Comparison of an assay for Dehalococcoides DNA and a microcosm study in predicting reductive dechlorination of chlorinated ethenes in the field

The study aims to compare the detection of 16S rRNA gene of Dehalococcoides species and the microcosm study for biotransformation in predicting reductive dechlorination of chlorinated ethenes in ground water at hazardous waste sites. A total of 72 ground water samples were collected from 12 PCE or TCE contaminated sites in the United States. The samples were analyzed and used to construct microcosms in the laboratory. The results showed that the presence of Dehalococcoides DNA was well associated with dechlorination to ethene in the field. Nearly half of the wells where Dehalococcoides DNA was detected had ethene as a dechlorination end product. In comparison, for ground water samples of 16 wells where ethene was detected, ethene was produced in 11 of the corresponding microcosms. For most microcosms, during two years of incubation, dechlorination was less extensive than that observed in the field.     

Anaerobic biodegradation of alkylbenzenes and trichloroethylene in aquifer sediment down gradient of a sanitary landfill

The objective of this investigation was to evaluate the anaerobic biodegradability of benzene, toluene, ethylbenzene, ortho-, meta- and para-xylene (BTEX) and trichloroethylene (TCE) in aquifer sediment down gradient of an unlined landfill. The major organic contaminants identified in the shallow unconfined aquifer are cis-dichloroethylene (c-DCE) and toluene. The biodegradative potential of the contaminated aquifer was measured in three sets of microcosms constructed using anaerobic aquifer sediment from three boreholes down gradient of the landfill. The degradability of BTEX and TCE was examined under ambient and amended conditions. TCE was degraded in microcosms with aquifer material from all three boreholes. Toluene biodegradation was inconsistent, exhibiting biodegradation with no lag in one set of microcosms but more limited biodegradation in two additional sets of microcosms. TCE exhibited an inhibitory effect on toluene degradation at one location. The addition of calcium carbonate stimulated TCE biodegradation which was not further stimulated by nutrient addition. TCE was converted to ethylene, a harmless byproduct, in all tests. Benzene, ethylbenzene and xylene isomers were recalcitrant in both ambient and amendment experiments. Biodegradation occurred under methanogenic conditions as methane was produced in all experiments. Bromoethane sulfonic acid (BES), a methanogenic inhibitor, inhibited methane and ethylene production and TCE biodegradation. The results indicate the potential for intrinsic bioremediation of TCE and toluene down gradient of the Wilder's Grove, North Carolina, landfill. The low concentrations of TCE in monitoring wells was consistent with its biodegradation in laboratory microcosms.     

The need for bioaugmentation after thermal treatment of a TCE-contaminated aquifer: Laboratory experiments

A microcosm study was conducted to evaluate the need for bioaugmentation after a thermal treatment to anaerobically dechlorinate trichloroethene (TCE) to ethene. The microcosms were either: heated to 100 degrees C and slowly cooled to simulate thermal remediation while bioaugmenting when the declining temperature reached 10 degrees C; or kept at ambient groundwater temperatures (10 degrees C) and bioaugmented for comparison. Aquifer samples from three sediment locations within a TCE-polluted source zone were investigated in duplicate microcosms. In biostimulated (5 mM lactate) and heated microcosms, no conversion of TCE was observed in 4 out of 6 microcosms, and in the remaining microcosms the dechlorination of TCE was incomplete to cDCE (cis-dichloroethene). By comparison, complete TCE dechlorination to ethene was observed in 4 out of 6 heated microcosms that were bioaugmented with a highly enriched dechlorinating mixed culture, KB-1, but no electron donor, and also in 4 of 6 microcosms that were augmented with KB-1 and an electron donor (5 mM lactate). These data suggest that electron donor released during heating, was capable of promoting complete dechlorination coincident with bioaugmentation. Heated microcosms demonstrated less methanogenesis than unheated microcosms, even with elevated H2 concentrations and addition of KB-1, which contains methanogens. This suggests that the heating process suppressed the native microbial community, which can decrease competition with the bioaugmented culture and increase the effectiveness of dechlorination following a thermal treatment. Specifically, cDCE removal rates were four to six times higher in heated than unheated bioaugmented microcosms. This study confirms the need for bioaugmentation following a laboratory thermal treatment to obtain complete dechlorination of TCE.     

