Fenton体系降解水中偶氮染料的研究

研究了Fenton体系对于水溶液中偶氮染料橙G(orange G,OG)的降解,反应30 min后,在[Fe2+]0=0.1mmol/L、[H2O2]0=10 mmol/L、pH=3.0的条件下,初始浓度为20 mg/L的OG的去除率达到99%以上。与H2O2相比,OG的降解速率随着Fe2+不同投加量的变化更为敏感。Fe2+和H2O2初始浓度较高时,反应过程中的Fe2+的浓度维持在一个较低的水平,OG的降解速率较快。腐殖酸对OG在Fenton体系中的降解影响表现出明显的阻碍作用,并且随着腐殖酸浓度的增加,抑制作用越来越大。     

磁性膨润土的制备、表征及类Fenton催化降解橙黄Ⅱ

以铝柱撑膨润土和铁盐为原料,采用共沉淀法制备纳米Fe3O4负载的磁性膨润土复合材料。采用X射线衍射(XRD)、扫描电子显微镜(SEM)和比表面孔隙分析(BET)对样品进行表征,研究了磁性膨润土对橙黄Ⅱ的类Fenton催化降解性能,并考察了催化剂用量、温度和初始pH、H2O2初始浓度等因素对降解效果的影响。结果表明,Fe3O4均匀负载在膨润土表面,未发生明显团聚,并且改善了膨润土的孔隙结构,增加了其比表面积。在磁性膨润土用量为0.6 g/L,温度为40℃,pH为3.0,H2O2初始浓度为21 mmol/L的条件下,0.5 mmol/L橙黄Ⅱ溶液在180 min内色度去除率和UV254去除率分别达到100%和97%,且催化剂重复使用4次效果稳定。     

多羧酸改良硫代光-Fenton处理有机染料废水

使用EDDS(乙二胺二琥珀酸)螯合Fe(Ⅲ),在光照过程中活化过硫酸盐/亚硫酸盐产生硫酸根自由基,并用于处理水体中的染料橙黄Ⅱ,考察过硫酸盐/亚硫酸盐初始浓度,Fe(Ⅲ)-EDDS初始浓度以及溶液初始pH对橙黄Ⅱ降解效果的影响,并获得处理效果较好的优化体系。结果表明,Na_2SO_3-Fe(Ⅲ)-EDDS体系中,[Na_2SO_3]=5 mmol·L~(-1),[Fe(Ⅲ)-EDDS]=0.05 mmol·L~(-1),pH=3.0时,60 min内橙黄Ⅱ降解效率达98%;Na_2S_2O_8-Fe(Ⅲ)-EDDS体系中,[Na_2S_2O_8]=10 mmol·L~(-1),[Fe(Ⅲ)-EDDS]=0.50 mmol·L~(-1),pH=7.0时,120 min内橙黄Ⅱ降解效率达99%。两个体系中,Fe(Ⅲ)-EDDS均存在最佳浓度,增大或减小均导致效率降低。Na_2SO_3-Fe(Ⅲ)-EDDS体系中,溶液初始pH越大,橙黄Ⅱ降解效率越低。Na_2S_2O_8-Fe(Ⅲ)-EDDS体系中,pH高于或低于7.0时橙黄Ⅱ降解效率均降低。Na_2SO_3-Fe(Ⅲ)-EDDS体系中,亚硫酸钠浓度越大橙黄Ⅱ降解效率越高。Na_2S_2O_8-Fe(Ⅲ)-EDDS体系中,过硫酸钠存在最佳浓度,增大或减小均导致降解效率降低。     

微波诱导AC/Cu、AC/Fe催化非均相Fenton 反应催化降解垃圾渗滤液

采用活性炭载体负载Cu、Fe为催化剂,在微波诱导作用下,对垃圾渗滤液污染物进行降解。实验结果表明,活性炭负载金属前经适当浓度硝酸浸泡处理后,催化剂对COD去除率提高可超过15%,过高硝酸盐浓度对COD去除有不利影响;催化剂对COD去除率随Cu、Fe金属负载量增加呈先增加后降低的趋势,催化剂对Cu、Fe的最佳负载量分别为质量百分比2.11%和1.12%。对于AC-Cu体系,在初始pH=3,H2O2投加量为4.98×103mg/L,催化剂用量为5.0×103mg/L,420 W功率下微波辐射10 min时,垃圾渗滤液COD去除率可达到84.13%;对于AC-Fe体系,当H2O2投加量为0.33×103mg/L,催化剂AC-Fe用量为2.0×104mg/L,420 W功率下微波作用10 min时,垃圾渗滤液COD去除率为60.16%。分析2种催化剂对COD去除差异的原因,可能是催化剂AC-Cu表面单分子分布的阈值比AC-Fe高。降解液的pH值对AC-Cu体系、AC-Fe体系COD去除影响存在拐点,最高COD去除率点对应的降解液pH值为3。微波辐射功率较低时,体系COD去除率随辐射功率增加而增加;辐射功率较高时,高温下垃圾渗滤液中有机硫化物分解成小分子硫化物,对催化剂活性存在一定抑制作用。     

掺杂负载型纳米TiO2降解橙黄G的光催化活性及其动力学研究

采用溶胶-凝胶法和浸渍-焙烧法制备了掺杂Sn(Ⅳ)的TiO2/AC光催化剂,以偶氮染料橙黄G为目标降解物,对光催化反应条件进行了优化.结果表明:利用Sn(Ⅳ)掺杂量为2.5 at.%的TiO2/AC光催化剂,在进水浓度50 mg/L,催化剂的用量12.5 g/L,pH值2.0,H2O21.5 mL/L,主波长为365 nm的300W高压汞灯光照条件下,反应60 min,橙黄G的光催化去除率可达99.1%.该反应符合Langmuir-Hinshelwood动力学方程,其速控步为吸附反应.共存阴离子SO42-和H2PO4-,对橙黄G的光催化降解反应均有一定的抑制作用.     

