Removal of cationic dyes from aqueous solutions using microspherical particles of fly ash

Batch sorption experiments were carried out for the removal of cationic dyes (methylene blue and malachite green) from their aqueous solutions using sorbent made from fly ash-a waste material. Effects of various experimental parameters: initial dye concentration, contact time, pH, adsorbent dosage, solution temperature, surfactant addition and ionic strength on the fly ash sorption of dyes were evaluated. The isothermal data for sorption followed the Langmuir model. The maximum sorption capacity obtained for methylene blue and malachite green was 36.05 mg/g and 40.65 mg/g, respectively. Kinetic studies indicate that sorption on fly ash follows the pseudo-second order kinetics. Present research suggests that fly ash could be an appropriate adsorbent for the removal of basic dyes from aqueous solutions.     

Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system

In this study, advanced oxidation process utilizing Fenton's reaction was investigated for the decolorization and degradation of two commercial dyes viz., Red M5B, Blue MR and H-acid, a dye intermediate used in chemical industries for the synthesis of direct, reactive and azo dyes. Effect of Fe2 +, H2O2, pH, and contact time on the degradation of the dyes was studied. Maximum color and COD removal was obtained for Red MSB, H-acid and Blue MR at 10-25 mg/l of Fe2+ dose and 400-500 mg/l of H2O2 dose at pH 3.0. The initial oxidation reaction was found to fit into first order rate kinetics and the rate of oxidation of H-acid was higher than the other dyes. Release of chloride and sulfate from the Fenton's treated Red M5B dye and sulfate from H-acid and Blue MR indicates that the dye degradation proceeds through cleavage of the substituent group.     

褐煤对废水中酸性红B的吸附去除

选用褐煤作为廉价吸附剂,脱除模拟废水中染料酸性红B。研究了褐煤对废水中酸性红B的吸附动力学、等温吸附模式,考察了pH、褐煤投加量以及离子强度(NaCl)对吸附效果的影响。结果表明,吸附动力学较好地符合准二级速率方程(R2=1.000),并且以化学吸附为主;吸附等温式满足Langmuir方程(R2=0.986),最大单分子层吸附量为42 mg/g;废水中染料的去除率随溶液pH的减小而明显增加,在pH=1时,去除效果最好,证实吸附过程存在静电吸引及化学键合;在一定条件下,溶液中酸性红B的去除率随褐煤投加量增加而增加;吸附效果随溶液中离子强度(NaCl)的增加而增强。说明褐煤可以作为一种廉价吸附材料,用于处理含染料废水。     

Biomass-derived materials in the remediation of heavy-metal contaminated water: removal of Cadmium(II) and copper(II) from aqueous solutions

Manganese-coated activated carbon (MCAC) and activated carbon were used in batch experiments for the removal of cadmium(II) and copper(II). Results showed that uptake of Cd(II) and Cu(II) was unaffected by increases in pH (3.0 to 8.5) or concentration (1 to 20 mg/L). Increased ionic strength (from 0.001 to 1 M NaNO3), however, significantly affected the uptake of Cd(II); adsorption of Cu(II) was not affected. Freundlich adsorption isotherm results indicated that MCAC possessed higher sorption capacity than activated carbon. Second-order rate constants were found to be 0.0386 for activated carbon and 0.0633 g/mg x min for MCAC for Cd(II) and 0.0774 for AC and 0.1223 g/mg x min for MCAC for Cu(II). Column experiments showed that maximum sorption capacity of MCAC was 39.48 mg/g for Cu(II) and 12.21 mg/g for Cd(II).     

Sorption of basic and acid dyes from aqueous solutions onto oxihumolite

Naturally occurring kind of weathered and oxidised young brown coal called oxihumolite was used for an adsorptive removal of basic (Methylene Blue, Malachite Green) as well as acid (Egacid Orange, Midlon Black) dyes from waters. It was shown that both kinds of dyes can be sorbed onto oxihumolite. The maximum sorption capacities determined from the parameters of Langmuir isotherms ranged from 0.070 mmol g-1 (for Midlon Black) to 0.278 mmol g-1 (for Malachite Green) and did not differ significantly for basic and acid dyes. The dye sorption (except of Midlon Black) increased in the presence of inorganic salt. Non-ionic surfactants, and surfactants bearing the same charge as the dye exhibited only a minor effect on the dye sorption, whereas oppositely charged surfactants enhanced the dye sorption to a certain extent. The pH value of the aqueous phase exhibited rather pronounced effect on the sorption of acid dyes causing a suppression of the sorption with increasing pH. The sorption of basic dyes, on the other hand, remained almost unchanged in the examined pH range. Oxihumolite is recommended for the treatment of acid wastewaters because of its limited stability in alkaline aqueous solutions.     

