臭氧氧化法处理焦化废水生化出水的反应动力学

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究，结果表明，在臭氧投加量为8．50mg／min，反应温度为20＇E和初始pH为10．61条件下，对COD的降解符合表观一级反应动力学模型，其相关系数R。=0．9991，表观反应速率常数k。。=1．01×10^-3s-1。该条件下，臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4．25～12．75mg／min）、不同的反应温度（10～40℃）和不同的初始pH（3．76～12．53）下，COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大，COD降解的表观反应速率常数从（0．554×10^-3）s-1增加到（1．06×10＆-3）s-1；随着反应温度的升高，表观反应速率常数从（0．427×10^-3）s-1增加到（1．40×10-3）s-1，温度越高反应速率提高的幅度却越小；在初始pH3．76～10．61范围内，表观反应速率常数从（0．218×10^-3）s-1增加到（1．01×10^-3）s-1，在初始pH为12．53时表观反应速率常数下降到（0．857×10^-3）s-1。     

真空紫外光臭氧降解偏二甲肼的研究

研究比较了臭氧氧化（O₃）、紫外臭氧（O₃/UV）和真空紫外臭氧（O₃/VUV）对推进剂——偏二甲肼的处理效果，O₃/VUV最为有效，反应速率常数分别比O₃/UV和O₃高39.8%和65.6%，中间产物——甲醛去除得更迅速，反应50 min即无法检出。初始pH 9时，O₃/VUV降解偏二甲肼的速率最快，达到0.4461 min^-1；反应速率常数随臭氧投加量的增加而线性增大；随偏二甲肼初始浓度从100 mg/L增加到2 000 mg/L，反应动力学由一级转为零级。碳酸盐浓度在0～2 mmol/L范围内对O₃/VUV降解偏二甲肼没有明显的抑制作用。偏二甲肼的无机氮产物以氨离子为主，无机氮只占总氮的40%～60%，说明仍有相当比例的氮以有机氮形式存在。     

一种包埋微生物复合填料的制备及性能评价简

采用包埋法制备出一种复合生物填料，测其各项理化性质，并以NO_x模拟废气验证其脱硝性能。填料主要由碳酸钙、牛粪堆肥腐殖质、菌剂载体、水泥、轻质珍珠岩、立体网状纤维及脱硝功能微生物等复合而成，粒径12 mm×20 mm，自然堆积密度（471±0.8）kg/m³，持水量（49±1.3）%，比表面积3.91 m²/g，平均机械强度（427.3±0.2）N，pH为10.5±0.2。填料能长期在潮湿环境中保持良好的粘结强度，并具有营养缓释及pH缓冲能力。包埋脱硝功能微生物复合填料中初期微生物数量5.3 ×10⁵ CFU/g，运行60 d后微生物数量达到8.6×10⁸ CFU/g，闲置停运30 d微生物有所减少，但重启后净化效率基本不变。当进气负荷低于1 878 mg/（m³·h），气体停留时间为14.47 s时，BF₁的去除率高达93.15%。     

铈离子光催化降解茜素绿的性能和机理简

主要研究了简单铈离子（Ce³⁺）在紫外光（UV）的作用下对蒽醌染料茜素绿（AG）的光催化降解效果和反应机理。结果表明，UV/Ce³⁺体系能够有效降解AG，初始反应速率随AG浓度的倒数值和Ce³⁺浓度的增加而线性增加，随初始溶液pH的增加先降低后增加，在酸性条件下有很高的TOC去除率。荧光探针实验表明，反应过程中可以产生·OH自由基。UV/Ce³⁺体系对其他类型染料和对硝基苯酚都有较好的降解效果。     

Fe0/厌氧微生物体系降解2,4,6-三氯酚特性研究

通过摇床间歇实验，研究了厌氧微生物与零价铁（Fe⁰）联合体系降解2,4,6-三氯酚（TCP）的特性，结果表明，在pH 7.5，35℃，150 r/min，Fe⁰ 10 g/L条件下，TCP初始浓度为30 mg/L时，TCP降解的拟一级反应速率常数为0.0207 h^-1，添加少量碳源可达到0.0390 h^-1，其降解速率是前者的1.88倍；添加碳源的体系在220 h内连续多次投加TCP降解率都达到80%以上，而不加碳源的体系在第2次投加TCP后降解率就只有30%左右；添加不同碳源，降解速率不同；添加2-溴乙烷磺酸钠（BESA）以及SO^2-₄、NO^-₃和S^2-对TCP降解有不同的抑制作用。     

