Driving forces for import of waste for energy recovery in Sweden.

Between 1996 and 2002, the Swedish import of so-called yellow waste for energy recovery increased. The import mainly consisted of separated wood waste and mixes of used wood and paper and/or plastics that was combusted in district heat production plants (DHPPs). Some mixed waste was imported to waste incineration plants for energy recovery (10% of the import of yellow waste for energy recovery in 2002). The import came primarily from Germany, the Netherlands, Norway, Denmark and Finland. We identified six underlying driving forces for this recent increase of imported waste which are outlined and their interactive issues discussed. --The energy system infrastructure, which enables high energy recovery in Sweden. --The energy taxation, where high Swedish taxes on fossil fuels make relatively expensive solid biofuels the main alternative for base load production of district heat. --The quality of the waste-derived fuels, which has been higher in the exporting countries than in Sweden. --The bans on landfilling within Europe and the shortage of waste treatment capacity. --Taxes on waste management in Europe. --Gate fee differences between exporting countries and Sweden. In the future, the overall strength of these driving forces will probably be weakened. A Swedish tax on waste incineration is being investigated. In other European countries, the ambition to reach the Kyoto targets and increase the renewable electricity production could improve the competitiveness of waste-derived fuels in comparison with fossil fuels. Swedish DHPPs using waste-derived fuels will experience higher costs after the Waste Incineration Directive is fully implemented. The uncertainty about European waste generation and treatment capacity, however, might have a large influence on the future gate fees and thus also on the yellow waste import into Sweden.     

Estimation of nitrogen flow change in Beijing,China, for the years 1995, 2000, and 2004

Rapid economic growth in China has led to environmental pollution. Recycling nutrients is essential for sustainable agriculture, and it is necessary to estimate the amount of available organic resources in order to achieve this. Using nitrogen as a tracer, we estimated the organic resource flows in 1995, 2000, and 2004 in Beijing. The agricultural nitrogen flow was calculated from the fertilizer, agricultural product, and byproduct flows. The livestock nitrogen flow was calculated from the feed, excretion, and stock flows. The human nitrogen flow was calculated from the food intake, excretion, and food waste flows. The amounts of recyclable organic resources were estimated from these nitrogen flows. The Daxing, Fangshan, Miyun, Shunyi, and Tongzho areas had high nitrogen loads in 2004, as did the outer suburbs, but Beijing proper had an extremely low nitrogen flow and the inner suburbs had low nitrogen flows. The estimated amount of compost that could be produced from domestic organic waste across Beijing was equivalent to 88,100 t of nitrogen. The Beijing area contains 394,100 ha of farmland, so, if the compost was applied at an equivalent of 100 kg of nitrogen per hectare, the equivalent of 48,000 t of nitrogen would be surplus.     

Demand for waste as fuel in the swedish district heating sector: a production function approach

This paper evaluates inter-fuel substitution in the Swedish district heating industry by analyzing almost all the district heating plants in Sweden in the period 1989-2003, specifically those plants incinerating waste. A multi-output plant-specific production function is estimated using panel data methods. A procedure for weighting the elasticities of factor demand to produce a single matrix for the whole industry is introduced. The price of waste is assumed to increase in response to the energy and CO2 tax on waste-to-energy incineration that was introduced in Sweden on 1 July 2006. Analysis of the plants involved in waste incineration indicates that an increase in the net price of waste by 10% is likely to reduce the demand for waste by 4.2%, and increase the demand for bio-fuels, fossil fuels, other fuels and electricity by 5.5%, 6.0%, 6.0% and 6.0%, respectively.     