A comparative study on the biosorption characteristics of some yeasts for Remazol Blue reactive dye

Biosorption capacities and rates of different kinds of dried yeasts (Saccharomyces cerevisiae, Schizosaccharomyces pombe, Kluyveromyces marxianus, Candida sp., C. tropicalis, C. lipolytica, C. utilis, C. quilliermendii and C. membranaefaciens) for Remazol Blue reactive dye from aqueous solutions were compared under laboratory conditions as a function of initial pH and initial dye concentration. Optimum initial biosorption pH was determined as 2 for all the yeasts. All the yeast species showed comparable and very high dye sorption at 100 mg/l initial dye concentration. The equilibrium sorption capacity of the biomass increased with increasing initial dye concentration up to 400 mg/l for Candida sp. C. lipolytica and C. tropicalis; up to 300 mg/l for C. quilliermendii and C. utilis and up to 200 mg/l for S. cerevisiae, S. pombe, K. marxianus and C. membranaefaciens while the adsorption yield of dye showed the opposite trend for all the yeasts. Among the nine yeast species, C. lipolytica exhibited the highest dye uptake capacity (Q(0) = 250 mg/g). Both the Freundlich and Langmuir adsorption models were found suitable for describing the biosorption of the dye by all the Candida yeasts (except C. membranaefaciens). The results indicated that the dye uptake process followed the pseudo-second-order kinetics for each dye-yeast system.     

Sorption of Zn(II) in aqueous solutions by scoria

We conducted kinetic and equilibrium sorption experiments on removal of Zn(II) from aqueous solutions by scoria (a vesicular pyroclastic rock with basaltic composition) from Jeju Island, Korea, in order to examine its potential use as an efficient sorbent. The batch-type kinetic sorption tests under variable conditions indicated that the percentage of Zn(II) removal by scoria increases with decreasing initial Zn(II) concentration, particle size, and sorbate/sorbent ratio. However, the sorption capacity decreases with the decrease of the initial Zn(II) concentration and sorbate/sorbent ratio. Equilibrium sorption tests show that Jeju scoria has a larger capacity and affinity for Zn(II) sorption than commercial powdered activated carbon (PAC); at initial Zn(II) concentrations of more than 10mM, the sorption capacity of Jeju scoria is about 1.5 times higher than that of PAC. The acquired sorption data are better fitted to the Langmuir isotherm than the Freundlich isotherm. Careful examination of ionic concentrations in sorption batches suggests that the sorption behavior is mainly controlled by cation exchange and typically displays characteristics of 'cation sorption'. The Zn(II) removal capacity decreases when solution pH decreases because of the competition with hydrogen ions for sorption sites, while the Zn(II) removal capacity increases under higher pH conditions, likely due to hydroxide precipitation. At an initial Zn(II) concentration of 5.0mM, the removal increases from 70% to 96% with the increase of initial pH from 3.0 to 7.0. We recommend Jeju scoria as an economic and efficient sorbent for Zn(II) in contaminated water.     

Potential of immobilized bitter gourd (Momordica charantia) peroxidases in the decolorization and removal of textile dyes from polluted wastewater and dyeing effluent

Immobilized peroxidases from Momordica charantia were highly effective in decolorizing reactive textile dyes compared to its soluble counterpart. Dye solutions, 50-200 mg/l, were treated with soluble and immobilized bitter gourd peroxidases (specific activity of 99.0 EU per mg protein). The decolorization of dyes with soluble and immobilized enzyme was maximum in the range of pH 3.0-4.0. The effect of different temperatures on the dye decolorization was monitored and it was observed that all the dyes were maximally decolorized at 40 degrees C. In order to examine the operational stability of the immobilized preparation, the enzyme was repeatedly exploited for the decolorization of the dyes from fresh batch of dye solutions. Even after 10 cycles in each case the immobilized preparation retained nearly 50% of the initial enzyme activity. The immobilized enzyme exhibited more than 90% of the original activity while the soluble enzyme lost 33% of the initial activity when stored for 40 d at room temperature. Mixtures of three, four and eight dyes were prepared and treated with soluble and immobilized bitter gourd peroxidase. Each mixture was decolorized by more than 80% when treated with immobilized enzyme. Dyeing effluent collected from local dyers was treated with both types of enzyme preparations. Immobilized enzyme was capable of removing remarkably high concentration of color from the effluent. TOC content of soluble and immobilized enzyme treated individual dyes, mixture of dyes and dyeing effluent was determined and it was observed that higher TOC was removed after treatment with immobilized enzyme.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Removal of aqueous nickel (II) using laterite as a low-cost adsorbent.