不同基质共代谢降解2,4,6-三硝基苯酚的研究

以葡萄糖、可溶性淀粉、乙酸钠和苯酚作为共基质，通过35℃恒温生化培养箱缺氧驯化污泥，间歇恒温振荡试验研究了在不同共代谢基质条件下，2,4,6-三硝基苯酚（TNP）的缺氧降解性能。结果表明，经过驯化的微生物加入葡萄糖和苯酚作为碳源，在TNP∶苯酚∶葡萄糖为10∶3∶100的比例下，TNP生物降解率可以从不加碳源时的31.2%提高到86.6%；不同共基质条件下TNP的降解均符合一级反应动力学方程，反应速率常数大小依次是K_苯酚＜K_葡萄糖＜K_{葡萄糖+苯酚}，其中葡萄糖和苯酚同时作为共基质时TNP降解速率常数最大为0.019 h^-1。     

臭氧/Mn2+催化降解水溶液中的2,4-二氯苯氧乙酸

以Mn2 为催化剂与臭氧联合降解除草剂2,4-二氯苯氧乙酸(2,4-D).考察了反应温度、pH、2,4-D初始浓度和臭氧气体流量等因素对2,4-D降解效果的影响.pH对2,4-D降解效果影响很大,当pH=2.0、反应5 min时,2,4-D的去除率达99.8%;当pH=10.1、反应20min时,2,4-D的去除率仅为50.0%.反应温度升高、臭氧气体流量增加、2,4-D初始浓度降低均有助于2,4-D降解速率的提高.单独臭氧氧化2,4-D的表观反应速率常数为0.170 min-1;催化臭氧氧化2,4-D的表观反应速率常数为0.295min-1,是单独臭氧氧化的1.74倍.2,4-D的Mn2 催化臭氧反应遵循拟一级反应动力学方程.     

中试螺旋式自循环厌氧反应器处理安乃近制药废水的稳定性能简

以制药废水实验了50 m³螺旋式厌氧反应器（SPAC反应器）的稳定性。采用Augmented Dickey-Fuller（ADF）单位根检验表明，螺旋式反应器具有良好的启动和运行稳定性。负荷冲击实验显示，SPAC反应器具有较好的耐浓度冲击能力和耐水力冲击能力，所能耐受的最大浓度冲击强度大于60 000 （mg·h）/L（进水浓度提升2倍），所能耐受的最大水力冲击强度为300（m³·h）/d（进水流量提升50%）。SPAC反应器还具备受扰恢复能力。在反应液pH低于5.74，出水浓度、COD去除率和容积COD去除速率（VRR）分别为3 500 mg/L、22.30%和2.52 kg/（m³·d）的工况下，经过30 d恢复，出水浓度、COD去除率和VRR的恢复程度达到80%~90%。     

多级厌氧法处理螺旋霉素工业发酵菌渣效果的研究简

通过自主设计的多级厌氧反应器系统来考察半连续处理螺旋霉素工业发酵菌渣的效果。该系统总反应体积为44 L，由4个11 L的升流式厌氧反应罐组成，罐体间采用串联方式连接。121 d的连续运行周期分为3个阶段，各阶段的有机负荷率分别为1.27、1.82和2.73 kg COD/（m³·d）。全过程中主要监测了各级罐体的产气量和螺旋霉素的降解。结果表明，多级厌氧反应器系统启动初期会出现产气不稳定现象，经过2个月的运行之后系统达到稳定状态。在有机负荷达到2.73 kg COD/（m³·d）时，各级罐体仍能稳定运行，总产气的45%集中在1号罐。在系统启动初期，螺旋霉素不能被明显降解。运行约80 d后，整个体系达到了快速降解螺旋霉素的状态，在2.73 kg COD/（m³·d）的有机负荷率下，螺旋霉素降解率达到97%，同时可溶性COD降解率也达到了90%。     

自养反硝化菌对硝酸盐氮去除动力学及影响因素研究

为更经济有效地去除污水中的硝酸盐，从兼性污泥中分离获得6株能氧化单质硫和还原硝酸盐的自养反硝化菌。根据各菌株的降解曲线筛选出优势菌种N-I，并研究影响菌株N-I降解性能的环境因素，如pH、温度、碳源及硝酸盐的降解动力学。实验表明，菌株N-I对硝酸盐的降解符合一级反应动力学方程，反应的半衰期t_1/2为1.42 h，反应速率常数为0.488 h^-1。最佳反应pH=7，最佳反应温度为30℃，最佳NaHCO₃浓度为大于或等于2.5 g/L。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.