高热值城市生活垃圾归类分流处置的能值分析

生活垃圾处理已成为限制城市化进程和城市经济发展的重大问题之一,采用垃圾归类分流处置方法可以有效地促进垃圾减量化和资源化的效果。以西安市典型高校校园生活垃圾为代表性高热值焚烧型城市生活垃圾,通过绘制能值系统图辨析卫生填埋-沼气发电、焚烧发电、生物质燃料混烧发电等3种垃圾处理系统的能值投入和产出过程。依据垃圾物理组成和热值数据分别计算了2种处理系统的能值产出率、环境负载率、能值投资率、可更新能源投入率和能值可持续指数等5项基本能值指标,并从能量利用的角度对3种生活垃圾处理方法的环境可持续性与经济竞争力进行了比较分析。能值分析结果表明,采用生活垃圾焚烧和生物质燃料混烧发电处理法在能量转化效率和环境影响方面具有显著优势,对高热值焚烧型生活垃圾采用"归类分流-集中焚烧处理"的方式有利于提高城市生活垃圾减量化处理的环境效益与经济收益。     

成都周边农村生活垃圾的特性、村民意识与处置模式研究

对四川成都周边100 km内8个典型农村的生活垃圾处理现状、特性、认知和处理意愿进行调查,探讨了适合城市环境下农村生活垃圾的处理与处置模式。结果表明:虽然在临城地区有收集设施,但是离城区稍远、交通不便的地区,农村生活垃圾仍以自然堆放和自行焚烧为主;成都周边农村人均垃圾日产量在58.9~406.8 g/(人·d)波动,垃圾中有机、无机组分和可回收组分质量分数平均分别为71.82%、5.17%、22.35%,垃圾的含水率、p H、有机质质量分数、灰分质量分数、热值分别为36.64%~75.15%、6.16%~7.66%、59.03%~85.94%、13.27%~41.92%、5 134.6~10 803.4 k J/kg,呈现"两高一低"(即高含水率、高有机组分、低无机组分)的特点。调查区90.6%村民认为周围环境已受到垃圾污染,62.7%村民认为生活垃圾处理很必要且愿意支付一定的金额。为此,构建了以分类为前提的分散处理和集中处置相结合的模式。     

机械淋滤-厌氧生物组合工艺处理有机生活垃圾中试研究

采用机械淋滤/厌氧生物组合工艺,充分发挥机械淋滤反应器的水解酸化功能和厌氧生物反应器的产甲烷功能,对有机生活垃圾进行了中试规模处理。厌氧生物反应器经过接种,15 d驯化完成。厌氧反应器出水回流淋洗水量对机械淋滤反应器运行特征有较大影响,当回流淋洗水量为3.0 m3/d时,淋滤液COD、VFA第8天时浓度分别为41 000 kg/L和2 000 kg/L。对机械淋滤反应器/厌氧反应器组合工艺进行了多批次实验,每吨有机生活垃圾平均产生沼气87.2 m3,甲烷含量稳定在75%,平均产沼系数为0.46 m3/kg COD,厌氧生物反应器出水COD平均值为560 mg/L,在对有机生活垃圾处理的同时实现有机生活垃圾资源化利用。     

Fenton-聚硅铝铁硼处理生活垃圾压滤液研究

以正交设计方法为基础，以COD去除率为指标，确定了聚硅铝铁硼（PSAFB）最优制备条件，研究了Fenton-PSAFB混凝法处理城市生活垃圾压滤液的最优反应条件和处理效果。结果表明：以200 mL生活垃圾压滤液为处理对象，复合絮凝剂PSAFB的最优制备工艺条件为：Al/Si为1/2，Fe/Si为1/2，B/Si为1/6；其最优反应条件为：pH值为5.0，投加量为200 mg/L（以SiO₂计)；Fenton法最优反应条件为：pH值为3.0，30%H₂O₂为20 mL，1 mol/L FeSO₄为30 mL；采用最优反应条件的Fenton-PSAFB处理垃圾压滤液，浊度去除率达到95.2%，COD去除率达到84.2%，BOD₅去除率达到81.5%。     

城市生活垃圾处理方法及经济分析

本文通过对国内外城市生活垃圾处理处置技术和经济费用分析,认为焚烧法处理技术投资费用大,仅个别城市有条件采用;卫生填埋和堆肥技术处理生活垃圾技术设备简单,投资费用较少,垃圾处理量大,土地还可以重复利用,比较适合国情。     

