Quantifying chlorinated ethene degradation during reductive dechlorination at Kelly AFB using stable carbon isotopes

Stable isotope analysis of chlorinated ethene contaminants was carried out during a bioaugmentation pilot test at Kelly Air Force Base (AFB) in San Antonio Texas. In this pilot test, cis-1,2-dichloroethene (cDCE) was the primary volatile organic compound. A mixed microbial enrichment culture, KB-1, shown in laboratory experiments to reduce chlorinated ethenes to non-toxic ethene, was added to the pilot test area. Following bioaugmentation with KB-1, perchloroethene (PCE), trichloroethene (TCE) and cDCE concentrations declined, while vinyl chloride (VC) concentrations increased and subsequently decreased as ethene became the dominant transformation product. Shifts in carbon isotopic values up to 2.7 per thousand, 6.4 per thousand, 10.9 per thousand and 10.6 per thousand were observed for PCE, TCE, cDCE and VC, respectively, after bioaugmentation, consistent with the effects of biodegradation. While a rising trend of VC concentrations and the first appearance of ethene were indicative of biodegradation by 72 days post-bioaugmentation, the most compelling evidence of biodegradation was the substantial carbon isotope enrichment (2.0 per thousand to 5.0 per thousand) in ?13C(cDCE). Fractionation factors obtained in previous laboratory studies were used with isotope field measurements to estimate first-order cDCE degradation rate constants of 0.12 h(-1) and 0.17 h(-1) at 115 days post-bioaugmentation. These isotope-derived rate constants were clearly lower than, but within a factor of 2-4 of the previously published rate constant calculated in a parallel study at Kelly AFB using chlorinated ethene concentrations. Stable carbon isotopes can provide not only a sensitive means for early identification of the effects of biodegradation, but an additional means to quantify the rates of biodegradation in the field.     

Assessing chlorinated ethene degradation in a large scale contaminant plume by dual carbon-chlorine isotope analysis and quantitative PCR

The fate of chlorinated ethenes in a large contaminant plume originating from a tetrachloroethene (PCE) source in a sandy aquifer in Denmark was investigated using novel methods including compound-specific carbon and chlorine isotope analysis and quantitative real-time polymerase chain reaction (qPCR) methods targeting Dehaloccocoides sp. and vcrA genes. Redox conditions were characterized as well based on concentrations of dissolved redox sensitive compounds and sulfur isotopes in SO(4)(2-). In the first 400 m downgradient of the source, the plume was confined to the upper 20 m of the aquifer. Further downgradient it widened in vertical direction due to diverging groundwater flow reaching a depth of up to 50 m. As the plume dipped downward and moved away from the source, O(2) and NO(3)(-) decreased to below detection levels, while dissolved Fe(2+) and SO(4)(2-) increased above detectable concentrations, likely due to pyrite oxidation as confirmed by the depleted sulfur isotope signature of SO(4)(2-). In the same zone, PCE and trichloroethene (TCE) disappeared and cis-1,2-dichloroethene (cDCE) became the dominant chlorinated ethene. PCE and TCE were likely transformed by reductive dechlorination rather than abiotic reduction by pyrite as indicated by the formation of cDCE and stable carbon isotope data. TCE and cDCE showed carbon isotope trends typical for reductive dechlorination with an initial depletion of (13)C in the daughter products followed by an enrichment of (13)C as degradation proceeded. At 1000 m downgradient of the source, cDCE was the dominant chlorinated ethene and had reached the source δ(13)C value confirming that cDCE was not affected by abiotic or biotic degradation. Further downgradient (up to 1900 m), cDCE became enriched in (13)C by up to 8 ‰ demonstrating its further transformation while vinylchloride (VC) concentrations remained low (<1 μg/L) and ethene was not observed. The correlated shift of carbon and chlorine isotope ratios of cDCE by 8 and 3.9 ‰, respectively, the detection of Dehaloccocides sp genes, and strongly reducing conditions in this zone provide strong evidence for reductive dechlorination of cDCE. The significant enrichment of (13)C in VC indicates that VC was transformed further, although the mechanism could not be determined. The transformation of cDCE was the rate limiting step as no accumulation of VC occurred. In summary, the study demonstrates that carbon-chlorine isotope analysis and qPCR combined with traditional approaches can be used to gain detailed insight into the processes that control the fate of chlorinated ethenes in large scale plumes.     

