RuO2/La2O3/TiO2悬浮体系中直接耐晒黑G的光催化降解

钛酸丁酯为前驱体,采用溶胶-凝胶-浸渍法制备RuO2/La2O3/TiO2复合光催化剂,以紫外灯为光源,研究了催化剂组成、煅烧温度、溶液pH值等因素对直接耐晒黑G(DFBG)光催化降解的影响.结果表明掺杂量w(La2O3)1.39%、w(RuO2)0.12%、煅烧温度500℃(2 h)、溶液pH值7.3时,光催化活性最佳.当通气量为200 mL/min,催化剂投加量为150mg时,50 mg/L的DFBG溶液经60 min降解,其降解率近100%.DFBG的光催化降解服从Langmuir-Hinshelwood动力学模型,测得相应的动力学参数k=7.42×10-3mmol/L·min,K=19.54 L/mmol.     

TiO2/CdS复合半导体光催化剂降解甲基橙的实验研究

采用Sol-Gel法制备TiO2/CdS复合半导体光催化剂,以8 W-365 nm的紫外灯为光源、甲基橙溶液模拟染料废水、在自制的光催化反应器中研究TiO2/CdS的光催化活性和光催化降解甲基橙的特点和规律.结果表明,当CdS掺入量为0.5%(摩尔比)时,TiO2/CdS的光催化活性最高;当CdS的掺入量＞3.5%(摩尔比)时,TiO2/CdS光催化剂的光催化活性低于TiO2的光催化活性;对初始浓度为15 mg/L的甲基橙溶液处理2.5 h后,脱色率可达44%;甲基橙的光催化降解反应符合Y=A B1×X B2×X2动力学模型.     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La2O3/ZnO/TiO2复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La2O3/ZnO/TiO2的光催化性能.结果表明:当锌和镧的掺杂量w(zno)=20%,w(La2O3)=0.5%,煅烧温度为500℃时,La2O3/ZnO/TiO2复合光催化剂的光催化活件最高;当催化荆投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La2O3/ZnO/TiO2对活性艳红K-2BP的降解效果最好.实验证明.La2O3/ZnO/TiO2对活性艳红K-2BP的降解遵从Lang-muir-Hinshelwood动力学模型,测得其反应速率常数k=11.5 mg/(L·min);吸附常数K=2.88×10-2L/mg.     

负载型纳米复合半导体WO_3-TiO_2/AC光催化降解刚果红废水

采用溶胶-凝胶-浸渍-焙烧法制备了负载型纳米复合半导体WO3-TiO2/AC光催化剂,以偶氮染料刚果红为目标降解物,通过正交实验优化了刚果红废水的降解条件,并对其光催化动力学进行了探讨.结果表明,刚果红废水的最佳降解条件为:催化剂投加量10 g/L,pH=7,H2O2用量为3.5 mL/L.在最佳条件下,当刚果红废水起始浓度为40 mg/L时,反应120 min后,刚果红溶液的去除率可达95.21%,较相同条件下TiO2/AC对刚果红染料的降解率提高了19.57%.光催化剂对刚果红的光催化降解符合Langmuir-Hinshelwood(L-H)模型.     

漂浮型可见光催化剂Fe-N-TiO_2/FP-CTS的制备及其对溶解性柴油的降解

以漂珠为载体,用壳聚糖对漂珠进行改性,并采用溶胶凝胶法,制备了Fe-N共掺杂改性TiO2的漂浮型可见光催化剂(Fe-N-TiO2/FP-CTS),使用X射线衍射(XRD)、紫外可见分光光谱(UV-Vis)、N2吸附-脱附(BET)和扫描电子显微镜(SEM)等分析进行表征。研究结果表明,用壳聚糖改性漂珠可以增加复合光催化剂的比表面积和孔容;相较于N-掺杂TiO2/FP复合光催化剂,Fe-N共掺杂更能促进对复合光催化剂可见光的吸收;光催化4 h后,Fe-N-TiO2/FP-CTS对溶解性柴油的降解率达到61.7%,明显优于Fe-N-TiO2/FP和N-TiO2/FP。当初始pH=5,柴油乳化剂浓度=120 mg/L时,复合光催化剂对溶解性柴油的光催化降解效果最佳。     

