess the effect of changes in traffic density and fuels used for heating at the beginning of the 1990s, 1992–2005 monthly averages of PM₁₀, SO₂, NO₂, NO, CO and O₃ from Prague, the Czech capital, were analyzed together with long term trends in emissions of major pollutants, fuel consumption and number of vehicles registered in Prague. The data from all monitoring stations were retrieved from the database of the state automated monitoring system. Correlation coefficients between ambient monthly averaged temperature and all pollutants of concern showed distinct seasonal trends. The results showed that while SO₂ and to some extent also CO concentrations dropped namely in the first half of the analyzed period (1992–1997) as a result decreased fossil fuel consumption for local heating, the behaviour of other pollutant concentrations followed a different pattern. PM₁₀ concentrations decreased during the beginning of the 1990s but showed a sign of increase after 2000. Concentrations of ozone and NO₂ did not reveal any significant change throughout the whole studied period. It can be concluded that during the studied period traditional urban sources of pollution, such as coal and oil combustion, lost their importance but were simultaneously substituted by pollutants from automotive transport (namely PM and NO₂) making the problem of air quality even worse.     

Seasonal characterization of municipal solid waste (MSW) in the city of Chihuahua,Mexico

Management of municipal solid waste (MSW) has become a significant environmental problem, especially in fast-growing cities. The amount of waste generated increases each year and this makes it difficult to create solutions which due to the increase in waste generation year after year and having to identify a solution that will have minimum impact on the environment. To determine the most sustainable waste management strategy for Chihuahua, it is first necessary to identify the nature and composition of the city’s urban waste. The MSW composition varied considerably depending on many factors, the time of year is one of them. Therefore, as part of our attempt to implement an integral waste management system in the city of Chihuahua, we conducted a study of the characteristics of MSW composition for the different seasons. This paper analyzes and compares the findings of the study of the characterization and the generation of solid waste from households at three different socio-economic levels in the city over three periods (April and August, 2006 and January, 2007).The average weight of waste generated in Chihuahua, taking into account all three seasons, was 0.592 kg capita^?1 day^?1. Our results show that the lowest income groups generated the least amount of waste. We also found that less waste was generated during the winter season. The breakdown for the composition of the waste shows that organic waste accounts for the largest proportion (45%), followed by paper (17%) and others (16%).     

Treatment of MTBE‐Contaminated Waters with Fenton's Reagent

Methyl tertiary‐butyl ether (MTBE) is commonly used as a fuel additive because of its many favorable properties that allow it to improve fuel combustion and reduce resulting concentrations of carbon monoxide and unburnt hydrocarbons. Unfortunately, increased production and use have led to its introduction into the environment. Of particular concern is its introduction into drinking water supplies. Accordingly, research studies have been initiated to investigate the treatment of MTBE‐contaminated soil and groundwater. The summer 2000 issue of Remediation reported the results of an initial study conducted by the authors to evaluate the treatment of MTBE using Fenton's reagent. In this follow‐up study, experiments were conducted to further demonstrate the effectiveness of using Fenton's reagent (H₂O₂:Fe⁺²) to treat MTBE‐contaminated groundwater. The concentration of MTBE was reduced from an initial concentration of 1,300 μg/l (14.77 μ moles) to the regulatory level of 20 μg/l (0.23 μ moles) at a H₂O₂:Fe⁺² molar ratio of 1:1, with ten minutes of contact time and an optimum pH of 5. The by‐products, acetone and tertiary butyl alcohol, which are always present in MTBE in trace amounts, were not removed even after 60 minutes of reaction time. © 2002 Wiley Periodicals, Inc. *     

Construction and evaluation of simulated pilot scale landfill lysimeter in Bangladesh

This research concentrates the design, construction and evaluation of simulated pilot scale landfill lysimeter at KUET campus, Khulna, Bangladesh. Both the aerobic and anaerobic conditions having a base liner and two different types of cap liner were simulated. After the design of a reference cell, the construction of landfill lysimeter was started in January 2008 and completed in July 2008. In all construction process locally available civil construction materials were used. The municipal solid waste (MSW) of 2800–2985 kg having the total volume of 2.80 m³ (height 1.6 m) and moisture content of 65% was deposited in each lysimeter by applying required compaction energy. In contrast, both the composition in terms of methane (CH₄), carbon dioxide (CO₂) and oxygen (O₂) as well as the flow rate of landfill gas (LFG) generated from MSW in landfill lysimeter were measured and varied significantly in relation to the variation of lysimeter operational condition. Moreover, anaerobic lysimeter-C shows the highest composition of LFG in compare to the anaerobic lysimeter-B due to the providing of lower compaction of cap liner in anaerobic lysimeter-C. Here, it is interesting to note that in absence of compacted clay liner (CCL) and hence percolation of rainwater that facilitates rapid degradation of MSW in aerobic lysimeter-A has resulted in the highest settlement than that of anaerobic landfill lysimeter-B and C. Moreover, in case of anaerobic lysimeter-B and C, the leachate generation was lower than that of aerobic lysimeter-A due to the providing of cap liner in anaerobic lysimeter-B and C, played an important role to reduce the percolation of rainwater. The study also reveals that the leachate pollution index (LPI) has decreased in relation to the increasing of elapsed period as well as the LPI for collection system of aerobic lysimeter-A was higher than that of the collection system of anaerobic lysimeter-B and C. Finally, it can be depicted that LPI for lysimeter was significantly high and proper treatment will be necessary before discharging the lysimeter leachate into the water bodies.