Quantification of biotransformation of chlorinated hydrocarbons in a biostimulation study: added value via stable carbon isotope analysis

Stable carbon isotope analysis of chlorinated aliphatic compounds was performed at an in situ biostimulation pilot test area (PTA) at a site where 1,2-dichloroethane (1,2-DCA) and trichloroethene (TCE) were present in groundwater. Chlorinated products of TCE reductive dechlorination (cis-dichloroethene (cDCE) and vinyl chloride (VC)) were present at concentrations of 17.5 to 126.4 micromol/L. Ethene, a potential degradation product of both 1,2-DCA dihaloelimination and TCE reductive dechlorination was also present in the PTA. Emulsified soybean oil and lactate were added as electron donors to stimulate anaerobic dechlorination in the PTA. Stable carbon isotope analysis provided evidence that dechlorination was occurring in the PTA during biostimulation, and a means of monitoring changes in dechlorination efficiency over the 183 day monitoring period. Stable carbon isotope analysis was also used to determine if ethene production in the PTA was due to dechlorination of TCE, 1,2-DCA, or both. Fractionation factors (alpha) were determined in the laboratory during anaerobic biotransformation of 1,2-DCA via a dihaloelimination reaction in four separate enrichment cultures. These alpha values (as well as the previously published ranges of alpha for the dechlorination of TCE, cDCE and 1,2-DCA) were used, along with isotopic values measured during the pilot test, to derive quantitative estimates of biotransformation during the pilot test. Dechlorination was found to account for 10.7 to 35.9%, 21.9 to 74.9%, and 54.4 to 67.8% of 1,2-DCA, TCE and cDCE concentration loss respectively in the PTA. Stable carbon isotope analysis indicates that dechlorination of 1,2-DCA, TCE and cDCE were all significant processes during the pilot test, while ethene production during the pilot test was dominated by 1,2-DCA dihaloelimination. This study demonstrates how stable carbon isotope analysis can provide more conservative estimates of the extent of biotransformation than do conventional protocols. In addition, in a complex mixed plume such as this, compound specific isotope analysis is shown to be one of the few methods available for clarifying dominant biotransformation pathways where breakdown products are non-exclusive (i.e. ethene).     

Attenuation reactions in a multiple contaminated aquifer in Bitterfeld (Germany)

Large-scale contaminated sites with multiple contaminants in the groundwater present a challenge to risk assessment and remediation. Attenuation reactions take place in the subsurface and act to contain contaminants, but must be thoroughly investigated on a site-specific basis. Field data from monitoring wells at a contaminated industrial site in Bitterfeld, Germany, are presented and analyzed for evidence of the prevalent biodegradation reactions. The groundwater in the Tertiary aquifer is contaminated with large quantities of chlorinated aliphatic compounds, in addition to chlorobenzenes and BTEX. In this strictly anaerobic environment, geochemical indications for several microbial processes were found, including methanogenesis, sulfate and iron reduction as well as reductive dechlorination of the chlorinated hydrocarbons. Direct evidence for the latter degradation reaction was observed along the flowpath due to the appearance of intermediates and an increase in the degree of dechlorination.     

Mechanisms of electron acceptor utilization: implications for simulating anaerobic biodegradation

