Performance of a submerged membrane bioreactor system for biological nutrient removal.

A pilot submerged membrane bioreactor coupled with biological nutrient removal was used to treat the primary effluent at a municipal wastewater treatment plant. Long-term experiments were conducted by varying hydraulic retention time from 6 to 8 hours and solids retention time from 20 to 50 days, respectively. The performance was assessed by monitoring key wastewater parameters, including chemical oxygen demand (COD), nitrogen, and phosphorus concentration in individual anoxic, anaerobic, aerobic, and membrane separation zones. Results showed that the tested system can consistently achieve COD, nitrogen, and phosphorus removal efficiencies at 80 to 98%, 70 to 93%, and 89 to 98%, respectively. Effluent COD remained low as a result of efficient solid retention, even though there was great variation in influent quality. However, total nitrogen increased proportionally with influent concentration. At a 50-day solids retention time, higher COD and nitrogen oxides specific utilization rates in the anoxic zone resulted in a high production of nitrogen oxides in the subsequent aerobic zone.     

Simultaneous nitrification and denitrification of municipal wastewater in aerobic membrane bioreactors.

Simultaneous nitrification-denitrification (SND) of municipal wastewater was investigated in a laboratory-scale membrane bioreactor (MBR) operated at two different hydraulic retention times (HRTs), 0.5 and 1 day, dissolved oxygen 3.0 to 0.5 mg/L, and solids retention time (SRT) between 28 and 120 days. The organic loading rate (OLR) (0.11 to 0.64 kg chemical oxygen demand [COD]/m3/d) and influent soluble COD (SCOD)/ total Kjeldahl nitrogen (TKN) ratio (5 to 19) were varied by the addition of glucose. The ammonia-nitrogen and TKN removals were over 97%, and total nitrogen removal was approximately 89% in the MBR. The maximum specific nitrification rates (98 mg N/d/g VSS) and specific denitrification rates (81 mg N/d/g VSS) occurred at an SCOD/TKN ratio of 9.1. The optimum conditions for maximum total nitrogen removal by SND in a single reactor MBR have been found to be low dissolved oxygen (< 0.6 mg/L) and high OLR (approximately 0.64 kg COD/m3/d) at an HRT of 0.5 day and SRT of approximately 85 days.     

Effects of anaerobic selector hydraulic retention time on biological foam control and enhanced biological phosphorus removal in a pure-oxygen activated sludge system.

Increased anaerobic selector hydraulic retention times (HRTs) in a high-purity oxygen activated sludge process resulted in an increase in soluble orthophosphate release and biodegradable chemical oxygen demand removal, confirming that enhanced biological phosphorus removal occurs at aeration solids retention times (SRTs) below 1.7 days. Under operating conditions that included biological foam trapping and recycling, an anaerobic selector with HRTs higher than 55 minutes resulted in a decrease in filament counts and effective foam control. Effective norcardioform control is achieved through the combination of metabolic selective pressure and increased soluble organic substrate removal in the anaerobic selector and low aeration SRT.     

Simultaneous nitrification and denitrification with anoxic phosphorus uptake in a membrane bioreactor system.

The performance of an innovative membrane bioreactor (MBR) process using anoxic phosphorus uptake with nitrification and denitrification for the treatment of municipal wastewater with respect to operational performance and effluent quality is addressed in this paper. The system was operated at steady-state conditions with a synthetic acetate-based wastewater at a hydraulic retention time (HRT) of 12 hours and on degritted municipal wastewater at a total system HRT of 6 hours. The MBR system was able to achieve 99% biochemical oxygen demand (BOD), chemical oxygen demand (COD), and ammonia-nitrogen (NH4(+)-N); 98% total Kjeldahl nitrogen (TKN); and 97% phosphorus removal, producing effluent BOD, COD, NH4+-N, TKN, nitrate-nitrogen, nitrite-nitrogen, and phosphate-phosphorus of <3, 14, 0.2, 0.26, 5.8, 0.21, and <0.01 mg/L, respectively, at the 6-hour HRT. The comparison of the synthetic and municipal wastewater run is presented in this paper. Steady-state mass balance on municipal wastewater was performed to reveal some key features of the modified MBR system.     