国内最大的垃圾焚烧厂日前在上海点火投产

既能无污染处理垃圾又能用来发电的国内最大垃圾焚烧厂日前在上海点火投产。坐落在上海西郊江桥的生活垃圾焚烧厂占地 2 0 0余亩 ,政府投资额为 2 .4亿元人民币 ,一期工程生活垃圾日处理能力为 10 0 0 t,年处理垃圾可达 33万 t,其垃圾处理服务范围可覆盖上海 1/ 3的城市面积。二期工程建成后 ,将达到日处理垃圾 15 0 0 t的规模。上海生活垃圾日产生量达到万 t,而此前 7成以上都用来填埋。填埋处理既占用大量土地资源 ,环保性也不高。新点火的上海江桥生活垃圾焚烧厂采用焚烧、生化、填埋综合方式来处理垃圾。其烟气排放严格执行欧盟标准 ,废…     

四川城市生活垃圾重金属污染状况及来源分析

四川省作为西南粮食生产大省,土壤重金属污染问题备受关注,生活垃圾处理处置可能带来的土壤污染风险急需探明。结合四川省五大经济区的发展格局和多样的地形条件,研究了成都、宜宾、南充、达州、西昌、马尔康城市夏冬两季生活垃圾的物理组成、重金属含量及垃圾主要组分受污染状况。结果表明,四川地区生活垃圾中厨余、包装纸、卫生纸、橡塑和灰土是主要组分,共占总量的78.25%~96.92%;四川地区垃圾中Cu(14.23~107.56 mg/kg)、Cd(0.07~0.63 mg/kg)、Zn(53.77~338.30 mg/kg)、Hg(0.01~0.41 mg/kg)和Cr(35.39~179.63 mg/kg)浓度较高,易造成土壤污染。以土壤环境质量农业用地标准为参照计算得出的重金属污染负荷指数表明:仅夏季宜宾生活垃圾处于Ⅰ级中度污染;四川地区夏冬季总体处于无污染水平,且夏季污染负荷指数略高。通过测定垃圾主要组分中重金属含量,发现厨余和灰土是成都夏季垃圾中Cd的主要来源,灰土是四川地区垃圾中Cu、Zn和Cr的主要来源之一,燃煤产生的灰土是西昌冬季垃圾中Hg的主要来源。     

三峡库区农村生活垃圾处理支付意愿及影响因素分析

农村生活垃圾的集中化、科学化处理对改善农村居民生活环境和农业生产环境具有重要意义。而农户对农村生活垃圾处理的支付意愿对农村生活环境的改善具有关键性作用。采用条件价值评估法(CVM)分析了三峡库区农户对处理生活垃圾的支付意愿及其影响因素。结果表明:(1)农户对农村生活垃圾处理的平均支付意愿为48元/a;(2)户主年龄、文化程度以及对环境是否关心对当地农户处理生活垃圾的支付意愿有极显著影响。户主年龄和文化程度对生活垃圾处理的支付意愿的影响为正,说明农户年龄越大、文化程度越高,对生活垃圾处理的支付意愿就越强烈。农户对环境的关心程度为正,表示农户越关心环境,对生活垃圾处理的支付意愿就越强烈。最后,提出相关建议:制定政策时要充分考虑农户的个体特征和自身利益;加强教育,提高农户的文化水平;加强环境保护宣传,提高农户的环境认知和环保意识。     

城市垃圾能的利用途径

一、垃圾的潜能 世界城市垃圾同人口的增长一样,达到创记录的水平。如何处理堆积如山的垃圾以及利用其资源和能源,是市政建设中的重要问题。 以前,垃圾处理主要靠填坑或堆置,但是,在城市附近,适于这样处置的场所越来越少。目前,为了减量和进行无害化处理,垃圾的焚烧方法用得越来越广。随着生活水平的提高,垃圾的发热量也在逐步提高,更适于进行焚烧处置。例如,1964年时,日本     

上海市试点小区湿垃圾源头减量前后垃圾处理处置全链条碳足迹分析

上海市于2019年7月率先开始实施垃圾分类工作,湿垃圾的分类与处理是垃圾分类的痛点问题。在小区垃圾分类站,采用食物垃圾粉碎处理器对湿垃圾进行固液分相处理是实现湿垃圾源头减量处理的试点措施。为了进一步探究在不同模式下垃圾源头减量处理前后的碳排放情况,根据联合国气候变化政府间专家委员会(IPCC)制定的《2006年IPCC国家温室气体清单指南》(简称IPCC指南(2006)),并通过生命周期法对上海市普陀区甘泉街道3个试点小区(2365户)进行传统混收混运处理和湿垃圾源头减量2种处理模式下为期1年的对比评估与分析。结果表明,与传统混收混运处理模式相比,湿垃圾源头减量模式处理1 t原生垃圾可多发电7.8 kWh,减少固体清运量0.3 t,减少净碳排放量(CO_2)1.57×10~(-2) t。以上海市垃圾产量2.1×10~4 t·d~(-1)计,该模式可多发电1.64×10~5 kWh·d~(-1),减少固体清运量6 300 t,减少净碳排放量330.5 t CO_2。基于固液分相的湿垃圾源头减量处理模式,对降低生活垃圾处理处置全链条碳排放具有重要作用。以上研究结果可为我国垃圾分类与处理提供必要的数据支撑。     

