基于正交实验的水质COD在线测试最优消解条件

在自主研发的一套COD在线监测系统上根据正交实验结果确定臭氧协同紫外在线检测水体COD的最优消解条件。研究了影响消解效率的4个变量:进臭氧量、消解时间、消解温度以及消解溶液的pH。在实验中采用4因素3水平L9(34)矩阵进行研究,忽略4因素之间的相互作用。结果表明,COD在小于100 mg·L~(-1)时,臭氧协同紫外在线检测水体COD的最优消解条件是:进臭氧量为160~190 mg,消解时间为15 min,消解温度为30℃,消解溶液pH值为4~6。实验证明,对于COD不超过100 mg·L~(-1)的水样消解率可达到98%,对于含苯环有机物消解率也均在95%以上。     

一种检测水体总氮的多技术协同氧化消解装置

在分析比较前人方法的基础上，研究开发了一套集臭氧、紫外、超声雾化、高压静放电等多技术协同的氧化消解装置，对含氮水样进行连续消解，将水中含氮物质中的N氧化为NO3-，从而测定水中的总氮。通过实验可以确定最佳消解条件，计算出总氮氧化的转化率，并进行精密度、准确度检验。本法具有无需添加化学氧化剂，总氮氧化率高和消解速度快，精密度、准确度高等特点。     

马夹河COD与BOD_5的相关性探讨

一、前言 化学需氧量(COD)是指示水体被还原性物质污染的主要指标.还原性物质包括各种有机物,亚硝酸盐,亚铁盐和硫化物等.但水样受有机物污染是极为普遍的,因此化学需氧量可做有机物相对含量的指标之一.我们对小清河的COD和BOD_5进行了实验,由于水体污染很严重,成份复杂,水体的变化性大二者之间不成正比,相关性不明显.但对污染很轻,COD在20mg/l以下水体相对稳定的马夹河,却成正比具有明显的相关性.可以用COD来换算BOD_5,也可以用BOD_5来换算COD.     

自配消解液分光光度法测定污水中的COD

以自配消解液代替ThermoFisher公司AQ4001COD测定系统的专用消解液，比较了自配消解液分光光度法与国家标准重铬酸钾法(GB 11914-1989)测定化学需氧量(COD)的差异。对比试验表明，自配消解液分光光度法测定COD的结果精确度和准确度高，与国家标准方法无显著性差异。自配消解液分光光度法测定水样COD值的相对标准偏差;低量程(30～150 mg/L)为1.38%～2.53%，中量程(0～1 500 mg/L)为0.47%～3.63%，高量程（2 000～15 000 mg/L）为0.17%～3.53%，在国家标准方法测试水样COD值的允许误差范围内。除制革废水外，自配消解液可以代替AQ4001COD测定系统的专用消解液，适用不同量程范围内污水COD的测定。自配消解液分光光度法具有试剂使用量少、速度快、经济、二次污染小等优点，值得在环境科学领域及废水水质监测中推广应用。     

臭氧/活性炭/真空紫外光联用处理甲基肼废水的影响因素

研究比较了臭氧氧化(O3)、臭氧/活性炭氧化(O3/AC)、真空紫外/臭氧(VUV/O3)、真空紫外/臭氧/活性炭氧化(VUV/O3/AC)对甲基肼废水的处理效果,以甲基肼和COD去除率为指标,其中VUV/O3/AC最为有效。考察了活性炭投加量、臭氧投加量、初始pH值和活性炭使用次数等因素的影响。结果表明,反应最佳工艺条件为臭氧投加4.2 mg·min~(-1)、pH值为9.60、活性炭投加量为6 g·L~(-1)。反应60 min,甲基肼去除率可达99.3%,COD去除率可达75.7%。同时,探究了活性炭的重复使用效果,分析了反应过程的中间产物。     

