金属离子对有机垃圾两相厌氧系统中UASB处理效果的促进作用

在"水解溶出 UASB反应器"处理城镇有机垃圾的两相厌氧系统中,向UASB反应器进水中添加K、Mg、Fe、Co、Ni 5种金属离子的组合促进剂,通过对UASB反应器容积负荷、产气量、产甲烷量在添加组合促进剂前后的比较,研究了组合促进剂(K、Mg、Fe、Co、Ni)对有机垃圾浸出液厌氧消化过程的促进作用.试验结果表明,添加组合促进剂后,反应器的平均容积负荷从12.89 kg COD/m3·d提高到17.79 kg COD/m3·d;平均污泥负荷从0.82 kg COD/kg VSS·d提高到1.07 kg COD/kg VSS·d.此外,平均每千克COD产气量为392.5 L,比添加组合促进剂之前增大了6.4%;而平均每千克COD产甲烷量为297.5 L,比添加组合促进剂之前增大了10.5%.对于氨氮、挥发性脂肪酸(VFA)、pH及碱度来说,在添加组合促进剂之后则无大的变化.     

外循环式UASB反应器处理槟榔废水

在中温（35±2℃）条件下,利用外循环式UASB反应器处理中高有机浓度的槟榔加工废水,并着重探讨了水力停留时间（HRT）对厌氧消化的影响。研究表明,当反应器稳定运行,水力停留时间为1 d,进水COD浓度5 000 mg/L左右,容积负荷在2.53-5.25 kg COD/（m3·d）时,COD去除率在38%以上,出水COD〈3 000 mg/L,平均产气率为0.41 m3/kg COD;若水力停留时间延长至4 d,容积负荷为1.26-1.30 kg COD/（m3·d）,COD去除率可以达到79%,出水COD〈1 200 mg/L,出水可生化性下降,BOD5/COD平均为0.28,实验取得了良好的处理效果,为利用厌氧技术处理槟榔加工废水提供了设计依据。     

CLR+立式A~3/O~3-MBR组合工艺处理垃圾渗滤液的工程实例

介绍了一种以沼气提升厌氧反应器(CLR)+立式A~3/O~3-MBR为核心的垃圾渗滤液处理组合工艺,该工艺对垃圾渗滤液有着良好的处理效能。在实际运行过程中,CLR单元对COD负荷的变化有着较好的适应能力,能够高效去除渗滤液中的有机污染物。当进水负荷为6~8 kg COD/(m~3·d)时,CLR出水COD、VFA和SS可以分别低于5 000、1 000和2 000 mg/L,COD去除率维持在90%左右。立式A~3/O~3-MBR能够进一步去除CLR厌氧出水中的氨氮和有机物,组合工艺出水中的COD500 mg/L,BOD5300 mg/L,NH_4~+-N35 mg/L,TP8 mg/L,各指标完全符合设计要求,且符合《污水综合排放标准》(GB 18918-2002)中的三级排放标准。运行成本分析表明,该组合工艺每处理1 m~3垃圾渗滤液的成本大约为36.98元。     

BLR厌氧反应器处理垃圾焚烧厂渗滤液工程运行效能

采用1 100 m3BLR(biogas-lift reactor)厌氧反应器对垃圾焚烧厂渗滤液进行工程化处置,接种污泥为消化污泥,正常运行温度控制在(33±2)℃,启动负荷为1 kg COD/(m3·d),120 d后容积负荷达到10 kg/(m3·d)并稳定运行,出水COD浓度为4 500~6 500 mg/L,COD去除率为88%~92%,出水VFA含量为200~600 mg/L,p H值稳定在7.4~7.7,出水SS含量为1 000 mg/L左右,并可观察到沉降性较好的颗粒化污泥。反应器运行初期将VFA/ALK控制在1.6以内,系统并未因VFA积累而酸化崩溃,运行后期VFA/ALK值小于0.3,系统稳定运行。运行过程中进水氨氮浓度从400 mg/L升高到2 200 mg/L,未发现氨氮对厌氧生物处理的明显抑制现象。垃圾渗滤液中平均每去除1 kg COD产生沼气量为0.32 m3。     