Energy recovery from solid waste fuels using advanced gasification technology

Since the mid-1980s, TPS Termiska Processer AB has been working on the development of an atmospheric-pressure gasification process. A major aim at the start of this work was the generation of fuel gas from indigenous fuels to Sweden (i.e. biomass). As the economic climate changed and awareness of the damage to the environment caused by the use of fossil fuels in power generation equipment increased, the aim of the development work at TPS was changed to applying the process to heat and power generation from feedstocks such as biomass and solid wastes. Compared with modern waste incineration with heat recovery, the gasification process will permit an increase in electricity output of up to 50%. The gasification process being developed is based on an atmospheric-pressure circulating fluidised bed gasifier coupled to a tar-cracking vessel. The gas produced from this process is then cooled and cleaned in conventional equipment. The energy-rich gas produced is clean enough to be fired in a gas boiler (and, in the longer term, in an engine or gas turbine) without requiring extensive flue gas cleaning, as is normally required in conventional waste incineration plants. Producing clean fuel gas in this manner, which facilitates the use of efficient gas-fired boilers, means that overall plant electrical efficiencies of close to 30% can be achieved. TPS has performed a considerable amount of pilot plant testing on waste fuels in their gasification/gas cleaning pilot plant in Sweden. Two gasifiers of TPS design have been in operation in Grève-in-Chianti, Italy since 1992. This plant processes 200 tonnes of RDF (refuse-derived fuel) per day. It is planned that the complete TPS gasification process (including the complete fuel gas cleaning system) be demonstrated in several gas turbine-based biomass-fuelled power generating plants in different parts of the world. It is the aim of TPS to prove, at commercial scale, the technical feasibility and economic advantages of the gasification process when it is applied to solid waste fuels. This aim shall be achieved, in the short-term, by employing the cold clean product gas in a gas boiler and, in the longer-term, by firing the gas in engines and gas turbines. A study for a 90 MWth waste-fuelled co-generation plant in Sweden has shown that, already today, gasification of solid waste can compete economically with conventional incineration technologies.     

Review of municipal solid waste management options in Malaysia,with an emphasis on sustainable waste-to-energy options

A beautiful and clean environment is the desire of every society. Malaysia is facing an uncontrolled increase in municipal solid waste (MSW) generation due to population growth, economic advancement, and industrialization, but the current, most common waste disposal practice of landfilling is not sustainable. The increasing standard of living also saps more energy from the power generation systems in which fossil fuels are the major source of fuel for the plants. Malaysia generates about 0.5–1.9 kg/capita/day of MSW; a total of about 25,000 tonnes/day of MSW is currently generated and is estimated to exceed 30,000 tonnes/day by 2020. Malaysian MSW is mainly composed of 45 % food waste, 24 % plastic, 7 % paper materials, 6 % metal, 4 % wood and 3 % glass, which are commingled, and is thus characterised by 52–66 % moisture content. Currently, 80–95 % of collected MSW is landfilled and 5 % is recycled, while composting and energy recovery are rarely practiced. This paper reviews the solid waste practice in Malaysia and looks into alternative management options for sustainability. Malaysia MSW represents recyclable power and energy potential if properly sorted. This study considered the practice of sorting at the source and the use of combustible MSW components as fuel to generate heat for a hybrid solar, flue gas, chimney power plant.     

Long-term consequences of non-intentional flows of substances: Modelling non-intentional flows of lead in the Dutch economic system and evaluating their environmental consequences

Substances may enter the economy and the environment through both intentional and non-intentional flows. These non-intentional flows, including the occurrence of substances as pollutants in mixed primary resources (metal ores, phosphate ores and fossil fuels) and their presence in re-used waste streams from intentional use may have environmental and economic consequences in terms of pollution and resource availability. On the one hand, these non-intentional flows may cause pollution problems. On the other hand, these flows have the potential to be a secondary source of substances.This article aims to quantify and model the non-intentional flows of lead, to evaluate their long-term environmental consequences, and compare these consequences to those of the intentional flows of lead. To meet this goal, the model combines all the sources of non-intentional flows of lead within one model, which also includes the intentional flows.Application of the model shows that the non-intentional flows of lead related to waste streams associated with intentional use are decreasing over time, due to the increased attention given to waste management. However, as contaminants in mixed primary resources application, lead flows are increasing as demand for these applications is increasing.     