Dechlorination after thermal treatment of a TCE-contaminated aquifer: laboratory experiments

A microcosm study was conducted to evaluate dechlorination of trichloroethene (TCE) to ethene and survival of dechlorinating bacteria after a thermal treatment in order to explore the potential for post-thermal bioremediation. Unamended microcosms containing groundwater and aquifer material from a contaminated site dechlorinated TCE to cis-1,2-dichloroethene (cDCE), while lactate-amended microcosms dechlorinated TCE to cDCE or ethene. A thermal treatment was simulated by heating a sub-set of microcosms to 100 degrees C for 10d followed by cooling to 10 degrees C over 150 d. The heated microcosms demonstrated no dechlorination when unamended. However, when amended with lactate, cDCE was produced in 2 out of 6 microcosms within 300 d after heating. Dechlorination of TCE to cDCE thus occurred in fewer heated (2 out of 12) than unheated (10 out of 12) microcosms. In unheated microcosms, the presence of dechlorinating microorganisms, including Dehalococcoides, was confirmed using nested PCR of 16S rRNA genes. Dechlorinating microorganisms were detected in fewer microcosms after heating, and Dehalococcoides were not detected in any microcosms after heating. Dechlorination may therefore be limited after a thermal treatment in areas that have been heated to 100 degrees C. Thus, inflow of groundwater containing dechlorinating microorganisms and/or bioaugmention may be needed for anaerobic dechlorination to occur after a thermal treatment.     

Anaerobic dechlorination and redox activities after full-scale Electrical Resistance Heating (ERH) of a TCE-contaminated aquifer

The effects of Electrical Resistance Heating (ERH) on dechlorination of TCE and redox conditions were investigated in this study. Aquifer and groundwater samples were collected prior to and after ERH treatment, where sediments were heated to approximately 100 degrees C. Sediment samples were collected from three locations and examined in microcosms for 250 to 400 days of incubation. Redox activities, in terms of consumed electron acceptors, were low in unamended microcosms with field-heated sediments, although they increased upon lactate-amendment. TCE was not dechlorinated or stalled at cDCE with field-heated sediments, which was similar or lower compared to the degree of dechlorination in unheated microcosms. However, in microcosms which were bioaugmented with a mixed anaerobic dechlorinating culture (KB-1) and lactate, dechlorination past cDCE to ethene was observed in field-heated sediments. Dechlorination and redox activities in microcosms with field-heated sediments were furthermore compared with controlled laboratory-heated microcosms, which were heated to 100 degrees C for 10 days and then slowly cooled to 10 degrees C. In laboratory-heated microcosms, TCE was not dechlorinated and redox activities remained low in unamended and lactate-amended sediments, although organic carbon was released to the aqueous phase. In contrast, in field-heated sediments, high aqueous concentrations of organic carbon were not observed in unamended microcosms, and TCE was dechlorinated to cDCE upon lactate amendment. This suggests that dechlorinating microorganisms survived the ERH or that groundwater flow through field-heated sediments carried microorganisms into the treated area and transported dissolved organic carbon downstream.     

The need for bioaugmentation after thermal treatment of a TCE-contaminated aquifer: Laboratory experiments

A microcosm study was conducted to evaluate the need for bioaugmentation after a thermal treatment to anaerobically dechlorinate trichloroethene (TCE) to ethene. The microcosms were either: heated to 100 degrees C and slowly cooled to simulate thermal remediation while bioaugmenting when the declining temperature reached 10 degrees C; or kept at ambient groundwater temperatures (10 degrees C) and bioaugmented for comparison. Aquifer samples from three sediment locations within a TCE-polluted source zone were investigated in duplicate microcosms. In biostimulated (5 mM lactate) and heated microcosms, no conversion of TCE was observed in 4 out of 6 microcosms, and in the remaining microcosms the dechlorination of TCE was incomplete to cDCE (cis-dichloroethene). By comparison, complete TCE dechlorination to ethene was observed in 4 out of 6 heated microcosms that were bioaugmented with a highly enriched dechlorinating mixed culture, KB-1, but no electron donor, and also in 4 of 6 microcosms that were augmented with KB-1 and an electron donor (5 mM lactate). These data suggest that electron donor released during heating, was capable of promoting complete dechlorination coincident with bioaugmentation. Heated microcosms demonstrated less methanogenesis than unheated microcosms, even with elevated H2 concentrations and addition of KB-1, which contains methanogens. This suggests that the heating process suppressed the native microbial community, which can decrease competition with the bioaugmented culture and increase the effectiveness of dechlorination following a thermal treatment. Specifically, cDCE removal rates were four to six times higher in heated than unheated bioaugmented microcosms. This study confirms the need for bioaugmentation following a laboratory thermal treatment to obtain complete dechlorination of TCE.     