Simulation of biodegradation reactions within a reactive transport framework requires information on mechanisms of terminal electron acceptor processes (TEAPs). In initial modeling efforts, TEAPs were approximated as occurring sequentially, with the highest energy-yielding electron acceptors (e.g. oxygen) consumed before those that yield less energy (e.g., sulfate). Within this framework in a steady state plume, sequential electron acceptor utilization would theoretically produce methane at an organic-rich source and Fe(II) further downgradient, resulting in a limited zone of Fe(II) and methane overlap. However, contaminant plumes often display much more extensive zones of overlapping Fe(II) and methane. The extensive overlap could be caused by several abiotic and biotic processes including vertical mixing of byproducts in long-screened monitoring wells, adsorption of Fe(II) onto aquifer solids, or microscale heterogeneity in Fe(III) concentrations. Alternatively, the overlap could be due to simultaneous utilization of terminal electron acceptors. Because biodegradation rates are controlled by TEAPs, evaluating the mechanisms of electron acceptor utilization is critical for improving prediction of contaminant mass losses due to biodegradation. Using BioRedox-MT3DMS, a three-dimensional, multi-species reactive transport code, we simulated the current configurations of a BTEX plume and TEAP zones at a petroleum-contaminated field site in Wisconsin. Simulation results suggest that BTEX mass loss due to biodegradation is greatest under oxygen-reducing conditions, with smaller but similar contributions to mass loss from biodegradation under Fe(III)-reducing, sulfate-reducing, and methanogenic conditions. Results of sensitivity calculations document that BTEX losses due to biodegradation are most sensitive to the age of the plume, while the shape of the BTEX plume is most sensitive to effective porosity and rate constants for biodegradation under Fe(III)-reducing and methanogenic conditions. Using this transport model, we had limited success in simulating overlap of redox products using reasonable ranges of parameters within a strictly sequential electron acceptor utilization framework. Simulation results indicate that overlap of redox products cannot be accurately simulated using the constructed model, suggesting either that Fe(III) reduction and methanogenesis are occurring simultaneously in the source area, or that heterogeneities in Fe(III) concentration and/or mineral type cause the observed overlap. Additional field, experimental, and modeling studies will be needed to address these questions.     

Assessing chlorinated ethene degradation in a large scale contaminant plume by dual carbon-chlorine isotope analysis and quantitative PCR

The fate of chlorinated ethenes in a large contaminant plume originating from a tetrachloroethene (PCE) source in a sandy aquifer in Denmark was investigated using novel methods including compound-specific carbon and chlorine isotope analysis and quantitative real-time polymerase chain reaction (qPCR) methods targeting Dehaloccocoides sp. and vcrA genes. Redox conditions were characterized as well based on concentrations of dissolved redox sensitive compounds and sulfur isotopes in SO(4)(2-). In the first 400 m downgradient of the source, the plume was confined to the upper 20 m of the aquifer. Further downgradient it widened in vertical direction due to diverging groundwater flow reaching a depth of up to 50 m. As the plume dipped downward and moved away from the source, O(2) and NO(3)(-) decreased to below detection levels, while dissolved Fe(2+) and SO(4)(2-) increased above detectable concentrations, likely due to pyrite oxidation as confirmed by the depleted sulfur isotope signature of SO(4)(2-). In the same zone, PCE and trichloroethene (TCE) disappeared and cis-1,2-dichloroethene (cDCE) became the dominant chlorinated ethene. PCE and TCE were likely transformed by reductive dechlorination rather than abiotic reduction by pyrite as indicated by the formation of cDCE and stable carbon isotope data. TCE and cDCE showed carbon isotope trends typical for reductive dechlorination with an initial depletion of (13)C in the daughter products followed by an enrichment of (13)C as degradation proceeded. At 1000 m downgradient of the source, cDCE was the dominant chlorinated ethene and had reached the source δ(13)C value confirming that cDCE was not affected by abiotic or biotic degradation. Further downgradient (up to 1900 m), cDCE became enriched in (13)C by up to 8 ‰ demonstrating its further transformation while vinylchloride (VC) concentrations remained low (<1 μg/L) and ethene was not observed. The correlated shift of carbon and chlorine isotope ratios of cDCE by 8 and 3.9 ‰, respectively, the detection of Dehaloccocides sp genes, and strongly reducing conditions in this zone provide strong evidence for reductive dechlorination of cDCE. The significant enrichment of (13)C in VC indicates that VC was transformed further, although the mechanism could not be determined. The transformation of cDCE was the rate limiting step as no accumulation of VC occurred. In summary, the study demonstrates that carbon-chlorine isotope analysis and qPCR combined with traditional approaches can be used to gain detailed insight into the processes that control the fate of chlorinated ethenes in large scale plumes.     

