developing a practical dispersion model for an air quality region

A series of computer models have been developed to predict air quality in the New York/New Jersey/Connecticut Air Quality Region. Efforts have been directed at models which have a shorter time scale than climatological models, and which are capable of providing better recommendations for effective abatement and planning, but use input data presently available.

The basic dispersion model for these investigations is a steady-state,nondivergent Gaussian-type model. A modified inventory of SO₂ sources,based on published data for the New York/New Jersey/Connecticut Air Quality Region, was prepared for use with the model. The basic model has been subjected to various internal sensitivity analyses, in which was isolated the variation produced in the pollutant concentration by a given change in each of the factors that contribute, e.g., wind speed, wind direction,mixing depth, stability conditions, source strengths, and grid size for the area sources.

To date, validation tests of the model have been made against the July and August 1969 data for the ten telemetering stations of the New York City Aerometric Network. Hourly as well as averaged concentrations were considered. Various sets of meteorological data from the network stations and the three area airports, were compared and tested. Additional tests, particularly for the winter season, are needed to substantiate the preliminary conclusions suggested by the results to date.

Considerable insight into the relative importance of model components has been acquired from the sensitivity studies. Furthermore the validation results lend support to the belief that a reasonably simple, practical dispersion model can be developed for the region.     

Simulation of the Environmental Impact of an Airport on the Surrounding Air Quality

It is the purpose of this study to demonstrate the procedure involved in simulating those average and maximum pollutant concentrations at or around an airport which fall under the control of the Clean Air Act. The information is useful, when planning new or expanding existing airports, when estimating the impact of airports on the surrounding air quality, and when assessing the effectiveness of control procedures. Simulation of airport air quality requires the accurate assessment of the temporal and spatial emission patterns. This involves the tabulation of air traffic density by type and engine, make and model of aircraft, and engine mode number; the use of fuel by different aircraft; the pollutant emission rates by engine model and operational mode; the allocation of emission rates to the respective runways, turn-off points, taxi-ways, and parking areas, and the time each aircraft spent in the different operational modes. The resulting emission pattern for the Honolulu International Airport reflects scheduled and unscheduled commercial and military jet and piston aircraft and nonaircraft operations. Using this and the appropriate meteorological information average and maximum surface concentrations were calculated and compared with local ambient air quality standards. The calculation of concentrations is based on a newly developed diffusion model incorporating harmonic mean wind speeds for every degree of wind direction as determined by a Parzen maximum likelihood interpolation technique, and the assumption of log-normal concentration distributions. It is shown that for some pollutants the air quality standards are substantially exceeded, and it is concluded that airports may have a considerable adverse impact on their surrounding air quality.     

A Comparative Validation of the RAM and PTMTP Models for Short-Term SO2 Concentrations in Two Urban Areas

A comprehensive and comparative model validation of two EPA models for short-term SO₂ concentrations was performed. The two models tested were RAM (Urban version) and PTMTP (Terrain version). Both are multiple source, multiple receptor gaussian plume models, recommended in the EPA Guideline On Air Quality Models. ¹ The principal difference between the two models is in their use of empirical dispersion coefficients. It was because of the potential for markedly different predicted maximum SO₂ concentrations, and the absence of any testing data on the RAM model, that the validation analysis was undertaken. The current study utilized a full year of air quality data from monitoring sites in two Indiana cities, Michigan City and Indianapolis. Cumulative frequency distributions for each site and model were prepared and comparisons made. The results indicate that the RAM (Urban) model was highly inaccurate in predicting maximum short-term SO₂ concentrations. The PTMTP model, although conservative in its estimates, produces results which more closely resemble the distribution of observed SO₂ concentrations. The body of information presented in this paper is directed to environmental scientists responsible for air quality modeling, and to those persons who set policy on the use of models in air quality studies.     