Comparison of an assay for Dehalococcoides DNA and a microcosm study in predicting reductive dechlorination of chlorinated ethenes in the field

The study aims to compare the detection of 16S rRNA gene of Dehalococcoides species and the microcosm study for biotransformation in predicting reductive dechlorination of chlorinated ethenes in ground water at hazardous waste sites. A total of 72 ground water samples were collected from 12 PCE or TCE contaminated sites in the United States. The samples were analyzed and used to construct microcosms in the laboratory. The results showed that the presence of Dehalococcoides DNA was well associated with dechlorination to ethene in the field. Nearly half of the wells where Dehalococcoides DNA was detected had ethene as a dechlorination end product. In comparison, for ground water samples of 16 wells where ethene was detected, ethene was produced in 11 of the corresponding microcosms. For most microcosms, during two years of incubation, dechlorination was less extensive than that observed in the field.     

Natural attenuation of chlorinated solvents at Area 6, Dover Air Force Base: groundwater biogeochemistry

Monitored natural attenuation (MNA) has recently emerged as a viable groundwater remediation technology in the United States. Area 6 at Dover Air Force Base (Dover, DE) was chosen as a test site to examine the potential for MNA of tetrachloroethene (PCE) and trichloroethene (TCE) in groundwater and aquifer sediments. A "lines of evidence" approach was used to document the occurrence of natural attenuation. Chlorinated hydrocarbon and biogeochemical data were used to develop a site-specific conceptual model where both anaerobic and aerobic biological processes are responsible for the destruction of PCE, TCE, and daughter metabolites. An examination of groundwater biogeochemical data showed a region of depleted dissolved oxygen with elevated dissolved methane and hydrogen concentrations. Reductive dechlorination likely dominated in the anaerobic portion of the aquifer where PCE and TCE levels were observed to decrease with a simultaneous increase in cis-1,2-dichloroethene (cis-DCE), vinyl chloride (VC), ethene, and dissolved chloride. Near the anaerobic/ aerobic interface, concentrations of cis-DCE and VC decreased to below detection limits, presumably due to aerobic biotransformation processes. Therefore, the contaminant and daughter product plumes present at the site appear to have been naturally atteuated by a combination of active anaerobic and aerobic biotransformation processes.     

Comparison between acetate and hydrogen as electron donors and implications for the reductive dehalogenation of PCE and TCE

Bioremediation by reductive dehalogenation of groundwater contaminated with tetrachloroethene (PCE) or trichloroethene (TCE) is generally carried out through the addition of a fermentable electron donor such as lactate, benzoate, carbohydrates or vegetable oil. These fermentable donors are converted by fermenting organisms into acetate and hydrogen, either of which might be used by dehalogenating microorganisms. Comparisons were made between H2 and acetate on the rate and extent of reductive dehalogenation of PCE. PCE dehalogenation with H2 alone was complete to ethene, but with acetate alone it generally proceeded only about half as fast and only to cis-1,2-dichloroethene (cDCE). Additionally, acetate was not used as an electron donor in the presence of H2. These findings suggest the fermentable electron donor requirement for PCE dehalogenation to ethene can be reduced up to 50% by separating PCE dehalogenation into two stages, the first of which uses acetate for the conversion of PCE to cDCE, and the second uses H2 for the conversion of cDCE to ethene. This can be implemented with a recycle system in which the fermentable substrate is added down-gradient, where the hydrogen being produced by fermentation effects cDCE conversion into ethene. The acetate produced is recycled up-gradient to achieve PCE conversion into cDCE. With the lower electron donor usage required, potential problems of aquifer clogging, excess methane production, and high groundwater chemical oxygen demand (COD) can be greatly reduced.     