Evaluation of TCDD biodegradability under different redox conditions

Polychlorinated dibenzo-p-dioxins have been generated as unwanted by-products in many industrial processes. Although their widespread distribution in different environmental compartments has been recognized, little is known about their fate in the ultimate environment sinks. The highly stable dioxin isomer 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) has been called the most toxic compound known to man. In this laboratory microcosm study, TCDD bioavailability was evaluated under five reduction/oxidation (redox) conditions including aerobic biodegradation, aerobic cometabolism, methanogenesis, iron reduction, and reductive dechlorination. Activated sludge and aquifer sediments from a TCDD and a pentachlorophenol (PCP) contaminated site were used as the inocula. Acetate, sludge cake, and cane molasses were used as the primary substrates (carbon sources) in cometabolism and reductive dechlorination microcosms. After a 90-day incubation period, microcosms constructed under reductive dechlorination conditions were the only treatment showing promising remediation results. The highest TCDD degradation rate [up to 86% of TCDD removal (with an initial concentration of 96 microg/kg of soil)] was observed in the microcosms with anaerobic activated sludge as the microbial inocula and sludge cakes as the primary substrates. Except for reductive dechlorination microcosms, no significant TCDD removal was observed in the microcosms prepared under other conditions. Thus, application of an effective primary substrate to enhance the reductive dechlorination process is a feasible method for TCDD bioremediation. Bioremediation expense can be significantly reduced by the supplement of some less expensive alternative substrates (e.g., sludge cakes, cane molasses). Results would be useful in designing a scale-up in situ or on-site bioremediation system such as bioslurry reactor for field application.     

Use of statistical tools to evaluate the reductive dechlorination of high levels of TCE in microcosm studies

A large, multi-laboratory microcosm study was performed to select amendments for supporting reductive dechlorination of high levels of trichloroethylene (TCE) found at an industrial site in the United Kingdom (UK) containing dense non-aqueous phase liquid (DNAPL) TCE. The study was designed as a fractional factorial experiment involving 177 bottles distributed between four industrial laboratories and was used to assess the impact of six electron donors, bioaugmentation, addition of supplemental nutrients, and two TCE levels (0.57 and 1.90 mM or 75 and 250 mg/L in the aqueous phase) on TCE dechlorination. Performance was assessed based on the concentration changes of TCE and reductive dechlorination degradation products. The chemical data was evaluated using analysis of variance (ANOVA) and survival analysis techniques to determine both main effects and important interactions for all the experimental variables during the 203-day study. The statistically based design and analysis provided powerful tools that aided decision-making for field application of this technology. The analysis showed that emulsified vegetable oil (EVO), lactate, and methanol were the most effective electron donors, promoting rapid and complete dechlorination of TCE to ethene. Bioaugmentation and nutrient addition also had a statistically significant positive impact on TCE dechlorination. In addition, the microbial community was measured using phospholipid fatty acid analysis (PLFA) for quantification of total biomass and characterization of the community structure and quantitative polymerase chain reaction (qPCR) for enumeration of Dehalococcoides organisms (Dhc) and the vinyl chloride reductase (vcrA) gene. The highest increase in levels of total biomass and Dhc was observed in the EVO microcosms, which correlated well with the dechlorination results.     

Monitoring trichloroethene remediation at an iron permeable reactive barrier using stable carbon isotopic analysis

Stable carbon isotopic analysis, in combination with compositional analysis, was used to evaluate the performance of an iron permeable reactive barrier (PRB) for the remediation of ground water contaminated with trichloroethene (TCE) at Spill Site 7 (SS7), F.E. Warren Air Force Base, Wyoming. Compositional data indicated that although the PRB appeared to be reducing TCE to concentrations below treatment goals within and immediately downgradient of the PRB, concentrations remained higher than expected at wells further downgradient (i.e. >9 m) of the PRB. At two wells downgradient of the PRB, TCE concentrations were comparable to upgradient values, and delta13C values of TCE at these wells were not significantly different than upgradient values. Since the process of sorption/desorption does not significantly fractionate carbon isotope values, this suggests that the TCE observed at these wells is desorbing from local aquifer materials and was present before the PRB was installed. In contrast, three other downgradient wells show significantly more enriched delta13C values compared to the upgradient mean. In addition, delta13C values for the degradation products of TCE, cis-dichloroethene and vinyl chloride, show fractionation patterns expected for the products of the reductive dechlorination of TCE. Since concentrations of both TCE and degradation products drop to below detection limit in wells within the PRB and directly below it, these downgradient chlorinated hydrocarbon concentrations are attributed to desorption from local aquifer material. The carbon isotope values indicate that this dissolved contaminant is subject to local degradation, likely due to in situ microbial activity.     