Improving the layout of recycling centres by use of lean production principles

There has been increased focus on recycling in Sweden during recent years. This focus can be attributed to external environmental factors such as tougher legislation, but also to the potential gains for raw materials suppliers. Recycling centres are important components in the Swedish total recycling system. Recycling centres are manned facilities for waste collection where visitors can bring, sort and discard worn products as well as large-sized, hazardous, and electrical waste. The aim of this paper was to identify and describe the main flows and layout types at Swedish recycling centres. The aim was also to adapt and apply production theory for designing and managing recycling centre operations. More specifically, this means using lean production principles to help develop guidelines for recycling centre design and efficient control.Empirical data for this research was primarily collected through interviews and questionnaires among both visitors and employees at 16 Swedish recycling centres. Furthermore, adapted observation protocols have been used in order to explore visitor activities. There was also close collaboration with a local recycling centre company, which shared their layout experiences with the researchers in this project.The recycling centres studied had a variety of problems such as queues of visitors, overloading of material and improper sorting. The study shows that in order to decrease the problems, the recycling centres should be designed and managed according to lean production principles, i.e. through choosing more suitable layout choices with visible and linear flows, providing better visitor information, and providing suitable technical equipment. Improvements can be achieved through proper planning of the layout and control of the flow of vehicles, with the result of increased efficiency and capacity, shorter visits, and cleaner waste fractions. The benefits of a lean production mindset include increased visitor capacity, waste flexibility, improved sorting quality, shorter time for visits and improved working conditions.     

Substance Flow Analysis and Source Mapping of Chemical UV-filters

Chemical ultraviolet (UV)-filters are used in sunscreens to protect the skin from harmful UV radiation which may otherwise cause sunburns and skin cancer. Commonly used chemical UV-filters are known to cause endocrine disrupting effects in both aquatic and terrestrial animals as well as in human skin cells. Here, source mapping and substance flow analysis were applied to find the sources of six UV-filters (oxybenzone, avobenzone, 4-methylbenzylidene camphor, octyl methoxycinnamate, octyl dimethyl PABA and homosalate) and to identify the most dominant flows of these substances in Denmark. Urban water, composed of wastewater and surface waters, was found to be the primary recipient of UV-filters, whereby wastewater received an estimated 8.5–65 tonnes and surface waters received 7.1–51 tonnes in 2005. In wastewater treatment plants, their sorption onto sludge is perceived to be an important process and presence in effluents can be expected due to a lack of biodegradability. In addition, the use of UV-filters is expected to continue to increase significantly. Not all filters (e.g., octyl dimethyl PABA and homosalate) are used in Denmark. For example, 4-MBC is mainly associated with self-tanning liquids and private import of sunscreens.     

Anthropogenic metal cycles in China

The flows and stocks of seven important industrial metals were characterized for mainland China for several years in the dynamically changing decade of 1994–2004. One-year snapshot cycles are provided for chromium, nickel, and silver. For copper, zinc, lead, and iron, multiple-year cycles have been completed; they demonstrate that the flows of these metals into use in China doubled between 2000 and 2004. Although the Chinese per capita flows from production to disposal are mostly shown to be below the global average rate, they are increasing or are expected to increase dramatically. The metal resource efficiency is evaluated for several indicators of material flow analysis; these metrics for China are also below the global average values. The research quantitatively illustrates that China’s metal cycles may pose significant resource and environmental challenges in terms of their magnitudes and potential for growth.     

Substance Flow Analyses of Organic Pollutants in Stockholm

This paper summarizes substance flow analyses for four organic substances in the City of Stockholm, Sweden: diethylhexyl phthalate (DEHP), alkylphenolethoxylates (APEO), polybrominated diphenylethers (PBDE) and chlorinated paraffins (CP). The results indicate that the stocks of APEO, PBDE and CP all are approximately 200–250 tonnes, whereas the DEHP stock is two orders of magnitude larger. Emissions can be linked to imported consumer goods such as electronics (PBDE) and textiles (APEO), and to construction materials (DEHP, CP). For several of the substances considerable amounts remain in the technosphere for a long time, even after use of the substance in new products has been eliminated. For example, the use of DEHP as plasticizer for PVC plastics in cables and floorings has more or less been phased-out, but still these applications make up a stock of some 20,000 tonnes (85% of the total DEHP stock in Stockholm) and emit 28 tonnes of DEHP annually (93% of overall emissions). Likewise, the use of chlorinated paraffins in sealants has been radically reduced, but there are 170 tonnes of CP in sealants in Stockholm making up 75% of the stock, and causing half of the emissions to water and air. These emissions are likely to continue for decades, and the stocks therefore have to be considered when analysing and managing the impact of urban substance flows on the environment.     