Monitoring trichloroethene remediation at an iron permeable reactive barrier using stable carbon isotopic analysis

Stable carbon isotopic analysis, in combination with compositional analysis, was used to evaluate the performance of an iron permeable reactive barrier (PRB) for the remediation of ground water contaminated with trichloroethene (TCE) at Spill Site 7 (SS7), F.E. Warren Air Force Base, Wyoming. Compositional data indicated that although the PRB appeared to be reducing TCE to concentrations below treatment goals within and immediately downgradient of the PRB, concentrations remained higher than expected at wells further downgradient (i.e. >9 m) of the PRB. At two wells downgradient of the PRB, TCE concentrations were comparable to upgradient values, and delta13C values of TCE at these wells were not significantly different than upgradient values. Since the process of sorption/desorption does not significantly fractionate carbon isotope values, this suggests that the TCE observed at these wells is desorbing from local aquifer materials and was present before the PRB was installed. In contrast, three other downgradient wells show significantly more enriched delta13C values compared to the upgradient mean. In addition, delta13C values for the degradation products of TCE, cis-dichloroethene and vinyl chloride, show fractionation patterns expected for the products of the reductive dechlorination of TCE. Since concentrations of both TCE and degradation products drop to below detection limit in wells within the PRB and directly below it, these downgradient chlorinated hydrocarbon concentrations are attributed to desorption from local aquifer material. The carbon isotope values indicate that this dissolved contaminant is subject to local degradation, likely due to in situ microbial activity.     

Use of statistical tools to evaluate the reductive dechlorination of high levels of TCE in microcosm studies

A large, multi-laboratory microcosm study was performed to select amendments for supporting reductive dechlorination of high levels of trichloroethylene (TCE) found at an industrial site in the United Kingdom (UK) containing dense non-aqueous phase liquid (DNAPL) TCE. The study was designed as a fractional factorial experiment involving 177 bottles distributed between four industrial laboratories and was used to assess the impact of six electron donors, bioaugmentation, addition of supplemental nutrients, and two TCE levels (0.57 and 1.90 mM or 75 and 250 mg/L in the aqueous phase) on TCE dechlorination. Performance was assessed based on the concentration changes of TCE and reductive dechlorination degradation products. The chemical data was evaluated using analysis of variance (ANOVA) and survival analysis techniques to determine both main effects and important interactions for all the experimental variables during the 203-day study. The statistically based design and analysis provided powerful tools that aided decision-making for field application of this technology. The analysis showed that emulsified vegetable oil (EVO), lactate, and methanol were the most effective electron donors, promoting rapid and complete dechlorination of TCE to ethene. Bioaugmentation and nutrient addition also had a statistically significant positive impact on TCE dechlorination. In addition, the microbial community was measured using phospholipid fatty acid analysis (PLFA) for quantification of total biomass and characterization of the community structure and quantitative polymerase chain reaction (qPCR) for enumeration of Dehalococcoides organisms (Dhc) and the vinyl chloride reductase (vcrA) gene. The highest increase in levels of total biomass and Dhc was observed in the EVO microcosms, which correlated well with the dechlorination results.     

Stable hydrogen,carbon and chlorine isotope measurements of selected chlorinated organic solvents

Stable hydrogen isotopes of two chlorinated solvents, trichloroethylene (TCE) and 1,1,1-trichloroethane (TCA), provided by five different manufacturers, were determined and compared to their carbon and chlorine isotopic signatures. The isotope ratio for delta2H of different TCEs ranged between +466.9 per thousand and +681.9 per thousand, for delta13C between -31.57 per thousand and -27.37 per thousand, and for delta37Cl between -3.19 per thousand and +3.90 per thousand. In the case of the TCAs, the isotope ratio for delta2H ranged between -23.1 per thousand and +15.1 per thousand, for delta13C between -27.39 per thousand and -25.84 per thousand, and for delta37Cl between -3.54 per thousand and +1.39 per thousand. As well, a column experiment was carried out to dechlorinate tetrachloroethylene (PCE) to TCE using iron. The dechlorination products have completely different hydrogen isotope ratios than the manufactured TCEs. Compared to the positive values of delta2H in manufactured TCEs (between +466.9 per thousand and +681.9 per thousand), the dechlorinated products had a very depleted delta2H (less than -300 per thousand). This finding has strong implications for distinguishing dechlorination products (PCE to TCE) from manufactured TCE. In addition, the results of this study show the potential of combining 2H/1H analyses with 13C/12C and 37Cl/35Cl for isotopic fingerprinting applications in organic contaminant hydrogeology.     