Dechlorination after thermal treatment of a TCE-contaminated aquifer: laboratory experiments

A microcosm study was conducted to evaluate dechlorination of trichloroethene (TCE) to ethene and survival of dechlorinating bacteria after a thermal treatment in order to explore the potential for post-thermal bioremediation. Unamended microcosms containing groundwater and aquifer material from a contaminated site dechlorinated TCE to cis-1,2-dichloroethene (cDCE), while lactate-amended microcosms dechlorinated TCE to cDCE or ethene. A thermal treatment was simulated by heating a sub-set of microcosms to 100 degrees C for 10d followed by cooling to 10 degrees C over 150 d. The heated microcosms demonstrated no dechlorination when unamended. However, when amended with lactate, cDCE was produced in 2 out of 6 microcosms within 300 d after heating. Dechlorination of TCE to cDCE thus occurred in fewer heated (2 out of 12) than unheated (10 out of 12) microcosms. In unheated microcosms, the presence of dechlorinating microorganisms, including Dehalococcoides, was confirmed using nested PCR of 16S rRNA genes. Dechlorinating microorganisms were detected in fewer microcosms after heating, and Dehalococcoides were not detected in any microcosms after heating. Dechlorination may therefore be limited after a thermal treatment in areas that have been heated to 100 degrees C. Thus, inflow of groundwater containing dechlorinating microorganisms and/or bioaugmention may be needed for anaerobic dechlorination to occur after a thermal treatment.     

Natural attenuation of trichloroethylene in fractured shale bedrock

This paper describes one of the first well-documented field examples of natural attenuation of trichloroethylene (TCE) in groundwater in a fractured shale bedrock. The study was carried out adjacent to a former waste burial site in Waste Area Grouping 5 (WAG5) on the Oak Ridge Reservation, Oak Ridge, TN. A contaminant plume containing TCE and its daughter products were detected downgradient from the buried waste pits, with most of the contamination occurring in the upper 6 m of the bedrock. The monitoring well array consists of a 35-m-long transect of multilevel sampling wells, situated along a line between the waste pits and a seep which discharges into a small stream. Concentrations of volatile organic carbons (VOCs) were highest in the waste trenches and decreased with distance downgradient towards the seep. Sampling wells indicated the presence of overlapping plumes of TCE, cis-dichloroethylene (cDCE), vinyl chloride (VC), ethylene, ethane, and methane, with the daughter products extending further downgradient than the parent (TCE). This type of distribution suggests anaerobic biodegradation. Measurements of redox potential at the site indicated that iron-reduction, sulfate reduction, and potentially methanogensis were occurring and are conducive to dechlorination of TCE. Bacteria enrichment of groundwater samples revealed the presence of methanotrophs, methanogens, iron-reducing bacteria and sulfate-reducing bacteria, all of which have previously been implicated in anaerobic biodegradation of TCE. 16S rDNA sequence from DNA extracted from two wells were similar to sequences of organisms previously implicated in the anaerobic biodegradation of chlorinated solvents. The combined data strongly suggest that anaerobic biodegradation of the highly chlorinated compounds is occurring. Aerobic biodegradation may also be occurring in oxygenated zones, including near a seep where groundwater exits the site, or in the upper bedrock during seasonal fluctuations in water table elevation and oxygen levels.     

Factors controlling BTEX and chlorinated solvents plume length under natural attenuation conditions

Natural attenuation is presently used at numerous sites where groundwater is contaminated. In order to simulate this attenuation, reactive transport models are often used but they are quite complex and depend on both physical and chemical conditions in the aquifer. As complex numerical models cannot be used to study all possible cases, we develop here analytical solutions to draw general conclusions. Our strategy, called MIKSS (Mixed Instantaneous and Kinetics Superposition Sequence), allows the calculation of the concentrations of all reacting substances in a plume. It is an extension of the superimposition principle that is able to treat the case of joint kinetics and instantaneous reactions. The basic equations have been extended to treat different reactions that occur in the plume core and at its fringe. At first we consider one organic substance degraded under all oxidising conditions (toluene for instance). For this problem the size of the plume depends on the reduced source width and on the ratio of the organic substance concentration to the sum of the electron acceptors' concentrations. For several BTEX substances having different degradation behaviour the formulation is similar, but leads to quite different plume lengths for each substance. Contrary to the case of one substance, the plumes can be quite long and may not satisfy the target risk level. For chlorinated solvents we developed a specific approach to take under consideration all reactions and particularly the competition for hydrogen. A formula is given to assess the size of the plume core, i.e. the zone with highly reducing conditions. The factors influencing the core length are the same as for BTEX (source width, dispersivity, organic carbon content). The size of the TCE plume is calculated from the plume core length and the kinetic constant of TCE degradation. Using assumptions of degradation constants for DCE and VC it is also possible to calculate the longitudinal concentration profile of these substances. The degradation of moderately substituted solvents under oxic conditions reduces the size of their plumes but under these conditions TCE becomes the major threat. Among the conditions studied in this paper, very few chlorinated solvents sites can lead to a negligible risk at an acceptable distance from the source.     