MnO2表面结合Fe(Ⅱ)对三氯乙烯的还原脱氯作用

通过批量实验研究了Fe(Ⅱ)、MnO2和MnO2表面吸附Fe(Ⅱ)这3种体系对溶液中三氯乙烯的还原脱氯作用。发现Fe(Ⅱ)吸附在MnO2表面时,对三氯乙烯的脱氯作用最强,氯代降解产物为顺-二氯乙烯(cis-DCE),且反应符合准一级动力学。进一步实验表明,保持Fe(Ⅱ)浓度为1 mmol/L,反应速率常数kobs和三氯乙烯去除率随pH升高(5.0～9.0)而增加,最大值分别为1.62×10-1h-1、70.4%;固定pH=7.0,kobs和三氯乙烯去除率随其Fe(Ⅱ)浓度增加(1～3mmol/L)而增大。Fe(Ⅱ)浓度继续增加,kobs和三氯乙烯去除率反而减小。pH=7.0,Fe(Ⅱ)浓度为3 mmol/L时,kobs和三氯乙烯去除率达到最大值,分别为2.86×10-1h-1和85.7%。     

纳米铁酸铜催化过硫酸盐降解酸性红FRL

采用共沉淀法-焙烧制备纳米铁酸铜催化剂,利用扫描电镜(SEM)、X射线光电子能谱(XPS)和X射线衍射(XRD)对催化剂进行表征。以酸性红FRL为降解目标物,研究此催化剂催化过硫酸钠降解酸性红FRL的性能。考察了氧化剂浓度、催化剂用量和初始染料浓度对降解的影响。结果表明:催化剂经700℃焙烧3 h,可得到完整晶相的Cu Fe2O4;当初始污染物浓度为20 mg/L,过硫酸盐浓度为2.0 g/L,催化剂用量为2.0 g/L时,降解2.5 h,酸性红FRL染料溶液的降解率可达85.3%。实验所得催化剂可重复使用5次,同时酸性红FRL降解过程遵循准一级动力学方程。     

钴金属-有机骨架活化过硫酸钠降解废水中的盐酸土霉素

采用新制备的钴金属-有机骨架(Co-MOF)和过硫酸钠(PS)分别作为催化剂和氧化剂,并通过CoMOF活化PS降解废水中的盐酸土霉素,考察Co-MOF浓度、PS浓度、pH及温度对降解盐酸土霉素的影响。SEM、TEM、XRD及XPS等结果证明,Co-MOF成功地被合成。降解实验结果表明,与单独的Co-MOF、PS相比,Co-MOF/PS的降解性能有大幅度的提高。当pH=5、温度30℃、Co-MOF为200 mg·L~(-1)以及PS为2 000 mg·L~(-1)时,5 min后对20 mg·L~(-1)盐酸土霉素的降解率最高达到97.1%。在催化剂的重复使用实验中,Co-MOF第4次运行对盐酸土霉素的降解率由97.1%(第1次)降低至82.1%,这表明Co-MOF材料可以重复利用降解盐酸土霉素。Co-MOF降解盐酸土霉素实验反应前后的XRD和XPS数据表明Co-MOF具备良好的稳定性。以上研究结果可为新型高效降解体系的开发及其在水环境污染控制领域的应用提供参考。     

活性炭负载金属氧化物催化臭氧氧化甲硝唑

采用浸渍法制备了Fe、Ni、Ag、Ce 4种金属氧化物负载活性炭(MeOx/AC)催化剂,并用于甲硝唑(MNZ)的催化臭氧氧化降解,以考察其催化活性.在20 mg/h的臭氧投加量下,催化剂的加入(0.5 g)对MNZ(C0=5 mg/L;pH=5.5)的氧化和矿化有明显改善,其中NiOX/AC催化剂表现出较好的催化活性...     

NiO/AC催化臭氧氧化去除水中的苯酚

采用低温湿式浸渍法制备了负载氧化镍/活性炭(简称NiO/AC)催化剂。在不同pH、叔丁醇浓度等条件下,对NiO/AC与臭氧联合催化臭氧氧化苯酚的降解效果等进行了研究。用XRD、SEM及BET技术分析了活性炭与催化剂的组成、形貌及结构变化。结果表明,镍以棒状氧化镍的形式负载在活性炭表面,与AC相比,NiO/AC比表面积减少了47.9%。在O3/NiO/AC与苯酚的反应体系中,反应遵循羟基自由基(HO.)机理,苯酚的去除率比单独臭氧氧化提高了29%,且与溶液pH呈正相关。NiO/AC催化性能较稳定,镍离子最大析出浓度仅为7 mg/L,可重复使用。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染