Municipal solid waste characteristics and management in China

The purpose of this investigation is to evaluate the current status and identify the problems of municipal solid waste (MSW) management in China in order to determine appropriate remedial strategies. This is the first of two papers, discussing primarily the general characteristics of MSW and its management in China. The second paper focuses on specific remedial strategies. MSW generation in China has increased rapidly in the past 20 years from 31.3 million tons in 1980 to 113.0 million tons in 1998. The annual rate of increase is 3-10%. The average generation per capita is 1.0 kg/day (0.38 t/year). Nearly one-half of the waste generated is dumped in the suburbs, where the accumulated quantity has reached 6 billion tons, which has caused heavy environmental pollution. This paper provides information on MSW management in China, such as MSW generation and its physical, chemical, and biological properties. Low calorific value and high moisture content characterize China's municipal waste. Other issues related to MSW management in China are also discussed, including the factors that influence MSW generation quantity and     

垃圾焚烧炉干燥段通风阻力特性实验研究

倾斜往复式炉排是我国城市生活垃圾焚烧炉中经常采用的炉排形式之一。垃圾在炉排干燥段的干燥效果直接影响到其着火和燃烧,因此炉排下侧送出的一次风在垃圾层中的流通性显得尤其重要。本研究通过搭建冷态试验台,以Steinmuller炉排为例,测量了炉排和不同厚度的垃圾层在不同一次风流量下的阻力,并研究了炉排和垃圾层的通风阻力特性,为今后更好地组织和控制高水份垃圾在炉内的干燥预热和着火燃烧提供了设计依据。     

Municipal Solid Waste Characteristics and Management in China

ABSTRACT

The purpose of this investigation is to evaluate the current status and identify the problems of municipal solid waste (MSW) management in China in order to determine appropriate remedial strategies. This is the first of two papers, discussing primarily the general characteristics of MSW and its management in China. The second paper focuses on specific remedial strategies. MSW generation in China has increased rapidly in the past 20 years from 31.3 million tons in 1980 to 113.0 million tons in 1998. The annual rate of increase is 3–10%. The average generation per capita is 1.0 kg/day (0.38 t/year). Nearly one-half of the waste generated is dumped in the suburbs, where the accumulated quantity has reached 6 billion tons, which has caused heavy environmental pollution. This paper provides information on MSW management in China, such as MSW generation and its physical, chemical, and biological properties. Low calorific value and high moisture content characterize China's municipal waste. Other issues related to MSW management in China are also discussed, including the factors that influence MSW generation quantity and quality, MSW collection, transfer and transport, treatment and disposal, material recovery, legislation, enforcement, and administration.     

城市生活垃圾压缩站环境污染研究

通过对垃圾压缩站内生活垃圾进行采样分析、压实试验和环境污染检测，得出了城市生活垃圾压实密度和施加压力的关系曲线，确定了对垃圾压实的合适压力范围为0．1～0．2MPa；垃圾压缩站环境污染严重，垃圾压缩污水量为10-50kg／t，其中BOD5和COD平均分别超标111倍和486倍；环境噪音只有50m以外才能达到居民区环境质量二级标准（60dB（A））的噪音要求；产生的臭气在较低风速下一般扩散25m时污染达到最大，NH3、H2S分别可以达到0．011、0．0046mg／m^3，这个值占容许浓度的55％和46％。     

Modelling of PCDD/F release from MSW bio-drying

In the present work, an experimentation was carried out to study the behaviour of PCDD/F during the process of municipal solid waste (MSW) bio-drying. This process belongs to the biological mechanical treatment (BMT) options and is aimed to the dewatering of MSW thanks to the biological exothermal reactions (thermal drying, on the contrary, needs an external heat source as methane). The result is a decrease of waste weight and an increase of lower heating value (as the energy content refers to a lower amount of waste). Of course, the overall energy availability does not increase, but the characteristics of bio-drying are interesting as a way for refuse derived fuel generation: glass, metals and inert removals are easier after bio-drying. The literature of the sector shows only few data on PCDD/F emission to air from BMT. Anyway, in the present work an original theory has been put forward in order to explain the enrichment of PCDD/F in the air exiting the biological processes. The role of the initial PCDD/F concentration in the ambient air entering the plant is obviously taken into account. The results of the developed experimentation and the following elaborations point out that PCDD/F could be freed from the volatile solids consumed during the process. The different amount of PCDD/F in the waste and the different consumption of volatile solids depending on the biological process can explain the different PCDD/F emission factors available in the literature.     