Variability in microbial carbon isotope fractionation of tetra- and trichloroethene upon reductive dechlorination

The variability of stable carbon isotope fractionation upon reductive dechlorination of tetra- and trichloroethene by several microbial strains was investigated to examine the uncertainties related to the in situ application of compound specific isotope analysis (CSIA) of chlorinated ethenes. Carbon isotope fractionation was investigated with a set of microorganisms representative for the currently known diversity of dehalorespirers: Dehalococcoides ethenogenes strain 195, Desulfitobacterium sp. strain Viet1, Desulfuromonas michiganensis and Geobacter lovleyi sp. strain SZ and compared to the previous reports using Sulfurospirillum spp. and Desulfitobacterium sp. strain PCE-S. Carbon isotope fractionation of tetrachloroethene (PCE) and trichlorethene (TCE) was highly variable ranging from the absence of significant fractionation to carbon isotope fractionation (epsilonC) of 16.7 and 3.5-18.9 for PCE and TCE, respectively. Fractionation of both compounds by D. ethenogenes strain 195 (PCE: epsilonC=6.0; TCE: epsilonC=13.7) was similar to the literature data for mixed cultures containing Dehalococcoides spp. D. michiganensis (PCE: no significant fractionation; TCE: epsilonC=3.5) and G. lovleyi sp. strain SZ (PCE no significant fractionation; TCE: epsilonC=8.5) generated the lowest fractionation of all studied strains. Desulfitobacterium sp. strain Viet1 (PCE: epsilonC=16.7) gave the highest enrichment factor for PCE.     

Aerobic biodegradation of dichloroethenes by indigenous bacteria isolated from contaminated sites in Africa

The widespread use of tetrachloroethene (PCE) and trichloroethene (TCE) as dry cleaning solvents and degreasing agents for military and industrial applications has resulted in significant environmental contamination worldwide. Anaerobic biotransformation of PCE and TCE through reductive dechlorination frequently lead to the accumulation of dichloroethenes (DCEs), thus limiting the use of reductive dechlorination for the biotransformation of the compounds. In this study, seven bacteria indigenous to contaminated sites in Africa were characterized for DCE degradation under aerobic conditions. The specific growth rate constants of the bacterial isolates ranged between 0.346-0.552d(-1) and 0.461-0.667d(-1) in cis-DCE and trans-DCE, respectively. Gas chromatographic analysis revealed that up to 75% of the compounds were degraded within seven days with the degradation rate constants ranging between 0.167 and 0.198d(-1). The two compounds were also observed to be significantly degraded, simultaneously, rather than sequentially, when present as a mixture. Phylogenetic analysis of the 16S rRNA gene sequences of the bacterial isolates revealed their identity as well as their relation to other environmentally-important bacteria. The observed biodegradation of DCEs may contribute to PCE and TCE removal at the aerobic fringe of groundwater plumes undergoing reductive dechlorination in contaminated sites.     

Effect of source variability and transport processes on carbon isotope ratios of TCE and PCE in two sandy aquifers

Chlorinated ethenes often migrate over extended distances in aquifers and may originate from different sources. The aim of this study was to determine whether stable carbon isotope ratios remain constant during dissolution and transport of chlorinated ethenes and whether the ratios can be used to link plumes to their sources. Detailed depth-discrete delineation of the carbon isotope ratio in a tetrachloroethene (PCE) plume and in a trichloroethene (TCE) plume was done along cross-sections orthogonal to groundwater flow in two sandy aquifers in the Province of Ontario, Canada. At the TCE site, TCE concentrations up to solubility were measured in one high concentration zone close to the bottom of the aquifer from where dense non-aqueous phase liquid (DNAPL) was collected. A laboratory experiment using the DNAPL indicated that only very small carbon isotope fractionation occurs during dissolution of TCE (0.26 per thousand), which is consistent with field observations. At most sampling points, the delta(13)C of dissolved TCE was similar to that of the DNAPL except for a few sampling points at the bottom of the aquifer close to the underlying aquitard. At these points, a (13)C enrichment of up to 2.4 per thousand was observed, which was likely due to biodegradation and possibly preferential diffusion of TCE with (12)C into the aquitard. In contrast to the TCE site, several distinct zones of high concentration were observed at the PCE site and from zones to zone, the delta(13)C values varied substantially from -24.3 per thousand to -33.6 per thousand. Comparison of the delta(13)C values in the high concentration zones made it possible to divide the plume in the three different domains, each probably representing a different episode and location of DNAPL release. The three different zones could still be distinguished 220 m from the DNAPL sources. This demonstrates that carbon isotope ratios can be used to differentiate between different zones in chlorinated ethene plumes and to link plume zones to their sources. In addition, subtle variations in delta(13)C at plume fringes provided insight into mechanisms of plume spreading in transverse vertical direction. These variations were identified because of the high-resolution provided by the monitoring network.     