掺杂负载型纳米TiO2降解橙黄G的光催化活性及其动力学研究

采用溶胶-凝胶法和浸渍-焙烧法制备了掺杂Sn(Ⅳ)的TiO2/AC光催化剂,以偶氮染料橙黄G为目标降解物,对光催化反应条件进行了优化.结果表明:利用Sn(Ⅳ)掺杂量为2.5 at.%的TiO2/AC光催化剂,在进水浓度50 mg/L,催化剂的用量12.5 g/L,pH值2.0,H2O21.5 mL/L,主波长为365 nm的300W高压汞灯光照条件下,反应60 min,橙黄G的光催化去除率可达99.1%.该反应符合Langmuir-Hinshelwood动力学方程,其速控步为吸附反应.共存阴离子SO42-和H2PO4-,对橙黄G的光催化降解反应均有一定的抑制作用.     

Fe~(3+)掺杂TiO_2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe3+掺杂TiO2/凹凸棒(Fe3+-TiO2/ATP)复合光催化剂材料。在可见光条件下,以亚甲基蓝(MB)溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe3+掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计(L25(53))优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood(L-H)动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe3+掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10-3min-1,反应4 h后MB的降解率(Dt)可达75.88%,相同实验条件下与P25(1.51×10-3min-1)相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。     

Pd/N共掺杂TiO_2的制备及其光催化降解苯酚的研究

将纳米管钛酸浸入含尿素和金属(Pd)硝酸盐的乙醇溶液中,乙醇超声挥发后所得样品先在空气气氛、600℃下煅烧,再在H2气氛、400℃下热还原制备得到Pd/N共掺杂TiO2光催化剂(Pd/N-TiO2)。利用光电子能谱(XPS)仪研究了催化剂表面N、Pd元素的化学态。结果表明,N元素以Ti—O—N形式存在,Pd元素以单质金属状态存在。考察了Pd/N-TiO2的紫外光光催化降解苯酚的活性,与单纯TiO2光催化剂和N掺杂TiO2光催化剂相比,Pd/N-TiO2活性明显提高。研究了催化剂用量、苯酚初始浓度和pH、O2流量以及外加双氧水等条件对紫外光光催化降解苯酚的活性的影响,得到光催化降解苯酚的最佳工艺条件:苯酚初始质量浓度为120mg/L,催化剂用量为0.10g/L,苯酚溶液初始pH为8,O2流量为80mL/min,加入适量双氧水。     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

TiO_2/AC复合催化剂的制备及其对六氯苯的光催化降解性能研究

以颗粒活性炭（AC）和钛酸丁酯为原料,采用微波辐射法制备TiO2/AC复合光催化剂,并对制备的催化剂进行了表征;采用该催化剂对六氯苯进行光催化降解,确定了六氯苯降解的最佳工艺条件,并就几种外加试剂对TiO2/AC光催化降解六氯苯的强化作用进行了探讨。结果表明,制备的催化剂中TiO2均匀分布在活性炭表面、呈单一的锐钛矿晶型,晶粒生长完善。该催化剂催化降解六氯苯的最佳工艺条件为：pH值为5、TiO2负载量为18.2%、TiO2/AC投加量为0.4 g/L、反应时间为60 min。在此条件下,六氯苯降解效率达90.3%。添加适量的H2O2、AgNO3、K2S2O8、KIO4和KMnO4均能提高TiO2/活性炭对六氯苯的光催化降解效率。5种外加试剂的适宜添加量分别为0.3%、1.0、1.0、0.1和0.1 mmol/L,对TiO2/AC光催化效率的强化作用大小顺序为：H2O2〉AgNO3〉K2S2O8〉KMnO4〉KIO4。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.