Aerobic biodegradation of dichloroethenes by indigenous bacteria isolated from contaminated sites in Africa

The widespread use of tetrachloroethene (PCE) and trichloroethene (TCE) as dry cleaning solvents and degreasing agents for military and industrial applications has resulted in significant environmental contamination worldwide. Anaerobic biotransformation of PCE and TCE through reductive dechlorination frequently lead to the accumulation of dichloroethenes (DCEs), thus limiting the use of reductive dechlorination for the biotransformation of the compounds. In this study, seven bacteria indigenous to contaminated sites in Africa were characterized for DCE degradation under aerobic conditions. The specific growth rate constants of the bacterial isolates ranged between 0.346-0.552d(-1) and 0.461-0.667d(-1) in cis-DCE and trans-DCE, respectively. Gas chromatographic analysis revealed that up to 75% of the compounds were degraded within seven days with the degradation rate constants ranging between 0.167 and 0.198d(-1). The two compounds were also observed to be significantly degraded, simultaneously, rather than sequentially, when present as a mixture. Phylogenetic analysis of the 16S rRNA gene sequences of the bacterial isolates revealed their identity as well as their relation to other environmentally-important bacteria. The observed biodegradation of DCEs may contribute to PCE and TCE removal at the aerobic fringe of groundwater plumes undergoing reductive dechlorination in contaminated sites.     

Progression of natural attenuation processes at a crude-oil spill site: I. Geochemical evolution of the plume

A 16-year study of a hydrocarbon plume shows that the extent of contaminant migration and compound-specific behavior have changed as redox reactions, most notably iron reduction, have progressed over time. Concentration changes at a small scale, determined from analysis of pore-water samples drained from aquifer cores, are compared with concentration changes at the plume scale, determined from analysis of water samples from an observation well network. The small-scale data show clearly that the hydrocarbon plume is growing slowly as sediment iron oxides are depleted. Contaminants, such as ortho-xylene that appeared not to be moving downgradient from the oil on the basis of observation well data, are migrating in thin layers as the aquifer evolves to methanogenic conditions. However, the plume-scale observation well data show that the downgradient extent of the Fe2+ and BTEX plume did not change between 1992 and 1995. Instead, depletion of the unstable Fe (III) oxides near the subsurface crude-oil source has caused the maximum dissolved iron concentration zone within the plume to spread at a rate of approximately 3 m/year. The zone of maximum concentrations of benzene, toluene, ethylbenzene and xylene (BTEX) has also spread within the anoxic plume. In monitoring the remediation of hydrocarbon-contaminated ground water by natural attenuation, subtle concentration changes in observation well data from the anoxic zone may be diagnostic of depletion of the intrinsic electron-accepting capacity of the aquifer. Recognition of these subtle patterns may allow early prediction of growth of the hydrocarbon plume.     