Variations in expression of carbon isotope fractionation of chlorinated ethenes during biologically enhanced PCE dissolution close to a source zone

The stable carbon isotope values of tetrachloroethene (PCE) and its degradation products were monitored during studies of biologically enhanced dissolution of PCE dense nonaqueous phase liquid (DNAPL) to determine the effect of PCE dissolution on observed isotope values. The degradation of PCE was monitored in a 2-dimensional model aquifer and in a pilot test cell (PTC) at Dover Air Force Base, both with emplaced PCE DNAPL sources. Within the plume down gradient from the source, the isotopic fractionation of dissolved PCE and its degradation products were consistent with those observed in biodegradation laboratory studies. However, close to the source zone significant shifts in the isotope values of dissolved PCE were not observed in either the model aquifer or PTC due to the constant input of newly dissolved, non fractionated PCE, and the small isotopic fractionation associated with PCE reductive dechlorination by the mixed microbial culture used. Therefore the identification of reductive dechlorination in the presence of PCE DNAPL was based upon the appearance of daughter products and the isotope values of those daughter products. An isotope model was developed to simulate isotope values of PCE during the dissolution and degradation of PCE adjacent to a DNAPL source zone. With the exception of very high degradation rate constants (>1/day) stable carbon isotope values of PCE estimated by the model remained within error of the isotope value of the PCE DNAPL, consistent with measured isotope values in the model aquifer and in the PTC.     

Carbon isotope fractionation during reductive dechlorination of TCE in batch experiments with iron samples from reactive barriers

Reductive dechlorination of trichloroethene (TCE) by zero-valent iron produces a systematic enrichment of 13C in the remaining substrate that can be described using a Rayleigh model. In this study, fractionation factors for TCE dechlorination with iron samples from two permeable reactive barriers (PRBs) were established in batch experiments. Samples included original unused iron as well as material from a barrier in Belfast after almost 4 years of operation. Despite the variety of samples, carbon isotope fractionations of TCE were remarkably similar and seemed to be independent of iron origin, reaction rate, and formation of precipitates on the iron surfaces. The average enrichment factor for all experiments was -10.1 per thousand (+/- 0.4 per thousand). These results indicate that the enrichment factor provides a powerful tool to monitor the reaction progress, and thus the performance, of an iron-reactive barrier over time. The strong fractionation observed may also serve as a tool to distinguish between insufficient residence time in the wall and a possible bypassing of the wall by the plume, which should result in an unchanged isotopic signature of the TCE. Although further work is necessary to apply this stable isotope method in the field, it has potential to serve as a unique monitoring tool for PRBs based on zero-valent iron.     

Carbon and hydrogen isotope effects during sorption of organic contaminants on carbonaceous materials

Stable carbon and hydrogen isotopes can be an efficient means to validate biodegradation of organic contaminants in groundwater since it results in an isotopic fractionation. A prerequisite in applying this method in the field is the proof that other processes decreasing the contaminant concentration are conservative with respect to isotope effects. In this paper we show for carbon isotopes of halogenated hydrocarbon compounds [trichloroethene (TCE), cis-dichloroethene (c-DCE), vinylchloride (VC)] and carbon and hydrogen isotopes of BTEX compounds (benzene, toluene, p-xylene) that no significant fractionation occurs during equilibrium sorption onto activated carbon, lignite coke and lignite. In general, effects were in the range of the reproducibility limit of the analytical instrument (0.5 per thousand for delta13C, and 8 per thousand for delta2H). This observation was made for fractions sorbed of less than 5% to more than 95%. Also for rate-limited sorption of TCE onto activated carbon, no significant fractionation in carbon isotopes could be observed. These findings support the assumption that for these classes of compounds, sorption processes in aquifer systems are conservative with respect to isotope effects.     