The air quality forecast rote: Recent changes and future challenges

Air quality forecasting is a recent development, with most programs initiated only in the last 20 years. During the last decade, forecast preparation procedure—the forecast rote—has changed dramatically. This paper summarizes the unique challenges posed by air quality forecasting, details the current forecast rote, and analyzes prospects for future improvements. Because air quality forecasts must diagnose and predict several pollutants and their precursors in addition to standard meteorological variables, it is, compared with weather forecasts, a higher-uncertainty forecast. Forecasters seek to contain the uncertainty by “anchoring” the forecast, using an a priori field, and then “adjusting” the forecast using additional information. The air quality a priori, or first guess, field is a blend of past, current, and near-term future observations of the pollutants of interest, on both local and regional scales, and is typically coupled with predicted air parcel trajectories. Until recently, statistical methods, based on long-term training data sets, were used to adjust the first guess. However, reductions in precursor emissions in the United States, beginning in the late 1990s and continuing to the present, eroded the stationarity assumption for the training data sets and degraded forecast skill. Beginning in the mid-2000s, output from modified numerical air quality prediction (NAQP) models, originally developed to test pollution control strategies, became available in near real time for forecast support. The current adjustment process begins with the analyses and postprocessing of individual NAQP models and their ad hoc ensembles, often in concert with new statistical techniques. The final adjustment step uses forecaster expertise to assess the impact of mesoscale features not resolved by the NAQP models. It is expected that advances in model resolution, chemical data assimilation, and the formulation of emissions fields will improve mesoscale predictions by NAQP models and drive future changes in the forecast rote.

Implications: Routine air quality forecasts are now issued for nearly all the major U.S. metropolitan areas. Methods of forecast preparation—the forecast rote—have changed significantly in the last decade. Numerical air quality models have matured and are now an indispensable part of the forecasting process. All forecasting methods, particularly statistically based models, must be continually calibrated to account for ongoing local- and regional-scale emission reductions.     

Future Impacts of Distributed Power Generation on Ambient Ozone and Particulate Matter Concentrations in the San Joaquin Valley of California

ABSTRACT

Distributed power generation—electricity generation that is produced by many small stationary power generators distributed throughout an urban air basin—has the potential to supply a significant portion of electricity in future years. As a result, distributed generation may lead to increased pollutant emissions within an urban air basin, which could adversely affect air quality. However, the use of combined heating and power with distributed generation may reduce the energy consumption for space heating and air conditioning, resulting in a net decrease of pollutant and greenhouse gas emissions. This work used a systematic approach based on land-use geographical information system data to determine the spatial and temporal distribution of distributed generation emissions in the San Joaquin Valley Air Basin of California and simulated the potential air quality impacts using state-of-the-art three-dimensional computer models. The evaluation of the potential market penetration of distributed generation focuses on the year 2023. In general, the air quality impacts of distributed generation were found to be small due to the restrictive 2007 California Air Resources Board air emission standards applied to all distributed generation units and due to the use of combined heating and power. Results suggest that if distributed generation units were allowed to emit at the current Best Available Control Technology standards (which are less restrictive than the 2007 California Air Resources Board standards), air quality impacts of distributed generation could compromise compliance with the federal 8-hr average ozone standard in the region.

IMPLICATIONS The San Joaquin Valley is a fast growing region that demands increasing power generation to sustain the economic development, and at the same time it is one of the worst polluted areas in the United States. Hence, the region demands alternatives that minimize the air quality impacts of power generation. This paper addresses the air quality impacts of distributed generation of power, an alternative to central power generation that can potentially reduce greenhouse gas and pollutant emissions throughout the United States.     

A System for Abatement Control Strategy Evaluation

The Air Quality Control Program of the Commonwealth of Massachusetts has developed an implementation plan for the Metropolitan Boston Intrastate Air Quality Control Region as required by PL 90-148. An essential part of the plan was a set of control regulations designed to achieve and maintain an air quality compatible with adopted standards. Control strategy modeling was used as a tool in selecting the most appropriate regulations to achieve this goal. The body of information presented in this paper is directed to those state and county air pollution control officials concerned with the formulation and evaluation of regulations.

The paper details the procedures developed and presents a case history of their use in the region. The system is a synthesis of generally-available software and newly-developed computer programs to provide ahighly automated computational structure. It permits rapid simulation of the emissions resulting from the application of various control regulations. Predictions on the changes expected in ambient air quality levels are then made by the use of the Air Quality Display Model (AQDM).

The initial step in the application was a calibration of the system using predicted and measured annual concentrations. This step yielded correlation coefficients of 0.92 for sulfur dioxide and 0.85 for particulates. Subsequently, the system was used to evaluate the baseline case of uncontrolled sulfur in fuel use. Alternative sulfur control strategies were tested for compatibility with air quality standards. The principal strategies tested were: (a) 1% sulfur uniformly throughout the region; (6) 1% sulfur in core area of region, 2.2% sulfur elsewhere; (c) 0.5% sulfur in core area of region, 2.2% sulfur elsewhere; (d) 0.5% sulfur in core area of region, 1.0% sulfur elsewhere.