The present paper describes the laboratory study of laterite as a low-cost adsorbent for removal of aqueous nickel (II). At pH 7 and a temperature of 30 degrees C, a sorbent dose of 15 mg/L resulted in approximately 90% removal of nickel (II) from its initial concentration of 10 mg/L. A maximum removal of 98% of the adsorbate was observed with an adsorbent particle size of 210 micro with the above conditions. Batch kinetics results were described by fitting in a Langmuir isotherm. Helffrich's half-time equation (Helffrich, 1962) has been applied to evaluate the adsorption process. It appears that film diffusion would be the rate-limiting step. The effect of pH on the sorption process was carried out to a value of 8.0. The removal rate of nickel was found to be the function of pH of the reaction mixture. The rate of nickel uptake by laterite with the decrease in pH value has been explained on the basis of aqueous-complex formation and the subsequent acid-base dissociation at the solid-solution interface.     

Treatment of Basic Red 29 dye solution using iron-aluminum electrode pairs by electrocoagulation and electro-Fenton methods

The aim of this study is the treatment of Basic Red 29 (BR29) dye solution using hybrid iron-aluminum electrodes by electrocoagulation and electro-Fenton methods. The effect of current density, initial pH, supporting electrolyte, H₂O₂, and initial dye concentration on dye removal efficiency was investigated, and the best experimental conditions were obtained. Time-coarse variation of UV-Vis spectra and toxicity and chemical oxygen demand (COD) removal were also examined at the best experimental conditions. Both systems were found very successful for the removal of BR29 dye. The removal efficiency of >95 % for BR29 dye solution was reached easily in a short time. At the best experimental conditions, for the initial BR29 concentration of 100 mg/L, >95 % BR29 dye and 71.43 % COD removal were obtained after 20 and 40 min of electrolysis, respectively. Additionally, toxicity results for electro-Fenton treatment of 100 mg/L BR29 were also very promising. According to the results obtained, although electro-Fenton is more effective, both systems can be used successfully to treat textile wastewater including dyes.     

Decolorization of mono-azo dyes in wastewater by advanced oxidation process: A case study of acid red 1 and acid yellow 23

Advanced Oxidation Processes (AOPs) have been used as emerging wastewater treatment technologies which can effectively handle various hazardous organics in wastewater and groundwater. The photooxidation of two non-biodegradable azo dyes, acid red 1 and acid yellow 23, were studied in an UV/hydrogen peroxide photochemical reactor with a 5 kW low pressure mercury lamp. It was observed that the decomposition of both azo dyes were pseudo-first order reactions with respect to the azo dye concentrations. Simultaneously, the effects of hydrogen peroxide dosage, pH, initial concentration of the azo dyes and intensity of UV light were also studied. Moreover, the time required for the 50% removal of azo dyes and observed pseudo-first order rate constants were used as parameters to show the efficiency of azo dye treatment.     

铈离子光催化降解茜素绿的性能和机理

主要研究了简单铈离子（Ce3＋）在紫外光（uv）的作用下对蒽醌染料茜素绿（AG）的光催化降解效果和反应机理。结果表明，UV／Ce3＋体系能够有效降解AG，初始反应速率随AG浓度的倒数值和Ce3＋浓度的增加而线性增加，随初始溶液pH的增加先降低后增加，在酸性条件下有很高的TOC去除率。荧光探针实验表明，反应过程中可以产生·OH自由基。UV／Ce3＋体系对其他类型染料和对硝基苯酚都有较好的降解效果。     

载钴活性焦对As(V)的吸附性能与去除效果

使用沉淀负载法制备了载钴活性焦,并研究了溶液pH值、反应时间、As(V)初始浓度以及共存阴离子等对载钴活性焦吸附去除水环境中As(V)的影响。结果表明,(1)载钴后活性焦的比表面积和孔容积分别提高了20.87%和43.47%;(2)载钴活性焦对As(V)最佳吸附pH值为4.0,当As(V)的初始浓度为10 mg/L时,As(V)去除率可达97%;(3)吸附过程符合准二级动力学模型(k2=0.66,R2=0.96),吸附等温线为Freundlich型(kF=8.227,1/n=0.396,R2=0.97);(4)稳定性实验验证了载钴活性焦的稳定性,钴不易脱附,最大脱附率仅为0.145%。     