Methods for determining the biomass content of waste.

As CO2 emission trading in Europe has been established it is of essential importance to distinguish between biogenic and fossil emissions. Emissions resulting from bio-fuels and biogenous fractions are categorized as climate-neutral. Determination of plants using only fossil or bio-fuels is simple but categorization becomes more difficult for plants using a mix of fossil and bio-fuel such as solid recovered fuels. In the meantime, different methods for solving this problem have been developed. Using different approaches and technologies, all of these methods have the same goal: determining the biomass content (biogenic fraction), for example, in solid recovered fuels or in the off-gas of a mono- or co-incineration plant in order to calculate the biogenic carbon dioxide emissions. In the following article, the most common methods for determining the biogenic fraction of fuels, namely the Selective Dissolution Method, the Balance Method and the 14C-Method will be explained in detail.     

Catalytic co-pyrolysis of <Emphasis Type="Italic">Pterospermum acerifolium</Emphasis> and plastic waste

The continuous increase in generation of solid wastes and gradual declining of fossil fuels necessities the development of sustainable conversion technologies. Recent studies have shown that the addition of biomass with hydrogen-rich co-reactants (plastics) altogether enhances the quality of bio-fuels using pyrolysis process. It was observed that red mud (which is produced as by-product in Bayer process) was used as a catalyst in few conversion process. In this study, pyrolysis of biomass (Pterospermum acerifolium) and waste plastic mixture with activated red-mud catalyst was investigated using thermo-gravimetric analysis. The kinetic parameters (activation energy and pre-exponential factor) of this process were determined using distributed activation energy model (DAEM). The DAEM was effectively applied to decide the activation energy (E) and pre-exponential factor (A) for each sample at various conversions during the catalytic co-pyrolysis. The biomass, plastic, biomass–plastic, and biomass–plastic–catalyst exhibited activation energies in the ranges of 78–268, 172–218, 67–307, and 202–292 kJ/mol, respectively.     

Life cycle assessment of solid refuse fuel production from MSW in Korea

Solid refuse fuel (SRF) produced from waste materials is a promising fuel that can be utilized for energy recovery in industries. This study considered both characterization and weighting modeling as life cycle assessment (LCA) results. This study aimed to analyze the flows of materials and energy and to evaluate the environmental impact of SRF plants using LCA and compared them with an incineration plant. Based on the results of material and energy flow analysis, SRF products had various energy potentials depending on the treatment method of municipal solid waste (MSW) and replaced the current fossil fuels by SRF combustion. Global impacts were mainly influenced by energy consumption, especially drying methods in the production of SRF, and affected the results of the weighting analysis. The SRF plant with a bio-drying option was evaluated as the best effective practice in the weighting analysis. The LCA results in this study indicated 0.021–9.88 points according to drying methods for SRF production and 1.38 points for incineration. In the sensitivity analysis, the environmental impact of SRF production was found to be significantly affected by the drying methods for MSW and the utilization of fossil energy. Thus, improvement of the drying options could significantly reduce the environmental impact.     

Recycling of plastic packaging waste in Bandung City,Indonesia

Economic growth, changing consumption and production patterns are resulting in rapid increase in the generation of plastic wastes, including plastic packaging waste (PPW). A variety of PPW is identified in the municipal solid waste (MSW) stream. In this paper, quantity and composition of PPW at generators (residential and nonresidential sectors) and at the informal sector of waste recycling were measured, and accordingly the flow of PPW within Bandung City, Indonesia was analyzed. Though the generation rate per capita is not so high (25.1 g per day), total PPW generated by 2.3 million inhabitants in Bandung becomes 58.4 tonnes per day (3.76 % of total MSW generated). Due to lack of integrated MSW management, most of PPW is neither collected properly nor disposed of in appropriate manner by the municipality. Collection of valuable wastes including PPW is done predominantly by the informal sector without regard to health and safety. It is predicted that total PPW recycled by various informal waste recycling players like scavengers, junkmen, intermediates, and dealers is 27.5 tonnes per day (64.6 % of total PPW generated). Interviews regarding the existing handling methods and incentives preferred by generators to increase the recycling rate are also presented.     