紫外-近红外光谱法测定废水COD含量

针对传统方法测定化学需氧量(COD)药剂成本高、检测效率低、连续监测难、废液二次污染等问题,基于现有的紫外-可见光与近红外光谱法测量COD技术,研究了综合利用紫外光谱与近红外光谱中的信息来预测废水中COD含量的可行性。实验采集了100个工厂现场水样,每一水样分成两组:一组测其190~2 300 nm波长范围的光谱数据,另一组利用传统方法测其COD,并把该方法得到的结果作为标定该水样光谱的标准值,对水样光谱用偏最小二乘法(PLS)建立废水样的COD预测模型。经验证预测值与实测值的相关度为0.967 1,验证标准误差值为24.8 mg·L~(-1),具有较好的预测效果。     

引黄水臭氧预氧化强化混凝处理及安全性研究

分析了山西省太原段的引黄水水质,探讨了臭氧预氧化强化混凝处理引黄水的适用性、处理效果及安全性。结果表明,引黄水原水中的COD含量较高,而Br-未检出,提示可以采用臭氧预氧化强化混凝处理;总体来说,臭氧低投加量(0.52～0.98mg/L)时的助凝效果更为显著,在不同的聚合氯化铝(PAC)投加量下的除浊效果都优于常规混凝处理;单独投加臭氧时,随着臭氧投加量的增加,水体紫外吸光度(UV254)逐渐降低,当臭氧投加量为2.52mg/L时,UV254去除率为44%;虽然常规混凝处理即可控制出水的浊度和UV254,但由于混凝剂投加量大,综合效益较低,而臭氧预氧化在一定程度上能起到助凝作用,也能对水体UV254起到良好的控制作用;从甲醛、BrO3-产生量控制的角度来看,太原段引黄水水质适用臭氧预氧化强化混凝处理,安全性较好。     

UV/O_3-化学沉淀-厌氧/好氧法处理合成革废水

为了降低合成革废水的毒性,提高废水的可生化性,采用臭氧紫外催化氧化+化学沉淀组成预处理,后经生物法处理,取得了较好的处理效果。结果表明:化学需氧量(COD)、二甲基甲酰胺(DMF)和二甲胺(DMA)的平均去除率分别达到99%、96%%和96%左右。该工艺克服了传统生物处理中废水的可生化性差、无法提供足够的碳源供生物脱氮等问题,而且简单、经济,对于该废水治理具有推广应用价值。     

镀镍漂洗废水中有机物的臭氧氧化处理研究

用臭氧氧化处理镀镍漂洗废水中的有机物,主要考察pH、臭氧投加量、废水初始COD浓度、温度等因素对处理效果的影响,并对反应机理进行初步的探讨.实验结果表明,废水的COD去除率随pH的增大而升高,比较适宜的pH为6～7;适当地增加臭氧投加量有利于提高COD去除率;在一定温度范围(15～35℃)内,提高反应温度有利于废水中有机物的降解;当臭氧投加量为20 mg/(min·L),对于初始COD为56 mg/L、pH 6.5的实际镀镍漂洗废水,在25 ℃的条件下氧化100min,出水COD降至10mg/L,COD去除率达到82%;在臭氧氧化镀镍漂洗废水的反应中,部分有机物的降解是在Ni2 的催化下由臭氧分解生成氧化能力更强的自由基来完成.臭氧氧化可作为镀镍漂洗废水处理回用的预处理工艺.     

Ti(Ⅳ)催化臭氧化预处理酸性难降解制药废水

考察了酸性条件下Ti(Ⅳ)催化臭氧化预处理医药废水的效能,关联了废水氧化度与可生化性(BOD5/COD)的关系。结果表明,酸性条件下O3和O3/H2O2的氧化效率明显低于Ti(Ⅳ)/H2O2/O3。原始pH条件(3.5)下,Ti(Ⅳ)/H2O2/O3体系Ti(Ⅳ)离子和H2O2的最佳浓度分别为10 mg/L和200 mg/L。调节pH值至5.0处理120 min,制药废水的化学需氧量(COD)和总有机碳(TOC)的去除率分别为56.13%和31.49%。此时水样氧化度从原来的0.388提升到了0.608,BOD5/COD值从原来的0.019升至0.297,两者呈现较好的正相关性。以上结果表明,增大pH可以提高Ti(Ⅳ)/H2O2/O3的处理效果;此外,可以考虑利用氧化度的大小来快速判断水样的可生化性。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.