Strategies (b) and (d) were implemented into a time phased set of control regulations for the region.

Experience with the system has shown it to be a convenient and rapid method for simulating the effects of control regulations. Furthermore, the utility of this initial model warrants expansion of its application to the other air quality control regions in the Commonwealth.     

Conjunctive Use of Models to Design Cost-Effective Ozone Control Strategies

Abstract

The management of tropospheric ozone (O₃) is particularly difficult. The formulation of emission control strategies requires considerable information including: (1) emission inventories, (2) available control technologies, (3) meteorological data for critical design episodes, and (4) computer models that simulate atmospheric transport and chemistry. The simultaneous consideration of this information during control strategy design can be exceedingly difficult for a decision-maker. Traditional management approaches do not explicitly address cost minimization. This study presents a new approach for designing air quality management strategies; a simple air quality model is used conjunctively with a complex air quality model to obtain low-cost management strategies. A simple air quality model is used to identify potentially good solutions, and two heuristic methods are used to identify cost-effective control strategies using only a small number of simple air quality model simulations. Subsequently, the resulting strategies are verified and refined using a complex air quality model. The use of this approach may greatly reduce the number of complex air quality model runs that are required. An important component of this heuristic design framework is the use of the simple air quality model as a screening and exploratory tool. To achieve similar results with the simple and complex air quality models, it may be necessary to “tweak” or calibrate the simple model. A genetic algorithm-based optimization procedure is used to automate this tweaking process. These methods are demonstrated to be computationally practical using two realistic case studies, which are based on data from a metropolitan region in the United States.     

Increasing the Use of Earth Science Data and Models in Air Quality Management

In 2010, the U.S. National Aeronautics and Space Administration (NASA) initiated the Air Quality Applied Science Team (AQAST) as a 5-year, $17.5-million award with 19 principal investigators. AQAST aims to increase the use of Earth science products in air quality-related research and to help meet air quality managers’ information needs. We conducted a Web-based survey and a limited number of follow-up interviews to investigate federal, state, tribal, and local air quality managers’ perspectives on usefulness of Earth science data and models, and on the impact AQAST has had. The air quality managers we surveyed identified meeting the National Ambient Air Quality Standards for ozone and particulate matter, emissions from mobile sources, and interstate air pollution transport as top challenges in need of improved information. Most survey respondents viewed inadequate coverage or frequency of satellite observations, data uncertainty, and lack of staff time or resources as barriers to increased use of satellite data by their organizations. Managers who have been involved with AQAST indicated that the program has helped build awareness of NASA Earth science products, and assisted their organizations with retrieval and interpretation of satellite data and with application of global chemistry and climate models. AQAST has also helped build a network between researchers and air quality managers with potential for further collaborations.

Implications: NASA’s Air Quality Applied Science Team (AQAST) aims to increase the use of satellite data and global chemistry and climate models for air quality management purposes, by supporting research and tool development projects of interest to both groups. Our survey and interviews of air quality managers indicate they found value in many AQAST projects and particularly appreciated the connections to the research community that the program facilitated. Managers expressed interest in receiving continued support for their organizations’ use of satellite data, including assistance in retrieving and interpreting data from future geostationary platforms meant to provide more frequent coverage for air quality and other applications.     

Development and implementation of a remote-sensing and in situ data-assimilating version of CMAQ for operational PM2.5 forecasting. Part 1: MODIS aerosol optical depth (AOD) data-assimilation design and testing

This two-part paper reports on the development, implementation, and improvement of a version of the Community Multi-Scale Air Quality (CMAQ) model that assimilates real-time remotely-sensed aerosol optical depth (AOD) information and ground-based PM_2.5 monitor data in routine prognostic application. The model is being used by operational air quality forecasters to help guide their daily issuance of state or local-agency-based air quality alerts (e.g. action days, health advisories). Part 1 describes the development and testing of the initial assimilation capability, which was implemented offline in partnership with NASA and the Visibility Improvement State and Tribal Association of the Southeast (VISTAS) Regional Planning Organization (RPO). In the initial effort, MODIS-derived aerosol optical depth (AOD) data are input into a variational data-assimilation scheme using both the traditional Dark Target and relatively new “Deep Blue” retrieval methods. Evaluation of the developmental offline version, reported in Part 1 here, showed sufficient promise to implement the capability within the online, prognostic operational model described in Part 2. In Part 2, the addition of real-time surface PM_2.5 monitoring data to improve the assimilation and an initial evaluation of the prognostic modeling system across the continental United States (CONUS) is presented.