厌氧／缺氧SBR反硝化除磷效能的研究

采用厌氧 缺氧SBR反应器对以硝酸盐作为电子受体的反硝化除磷过程进行了研究。结果表明 ,反硝化聚磷菌完全可以在厌氧 缺氧交替运行条件下得到富集。稳定运行的厌氧 缺氧SBR反应器的反硝化除磷效率 >90 % ,出水磷浓度 <1mg L。进水COD浓度对反硝化除磷的效率影响很大 ,在COD浓度 <180mg L时 ,进水COD浓度越高 ,除磷效率也就越高。较高浓度的进水COD浓度将导致有剩余的COD进入缺氧段 ,对反硝化吸磷构成不利影响。污泥龄为 16d时 ,厌氧 缺氧SBR反应器取得稳定和理想的反硝化除磷效果。污泥龄减少到 8d ,由于反硝化聚磷菌的流失导致反硝化除磷效率的下降。当污泥龄恢复到 16d时 ,经过一段时间的运行 ,反硝化聚磷菌重新得到富集 ,除磷效率恢复到 90 %以上。     

Simultaneous carbon, nitrogen and phosphorous removal from municipal wastewater in a circulating fluidized bed bioreactor

In this study, the performance of the circulating fluidized bed bioreactor (CFBB) with anoxic and aerobic beds and employing lava rock as a carrier media for the simultaneous removal of carbon, nitrogen and phosphorus from municipal wastewater at an empty bed contact time (EBCT) of 0.82 h was discussed. The CFBB was operated without and with bioparticles' recirculation between the anoxic and aerobic bed for 260 and 110 d respectively. Without particles' recirculation, the CFBB was able to achieve carbon (C), total nitrogen (N) and phosphorous (P) removal efficiencies of 94%, 80% and 65% respectively, whereas with bioparticles' recirculation, 91%, 78% and 85% removals of C, N and P were achieved. The CFBB was operated at long sludge retention time (SRT) of 45-50 d, and achieved a sludge yield of 0.12-0.135 g VSS g COD(-1). A dynamic stress study of the CFBB was carried out at varying feed flow rates and influent ammonia concentrations to determine response to shock loadings. The CFBB responded favourably in terms of TSS and COD removal to quadrupling of the feed flow rate. However, nitrification was more sensitive to hydraulic shock loadings than to doubling of influent nitrogen loading.     

Behaviors of intercellular materials and nutrients in biological nutrient removal process supplied with domestic wastewater and food waste.

A four-stage biological nutrient removal (BNR) process was operated to investigate the effect of anaerobically fermented leachate of food waste (AFLFW) as an external carbon source on nutrient removal from domestic wastewater having a low carbon-to-nitrogen ratio. The BNR system that was supplemented with AFLFW showed a good performance at a sludge retention time (SRT) of 30 days, despite low temperature. With this wastewater, average removal efficiencies of soluble chemical oxygen demand (COD), total nitrogen (T-N), and total phosphorus (T-P) were 88 to 93%, 70 to 74%, and 63 to 68%, respectively. In this study, several kinds of poly-hydroxyalkanoates (PHAs) were observed in cells. These included 24% poly-3-hydroxybutyrate (PHB), 41% poly-3-hydroxyvalerate (PHV), 18% poly-3-hydroxyhexanoate (PHH), 10% poly-3-hydroxyoctanoate (PHO), 5% poly-3-hydroxydecanoate (PHD). and 2% poly-3-hydroxydodecanoate (PHDD), indicating that microorganisms could store various PHAs through the different metabolic pathways. However, breakdown of the enhanced biological phosphorus removal (EBPR) mechanism was observed when SRT increased from 30 to 50 days for the enhancement of nitrification. To study the effect of SRT on EBPR, a sequencing batch reactor (SBR) system that was supplied with glucose was operated at various SRTs of 5, 10, and 15 days. Nitrification and denitrification efficiencies increased as SRT increased. However, the content of intracellular materials such as PHAs, glycogen. and poly-P in cells decreased. From these results, it was concluded that SRT should be carefully controlled to increase nitrification activity and to maintain biological phosphorus removal activity in the BNR process.     