新生态MnO2吸附剂对酸性媒介染料废水脱色特性研究

本文主要报道了一种用于染料废水处理的新型材料即新生态MnO2 及其对三种酸性媒介染料染色废水的脱色作用及影响脱色效果的主要因素。研究结果表明 ,新生态MnO2 对酸性媒介染料的吸附能力很强 ,当染料浓度为2 0 0mg/L、pH <2时 ,其对酸性媒介黑T、酸性媒介绿G和酸性媒介黄GG的脱色率分别达 98.2 %、94.5 %和 96 .4%。染料吸附效果受体系pH值、MnO2 投加量、吸附时间及温度等因素的影响 ,其中pH值是最主要的影响因素。新生态MnO2 对酸性媒介黄GG的吸附作用符合Langmuir吸附等温式     

Degradation of azo dyes using low iron concentration of Fenton and Fenton-like system

This study investigated Fenton and Fenton-like reactions at low iron concentration (相似文献   

Equilibrium and kinetic modelling of chromium(III) sorption by animal bones

The paper discusses sorption of Cr(III) ions from aqueous solutions by animal bones. Animal bones were found to be an efficient sorbent with the maximum experimentally determined sorption capacity in the range 29-194 mg g(-1) that depended on pH and temperature. The maximum experimentally determined sorption capacity was obtained at 50 degrees C, pH 5. Batch kinetics and equilibrium experiments were performed in order to investigate the influence of contact time, initial concentration of sorbate and sorbent, temperature and pH. It was found that sorption capacity increased with increase of Cr(III) concentration, temperature and initial pH of metal solution. Mathematical models describing kinetics and statics of sorption were proposed. It was found that process kinetics followed the pseudo-second-order pattern. The influence of sorbent concentration was described with Langmuir-type equation and the influence of sorbate concentration was described with empirical dependence. The models were positively verified.     

Treatment of textile dyeing wastewater by biomass of Lactobacillus: Lactobacillus 12 and Lactobacillus rhamnosus

The main purpose of this study was to investigate the effectiveness of Lactobacillus 12 and Lactobacillus rhamnosus as both cells and biomasses for the removal of dye from real textile dyeing wastewater. The removal experiments were conducted according to the Box–Behnken experimental design, and the regression equations for the removal of dye were determined by the Minitab 14 program. The optimum variables were found to be 10 g/?L biomass concentration for biomasses, 3 for initial pH of the solution, and 20 °C for temperature with an observed dye removal efficiency of about 60 and 80 % with L. 12 and L. rhamnosus biomasses, respectively. Scanning electron microscopy and Fourier transform infrared spectroscopy images also showed that the biomass characteristics studied were favored by the sorption of the dye from the textile industry wastewater. Consequently, these biomasses may be considered as good biosorbents due to their effective yields and the lower cost of the removal of dyes from the effluents of the textile dyeing house.     

铈离子光催化降解茜素绿的性能和机理简

主要研究了简单铈离子（Ce³⁺）在紫外光（UV）的作用下对蒽醌染料茜素绿（AG）的光催化降解效果和反应机理。结果表明，UV/Ce³⁺体系能够有效降解AG，初始反应速率随AG浓度的倒数值和Ce³⁺浓度的增加而线性增加，随初始溶液pH的增加先降低后增加，在酸性条件下有很高的TOC去除率。荧光探针实验表明，反应过程中可以产生·OH自由基。UV/Ce³⁺体系对其他类型染料和对硝基苯酚都有较好的降解效果。     

超声-Fenton高级氧化降解染料工业废水的研究

采用超声与Fenton高级氧化技术联合处理染料废水,取得了满意的效果。同时考察了初始浓度、初始pH值、超声时间、超声频率、超声功率、H2O2和FeSO4初始浓度等因素对其COD去除效果的影响,当超声波频率为45 kHz,功率为200 W,初始pH值为2.63,超声时间为150 min,H2O2浓度为60 mmol/L,FeSO4浓度为12 mmol/L时,染料废水COD去除率达到91.8%。