Implications: Air quality forecasts are now routinely used to understand when air pollution may reach unhealthy levels. For the first time, an operational air quality forecast model that includes the assimilation of remotely-sensed aerosol optical depth and ground based PM_2.5 observations is being used. The assimilation enables quantifiable improvements in model forecast skill, which improves confidence in the accuracy of the officially-issued forecasts. This helps air quality stakeholders be more effective in taking mitigating actions (reducing power consumption, ride-sharing, etc.) and avoiding exposures that could otherwise result in more serious air quality episodes or more deleterious health effects.     

Source apportionment of particulate matter (PM2.5) in an urban area using dispersion,receptor and inverse modelling

Air pollution emission inventories are the basis for air quality assessment and management strategies. The quality of the inventories is of great importance since these data are essential for air pollution impact assessments using dispersion models. In this study, the quality of the emission inventory for fine particulates (PM_2.5) is assessed: first, using the calculated source contributions from a receptor model; second, using source apportionment from a dispersion model; and third, by applying a simple inverse modelling technique which utilises multiple linear regression of the dispersion model source contributions together with the observed PM_2.5 concentrations. For the receptor modelling the chemical composition of PM_2.5 filter samples from a measurement campaign performed between January 2004 and April 2005 are analysed. Positive matrix factorisation is applied as the receptor model to detect and quantify the various source contributions. For the same observational period and site, dispersion model calculations using the Air Quality Management system, AirQUIS, are performed. The results identify significant differences between the dispersion and receptor model source apportionment, particularly for wood burning and traffic induced suspension. For wood burning the receptor model calculations are lower, by a factor of 0.54, but for the traffic induced suspension they are higher, by a factor of 7.1. Inverse modelling, based on regression of the dispersion model source contributions and the PM_2.5 concentrations, indicates similar discrepancies in the emissions inventory. In order to assess if the differences found at the one site are generally applicable throughout Oslo, the individual source category emissions are rescaled according to the receptor modelling results. These adjusted PM_2.5 concentrations are compared with measurements at four independent stations to evaluate the updated inventory. Statistical analysis shows improvement in the estimated concentrations for PM_2.5 at all sites. Similarly, inverse modelling is applied at these independent sites and this confirms the validity of the receptor model results.     

Freight shipment modal split and its environmental impacts: An exploratory study

Freight transportation activities are responsible for a large share of air pollution and greenhouse gas emissions in the United States. Various freight transportation modes have significantly different impacts on air quality and environmental sustainability, and this highlights the need for a better understanding of interregional freight shipment mode choices. This paper develops a binomial logit market share model to predict interregional freight modal share between truck and rail as a function of freight and shipment characteristics. This model can be used to estimate the impacts of various factors, such as oil price, on shippers’ mode choice decisions. A set of multiyear freight and geographical information databases was integrated to construct regression models for typical freight commodities. The atmospheric impact levels incurred by different freight modal choice decisions are analyzed to provide insights on the relationship among freight modal split, oil price change, and air quality.

Implications:

Freight transportation has become a major source of energy consumption and air pollution, and emissions rates vary significantly across different modes. Understanding freight shipment mode choice under various economic and engineering factors will help assess the environmental impacts of freight shipment systems at the national level. This paper develops a binomial logit model for two dominating modes (truck and rail) and shows how this model is incorporated into an environmental impact analysis. The framework will be useful to policy makers to assess the impacts of freight movements on air quality and public health and to mitigate those adverse impacts.     

Air Quality in Selected Megacities

Abstract

About half of the world's population now lives in urban areas because of the opportunity for a better quality of life. Many of these urban centers are expanding rapidly, leading to the growth of megacities, which are often defined as metropolitan areas with populations exceeding 10 million inhabitants. These concentrations of people and activity are exerting increasing stress on the natural environment, with impacts at urban, regional and global levels. In recent decades, air pollution has become one of the most important problems of megacities. Initially, the main air pollutants of concern were sulfur compounds, which were generated mostly by burning coal. Today, photochemical smog—induced primarily from traffic, but also from industrial activities, power generation, and solvents—has become the main source of concern for air quality, while sulfur is still a major problem in many cities of the developing world. Air pollution has serious impacts on public health, causes urban and regional haze, and has the potential to contribute significantly to global climate change. Yet, with appropriate planning megacities can efficiently address their air quality problems through measures such as application of new emission control technologies and development of mass transit systems.