Biological treatment of a synthetic gold milling effluent

This paper reports on biological sludge acclimatisation and the results concerning the removal of free cyanide, thiocyanate and metallocyanides (copper, iron and zinc) from a synthetic gold milling effluent. The experiments were carried out in a continuous bench-scale bioreactor, and the experimental set-up consisted of two identical units, one of which served as control. The acclimatisation of the biomass was based on a stepwise procedure, in which the proportion of synthetic solution in the influent was gradually increased. The reactors were fed with a mixture of synthetic effluent and sewage, and the treatment efficiency was evaluated through the monitoring of the following parameters: chemical oxygen demand (COD), free cyanide, thiocyanate, copper, iron and zinc concentrations. A well adapted microbial consortium was obtained at the end of the acclimatisation period, which was able to remove more than 95% of free cyanide, thiocyanate, copper and zinc, originally found in the influent. These removal efficiencies were obtained when the reactor was operated with a hydraulic retention time (HRT) of about 8 h. The performance results of experiments carried out with lower HRT (5 h) and higher dissolved oxygen (DO) concentration (6.5 mg litre(-1)) are also presented and discussed in this study.     

水力停留时间对膜生物反应器复合工艺污水处理特性的影响

开发了厌氧-多级好氧/缺氧-膜生物反应器复合工艺,在不同水力停留时间(HRT)下,考察了系统对污染物去除效果及其膜污染的特性.结果表明,在试验选定的HRT范围内,系统对TN和TP的去除率随着HRT的降低而升高,当HRT为8.70、6.96、4.97 h时,系统对TN和TP的平均去除率分别为73.15%、79.76%、81.98%和67.79%、80.99%、92.16%.但是,较低HRT条件下膜通量较高,会加剧膜污染进程.解决这一问题的措施是增加膜组件个数,从而在不提高膜通量的情况下使系统保持较低的HRT,保证系统高效稳定的污染物去除效果.     

Aerobic and anaerobic membrane bioreactors for municipal wastewater treatment.

An aerobic bioreactor and an anaerobic bioreactor, each coupled with a microfiltration membrane filter (MBR), were operated at different hydraulic retention times (HRTs) with primary effluent from the City of Elmhurst, Illinois, municipal-wastewater-treatment plant. The soluble chemical oxygen demand (COD) removal performance of the anaerobic MBR system was similar to that of the aerobic MBR under the same operational conditions, without the added cost of aeration. The results indicated that the solids deposition rate on the membrane surface was lower in the case of anaerobic MBR compared to the aerobic MBR, indicating possible lower loss in water-flux rates. This research found that an anaerobic MBR is a feasible and economical option for municipal-wastewater-treatment plants seeking COD removal by a biological process followed by a separate nitrification and denitrification system.     

Characterizing the passage of personal care products through wastewater treatment processes.

Wastewater treatment facilities use secondary treatment to stabilize the effect of discharged effluent on receiving waters by oxidizing biodegradable organic matter and reducing suspended solids and nutrients. The process was never specifically intended to remove trace quantities of xenobiotics, such as endocrine-disrupting compounds (EDCs) and pharmaceuticals and personal care products (PPCPs). Nevertheless, European studies performed at bench-scale or at small facilities have demonstrated that a critical minimum solids retention time (SRT) can achieve good reduction of many EDCs and pharmaceuticals. The objective of this study was to expand these findings to the removal performance for 20 PPCPs commonly found in the influent to full-scale facilities operating in the United States. The participating plants use SRT conditions ranging from 0.5 to 30 days and include facility capacities ranging from 19 000 m3/d (5 mgd) to greater than 1 136 000 m3/d (300 mgd). Two pilot membrane bioreactors were also included in the study. The 20 PPCPs were categorized into nine bin combinations of occurrence frequency and treatment reduction performance. While most compounds were well removed, galaxolide (a musk fragrance) occurred frequently and was resistant to removal. A minimum critical SRT, defined as the minimum SRT, needed to consistently demonstrate greater than 80% removal (SRT80), was compound-dependent, with most compounds removed at 5 to 15 days and a small group requiring longer SRTs. From limited data, no additional removal could be attributed to the use of membrane bioreactors, media filters, or longer hydraulic retention times. Reverse osmosis was effective in removing any remaining compounds.     