EGSB反应器处理城市生活垃圾沥滤液

采用膨胀颗粒污泥床(EGSB)反应器对城市生活垃圾焚烧厂产生的垃圾沥滤液进行处理。实验结果表明:中温条件下,当COD浓度为55 000 mg/L左右,有机容积负荷(OLR)为22.8 kg COD/(m3.d)时,EGSB对垃圾沥滤液具有较好的的处理效果,COD去除率可达94.2%。当进水COD为72 000 mg/L左右时,为保证反应器的稳定运行,OLR应降低至18.2 kg COD/(m3.d),此时COD去除率可以达到88%左右,出水COD平均为9 103 mg/L。垃圾沥滤液和EGSB处理出水均以小分子量有机物为主,其中<4 kDa的有机物分别占76.5%和74.4%。EGSB对整个分子量区间的溶解性有机物都有较好的处理效果,其中对大分子有机物的处理效率相对更高。     

城市生活垃圾机械生物处理效果

采用机械生物处理工艺研究了淋洗水解、脱水与好氧生物干燥对城市生活垃圾的处理效果.结果表明:在淋洗水解及压榨脱水机械生物处理阶段,控制淋洗液与生活垃圾重量比2∶1,停留时间1.2 ～1.4 d条件下,生活垃圾可以减量49.7％.而过程中产生的淋滤液COD为32 939 mg/L、pH为5.1、COD∶N∶P=261∶5∶3.6,可以进行厌氧消化处理或作为碳源进行资源化利用.在好氧生物干燥阶段,通风量采用0.08 m3/min,2～3d堆体温度可升至73℃,7d左右即可产出LCV高达15 000 kJ/kg左右的高品位垃圾衍生燃料(RDF),其产率为38.2％,氯元素含量低于0.5％,重金属含量较低,满足燃料要求.     

IC厌氧反应器处理垃圾渗滤液

在(35±1)℃条件下,采用IC厌氧反应器对天津大港垃圾焚烧厂垃圾渗滤液进行处理,研究了COD的去除效果、容积负荷、沼气产量和污泥的颗粒化,分析了循环比、上升流速对反应器的影响.结果表明,厌氧反应器经60 d的启动运行后,达到300 m3/d的设计水量,进水容积负荷达到17.7 kg COD/(m3·d),水力停留时间3.7d,COD去除率高于80％,出水挥发酸(VFA)低于l 500 mg/L,平均每去除1 kg COD产沼气0.42 m3,适宜的上升流速和循环比为2.0 ～5.0 m/h、8∶1 ～20∶1.启动结束后,厌氧消化污泥明显出现颗粒化,颗粒污泥的沉降速度达到了67.5 ～ 96.0 m/h,0.3～1.0 mm的颗粒污泥量占有74％.     

ABR-接触氧化-化学氧化组合工艺处理垃圾渗滤液方法研究

以垃圾渗滤液为研究对象,应用ABR 接触氧化 化学氧化组合工艺进行处理。通过分阶段污泥培养驯化以及变容积负荷进行试验研究,试验结果表明:进水有机负荷小于10 kg COD/(m3·d),好氧出水COD稳定在1 000~1 500 mg/L,去除率可以稳定在80%~85%;好氧池出水经过Fenton氧化处理,出水COD小于100 mg/L。该组合工艺对垃圾渗滤液能够进行有效处理,运行效果较好,技术上可行。     

厌氧折流板反应器处理生活污水的运行特性

以厌氧消化污泥作为厌氧折流板反应器ABR的接种污泥,研究恒温(35℃)条件下ABR处理生活污水的启动和运行特性。实验结果表明,ABR反应器仅用了39 d就完成初次启动,COD去除率一直稳定在60%左右。在以后运行的5个阶段里,即当水力停留时间为4~10 h,容积负荷为1.17~2.9 kg COD/m3.d,反应器对COD的平均去除率基本稳定在70.49%~80.2%;并且当HRT=7 h,VRL=1.612 kg COD/m3.d时,反应器对COD的去除率平均高达80.2%,平均COD出水低于100 mg/L。在实验过程中(除启动阶段外),反应器出水碱度均远远大于进水碱度,VFA均在1.5 mmol/L以下。     

UASB处理甲醇废水的实验研究

利用升流式厌氧污泥床(UASB)反应器在中温条件下处理高COD浓度的甲醇废水。当反应器稳定运行,进水COD=36 000 mg/L时,容积负荷可达到70~74 kg COD/(m3.d),COD去除率可以达到95%以上,出水COD2 000 mg/L。通过实验取得的良好实验效果,为利用厌氧技术处理甲醇废水提供了设计依据。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.