This review is focused on nine urban centers, chosen as case studies to assess air quality from distinct perspectives: from cities in the industrialized nations to cities in the developing world. This review considers not only megacities, but also urban centers with somewhat smaller populations, for while each city—its problems, resources, and outlook—is unique, the need for a holistic approach to complex environmental problems is the same. There is no single strategy to reduce air pollution in megacities; a mix of policy measures will be needed to improve air quality. Experience shows that strong political will coupled with public dialogue is essential to effectively implement the regulations required to address air quality.     

Derivation of exemption formulas for air quality regulatory applications

The regulatory agencies and the industries have the responsibility for assessing the environmental impact from the release of air pollutants, and for protecting environment and public health. The simple exemption formula is often used as a criterion for the purpose of screening air pollutants. That is, the exemption formula is used for air quality review and to determine whether a facility applying for and described in a new, modified, or revised air quality plan is exempted from further air quality review. The Bureau of Ocean Energy Management’s (BOEM) air quality regulations are used to regulate air emissions and air pollutants released from the oil and gas facilities in the Gulf of Mexico. If a facility is not exempt after completing the air quality review, a refined air quality modeling will be required to regulate the air pollutants. However, at present, the scientific basis for BOEM’s exemption formula is not available to the author. Therefore, the purpose of this paper is to provide the theoretical framework and justification for the use of BOEM’s exemption formula. In this paper, several exemption formulas have been derived from the Gaussian and non-Gaussian dispersion models; the Gaussian dispersion model is a special case of non-Gaussian dispersion model. The dispersion parameters obtained from the tracer experiments in the Gulf of Mexico are used in the dispersion models. In this paper, the dispersion parameters used in the dispersion models are also derived from the Monin-Obukhov similarity theory. In particular, it has been shown that the total amount of emissions from the facility for each air pollutant calculated using BOEM’s exemption formula is conservative.

Implications:?The operation of offshore oil and gas facilities under BOEM’s jurisdiction is required to comply with the BOEM’s regulations. BOEM’s air quality regulations are used to regulate air emissions and air pollutants released from the oil and gas facilities in the Gulf of Mexico. The exemption formulas have been used by BOEM and other regulatory agencies as a screening tool to regulate air emissions emitted from the oil and gas and other industries. Because of the BOEM’s regulatory responsibility, it is important to establish the scientific basis and provide the justification for the exemption formulas. The methodology developed here could also be adopted and used by other regulatory agencies.     

Evaluation of air quality zone classification methods based on ambient air concentration exposure

Air quality zones are used by regulatory authorities to implement ambient air standards in order to protect human health. Air quality measurements at discrete air monitoring stations are critical tools to determine whether an air quality zone complies with local air quality standards or is noncompliant. This study presents a novel approach for evaluation of air quality zone classification methods by breaking the concentration distribution of a pollutant measured at an air monitoring station into compliance and exceedance probability density functions (PDFs) and then using Monte Carlo analysis with the Central Limit Theorem to estimate long-term exposure. The purpose of this paper is to compare the risk associated with selecting one ambient air classification approach over another by testing the possible exposure an individual living within a zone may face. The chronic daily intake (CDI) is utilized to compare different pollutant exposures over the classification duration of 3 years between two classification methods. Historical data collected from air monitoring stations in Kuwait are used to build representative models of 1-hr NO₂ and 8-hr O₃ within a zone that meets the compliance requirements of each method. The first method, the “3 Strike” method, is a conservative approach based on a winner-take-all approach common with most compliance classification methods, while the second, the 99% Rule method, allows for more robust analyses and incorporates long-term trends. A Monte Carlo analysis is used to model the CDI for each pollutant and each method with the zone at a single station and with multiple stations. The model assumes that the zone is already in compliance with air quality standards over the 3 years under the different classification methodologies. The model shows that while the CDI of the two methods differs by 2.7% over the exposure period for the single station case, the large number of samples taken over the duration period impacts the sensitivity of the statistical tests, causing the null hypothesis to fail. Local air quality managers can use either methodology to classify the compliance of an air zone, but must accept that the 99% Rule method may cause exposures that are statistically more significant than the 3 Strike method.

Implications: A novel method using the Central Limit Theorem and Monte Carlo analysis is used to directly compare different air standard compliance classification methods by estimating the chronic daily intake of pollutants. This method allows air quality managers to rapidly see how individual classification methods may impact individual population groups, as well as to evaluate different pollutants based on dosage and exposure when complete health impacts are not known.     