Quantitative Environmental Footprints and Sustainability Evaluation of Contaminated Land Remediation Alternatives for Two Case Studies

Since the US Environmental Protection Agency (US EPA) launched its “green remediation” program and EU member states began to reassess their national regulations for environmental remediation in order to reach a Europe‐wide consensus on policy and standards, the need and interest for sustainable remediation of contaminants from brownfields has grown considerably. Concomitantly, the ability to calculate and assess the suitability as well as the environmental footprints and associated risks of a growing number of remediation techniques has become a priority. The authors quantitatively evaluate the differences between various remediation techniques, and for this purpose, a number of ex situ and in situ remediation techniques are adapted to model 21 remediation scenarios for two contaminated sites in the Gothenburg region of Sweden: the Bohus Varv site on the Göta älv river bank and the Hexion site in Mölndal. A wide range of quantitative results for these models are presented, compared, and analyzed. Based on the results from both projects, it is concluded that: (1) remediation techniques requiring long distance residual transportation have significant footprints, except the transportation of contaminated residuals by train due to Swedish energy production conditions; (2) residual transportation by ship results in much higher SO_x, NO_x, and particle releases compared to the other alternatives; and (3) residual transporation by truck results in high accident risks. Finally, activities powered by electricity result in a reduced footprint compared to activities powered by fossil fuels, considering Swedish energy production conditions. The authors conducted a cross‐benefit analysis of SiteWise^TM applications which recognizes its potential as a tool for presenting life cycle assessment analyses with appropriate system boundary definitions and an easy inventory analysis process. Results from this tool provide valuable support to decision makers aiming at more sustainable remediation. © 2013 Wiley Periodicals, Inc.     

Dechlorination and decomposition of Aroclor 1242 in real waste transformer oil using a nucleophilic material with a modified domestic microwave oven

This research was done to assess the dechlorination and decomposition of polychlorinated biphenyls (PCBs) in real waste transformer oil through a modified domestic microwave oven (MDMW). The influence of microwave power (200–1000 W), reaction time (30–600 s), polyethylene glycol (PEG) (1.5–7.5 g), iron powder (0.3–1.5 g), NaOH (0.3–1.5 g), and H₂O (0.4–2 ml) were investigated on the decomposition efficiency of PCBs existing in real waste transformer oil with MDMW. Obtained data indicate that PEG and NaOH have the greatest influence on decomposition of PCBs; while, iron did not influence, and H₂O decreased, the decomposition efficiency of PCBs. Experimental data also indicated that with the optimum amount of variables through a central composites design method (PEG = 5.34 g, NaOH = 1.17 g, Fe = 0.6 g, H₂O = 0.8 ml and microwave power 800 W), 78 % of PCBs was degraded at a reaction time of about 6 min. In addition, the PCBs decomposition without using water increased up to 100 % in the reactor with the MDMW at 6 min. Accordingly, results showed that MDMW was a very efficient factor for PCBs decomposition from waste transformer oil. Also, using microwave irradiation, availability and inexpensive materials (PEG, NaOH), and iron suggest this method as a fast, effective, and cheap method for PCB decomposition of waste oils.     

Quality control of waste to incineration--waste composition analysis in Lidk?ping, Sweden.

In order to decrease environmental impacts in waste management the choice of treatment method must be based on the characteristics of the waste. Present sampling procedures do not provide statistically representative samples of solid waste and this provides difficulties in characterization. The objective of this study was to develop a procedure for waste component analysis and sampling of waste after collection and at plant level. A further objective was to characterize the waste delivered to an incineration plant for physical and chemical properties and to determine the amounts of delivered waste that could be classified as biofuels and fossil fuels. The proportions of recyclables and hazardous waste were also examined. Samples were taken randomly from waste trucks and divided by square implementation. Statistical analysis of the results showed that the number of sub-samples could be decreased with only a moderate increase in the confidence interval. This means that future waste composition analyses could be made more efficient and thereby less expensive. The analysis of the waste delivered to the Lidk?ping incineration plant (Central Sweden) showed that 66.4% of the household waste was composed of biofuels and 21.3% of non-renewable combustibles, of which 40.3% were recyclables. In addition, 11.6% of the household waste was non-combustible and 0.6% hazardous waste. The heat value for the biofuels was 18.0-19.7 MJ kg(-1) dry mass (DM) and for the fossil fuels 28.2-33.9 MJ kg(-1) DM. The industrial waste consisted of 35.9% biofuels, 62.0% fossil fuels, 1.6% non-combustible and 0.5% hazardous waste. The heat value was 19.5 MJ kg(-1) DM for the biofuels and 31.4 MJ kg(-1) DM for the fossil fuels.     