Comparison of nitrification rates in conventional and membrane-assisted biological nutrient removal processes

A membrane-assisted and a conventional activated sludge system, both operated in an enhanced biological phosphorus removal (EBPR) mode and under identical operating conditions, were studied to investigate the effect of the membrane solids-liquid separation on nitrification activity. Both the membrane EBPR (MEBPR) and conventional EBPR (CEBPR) processes achieved stable and complete removal of ammonium-nitrogen from the influent wastewater. However, when the intrinsic nitrification activity was assessed in offline batch tests, the CEBPR mixed liquor exhibited 15 to 75% greater nitrification potential than the MEBPR counterpart. These results were further validated by monitoring nitrification rates of conventional mixed liquor as it evolved toward a membrane mixed liquor. It was also demonstrated that the larger aerobic mass fraction of the MEBPR system could not be the only factor influencing the reduced intrinsic nitrification rate. The present study strongly suggests that the presence of a membrane solids-liquid separation per se may be sufficient to alter the nitrification kinetics of an EBPR mixed liquor and that this possibility should be considered in arriving at an appropriate process design.     

Effects of reduced return activated sludge flows and volume on anaerobic zone performance for a septic wastewater biological phosphorus removal system.

Enhanced biological phosphorous removal (EBPR) performance was found to be adequate with reduced return-activated sludge (RAS) flows (50% of available RAS) to the anaerobic tank and smaller-than-typical anaerobic zone volume (1.08 hours hydraulic retention time [HRT]). Three identical parallel biological nutrient removal pilot plants were fed with strong, highly fermented (160 mg/L volatile fatty acids [VFAs]), domestic and industrial wastewater from a full-scale wastewater treatment facility. The pilot plants were operated at 100, 50, 40, and 25% RAS (percent of available RAS) flows to the anaerobic tank, with the remaining RAS to the anoxic tank. In addition, varying anaerobic HRT (1.08 and 1.5 hours) and increased hydraulic loading (35% increase) were examined. The study was divided into four phases, and the effect of these process variations on EBPR were studied by having one different variable between two identical systems. The most significant conclusion was that returning part of the RAS to the anaerobic zone did not decrease EBPR performance; instead, it changed the location of phosphorous release and uptake. Bringing less RAS to the anaerobic and more to the anoxic tank decreased anaerobic phosphorus release and increased anoxic phosphorus release (or decreased anoxic phosphorus uptake). Equally important is that, with VFA-rich influent wastewater, excessive anaerobic volume was shown to hurt overall phosphorus removal, even when it resulted in increased anaerobic phosphorus release.     

Simultaneous nitrification-denitrification and clarification in a pseudoliquified activated sludge system.

This paper describes results from a pilot study of a novel wastewater treatment technology, which incorporates nutrient removal and solids separation to a single step. The pseudoliquified activated sludge process pilot system was tested on grit removal effluent at flowrates of 29.4 to 54.7 m3/d, three different solid residence times (SRT) (15, 37, and 57 days), and over a temperature range of 12 to 28 degrees C. Despite wide fluctuations in the influent characteristics, the system performed reliably and consistently with respect to organics and total suspended solids (TSS) removals, achieving biochemical oxygen demand (BOD) and TSS reductions of > 96% and approximately 90%, respectively, with BOD5 and TSS concentrations as low as 3 mg/L. Although the system achieved average effluent ammonia concentrations of 2.7 to 3.2 mg/L, nitrification efficiency appeared to be hampered at low temperatures (< 15 degrees C). The system achieved tertiary effluent quality with denitrification efficiencies of 90 and 91% total nitrogen removal efficiency at a total hydraulic retention time of 4.8 hours and an SRT of 12 to 17 days. With ferric chloride addition, effluent phosphorous concentrations of 0.5 to 0.8 mg/L were achieved. Furthermore, because of operation at high biomass concentrations and relatively long biological SRTs, sludge yields were over 50% below typical values for activated sludge plants. The process was modeled using activated sludge model No. 2, as a two-stage system comprised an aerobic activated sludge system followed by an anoxic system. Model predictions for soluble BOD, ammonia, nitrates, and orthophosphates agreed well with experimental data.     

Removal of organic and nitrogen and molecular weight distribution of residual soluble organic from entrapped mixed microbial cells and activated sludge processes.

The simultaneous removal of organic and nitrogen and molecular weight distribution (MWD) of residual soluble chemical oxygen demand (RSCOD) in final effluent were investigated using entrapped mixed microbial cells (EMMC) and conventional activated sludge processes. Two different types of processes using EMMC carriers demonstrated better organic and nitrogen removal performance because of the high solids retention time (SRT) compared with the activated sludge process. Regarding the RSCOD, the longer SRT process (EMMC) was affected by reducing the hydraulic retention time, resulting in the increase of high-molecular-weight materials. On the other hand, reducing the aeration period had significantly affected the MWD in the shorter SRT process (activated sludge), resulting in an increase of low-molecular-weight materials.     