In situ sequential treatment of a mixed contaminant plume

Groundwater plumes often contain a mixture of contaminants that cannot easily be remediated in situ using a single technology. The purpose of this research was to evaluate an in situ treatment sequence for the control of a mixed organic plume (chlorinated ethenes and petroleum hydrocarbons) within a Funnel-and-Gate. A shallow plume located in the unconfined aquifer at Alameda Point, CA, was found to contain up to 218,000 μg/l of cis-1,2 dichloroethene (cDCE), 16,000 μg/l of vinyl chloride (VC) and <1000 μg/l of 1,1 dichloroethene (1,1 DCE), trans-1,2 dichloroethene (trans-1,2 DCE) and trichloroethene (TCE). Total benzene, toluene, ethylbenzene and xylenes (BTEX) concentrations were <10,000 μg/l. Contaminated groundwater was funneled into a gate, 3.0 m wide, 4.5 m long and 6.0 m deep (keyed into the underlying aquitard) where treatment occurred. The initial gate segment consisted of granular iron, for the reductive dechlorination of the higher chlorinated ethenes. The second segment, the biosparge zone, promoted aerobic biodegradation of petroleum hydrocarbons and any remaining lesser-chlorinated compounds, stimulated by dissolved oxygen (DO) and carbon dioxide (CO₂) additions via an in situ sparge system (CO₂ was used to neutralize the high pH produced from reactions in the iron wall). Groundwater was drawn through the gate by pumping two wells located at the sealed, downgradient, end. Over a 4-month period an estimated 1350 g of cDCE flowed into the treatment gate and the iron wall removed 1230 g, or 91% of the mass. The influent mass of VC was 572 g and the iron wall removed 535 g, corresponding to 94% mass removal. The other chlorinated ethenes had significantly lower influent masses (3 to 108 g) and the iron wall removed the majority of the mass resulting in >96% mass removal for any of the compounds. In spite of these high removal percentages, laboratory column tests indicated that at these levels of chlorinated contaminants, surface saturation of the iron grains likely contributed to lower than expected reaction rates. In the biosparge zone, mass removal of cDCE appeared to occur predominantly by biodegradation (65%) with volatilization (35%) being an important secondary process. The dominant removal process for VC was volatilization (70%) although significant biodegradation was also indicated (30%). Laboratory microcosm results confirmed the potential for aerobic biodegradation of cDCE and VC. When average influent field concentrations for cDCE and VC were 220,000 and 46,000 μg/l, respectively, the sequential treatment unit removed 99.6% of the total mass and when the influent concentrations decreased to 26,000 and 19,000 μg/l for cDCE and VC, respectively, >99.9% removal within the treatment gate was attained. BTEX compounds were found to be significantly retarded in the iron treatment zone. Although they did eventually break through the granular iron, and into the gravel transition zone, none of these compounds was detected in the biosparge zone. No noticeable interferences between the anaerobic (reductive) and aerobic parts of the system occurred during testing. The results of this experiment show that in situ treatment sequences are viable, although further work is needed to optimize performance.     

Anaerobic biodegradation of weathered polychlorinated biphenyls (PCBs) in contaminated sediments of Porto Marghera (Venice Lagoon,Italy)

The biodegradation of weathered polychlorinated biphenyls (PCBs) (mono and di-chlorinated biphenyls along with PCBs partially ascribed to Aroclor 1242 and 1254) occurring at 1.5-2.5 mg/kg in three different sediments collected from the Porto Marghera contaminated area of Venice Lagoon (Italy) was reported in this study. Strictly anaerobic, slurry microcosms consisting of sediments suspended (at 25% v/v) in a marine salt medium, lagoon water or lagoon water supplemented with NaHCO3 and Na2S were developed and monitored for PCB transformation, sulfate consumption and methane (CH4) production for 6 months. A marked depletion of highly chlorinated biphenyls along with the accumulation of low-chlorinated, often ortho-substituted biphenyls was observed in the biologically active microcosms, where a remarkable consumption of sulfate and/or a significant production of CH4 were also detected. Notably, a more extensive PCB transformation was observed in the microcosms developed with site water (both without or with NaHCO3 plus Na2S), where both the initial concentration of sulfate and sulfate consumption were five fold-higher than in the corresponding microcosms with salt medium. These data indicate that weathered PCBs of the three contaminated sediments of Porto Marghera utilized in this study can undergo reductive dechlorination, probably mediated by indigenous sulfate-reducing and/or methanogenic bacteria.     

Abiotic reductive dechlorination of chlorinated ethylenes by soil

Abiotic reductive dechlorination of chlorinated ethylenes by soil in anaerobic environments was characterized to improve knowledge of the behavior of chlorinated ethylenes in natural systems, including systems modified to promote attenuation of contaminants. Target organics in the soil suspension reached sorption equilibrium in 2 days and the sorption isotherm of target organics was properly described by the linear sorption model. A modified Langmuir-Hinshelwood model was developed to describe the kinetics of reductive dechlorination of target organics by soil. The rate constants for the reductive dechlorination of chlorinated ethylenes at the reactive surfaces of reduced soils were found in the range between 0.055 (+/- 8.9%) and 2.60 (+/- 3.2%) day(-1). The main transformation products in reduced soil suspensions were C2 hydrocarbons. No chlorinated intermediates were observed at concentrations above detection limits. Five cycles of reduction of the soil followed by oxidation of the soil with trichloroethylene (TCE) did not affect the removal of TCE. The removal was affected by the reductants used and increased in the order: Fe(II) < dithionite < Fe(II) + dithionite.     