Enhanced 1,2-dichloroethane degradation in heavy metal co-contaminated wastewater undergoing biostimulation and bioaugmentation

Biostimulation, bioaugmentation and dual-bioaugmentation strategies were investigated in this study for efficient bioremediation of water co-contaminated with 1,2-dichloroethane (1,2-DCA) and heavy metals, in a microcosm set-up. 1,2-DCA concentration was periodically measured in the microcosms by gas chromatographic analysis of the headspace samples, while bacterial population and diversity were determined by standard plate count technique and Polymerase chain reaction and denaturing gradient gel electrophoresis (PCR–DGGE) analysis, respectively. Dual-bioaugmentation, proved to be most effective exhibiting 22.43%, 26.54%, 19.58% and 30.49% increase in 1,2-DCA degradation in microcosms co-contaminated with As³⁺, Cd²⁺, Hg²⁺ and Pb²⁺, respectively, followed by bioaugmentation and biostimulation. Dual-bioaugmented microcosms also exhibited the highest increase in the biodegradation rate constant (k₁) resulting in 1.76-, 2-, 1.7- and 2.1-fold increase in As³⁺, Cd²⁺, Hg²⁺ and Pb²⁺ co-contaminated microcosms respectively, compared to the untreated microcosms. Dominant bacterial strains obtained from the co-contaminated microcosms were found to belong to the genera Burkholderia, Pseudomonas, Bacillus, Enterobacter and Bradyrhizobium, previously reported for 1,2-DCA and other chlorinated compounds degradation. PCR–DGGE analysis revealed variation in microbial diversity over time in the different co-contaminated microcosms. Results obtained in this study have significant implications for developing innovative bioremediation strategies for treating water co-contaminated with chlorinated organics and heavy metals.     

In situ sequential treatment of a mixed contaminant plume

Groundwater plumes often contain a mixture of contaminants that cannot easily be remediated in situ using a single technology. The purpose of this research was to evaluate an in situ treatment sequence for the control of a mixed organic plume (chlorinated ethenes and petroleum hydrocarbons) within a Funnel-and-Gate. A shallow plume located in the unconfined aquifer at Alameda Point, CA, was found to contain up to 218,000 μg/l of cis-1,2 dichloroethene (cDCE), 16,000 μg/l of vinyl chloride (VC) and <1000 μg/l of 1,1 dichloroethene (1,1 DCE), trans-1,2 dichloroethene (trans-1,2 DCE) and trichloroethene (TCE). Total benzene, toluene, ethylbenzene and xylenes (BTEX) concentrations were <10,000 μg/l. Contaminated groundwater was funneled into a gate, 3.0 m wide, 4.5 m long and 6.0 m deep (keyed into the underlying aquitard) where treatment occurred. The initial gate segment consisted of granular iron, for the reductive dechlorination of the higher chlorinated ethenes. The second segment, the biosparge zone, promoted aerobic biodegradation of petroleum hydrocarbons and any remaining lesser-chlorinated compounds, stimulated by dissolved oxygen (DO) and carbon dioxide (CO₂) additions via an in situ sparge system (CO₂ was used to neutralize the high pH produced from reactions in the iron wall). Groundwater was drawn through the gate by pumping two wells located at the sealed, downgradient, end. Over a 4-month period an estimated 1350 g of cDCE flowed into the treatment gate and the iron wall removed 1230 g, or 91% of the mass. The influent mass of VC was 572 g and the iron wall removed 535 g, corresponding to 94% mass removal. The other chlorinated ethenes had significantly lower influent masses (3 to 108 g) and the iron wall removed the majority of the mass resulting in >96% mass removal for any of the compounds. In spite of these high removal percentages, laboratory column tests indicated that at these levels of chlorinated contaminants, surface saturation of the iron grains likely contributed to lower than expected reaction rates. In the biosparge zone, mass removal of cDCE appeared to occur predominantly by biodegradation (65%) with volatilization (35%) being an important secondary process. The dominant removal process for VC was volatilization (70%) although significant biodegradation was also indicated (30%). Laboratory microcosm results confirmed the potential for aerobic biodegradation of cDCE and VC. When average influent field concentrations for cDCE and VC were 220,000 and 46,000 μg/l, respectively, the sequential treatment unit removed 99.6% of the total mass and when the influent concentrations decreased to 26,000 and 19,000 μg/l for cDCE and VC, respectively, >99.9% removal within the treatment gate was attained. BTEX compounds were found to be significantly retarded in the iron treatment zone. Although they did eventually break through the granular iron, and into the gravel transition zone, none of these compounds was detected in the biosparge zone. No noticeable interferences between the anaerobic (reductive) and aerobic parts of the system occurred during testing. The results of this experiment show that in situ treatment sequences are viable, although further work is needed to optimize performance.