Material flow analysis of used personal computers in Japan

Most personal computers (PCs) are discarded by consumers after the data files have been moved to a new PC. Therefore, a used PC collection scheme should be created that does not depend on the distribution route of new PCs. In Japan, manufacturers’ voluntary take-back recycling schemes were established in 2001 (for business PCs) and 2003 (for household PCs). At the same time, the export of used PCs from Japan increased, affecting the domestic PC reuse market. These regulatory and economic conditions would have changed the flow of used PCs.In this paper, we developed a method of minimizing the errors in estimating the material flow of used PCs. The method’s features include utilization of both input and output flow data and elimination of subjective estimation as much as possible. Flow rate data from existing surveys were used for estimating the flow of used PCs in Japan for fiscal years (FY) 2000, 2001, and 2004. The results show that 3.92 million and 4.88 million used PCs were discarded in FY 2000 and 2001, respectively. Approximately two-thirds of the discarded PCs were disposed of or recycled within the country, one-fourth was reused within the country, and 8% were exported. In FY 2004, 7.47 million used PCs were discarded. The ratio of domestic disposal and recycling decreased to 37% in FY 2004, whereas the domestic reuse and export ratios increased to 37% and 26%, respectively. Flows from businesses to retailers in FY 2004 increased dramatically, which led to increased domestic reuse. An increase in the flow of used PCs from lease and rental companies to secondhand shops has led to increased exports. Results of interviews with members of PC reuse companies were and trade statistics were used to verify the results of our estimation of domestic reuse and export of used PCs.     

Kinetics of peanut shell pyrolysis and hydrolysis in subcritical water

Biomass is recognized as an important solution to energy and the environmental problems related to fossil fuel usage. The rational utilization of biomass waste is important not only for the prevention of environmental issues, but also for the effective utilization of natural resources. Pyrolysis and hyrolysis in subcritical water are promising processes for biomass waste conversion. This paper deals with hydrolysis and pyrolysis of peanut shells. Hydrolysis and pyrolysis kinetics of peanut shell wastes were investigated for the in-depth exploration of process mechanisms and for the control of the reactions. Hydrolysis kinetics was conducted in a temperature range of 180–240 °C. A simplified kinetic model to describe the hydrolysis of peanut shells was proposed. Hydrolysis activation energy as well as the pre-exponential factor was determined according to the model. The target products of peanut shell hydrolysis, reducing sugars, can reach up to 40.5 % (maximum yield) at 220 °C and 180 s. Pyrolysis characteristics were investigated. The results showed that three stages appeared in this thermal degradation process. Kinetic parameters in terms of apparent pyrolysis activation energy and pre-exponential factor were obtained by the Coats–Redfern method.     

Potential e-waste generated from households in Indonesia using material flow analysis

Waste of electronic and electrical equipment (e-waste) generated in Indonesia is expected to increase due to high growth of the Indonesian economy and fast development in technology. As Indonesia has not yet had specified criteria on e-waste, in this study, e-waste is defined as any obsolete or unwanted electronic and electrical equipment that is introduced into the recycling and disposal process. The objective of this study is to estimate the e-waste generated in Indonesian households using the method of material flow analysis. The amount of generated e-waste could be used for constructing an e-waste recycling management system in Indonesia. E-waste materials that need to be treated could be known. In this study, some types of equipment, such as television, washing machine, refrigerator, personal computer, and mobile phone, were chosen to be tracers. Using the modified material flow analysis model proposed by Steubing et al. (Waste Manage 30:473–482, 38), the potential e-waste that was generated from households was estimated. The total estimated accumulation of generated e-waste from households in 2015 and 2025 is about 285,000 and 622,000 tonnes, respectively. If a proper recycling system was in place, a new source for valuable materials recovery would be created, as well as protecting the environment and health.