生物膜反应器连续处理餐饮废水

用生物膜反应器连续处理餐水能有效降低废水中的ＢＯＤ及ＣＯＤ浓度。研究了水力停留时间对有机物去除率的影响,结果表明当水力停留时间大于７．８ｈ时,废水的ＣＯＤ,ＢＯＤ及ＴＳＳ的去除率均高于９０％。实验操作时,水力停留时间应略大于５．７ｈ。     

改良型一体化氧化沟工艺在低碳源条件下脱氮除磷

针对在低碳源条件下脱氮除磷效果不佳,将倒置A2/O工艺的思想运用于一体化氧化沟工艺中,构建一种新型污水处理系统,即改良型一体化氧化沟工艺。实验考查了系统在低碳源条件下的脱氮除磷能力;结果表明:当缺氧区进水分配比r=0.8,泥龄SRT=10 d,好氧区水力停留时间HRT=12 h时,该系统对COD、NH4+-N和TP的去除率分别达70.8%、89.3%和72.1%,出水NOx--N为1.65 mg/L,同时处理效果稳定,出水水质达到了《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级B标准的要求。     

Removal of organic compounds during treating printing and dyeing wastewater of different process units

Wastewater in Shaoxing wastewater treatment plant (SWWTP) is composed of more than 90% dyeing and printing wastewater with high pH and sulfate. Through a combination process of anaerobic acidogenic [hydraulic retention time (HRT) of 15h], aerobic (HRT of 20h) and flocculation-precipitation, the total COD removal efficiency was up to 91%. But COD removal efficiency in anaerobic acidogenic unit was only 4%. As a comparison, the COD removal efficiency was up to 35% in the pilot-scale upflow anaerobic sludge bed (UASB) reactor (HRT of 15h). GC-MS analysis showed that the response abundance of these wastewater samples decreased with their removal of COD. A main component of the raw influent was long-chain n-alkanes. The final effluent of SWWTP had only four types of alkanes. After anaerobic unit at SWWTP, the mass percentage of total alkanes to total organic compounds was slightly decreased while its categories increased. But in the UASB, alkanes categories could be removed by 75%. Caffeine as a chemical marker could be detected only in the effluent of the aerobic process. Quantitative analysis was given. These results demonstrated that GC-MS analysis could provide an insight to the measurement of organic compounds removal.     

改良型A2／O-MBR工艺的反硝化除磷性能研究

重点考察了-种改良型膜生物反应器（A2／O—MBR）的脱氮除磷性能。该工艺主要特点在于对膜池硝化回流液进行了固液分离，并将上清液和浓缩污泥分别回流至缺氧池和厌氧池，这种改进提高了系统对氮、磷的同步去除效率。实验结果表明，在水力停留时间（HRT）为12h，污泥龄（SRT）为30d，混合液回流比为200％的运行条件下，进水COD、NH4＋-N、TN和TP平均浓度分别为（225±38）、（24．8±3．9）、（26．7±2．9）和（2．90±0．53）mg／L时，增加膜池硝化回流液固液分离装置前后，系统对COD和NH4＋-N的去除都维持在较高水平，而系统对TN和TP的去除效果显著提高，出水TN和TP平均浓度分别由（14．9±3．3）mg／L和（1．95±0．72）mg／L下降到（9．4±1．9）mg／L和（0．91±0．38）mg／L，表明增加膜池硝化回流液固液分离装置显著改善了A2／O-MBR系统的脱氮除磷效果。反硝化除磷活性实验结果进一步表明，改进后系统中反硝化除磷活性占总除磷活性的比例由51．5％上升至61．7％，说明增加膜池硝化回流液固液分离装置强化了系统的反硝化除磷性能。     

曝气生物滤池处理农村污水的中试研究

采用研制的曝气生物滤池对农村污水进行处理，研究其性能特点和影响因素。结果表明：在气水比为5∶1，水力停留时间（HRT）为15 h，进水COD浓度在250 mg/L以下时，COD和氨氮的去除率分别在80％和90％以上，出水COD和氨氮值达到国家《城镇污水处理厂污染物排放标准》一级A标准；反应器在冬季水温12℃以上运行时出水COD和氨氮值比在夏季运行时有所上升，但去除率仍在80%和90%以上，可以达到排放标准。