城市垃圾预处理改善焚烧特性的探讨

针对目前我国城市垃圾的高水分、低热值的特性,提出了2种改善城市垃圾焚烧特性的有效措施:生物质垃圾源分类和生物干燥.在我国建立生物质垃圾源分类体系,将生物质垃圾源头分类后,剩余垃圾的热值可以提高约50%～120%,已适合直接入炉焚烧,同时分离出来的生物质垃圾也更易于好氧堆肥或厌氧消化.另外一项技术措施是在焚烧前利用生物干燥技术,降低城市垃圾的水分含量,提高入炉垃圾的热值,这种方法主要是利用生物反应热来干燥城市生活垃圾,只需要在垃圾投入焚烧炉前增加一个预处理步骤,不必改变目前的垃圾收运体系,而且进行生物干燥后的垃圾更易于分选其中的可回收物质.     

Life cycle and economic assessment of source-separated MSW collection with regard to greenhouse gas emissions: a case study in China

In China, the continuously increasing amount of municipal solid waste (MSW) has resulted in an urgent need for changing the current municipal solid waste management (MSWM) system based on mixed collection. A pilot program focusing on source-separated MSW collection was thus launched (2010) in Hangzhou, China, to lessen the related environmental loads. And greenhouse gas (GHG) emissions (Kyoto Protocol) are singled out in particular. This paper uses life cycle assessment modeling to evaluate the potential environmental improvement with regard to GHG emissions. The pre-existing MSWM system is assessed as baseline, while the source separation scenario is compared internally. Results show that 23 % GHG emissions can be decreased by source-separated collection compared with the base scenario. In addition, the use of composting and anaerobic digestion (AD) is suggested for further optimizing the management of food waste. 260.79, 82.21, and ?86.21 thousand tonnes of GHG emissions are emitted from food waste landfill, composting, and AD, respectively, proving the emission reduction potential brought by advanced food waste treatment technologies. Realizing the fact, a modified MSWM system is proposed by taking AD as food waste substitution option, with additional 44 % GHG emissions saved than current source separation scenario. Moreover, a preliminary economic assessment is implemented. It is demonstrated that both source separation scenarios have a good cost reduction potential than mixed collection, with the proposed new system the most cost-effective one.     

城市生活垃圾并流竖炉焚烧模拟实验研究

气化熔融焚烧技术能够避免重金属和二恶英的二次污染，被公认为实现零排放和环境友好型的焚烧方法。在这样的背景下提出了生活垃圾并流竖炉气化熔融焚烧工艺。该工艺以竖炉为气化熔融主体设备，垃圾料层与助燃空气在炉内都是至上而下并流流动，从而使垃圾热解气化产生的可燃气体在竖炉下部完全燃烧，以提供灰渣熔融耗热。并流竖炉热态模拟试验表明，并流时垃圾料层中各点的温度明显高于逆流情况，并流时产生的CO₂量明显高于逆流情况。因此说并流竖炉更适合气化熔融焚烧工艺的要求。     

Optimization for municipal solid waste treatment based on energy consumption and contaminant emission

This paper analyzes the characterization of energy consumption and contaminant emissions from a municipal solid waste (MSW) treatment system that comprises transfer station, landfill site, combustion plant, composting plant, dejecta treatment station, and an integrated MSW treatment plant. The consumed energy and energy medium materials were integrated under comprehensive energy consumption (CEC) for comparison. Among typical MSW disposal methods such as combustion, composting, and landfilling, landfilling has the minimum CEC value. Installing an integrated treatment plant is the recommended MSW management method because of its lower CEC. Furthermore, this method is used to ensure process centralization. In landfill sites, a positive linear correlation was observed between the CEC and contaminant removal ratios when emitted pollutants have a certain weight coefficient. The process should utilize the minimum CEC value of 5.3702 kgce/t MSW and consider energy consumption, energy recovery, MSW components, and the equivalent of carbon dioxide emissions.     

北京市朝阳区城市生活垃圾组分分布特性研究

针对垃圾焚烧的需要，按垃圾组分低位热值重新进行了垃圾分类，检验了各组分的正态分布特性，得出了服从正态分布的垃圾组分的概率分布密度函数。进行了垃圾含水率的线性相关性分析，认为垃圾含水率与厨余的相关性最大，降水量对含水率影响不大。