Air quality mapping using GIS and economic evaluation of health impact for Mumbai City,India

Mumbai, a highly populated city in India, has been selected for air quality mapping and assessment of health impact using monitored air quality data. Air quality monitoring networks in Mumbai are operated by National Environment Engineering Research Institute (NEERI), Maharashtra Pollution Control Board (MPCB), and Brihanmumbai Municipal Corporation (BMC). A monitoring station represents air quality at a particular location, while we need spatial variation for air quality management. Here, air quality monitored data of NEERI and BMC were spatially interpolated using various inbuilt interpolation techniques of ArcGIS. Inverse distance weighting (IDW), Kriging (spherical and Gaussian), and spline techniques have been applied for spatial interpolation for this study. The interpolated results of air pollutants sulfur dioxide (SO₂), nitrogen dioxide (NO₂) and suspended particulate matter (SPM) were compared with air quality data of MPCB in the same region. Comparison of results showed good agreement for predicted values using IDW and Kriging with observed data. Subsequently, health impact assessment of a ward was carried out based on total population of the ward and air quality monitored data within the ward. Finally, health cost within a ward was estimated on the basis of exposed population. This study helps to estimate the valuation of health damage due to air pollution.

Implications: Operating more air quality monitoring stations for measurement of air quality is highly resource intensive in terms of time and cost. The appropriate spatial interpolation techniques can be used to estimate concentration where air quality monitoring stations are not available. Further, health impact assessment for the population of the city and estimation of economic cost of health damage due to ambient air quality can help to make rational control strategies for environmental management. The total health cost for Mumbai city for the year 2012, with a population of 12.4 million, was estimated as USD8000 million.     

Objectives and Design of Central California's 1995 Integrated Monitoring Study of the California Regional PM10/PM2.5 Air Quality Study

ABSTRACT

The 1995 Integrated Monitoring Study (IMS95) is part of the Phase 1 planning efforts for the California Regional PM_10/PM_2.5 Air Quality Study. Thus, the overall objectives of IMS95 are to (1) fill information gaps needed for planning an effective field program later this decade; (2) develop an improved conceptual model for pollution buildup (PM10, PM2.5, and aerosol precursors) in the San Joaquin Valley; (3) develop a uniform air quality, meteorological, and emissions database that can be used to perform initial evaluations of aerosol and fog air quality models; and (4) provide early products that can be used to help with the development of State Implementation Plans for PM_10. Consideration of the new particulate matter standards were also included in the planning and design of IMS95, although they were proposed standards when IMS95 was in the planning process.     

The Australian Air Quality Forecasting System: The Use of Green Scenarios of Motor Vehicle Usage as an Educational Tool

Abstract

The Australian Air Quality Forecasting System (AAQFS) is one of several newly emerging, high-resolution, numerical air quality forecasting systems. The system is briefly described. A public education application of the air quality impact of motor vehicle usage is explored by computing the concentration and dosage of particulate matter less than 10 µm in aerodynamic diameter (PM₁₀) for a commuter traveling to work between Geelong and Melbourne, Victoria, Australia, under “business-as-usual” and “green” scenarios. This application could be routinely incorporated into systems like AAQFS. Two methodologies for calculating the dosage are described: one for operational use and one for more detailed applications. The Clean Air Research Programme-Personal Exposure Study in Melbourne provides support for this operational methodology. The more detailed methodology is illustrated using a system for predicting concentrations due to near-road emissions of PM₁₀ andapplied in Sydney.     

Modeling traffic air pollution in street canyons in New York City for intra-urban exposure assessment in the US Multi-Ethnic Study of atherosclerosis and air pollution

We evaluated the Danish AirGIS air quality and exposure model system using air quality measurement data from New York City in the Multi-Ethnic Study of Atherosclerosis and Air Pollution (MESA Air). Measurements were used from three US EPA Air Quality System (AQS) monitoring stations and a comprehensive MESA Air measurement campaign including about 150 different locations and about 650 samples of about 2 week measurements of NO_x, NO₂ and PM_2.5. AirGIS is a deterministic exposure model system based on the dispersion models Operational Street Pollution Model (OSPM) and the Urban Background Model (UBM). The UBM model reproduced the annual levels within 1–26% depending on station and pollutant at the three urban background EPA monitor stations, and generally reproduced well the seasonal and diurnal variation. The full model with OSPM and UBM reproduced the MESA Air measurements with a correlation coefficient of r² = 0.51 for NO_x, r² = 0.28 for NO₂ and r² = 0.73 for PM_2.5.