Anaerobic transformations and bioremediation of chlorinated solvents

Chlorinated aliphatic compounds, notably the chlorinated solvents, are common contaminants in soil and groundwater at hazardous waste sites. While these compounds are often recalcitrant, under favorable conditions they can be transformed and degraded through microbially mediated processes. There is great interest in understanding the transformations that are observed at contaminated sites and in manipulating these systems to achieve remediation. An important class of transformations occurs in anaerobic environments. Many of the transformations are reductive, and many yield useful energy to specific anaerobic bacteria. They include reductive dechlorination, dehydrochlorination and dichloroelemination. Of these, reductive dechlorination is often a growth-supporting reaction, while the others may be abiological or catalyzed by biological molecules. The reactions may result in chlorinated products, but there are often reaction sequences leading to completely dechlorinated products. The behavior of carbon tetrachloride (CT), 1,1,2,2-tetrachloroethane (TeCA) and the chloroethenes, perchloroethylene (PCE) and trichloroethylene (TCE), illustrate the range of anaerobic transformations that are possible, as well as the limited transformation that often is seen in the environment. CT undergoes reductive and substitutive reactions that are catalyzed by biological molecules but do not support bacterial growth. The anaerobic degradation of TeCA, which is a major contaminant at a site near Tacoma, WA, USA, provides examples of each type of transformation, and the products formed are consistent with the chlorinated compounds that are found in groundwater extraction wells. A laboratory study, using anaerobic sludge that had been fed chlorinated compounds, a cell-free extract from the sludge, and killed controls, showed that TeCA was transformed to four products and that these were further transformed, suggesting that it might be possible to degrade TeCA to innocuous products. Reductive dechlorination of PCE and TCE has been studied in many laboratories. Studies with mixed anaerobic consortia and with several dehalogenating bacteria, including strain 195 (. Isolation of a bacterium that reductively dechlorinates tetrachloroethane to ethane. Science 276, 1568-1571) that transforms PCE to ethene, have demonstrated that reductive dechlorination supports growth of the novel bacteria that carry out the reactions. Hydrogen has been shown to be an electron donor for the bacterial dehalogenation reactions, and kinetic and thermodynamic considerations indicate that dehalogenators can compete in some, but not all, anaerobic environments, pointing to applications of in situ bioremediation and to its limitations. Selected field studies of anaerobic transformations help delineate the applications of this type of bioremediation.     

Assessment of biogeochemical natural attenuation and treatment of chlorinated solvents, Altus Air Force Base, Altus, Oklahoma

Biogeochemical reductive dechlorination (BiRD) is a newly recognized method for the remediation or natural attenuation of chlorinated solvents. Chlorinated solvents are rapidly treated by abiotic reaction with reduced mineral iron sulfides. Iron sulfides are formed by naturally occurring sulfate-reducing bacteria when sufficient SO(4)(2-) and organic carbon are present or supplied to sediments containing mineral iron. An example of site characterization focusing on BiRD is presented focusing on mineral phases. Methods demonstrated here may be employed at other sites to evaluate naturally occurring BiRD or to evaluate an engineered BiRD remediation. A field investigation was performed at a TCE contaminated site at Altus AFB with naturally high concentrations of SO(4)(2-) and Fe(III) minerals and where an accidental fuel spill provided organic carbon. In the area of this fuel spill significant mineral iron sulfides were found, sulfate was almost completely removed, and TCE was absent. Only small amounts of daughter products were found, further indicating that the BiRD pathway was operative. Mass balance data indicates all of the remaining TCE (182 kg) could be treated by the remaining FeS (66.5 kg) in the upper aquifer; however, the FeS was not co-located with TCE to enable complete reaction. Laboratory microcosm tests with FeS amended and FeS-rich sediment from Altus AFB also suggest that BiRD is capable of destroying TCE. The results suggest that an engineered BiRD treatment is possible for this site.